Owner's Manual
®
4°0 HORSEPOWER
22" SIDE DmSOHARGE
ROTARY LAWN _ItOWER
Model No.
917.387210
o Safety
o Assembly
e Operation
Maintenance
o EspaSol
o Repair Parts
CAUTRON:
Read and follow all
Safety Rules and Instructions
before operating this equipment
Sears, Roebuck and Co., Hoffman Estates, IL 60179
Warranty 2 Product Specifications 9
Safety Rules 2 Service and Adjustments 11
Assembly 4 Storage 12
Operation 5 Troubleshooting 13
Maintenance Schedule 8 Repair Parts 28
Maintenance 8 Parts Ordering Back Cover
LIMITED ONE YEAR WARRANTY ON CRAFTSMAN POWER MOWER
For one year frdm date ofpurchase, when this Craftsman Lawn Mower is maintained,
lubricated, arrd tuned up according to the operating and maintenance instructions in the
owner's manual, Sears will repair free of charge any defect in material or workmanship,
If this Craftsman Lawn Mower is used for commercial or rental purposes, this warranty
applies for only 90 days from the date of purchase.
This Warranty does not cover:
o Expendable items which become worn during normal use, such as rotary mower
blades, blade adapters, belts, air cleaners and spark plug,
• Repairs necessary because of operator abuse or negligence, including bent crank-
shafts and the failure to maintain the equipment according to the instructions con-
tained in the owner's manual.
Warranty service is available by returning the Craftsman power mower to the nearest
Sears Service Center/Department in the United States,. This warranty applies only while
this product is in use in the United States.
This Warranty gives you specific legal rights, and you may also have other rights which
vary from state to state.
SEARS, ROEBUCKAND CO. D/817 WA, HOFFMAN ESTATES, ILLINOIS 60179
TRAINING:
= Read this operator's manual carefully.
Become familiar with the controls and
know how to operate your mower
properly: Learn how to quickly stop
mower,
o Do not allow children to use your mower,
Never allow adults to use mower without
proper instructions
o Keep the area of operation clear of all
persons, especially small children arrd
pets,
o Use mower only as the manufacturer
intended and as described in this manual.
= Do not operate mower if it has been
dropped or damaged in any manner.
Always have damage repaired before
using your mower.
° Do not use accessory attachments that
are not recommended by the manufac-
turer. Use of such attachments may be
hazardous.
= The blade turns when the engine is
running.
PREPARATION:
o Always thoroughly check the area to be
mowed and clear it of all stones, sticks,
wires, bones, and other foreign objects.
These objects will be thrown by the blade
and can cause severe injury_
• Always wear safety glasses or eye
shields when starting and while using
your mower.
o Dress properly. Do not operate mower
when barefoot or wearing open sandals.,
Wear only solid shoes with good traction
when mowing.
o Check fuel tank before starting engine.
Do not fill gas tank indoors, when the
engine is running or when the engine is
2
hot.Allowtheenginetocoolforseveral
minutesbeforefillingthegastankClean
offanyspilledgasolinebeforestartingthe
engine
o Alwaysmakewheelheightadjustments
beforestartingyourmowerNever
attempttodothiswhiletheengineis
running,
o Mowonlyindaylightorgoodartificial
lighL
OPERATION:
= Keepyoureyesandmindonyourmower
andtheareabeingcuLDonotletother
interests distract you_
o Do not mew wet or slippery grass. Never
run while operating your mower Always
be sure of your footing -- keep a firm
hold on the handles and walk.
o Do net put hands or feet near or under
rotating parts Keep clear of the discharge
opening at all times
= Always stop the engine whenever you
leave or are not using your mower, or
before crossing driveways, walks, roads,
and any gravel--covered areas
= Never direct discharge of material toward
bystanders nor allow anyone near the
mower while you are operating it.
