Craftsman 917387370 Owner’s Manual

Owner's Manual

IcRnmMnw,I

ROTARY LAWN MOWER

6.0 Horsepower

22" Side Discharge

Model No.

917.387370

CAUTION:

Read and follow all Safety Rules and Instructions

before operating this equipment

Sears, Roebuck and Co., Hoffman Estates, IL 60179 U.S.A.

Visit our Craftsman website: www,sears.com/craffsman

Warranty ................................................... 2

Safety Rules .......................................... 2-4

Assembly / Pre-Operation ........................ 5

Operation ............................................... 6-9

Maintenance Schedule ........................... 10

Maintenance ...................................... 10-13

LIMITED TWO YEAR WARRANTY ON CRAFTSMAN POWER MOWER For two years from date of purchase, when this Craftsman Lawn Mower is maintained,

lubricated, and tuned up according to the operating and maintenance instructions in the

owner's manual, Sears will repair free of charge any defect in material or workmanship.

If this Craftsman Lawn Mower is used for commercial or rental purposes, this warranty applies for only 90 days from the date of purchase.

This Warranty does not cover:

• Expendable items which become worn during normal use, such as rotary mower blades, blade adapters, belts, air cleaners and spark plug.

• Repairs necessary because of operator abuse or negligence, including bent crank- shafts and the failure to maintain the equipment according to the instructions con- tained in the owner's manual.

Warranty service is available by returning the Craftsman power mower to the nearest Sears Service Center/Department in the United States. This warranty applies only while

this product is used in the United States. This Warranty gives you specific legal rights, and you may also have other rights which

vary from state to state. SEARS, ROEBUCK AND CO., D/817 WA, HOFFMAN ESTATES, ILLINOIS 60179

Product Specifications ............................ 11

Service and Adjustments ................... 13-14

Storage .............................................. 14-15

Troubleshooting ................................. 15-16

Repair Parts ....................................... 32-37

Sears Service .......................... Back Cover

IMPORTANT: This cutting machine is capable ofamputating hands and feet and throw- ing objects. Failure to observe the following safety instructionscould result in serious

injuryor death. _J_ook for this symbol to point out

important safety precautions. Itmeans

CAUTION!!! BECOME ALERT!!! YOUR SAFETY IS INVOLVED,

=oAWARNING:Battery posts, terminals and

related accessories contain lead and lead compounds, chemicals known to the State

of California to cause cancer and birth defects or other reproductiveharm. Wash

AWARNING: In order to prevent ac-

hands after handling.

cidental starting when setting up, trans- porting, adjustingor making repairs, always disconnect spark plug wire and

place wire where itcannot contact spark plug.

AWARNING: Engine exhaust, some of its constituents, and certain vehicle compo-

nents contain or emit chemicals known to the State of California to cause cancer

and birth defects or other reproductive

harm. 2

_rkCAUTION: Muffler and other engine

parts become extremely hot during

operation and remain hot after engine has stopped. To avoid severe burns on contact, stay away from these areas.

I.GENERAL OPERATION

• Read,understand,and follow all

instructions on the machine and in the

manual(s) before starting. Be thoroughly

familiar with the controls and the proper

use of the machine before starting.

• Do not put hands or feet near or under

rotating parts. Keep clear of the dis-

charge opening at all times.

• Only allow responsible individuals, who are familiar with the instructions, to

operate the machine.

• Clear the area of objects such as rocks, toys, wire, bones, sticks, etc., which

could be picked up and thrown by the blade.

• Be sure the area is clear of other people before mowing. Stop machine if anyone

enters the area.

• Do not operate the mower when bare-

foot or wearing open sandals. Always

wear substantial foot wear.

• Do not pull mower backwards unless

absolutely necessary. Always look down and behind before and while moving

backwards.

• Do not operate the mower without

proper guards, plates, grass catcher or

other safety protective devices in place.

• See manufacturer's instructions for proper operation and installation of

acoessodes. Only use accessories ap-

proved by the manufacturer.

• Stop the blade(s) when crossing gravel

drives, walks, or roads.

• Stop the engine (motor) whenever you

leave the equipment, before cleaning the mower or unclogging the chute.

• Shut the engine (motor) off and wait until the blade comes to complete stop

before removing grass catcher.

• Mow only in daylight or good artificial light.

• Do not operate the machine while under the influence of alcohol or drugs.

• Never operate machine in wet grass.