= Before cleaning, inspecting, or repairing
your mower, stop the engine and make
absolutely sure the blade and all moving
parts have stopped. Then disconnect the
spark plug wire and keep it away from the
spark plug to prevent accidental starting.
o Do not continue to run your mower if you
hit a foreign object Follow the procedure
outlined above, then repair any damage
before restarting and operating you
mower,
o Do not change the governor settings or
overspeed the engine, Engine damage or
personal injury may resulL
° Do not operate your mower if it vibrates
abnormally, Excessive vibration is an
indication of damage; stop the engine,
safely check for the cause of vibration
and repair as required.
o Do not run the engine indoors Exhaust
fumes are dangerous
° Never cut grass by pulling the mower
towards you Mow across the face of
slopes, never up and down or you might
lose your footing. Do not mow exces-
sively steep slopes. Use caution when
operating the mower on uneven terrain
or when changing directions -- maintain
good footing..
o Never operate your mower without
proper guards, plates, grass catcher or
other safety devices in place
MAINTENANCE AND STORAGE:
o Check the blade and the engine mount-
ing bolts often to be sure they are
tightened properly.
o Check all bolts, nuts and screws at
frequent intervals for proper tightness to
be sure mower is in safe working
condition.
. Keep all safety devices in place and
working.
o To reduce fire hazard, keep the engine
free of grass, leaves or excessive grease
and oil.
o Check grass catcher often for deteriora-
tion and wear and replace worn bags.
Use only replacement bags that are
recommended by and comply with
specifications of the manufacturer of your
mower.
o Always keep a sharp blade on your
mower.
o Allow engine to cool before storing in any
enclosure
o Never store mower with fuel in the tank
inside a building where fumes may reach
an open flame or an ignition source such
as a hot water heater, space heater,
clothes dryer, etc.
CAUTION: Always disconnect spark
plug wire and place wire where it
cannot contact spark plug in order to
prevent accidental starting when
setting up, transporting, adjusting or
making repairs,
WARNING
The engine exhaust from this product
contains chemicals known to the State
of California to cause cancer, birth
defects, or other reproductive harm.
3
Theseaccessorieswereavailablewhenthislawnmowerwasproduced+Theyarealso
availableatmostSearsretailoutletsandservicecenters.MostSearsstorescanalsoorder
repairpartsforyou,whenyouprovidethemodelnumberofyourlawnmower+Someofthese
accessoriesmaynotapplytoyourlawnmower+
LAWN MOWER PERFORMANCE
FOR REAR DISCHARGE LAWN MOWERS
CLIPPING DEFLECTOR
GRASS CATCHERS
FOR
REAR DISCHARGE
LAWN MOWERS
LAWN MOWER MAINTENANCE
MUFFLERS
BELTS BLADES BLADE ADAPTERS
Read these instructionsand this manual in its
entirety before you attempt to assemble or
operate your new lawn mower+ Your new lawn
mower has been assembled at thefactory with
the exception of those partslleft unassembled
for shipping purposes. All parts such as nuts,
washers, bolts, etc,, necessary to complete the
assembly have been placed in 8te parts bag+
To ensure safe and propet' operation of your
lawn mower, all parts and hardware you
assemble must be tightened securely. Use the o
correct toolsas necessary to ensure proper
tightness.
TO REMOVE LAWN MOWER FROIVt
CARTON
o Remove {oose parts includedwith mower.
o Cut down two end comers of carton and lay
end panel down flat+
o Remove all packing materials except
padding between upper and lower handle
and padding holding operator presence
controlbar to upper handle.
MULCHER KITS STABILIZER
FOR
SIDE DISCHARGE
GRASS CATCHERS
LAWN MQWERS
GAS CANS
+
AIR FILTERS
WHEELS
,, Roll lawn mower out of carton and check
carton thorouglyfor additional looseparts,
HOW TO SET UP YOUR LAWN
IVIOWER
TO UNFOLD HANDLE
IMPORTANT: Unfold handle carefully so as
not to pinch or damage control cables,
= Raise handles until tower handle section
locks into place in mowing position.
Remove protective padding, raise upper
handle section into place on lower handle
and tighten both handle knobs+
= Remove handle padding holding operator
presence control bar to upper handle,
o Your lawn mower handle can be adjusted
for your mowing comfort. Refer to "Adjust
Handle" inthe Service and Adjustment
section of this manual°
SPARK PLUGS
ENGINE OIL
Operator presence control bar
Lift up
Mowing
position
Lower
handle
KNOW YOUR LAWN MOWER
READ THIS OWNER'S MANUALAND SAFETY RULES BEFORE OPERATING YOUR LAWN
MOWER. Compare the illustrations with your Iawn mower to familiarize yourself with the
location of various controls and adjustments. Save this manual for future reference.
These symbols may appear on your lawn mower or in literature supplied with the product
Learn and understand their meaning.
CAUTION ENGINE ENGINE FAST SL{3W CHOKE FUEL OIL DANGER_ KEEP HANBS
OR WARNING ON OFF AND FEET AWAY
)resence control bar
Engine zone control
cable
Handle knob
Gasoline filler cap
Engine oil
filler plug
Discharge guard
Air filter
Housing
Wheel adjuster
(on each wheel)
MEETS CPSC SAFETY REQUIREMENTS
Sears rotary walk-behind power lawn mowers conform to the safety standards of the
American National Standards Institute and the U.S. Consumer Product Safety Commis-
sion. The blade turns when the engine is running,
Operator presence control bar- must be Primer - pumps additional fuel from the
held down to the handle to start the engine, carburetor to the cylinder for use when starting
Release to stop the engine° a cold engine.
Starter handle - used for starting the engine,
5
Theoperationofanylawn mower can
result in foreign objects thrown into the
eyes, which can result in severe eye
damage. Always wear safety glasses or
eye shields while operating your lawn
mower or performing any adjustments or
repairs. We recommend a wide vision
safety mask over the spectacles or
HOW TO USE YOUR LAWN MOWER
ENGINE SPEED
The engine speed was set at the factory
for optimum performance, Speed is not
adjustable.
ENGINE ZONE CONTROL
CAUTION; Federal regulations require an
engine control to be installed on this lawn
mower in order to minimize the risk of
blade contact injury. Do not under any
circumstances attempt to defeat the
function of the operator control° The blade
turns when the engine is running,
° Your lawn mower is equipped with an
operator presence control bar which
requires the operator to be positioned
behind the lawn mower handle to start
and operate the lawn mower.
TO ADJUST CUTTING HEIGHT
° Raise wheels for low cut and lower
wheels for high cut.
° Adjust cutting height to suit your
requirements. Medium position is best
for most lawns.
• To change cutting height, squeeze
adjuster lever toward wheel. Move
wheel up or down to suit your require-
ments. Be sure all wheels are in the
same setting.
NOTE: Adjuster is properly positioned
when plate tab inserts between tabs in
lever. Also, 9-position adjusters (if so
equipped) allow lever to be positioned
between the plate tabs.
Raise wheels for low cut _ Lever'
_ ___ _atetab!I
Lower wheels for
high cut
CAUTION: Do not run your lawn mower
without discharge guard, approved grass
catcher in place.
BEFORE STARTING ENGINE
OIL
Your lawn mower is shipped without oil in
the engine.
= Be sure mower is level and area around
oil fill is clean.
,, Remove engine oil plug and fill to the
top of slot in filler hole.
° Use 20 ozs. of oil. For type and grade
of oil to use, see "ENGINE" in Customer
Responsibilities section of this manual.
o Pour oil slowly. Do not over fill.
o Check oil level before each use. Add oil
if needed.
o Reinstall engine oil plug and tighten.
o Change the oil after every 25 hours of
operation or each season. You may
need to change the oil more often under
dusty, dirty conditions.
GAS
° Fill fuel tank. Use fresh, clean,
regular unleaded gasoline with a minimum
of 87 octane. Do not mix oil with gasoline.