Always be sure of your footing: keep a firm hold on the handle and walk; never

run.

• Disengage the self-propelled mech-

anism or drive clutch on mowers so equipped before starting the engine

(motor).

• If the equipment should start to vibrate

abnormally, stop the engine (motor) and check immediately for the cause. Vibra-

tion is generally a warning of trouble.

• Always wear safety goggles or safety

glasses with side shields when oper-

ating mower.

II. SLOPE OPERATION

Slopes are a major factor related to slip and fall accidents which can result in

severe injury. All slopes require extra cau- tion. If you feel uneasy on a slope, do not

mow it.

DO:

• Mow across the face of slopes: never up and down. Exercise extreme caution

when changing direction on slopes.

• Remove obstacles such as rocks, tree limbs, etc.

• Watch for holes, ruts, or bumps. Tall grass can hide obstacles.

DO NOT:

• Do not trim near drop-offs, ditches or embankments. The operator could lose

footing or balance.

• Do not trim excessively steep slopes.

• Do not mow on wet grass. Reduced foot-

ing could cause slipping.

IlL CHILDREN Tragic accidents can occur if the operator

is not alert to the presence of children. Children are often attracted to the machine

and the mowing activity. Never assume that children will remain where you last

saw them.

• Keep children out of the trimming area and under the watchful care of another

responsible adult.

• Be alert and turn machine off if children enter the area.

• Before and while walking backwards, look behind and down for small children.

• Never allow children to operate the ma- chine.

• Use extra care when approaching blind corners, shrubs, trees, or other objects

that may obscure vision.

IV. SERVICE

• Use extra care in handling gasoline and other fuels. They are flammable and

vapors are explosive.

- Use only an approved container.

- Never remove gas cap or add fuel

with the engine running. Allow

engine to cool before refueling. Do

not smoke.

- Never refuel the machine indoors.

- Never store the machine or fuel

container inside where there is an

open flame, such as a water heater.

• Never run a machine inside a closed area.

• Never make adjustments or repairs with the engine (motor) running. Disconnect

the spark plug wire, and keep the wire

away from the plug to prevent accidental starting.

• Keep nuts and bolts, especially blade attachment bolts, tight and keep equip-

ment in good condition.

• Never tamper with safety devices. Check their proper operation regularly.

• Keep machine free of grass, leaves, or other debris build-up. Clean oil or fuel

spillage. Allow machine to cool before storing.

• Stop and inspect the equipment if you

• Never attempt to make wheel height adjustments while the engine (motor) is

running.

• Grass catcher components are subject to wear, damage, and deterioration,

which could expose moving parts or allow objects to be thrown. Frequently

check components and replace with manufacturer's recommended parts,

when necessary.

• Mower blades are sharp and can cut. Wrap the blade(s) or wear gloves, and

use extra caution when servicing them.

• Do not change the engine governor set- ting or overspeed the engine.

strike an object. Repair, if necessary, before restarting.

These accessories were available when this lawn mower was produced. They are not shipped with your mower. They are also available at most Sears retail outlets and ser- vice centers, Most Sears stores can also order repair parts for you, when you provide

the model number of your lawn mower. Some of these accessories may not apply to your lawn mower.

LAWN MOWER PERFORMANCE

CUPPING

DEFLECTORS

FOR

REAR DISCHARGE

LAWN MOWERS

GRASSCATCHF.R8

FOR

REARDISCHARGE

LAWNMOWERS

LAWN MOWER MAINTENANCE

MUFFLERS

BELTS BLADES

STABILIZER

FOR

SIDEDISCHARGE

GRAB8CATCHERS

LAWNMOWERS

AIR RLTERS 8PARK PLUG8

ENGINE Oil.

Read these instructions and this manual in its entirety before you attempt to assemble

or operate your new lawn mower.

IMPORTANT: This lawn mower is shipped

WITHOUT OIL OR GASOLINE in the engine. Your new lawn mower has been as-

sembled at the factory with the excep-

tion of those parts left unassembled for

shipping purposes, To ensure safe and proper operation of your lawn mower, all parts and hardware you assemble must be

tightened securely. Use the correct tools

as necessary to ensure proper tightness. All parts such as nuts, washers, bolts, etc.,

necessary to complete the assembly have been placed in the parts bag.

TO REMOVE LAWN MOWER FROM

CARTON

1. Remove loose parts included with mower,

2. Cut down two end corners of carton and lay end panel down flat.

3. Remove all packing materials except

padding between upper and lower handle and padding holding operator

presence control bar to upper handle.