Purchase fuel in quantities that can be
used within 30 days to assure fuel
freshness. Gasoline filler cap
Oil fillerplug
TO START ENGINE
o To start a cold engine, push primer five
(5) times before trying to start. Use a
firm push. This step is not usually
necessary when starting an engine
which has already run for a few minutes_
Hold operator presence control bar
down to the handle and pull starter
handle quickly. DO NOT allow starter
rope to snap back.
o To STOP engine, release operator
presence control bar.
6
NOTE:Incoolerweatherit may be o
necessary to repeat priming steps_ In
warmer weather over priming may cause
flooding and engine will not start. If you do o
flood engine wait a few minutes before
attempting to start and DO NOT repeat
priming steps,
MOWING TIPS
o Under certain conditions, such as very
tall grass, it may be necessary to raise
the height of cut to reduce pushing effort
and to keep from overloading the engine °
and leaving clumps of grass clippings.
• For extremely heavy cutting, reduce the
width of cut and raise the rear of the
lawn mower housing one (1) wheel
adjuster setting higher than the front for °
better discharge of grass.
For better grass bagging and most
cutting conditions, the engine speed
should be set in the fast position
For side discharge lawn mowers, cutting
in a counter-clockwise direction, starting
at the outside of the area to be cut,
spreads grass clippings more evenly
and puts less load on the engine. To
keep clippings off of walkways, flower
beds, etc. make the first cuts in a
clockwise direction
Pores in cloth grass catchers can
become filled with dirt and dust with use
and catchers will collect less grass. To
prevent this, regularly hose catcher off
with water and let dry before using,
Keep top of engine around starter clear
and clean of grass clippings and chaff,
This will help engine air flow and extend
engine life.
7
MAINTENANCE SCHEDULE
FlU- IN DATES
AS YOU COMPLETE
REGULAR SERVICE
Cheek for Loose Fasteners _
Clean/Inspect Grass Catcher
(if Equipped) _ _ ,
_VJ Clean Lawn Mower _ I
Clean Under Ddve Cover I
O (Power-Propelled Mowers)
Check drive beIVpulleys
RE Power-PropeUedMowels)
ChecldSharpen/Replace Blade _'
LubdcatJonChart _ _,#
Clean Battery/Recharc
....... Electric Start Mower_ .... _ _ _4
E Check Engine Oil Level _#'
N Change Engine Oil _1,_
G Clean Air Filter ft/
Inspect Muffler _/'
N Clean or Replace Spark Plug
I_ Replace Air Filter Paper Cartridge _,ds
1 _Change moro ohan when oporating_undor _ heavy Io_d ot _ high ambient tr_mperaturo_
2 ,.Se_lce more often when Qpemting tn d_tty or dusty condlt_ons
3 ,.Repl_co b_dos moro orlon when m_wins _n _an6y sos
4 - Charg_ 48 haur_ at end ol season
GENERAL RECOIVIMENDATIONS
The warranty on this lawn _ower does not
cover items that have been subjected to
operator abuse or negligence To receive
full value from the warranty, operator' must
maintain mower as instructed in this
manual.
Some adjustments will need tO be made
periodically to properly maintain your unit.
All adjustments in the Service and
Adjustments section of this manual should
be checked at least once,_ac.h season.
= Once a year, replace _e s'park plug,
clean or replace air filter element and
check blade for wear. A new spark plug
and clean/new air filter element assures
proper air-fuel mixture and helps your
engine run better and last longer.
o Follow the maintenance schedule in this
manual.
BEFORE EACH USE
= Check engine oil level
o Check for loose fasteners.
LUBRICATION
Keep unit well lubricated (See "LUBRICA-
TION CHART").
(_ Spray lubricant
(_ Referto CUSTOMER
IMPORTANT: Do not oil or grease plastic
wheel bearings. Viscous lubricants will
attract dust and dirt that will shorten the life
of the self-lubricating bearings. If you feel
they must be lubricated, use only a dry,
powered graphite type lubricant sparingly.
_ERVICE DATES
LUBRICATION CHART
(_ Wheel
adjuster (_) Engine oil
Brake
spring
(D Discharge bracket
guard
Handle bracket hinge pin
mountingpin
RESPONSIBILITIES "ENGINE" section
8
PRODUCT SPECUFICATUONS
MODEL NUMBER 917.387210
SERIAL NUMBER
DATE OF PURCHASE
HORSEPOWER: 4.0
DISPLACEMENT: 9O5CU IN.
GASOLINE CAPACITY/TYPE: 1.25 QUARTS
UNLEADED REGULAR
OIL TYPE (API-SF/SG/SH): SAE 30 (ABOVE 32°F)
SAE 5W-30 (BELOW 32°F)
OIL CAPACITY: 20 OZS.
SPARK PLUG(GAP: .030") CHAMPION J19LM
VALVECLEARANCE: INTAKE: .004 - .008
EXHAUST: .004- .008
SOLID STATE IGNITION
AIR GAP: ,0125 IN.
BLADE BOLT TORQUE: 35-40 FT. LBS.
o The model ahd serial numbers will be found on a decal attached to the rear of the
lawn mower housing.Record both serial number and date of purchase in space
provided above.
LAWN MOWER
Always observe safety rules when
performing any maintenance,
TIRES
o Keep tires free of gasoline, oil, or insect
control chemicals which can harm
rubber
o Avoid stumps, stones, deep ruts, sharp
objects and other hazards that may
cause tire damage
BLADE CARE
For best results, mower blade must be
kept sharp. Replace bent or damaged
blades.
TO REMOVE BLADE
o Disconnect spark plug wire from spark
plug and place wire where it cannot
come in contact with spark plug.
o Turn lawn mower on its side. Make sure
air filter and carburetor are up.
o Use a wood block between blade and
mower housing to prevent blade from
turning when removing blade bolt.
o Protect your hands with gloves and/or
wrap blade with heavy cloth.
o Remove blade bolt by turning counter-
clockwise Use a 9/16" box or open-end
wrench.
o Remove blade and attaching hardware
(bolt, lock washer and hardened
washer)
NOTE: Remove the blade adapter and
check the key inside hub of blade adapter
The key must be in good condition to work
properly. Replace adapter if damage&
TO REPLACE BLADE
• Position the blade adapter on the engine
crankshafL Be sure key in adapter and
crankshaft keyway are aligned.
o Position blade on the blade adapter
aligning the two (2) holes in the blade
with the raised lugs on the adapter.
o Be sure the trailing edge of blade
(opposite sharp edge) is up toward the
engine.
o Install the blade bolt with the lock
washer and hardened washer into blade
adapter and crankshaft.
o Use block of wood between blade and
lawn mower housing and tighten the
blade belt, turning clockwise.
° The recommended tightening torque is
35-40 ft. Ibs..
IMPORTANT: Blade bolt is grade 8
heat treated..
NOTE: We do not recommend sharp-
ening blade- butifyoudo, be sure the
blade is balanced.
TO SHARPEN BLADE
Care should be taken to keep the blade
balanced. An unbalanced blade will cause
eventual damage to lawn mower or
engine.
o The blade can be sharpened with a file
or on a grinding wheel. Do not attempt
to sharpen while on the mower.
o To check blade balance, drive a nail into
a beam or wall. Leave about one inch of
the straight nail exposed. Place center
hole of blade over the head of the nail
If blade is balanced, it should remain in
a horizontal position. If either end of the
blade moves downward, sharpen the
heavy end until the blade is balanced.
Blade Crankshaft
keyway
Key
Blade
Crank-
shaft
bolt
Lock Trai Blade
washer' edge adapter
Hardened
washer
GRASS CATCHER
(If purchased as an accesssory)
o The grass catcher may be hosed with
water, but must be dry when used,
= Check your grass catcher often for
damage or deterioration. Through
normal use it will wear. If catcher needs
replacing, replace only with a manufac-
turer approved replacement catcher.