4. Roll lawn mower out of carton and

check carton thoroughly for additional loose parts.

HOWTO SET UPYOUR LAWN MOWER

TO UNFOLD HANDLE

IMPORTANT: Unfold handle carefully so

as not to pinch or damage control cables.

1. Raise handles until lower handle sec- tion locks into place in mowing position.

2. Remove protective padding, raise up- per handle section into place on lower

handle and tighten both handle knobs.

3. Remove handle padding holding operator presence control bar to upper

handle.

Your lawn mower handle can be adjusted for your mowing comfort. Refer to "AD- JUST HANDLE" in the Service and Adjust-

ments section of this manual,

Operator presence

controlbar

Upper

LIFT

Mowing

position

Lower handle

TO INSTALL ATTACHMENTS Your lawn mower was shipped ready to

be used as a mulcher. To convert to bag- gingor discharging, see "TO CONVERT

MOWER" in the Operation section of this manual).

KNOW YOUR LAWN MOWER READ THIS OWNER'S MANUAL AND ALL SAFETY RULES BEFORE OPERATING

YOUR LAWN MOWER, Compare the illustrations with your lawn mower to familiarize

yourself with the location of various controls and adjustments. Save this manual for future reference,

These symbols may appear on your lawn mower or in literature supplied with the

product. Learn and understand their meaning.

CAUTION ENGINE ENGINE FAST SLOW CHOKE FUEL OIL DANGER, K]SEPHANDS

OR WARNING ON OFF AND FEET AWAY

presencecontrol bar

nob

Starter handle

Engine oilcap with dipstick

Primer

Gasoline

Muffler

guard

Wheel adjuster (on each wheel)

IMPORTANT: This lawn mower is shipped WITHOUT OIL OR GASOLINE in the engine. MEETS CPSC SAFETY REQUIREMENTS

Sears rotary walk-behind power lawn mowers conform to the safety standards of the American National Standards Institute and the U.S, Consumer Product Safety Com-

mission. The blade turns when the engine is running. Operator presence control bar - must

be held down to the handle to start the engine. Release to stop the engine.

Starter handle - used for starting engine.

Primer - pumps additional fuel from the

carburetor to the cylinderfor use when

startinga cold engine.

mower can result in foreign objects thrown into the

The operation of any lawn

eyes, which can result in severe eye damage. Always

wear safety glasses or eye shields while operating your lawn mower or performing

any adjustments or repairs. We recom- mend a standard safety glasses or wide

vision safety mask worn over spectacles.

HOWTO USEYOUR LAWN MOWER

ENGINE SPEED

The engine speed was set at the factory for optimum performance. Speed is not

adjustable. ENGINE ZONE CONTROL

/I, CAUTION: Federal regulations require an engine control to be installed on this

lawn mower in order to minimize the

risk of blade contact injury. Do not under

any circumstances attempt to defeat the function of the operator control. The blade

turns when the engine is running.

• Your lawn mower is equipped with an operator presence control bar which

requires the operator to be positioned behind the lawn mower handle to start

and operate the lawn mower.

TO ADJUST CUTTING HEIGHT

Raise wheels for low cut and lower wheels for high cut, adjust cutting height to suit

your requirements. Medium position is best for most lawns.

• To change cutting height, squeeze ad-

juster lever toward wheel. Move wheel up or down to suit your requirements.

Be sure all wheels are in the same set-

ting. NOTE: Adjuster is properly positioned when plate tab inserts into hole in lever.

Also, 9-position adjusters (if so equipped) allow lever to be positioned between the

plate tabs.

TO CONVERT MOWER Your mower is shipped ready to be used

as a mulcher. To convert to bagging or discharging:

• Lift discharge guard and remove

mulcher plate.

• Mower can now be used for side dis-

charge or optional grass catcher can be attached.

• To return to mulching operation, simply

reinstall mulcher plate as shown.

[_CAUTION: Do not run your lawn mower without discharge guard, approved grass catcher or mulcher plate in place.

Discharge _,

Housing

opening

Mulcher

Tab

RAISE WHEELS FOR LOW CUT

BEFORE STARTING ENGINE

ADD OIL

Your lawnmower is shipped without oil in the engine. For type and grade of oil to use, see "ENGINE" in the Maintenance

section of this manual.

• t, CAUTION: DO NOT overfill engine with oil, or it will smoke on startup.