Give the lawn mower model number
when ordering.
ENGINE
LUBRICATION
Use only high quality detergent oil rated with
API service classification SF, SG or SH.
Select the oil's SAE viscosity grade according
to your expected operating temperature.
SAE VIScosrPI" GRADES
NOTE: Although multi-viscosity oils (5W30,
10W30 etc.) improve starting in cold weather,
these multi-viscosity oils will result in increased
oil consumption when used above 32°F.
Check your engine oil level more frequently to
avoid possible engine damage from running
lowon oil.
Change the oil after every 25 hours of
operation or at least once a year if the lawn
mower is not used for 25 hours in one year.
Check the crankcase oil level before starting
the engine and after each five (5) hours of
continuous use. Tighten oil plug securely each
time you check the oil level
TO CHANGE ENGINE OIL
o Disconnect spark plug wire from spark plug
and place wire where it cannot come in
contact with spark plug..
o Be sure lawn mower is on level surface.
o Oil will drain more freely when warm.
= Catch oil in a suitable container
= Remove bottom oil drain plug.
• After oil has drained completely, replace oil
drain plug and tighten securely.
o Refill engine with oil. Pourslowiy. Do not
over fill.
• FlUto top of slot inside of filler hole
• Reconnect spark plug wire to spark plug.
Drain plug
AIR FILTER
Your engine willnot run properly and may be
damaged by using a dirty air filter. Clean the
element after every 25 hours of operation,
more often if mower is used in very dusty, dirty
conditions.
TO CLEAN AIR FILTER ELEMENT
o Remove the air filter by tuming counter-
clockwise to the stop and pull away from
collar.
10
o Removefilterfrominsideofcover.
o Cleantheinsideofthecoverandthecollar
toremoveanydirtaccumulation
o Insertnewfilterintocover
° Putairfiltercoverandfilterintocollar
aligningthetabwiththeslot
o Pushinoncoverandturnclockwiseto
tighten.
Collar
/ Clip \_ Tum
\ _2._'_.,._%-._"-%.counter-
C'o°Ce 2ise
MUFFLER
Inspect and replace corroded muffler as it
could create a fire hazard and/or damage.
SPARK PLUG
Change your spark plug each year to make
your engine start easier and run better. Set
spark plug gap at .030 inch.
CLEANING
IMPORTANT: FOR BEST PERFORMANCE,
KEEP MOWER HOUSING FREE OF BUILT-
UP GRASS AND TRASH. Clean the
underside of your mower after each use
CAUTION: Disconnect spark plug wire from
spark plug and place wire where itcannot
come in contact with the spark plug
. Turn lawn mower on its side Make sure air
filter and carburetor are up. Clean the
underside of your lawn mower by scraping
to remove build-up of grass and trash.
o Clean engine often to keep trash from
accumulating A clogged engine runs hotter
and shortens engine life
o Keep finished surfaces and wheels free of
all gasoline, oil,etc.
o We do not recommend using a garden
hose to clean lawn mower unless the
electrical system, muffler, air filter and
carburetor are covered to keep water out.
Water in engine can result in shortened
engine life.
CAUTION: BEFORE PERFORMING ANY
SERVICE OR ADJUSTMENTS:
o Release control ban
o Make sure the blade and all moving parts
have completely stopped
° Disconnect spark plug wire from spark plug
and place where it cannot come in contact
with plug.