1. Be sure lawnmower is level and area around oil fill is clean.

2. Remove oil dipstick from oil fill spout. Make sure that rim of spout is clean.

3. You receive a container of oil with the unit. Slowly pour the entire container

down the oil fill spout into the engine.

4. Wait one minute to allow oil to settle. Insert and tighten dipstick, then re-

move it to check oil level.

5. Always be sure to retighten oil dipstick before starting engine.

• Check oil level before each use. Add oil if needed. Fill to full line on dipstick.

• Change the oil after every 25 hours of operation or each season. You may

need to change the oil more often under

dusty, dirty conditions.

ADD GASOLINE

• Fill fuel tank to bottom of tank filler neck. Do not overfill. Use fresh, clean, regular

unleaded gasoline with a minimum of 87 octane. Do not mix oil with gasoline.

Purchase fuel in quantities that can be used within 30 days to assure fuel fresh-

Bess.

/I, CAUTION: Wipe off any spilled oil or fuel. Do not store, spill or use gasoline

,_ar an open flame.

CAUTION: Alcohol blended fuels

(called gasohol or using ethanol or metha-

nol) can attract moisture which leads to

separation and formation of acids during storage. Acidic gas can damage the fuel system of an engine while in storage. To

avoid engine problems, the fuel system should be emptied before storage of 30

days or longer. Drain the gas tank, start

the engine and let it run until the fuel lines

and carburetor are empty. Use fresh fuel next season. See Storage Instructions for

additional information. Never use engine or carburetor cleaner products in the fuel

tank or permanent damage may occur.

oil cap

GasoUne fillercap

Prime

TO START ENGINE NOTE: Due to protective coatings on the

engine, a small amount of smoke may be present during the initial use of the prod-

uct and should be considered normal.

1. To start a cold engine, push primer three (3) times before trying to start.

Use a firm push. This step is not usually necessary when starting an

engine which has already run for a few minutes.

2. Hold operator presence control bar clown to the handle and pull starter

handle quickly. Do not allow starter rope to snap back.

TO STOP ENGINE

• To stop engine, release operator pres- ence control bar.

NOTE: In cooler weather it may be neces- sary to repeat priming steps. In warmer

weather over priming may cause flooding

and engine will not start. If you do flood engine, wait a few minutes before attempt-

ing to start and do not repeat pdming

steps.

MOWING TIPS

CAUTION: Do not use de-thatcher

blade attachments on your mower, Such attachments are hazardous, will damage

your mower and could void your warranty.

• Under certain conditions, such as very tall grass, it may be necessary to raise

the height of cut to reduce pushing effort and to keep from overloading the

engine and leaving clumps of grass clip- pings. It may also be necessary to re-

duce ground speed and/or run the lawn mower over the area a second time.

• For extremely heavy cutting, reduce the width of cut by overlapping previously

cut path and mow slowly.

• For better grass bagging and most cut-

ting conditions, the engine speed should be set in the FAST position.

• For side discharge lawn mowers, cutting

in a counter-clockwise direction, start- ing at the outside of the area to be cut, spreads grass clippings more evenly

and puts less load on the engine. To keep clippings off of walkways, flower

beds, etc., make the first cuts in a clock- wise direction.

• Pores in cloth grass catchers can be-

come filled with dirt and dust with use and catchers will collect less grass. To

prevent this, regularly hose catcher off with water and let dry before using.

• Keep top of engine around starter clear and clean of grass clippings and chaff.

This will help engine air flow and extend engine life.

MULCHING MOWING TIPS

IMPORTANT: For best performance, keep mower housing free of built-up

grass and trash. See "CLEANING" in the Maintenance section of this manual.

• The special mulching blade will recut

the grass clippings many times and

reduce them in size so that as they fall onto the lawn they will disperse into

the grass and not be noticed. Also, the mulched grass will biodegrade quickly

to provide nutrients for the lawn. Always mulch with your highest engine (blade)

speed as this will provide the best recut- ting action of the blades.

• Avoid cutting your lawn when it is wet. Wet grass tends to form clumps and

interferes with the mulching action. The

best time to mow your lawn is the early afternoon. At this time the grass has

dried and the newly cut area will not be

exposed to the direct sun.

• For best results, adjust the lawn mower cutting height so that the lawn mower

cuts off only the top one-third of the grass blades. If the lawn is overgrown it will be necessary to raise the height of

cut to reduce pushing effort and to keep from overloading the engine and leaving

clumps of mulched grass. For extremely

heavy grass, reduce your width of cut by overlapping previously cut path and

mow slowly.