LAWN MOWER
TO ADJUST CU-I-RNG HEIGHT
See "TO ADJUST CUTTING HEIGHT" in the
Operation section of this manual
REAR DEFLECTOR
The rear deflector, attached between the rear
wheels of your mower, is provided to minimize
the possibility that objects will be thrown out of
the rear of the mower into the operator
mowing position. If the deflector becomes
damaged, it should be replaced,
DISCHARGE GUARD
The discharge guard attached to the
discharge opening of your lawn mower, is
provided to prevent the possibility of injury
resulting from objects being thrown out of the
discharge opening into the operator mowing
position. Ifthe discharge guard becomes
damaged, it should be replaced,
TO ADJUST HANDLE
Your lawn mower handle can be raised or
lowered for your mowing comfort. Four (4)
positions are available: high, medium high,
medium low and low. Handles are shipped
mounted in the medium low position
o To change from medium low to medium
high position, the upper and lower handle
sections will have to be turned over.
o Remove the controls and operator presence
control bar from the upper handle.
o Remove the starter rope guide from the
lower handle.
o Remove hairpin cotters
o Disconnect the lower handle from the
handle bracket&
o Tum the handle over and reassemble the
hairpin cotters that have been removed,
o Reassemble the starter rope guide.
° Reassemble the controls and the operator
presence control bar to the upper handle.
CAUTION: The operator presence control bar
must pivot freely to permit blade brake
engagement when control bar is released. Do
net overtighten the fasteners holding the
controls to the upper handle.
11
o Tochangefrommediumlowtohigh
positiononlytheupperhandlesectionwill
havetobetumedover.
° Tochangefrommediumlowtolowposition,
onlythelowerhandlesectionwillhavetobe
tumedover_
Medium
Medium
low
High __ow
Lower handle
Mounting
bracket
Squeeze to
remove
Hairpin clip
ENGINE
CARBURETOR
Your carburetor has a non-adjustable fixed
main jet for mixture control. If your engine
does not operate properly due to suspected
carburetor problems, take your lawn mower to
an authorized service center for repair and
adjustment.
ENGINE SPEED
The engine speed has been factory seL Do
not attempt to increase engine speed as it
may result in personal injury. If you believe the
engine is running too fast or too slow, take
your lawn mower to an authorized service
center for repair and adjustment.
Immediately prepare your lawn mower for
storage at the end of the season or if the unit
will not be used for 30 days or more.
LAWN MOWER
When lawrl mower is to be storedfor a peded
of time, clean it thoroughly, remove all dirt,
grease, leaves, etc_ Store in a clean, dry area.
o Clean entire lawn mower (See "CLEAN-
ING" lt] the Customer Responsibilities
section of this manual)_
o Lubricate as shown in the Customer
Responsibilities section of this manual.
= Be sure that all nuts, bolts, screws, and pins
are securely fastened. Inspect moving
parts for damage, breakage and wear.
Replace if necessary.
= Touch up all rusted or chipped paint
surfaces; sand lightly before painting.
HANDLE
You carl fold your lawn mower handle for
storage.
,, Squeeze the bottom ends of the lower
handle toward each other until the lower
handle dears the handle bracket, then
move handle fonNard.
o Loosen upper handle mounting bolts
enough to allow upper handle to be folded
back.
IMPORTANT: When folding the handle for
storage or transportation, be sure to fold the
handle as shown or you may damage the
control cables.
° When setting up your handle from the
storage position, the lower' handle will
automatically lock irrto the mowing position.
Squeeze to fold
/f
Mounting pin
Hairpin cotter
Operator bar
Upper'handle
Lift up
Mowing
position
Lower
handle
12
ENGINE
FUEL SYSTEM
iMPORTANT: It is importantto prevent
gum deposits from forming in essential fuel
system parts such as carburetor, fuel filter,fuel
hose, or tank during storage Also, experience
indicates that alcohol blended fuels (called
gasohol or using ethanol or methanol) can
attract moisture which leads to separation and
formation of acids during storage. Acidic gas
can damage the fuel system of an engine
while in storage
o Drain the fuel tank.
o Start the engine and let itrun until the fuel
lines and carburetor are empty.
o Never use engine or carburetor cleaner
products in the fuel tank or permanent
damage may occur
,, Use fresh fuel next season
NOTE: Fuel stabilizer is an acceptable
alternative in minimizing the formation of fuel
gum deposits during storage. Add stabilizer to
gasoline in fuel tank or storage container,
Always follow the mix ratio found on stabilizer
container, Run engine at least 10 minutes
after adding stabilizer to allow the stabilizer to
reach the carburetor Do not drain the gas
tank and carburetor if using fuel stabilizer,
ENGINE OIL
Drain oil (with engine warm) and replace with
clean engine oil (See "ENGINE" in the
Customer Responsibilities section of this
manual).