MAX 1/3

• Certain types of grass and grass conditions may require that an area be

mulched a second time to completely

hide the clippings. When doing a sec- ond cut, mow across or perpendicular to

the first cut path.

• Change your cutting pattern from week to week. Mow north to south one week

then change to east to west the next week. This will help prevent matting and

graining of the lawn.

MAINTENANCE SCHEDULE '/

REGULAR SERVICE /'_-/_, ,//_(_" _ _'_(7" f¢,_r_/" _ UP_II=_

Check for Loose Fasteners 1/ V /

CleardlnspectGrass Catcher

MO Clean LawnMower

Clean Under DriveCover

Check drive belt/pulleys ,j

W (PowerOropelled Mowers) !/

(Power-PropalledMowers)

R Check/Sl_q_en/Replace Blade $

Lubdc,atlon Chart V'

CleanBattery/Recharge

NE Check Engine Oil Level 1/

Change EngineC a I/t.=

G CleanAirFilter ill =

I Inspe_ Muffler

N Clean or ReplaceSpark Plug v'

E ReplaceAirRlterPaperCsrtddge 1/=

1. Chengemoreoflehwhen opera_r,gundermheavyloadorInhighambkmt_re=.

2. S_/,ce motwolin whenopemingIndrty m dusty€onditions.

3. Replecsblad_ morno_enwflenmowlnoInrandy sdl,

4 - Charge48 hoursat endof seemon.

GENERAL RECOMMENDATIONS

The warranty on this lawn mower does not cover items that have been subjected to

operator abuse or negligence. To receive

full value from the warranty, operator

must maintain mower as instructed in this manual. Some adjustments will need to be made periodically to properly maintain your unit.

All adjustments in the Service and Adjust-

ments section of this manual should be checked at least once each season.

• Once a year, replace the spark plug, clean or replace air filter element and

check blade for wear. A new spark plug and clean/new air filter element assure

proper air-fuel mixture and help your engine run better and last longer.

• Follow the maintenance schedule in this manual.

BEFORE EACH USE

• Check engine oil level.

• Check for loose fasteners,

LUBRICATION Keep unit well lubricated (See =LUBRI-

CATION CHART").

(_) Spray lubricant (_) See "ENGINE" In Maintenance section.

LUBRICATION CHART

Wheel

adjuster (on

each wheel)

I I I Discharge

.,j guard hinge

IMPORTANT: Do not oil or grease plastic wheel bearings. Viscous lubri-

cants will attract dust and dirt that will shorten the life of the self-lubricating

bearings. If you feel they must be lubricated, use only a dry, powdered

graphite type lubricant sparingly.

PRODUCT SPECIFICATIONS

Serial number: Date of purchase: Gasoline capacity / type: 1.6 Quarts (Unleaded Regular)

Oil type (API-SF-SJ): SAE 30 (above 32°F); SAE 5W-30 (below 32°F) Oil capacity: 20 Ounces

Spark plug (gap: .030") Champion RJ19LM Blade bolt torque: 35-40 ft, Ibs.

The model and serial numbers will be found on a decal on the rear of the lawn mower housing. Record both serial number and date of purchase in space provided above.

LAWN MOWER

Always observe safety rules when per- forming any maintenance.

TIRES

• Keep tires free of gasoline, oil, or insect control chemicals which can harm rub-

ber.

• Avoid stumps, stones, deep ruts, sharp objects and other hazards that may

cause tire damage.

BLADE CARE For best results, mower blade must be

kept sharp. Replace bent or damaged blades.

TO REMOVE BLADE

1. Disconnect spark plug wire from spark plug and place wire where it cannot

come in contact with spark plug.

2. Turn lawn mower on its side. Make sure air filter and carburetor are up.

3. Use a wood block between blade and mower housing to prevent blade from turning when removing blade bolt.

NOTE: Protect your hands with gloves and/or wrap blade with heavy cloth.

4. Remove blade bolt by turning counter-

clockwise.

5. Remove blade and attaching hard- ware (bolt, lock washer and hardened

washer).

NOTE: Remove the blade adapter and check the key inside hub of blade adapter.

The key must be in good condition to work properly, Replace adapter if damaged.

TO REPLACE BLADE

1. Position the blade adapter on the en- gine crankshaft. Be sure key in adapter

and crankshaft keyway are aligned.