CYLINDER
o Remove spark plug
Pour one ounce (29 ml) of oil through spark
plug hole into cylinder,
o Pull starter handle slowly a few times to
distribute oil
o Replace with new spark, plug.
OTHER
', Do not store gasoline from one season to
another.
,, Replace your gasoline can ifyour can starts
to rest, Rust and/or dirt in your gasoline will
cause problems
• tf possible, store your unit indoors and cover
it to give protection from dust and dirt.
o Cover your unit with a suitable protective
cover that does not retain moisture. Do not
use plastic Plastic cannot breathe which
allows condensation to form and will cause
your unit to rust.
IMPORTANT: Never cover mower while
engine and exhaust areas are still warm
CAUTION: Never store the lawn mower with
gasoline in the tank inside a building where
fumes may reach an open flame or spark.
Allow the engine to cool before storing inany
enclosure.
TROUBLESHOOTING CHART
PROBLEM
Doesnots_
CAUSE
o Dirty air fillet
o Out of fuel,
o Stale fuel
o Water in fuel,
o Spark plug wire is
discennected.
o Bad spark plug.
. Loose blade or broken blade
adapter,
o Control bar in released
position°
o Control bar defective.
CORRECTION
o Clean/replace airfiiter.
o Fillfuel tank.
o Drain tank and refill with
fresh clean fuel.
° Drain fuel tank and
carburetor and refill tank
with fresh gasoline.
o Connect wire to plug.
o Replace spark plug.
• Tighten blade bolt or
replace blade adapter.
= Depress control bar to
handle.
° Replace control bar.
13
TROUBLESHOOTING CHART
PROBLEM
Loss of power
3AUSE
o Rear of lawn mower housing
or cutting blade dragging
in heavy grass.
o Cutting too much grass,
o Dirty air filter.
= Buildup of grass, leaves,
and trash under mower:
o Too much oilin engine.
o Walking speed too fasL
Poorcut-uneven
= Worn, bent orloose blade,
• Wheel heights uneven_
= Low engine speed.
= BuUdupof grass, leaves
and trash under mower.
CORRECTION
o Set to"Higher Cur'
position,
o Set to"Higher Cut"
position.
o Clean/replace air filter:
= Clean underside of mower
housing.
= Check oil level
= Cut at slower walking
speed.
. Replace bladeo]ighten
blade bait,
= Set all wheels at same
height
° Set engine speed control
in fast position.
o Clean underside of
mower housing=
_cessive
/ibration
_tarter rope hard
:opull
m_
3ross catcher
tot filling (if so
.-=quipped)
-lard to push
= Worn, bent or loose blade.
= Bent engine crankshaft.
o Engine flywheel brake ison
when control bar is released.
= Bent engine crankshaft.
o Blade adapter broken.
o Blade dragging in grass.
° Cutting height too low.
• Lift on blade wom off.
° Catcher not venting air.
o Low engine speed_
o Grass is toohigh or wheel
height istoo low.
° Rear of lawn mower
housing or blade dragging
in grass.
o Grass catcher too full.
= Handle height position not
rightfor you°
o Replace blade.'l]ghten
blade boll
• Contact an authorized
service center:
= Depress control bar to
upper handle before
pulling starter rope_
o Contact an authorized
service center.
° Replace blade adapter,
= Move lawn mower to cut
grass or to hard surface
to start engine.
o Raise cutting height.
o Replace blade.
• Clean grass catcher.
o Set engine speed control
in fast position.
o Raise cutting height.
o Raise rear of lawn mower
housing one (1) setting
higher.
° Empty grass catcher.
o Adjust handle height to
suit.
14
Loading...