2. Position blade on the blade adapter aligning the two (2) holes in the blade

with the raised lugs on the adapter.

3, Be sure the trailing edge of blade (op-

posite sharp edge) is up toward the engine.

4. Install the blade bolt with the lock washer and hardened washer into

blade adapter and crankshaft.

5. Use block of wood between blade and lawn mower housing and tighten the

blade bolt, turning clockwise.

• The recommended tightening torque is

35-40 ft. Ibs.

IMPORTANT: Blade bolt is grade 8 heat treated.

TO SHARPEN BLADE NOTE: We do not recommend sharpening

blade - but if you do, be sure the blade is balanced.

Care should be taken to keep the blade balanced. An unbalanced blade will

cause eventual damage to lawn mower or engine.

• The blade can be sharpened with a file

or on a grinding wheel. Do not attempt

to sharpen while on the mower.

• To check blade balance, drive a nai! into

a beam or wall. Leave about one inch of

the straight nail exposed. Place center

hole of blade over the head of the nail. If blade is balanced, it should remain in

a horizontal position. If either end of the blade moves downward, sharpen the

heavy end until the blade is balanced.

Blade adapter _ Crankshaft

B,ade'° kwas r

Dolt Hardens \

washer Trailing edge Blade adapter

GRASS CATCHER

(If purchased as an accessory)

• The grass catcher may be hosed with water, but must be dry when used.

• Check your grass catcher often for damage or deterioration. Through normal use it will

wear. If catcher needs replacing, replace onlywith a manufacturer approved replace-

ment catcher, Givethelawn mower model number when ordering.

ENGINE

LUBRICATION Use only high quality detergent oil rated with

API service classification SF-SJ. Select the oil's SAE viscosity grade according to your

expected operating temperature.

SAE VISCOSITY GRADES

NOTE: Although multi-viscosity oils (5W30, 10W30 etc.) improve starting in cold weather, these multi-viscosity oils will result in in-

creased oil consumption when used above

32°E Check your engine oil level more fre-

quently to avoid possible engine damage from running low on oil.

Change the oil after every 25 hours of operation orat least once a year if the lawn

mower is not used for 25 hours in one

year. Check the crankcase oil level before

starting the engine and after each five (5) hours of continuous use. Tighten oil plug

securely each time you check the oil level.

TO CHANGE ENGINE OIL

NOTE: Before tipping lawn mower to drain oil, drain fuel tank by running engine until fuel tank iS empty.

1. Disconnect spark plug wire from spark plug and place wire where it cannot

come in contact with spark plug.

2. Remove engine oil cap; lay aside on a clean surface.

3. Tip lawn mower on its side as shown

and drain oil into a suitable container. Rock lawn mower back and forth to re-

move any oil trapped inside of engine.

4. Wipe off any spilled oil from lawn

mower or side of engine.

5. Fill engine with oil. The engine oil capacity

is 20 oz. If oil is not completely drained

from engine, you may not need the entire container of a 20 oz. bottle of oil. Slowly

pour 3!4 of the oil from the container down the oil fill spout into the engine. 12

6. Wait one minute to allow oil to settle. Insert and tighten dipstick, then re-

move it to check oil level.

7. Continue adding small amounts of

oil and rechecking the dipstick until it reads full, DO NOT overfill, or engine

will smoke on startup,

8. Always be sure to retighten oil dipstick

before starting engine.

9. Reconnect spark plug wire to spark

plug.

Containe

AIR FILTER Your engine will not run properly and may

be damaged by using a dirty air filter,

Replace the air filter every 100 hours of operation or every season, whichever oc- curs first. Service air cleaner more often

under dusty conditions. TO CLEAN AIR FILTER

1. Loosen screw and tilt cover to remove.

2. Carefully remove cartridge,

3. Clean by gently tapping on a flat sur-

_t face. If very dirty, replace cartridge.

CAUTION: Petroleum solvents, such as

kerosene, are not to be used to clean car- tridge. They may cause deterioration of the cartridge. Do not oil cartridge. Do not use pressurized air to clean or dry cartridge.

4. Install cartridge, then replace cover

making sure the tabs are aligned with the slots in the back plate. Fasten

screw securely.

Back

Co_Br

Cover tabs

+ 28 hidden pages

Craftsman 917387370 Owner’s Manual

Specifications and Main Features

Frequently Asked Questions

User Manual