Craftsman 917378771 Owner’s Manual

Owner's Manual

ICRAFTSMAWI

ROTARY LAWN MOWER

7.0 Horsepower Power-Propelled

21" Rear Discharge

Model No.

917.378771

CAUTION:

Read and follow all Safety Rules and Instructions

before operating this equipment

Sears, Roebuck and Co., Hoffman Estates, IL 60179 U.S.A.

Visit our Craftsman website:www.sears.com/craftsman

Warranty ............................................... 2

Safety Rules ...................................... 2-4

Assembly / Pre-Operation .................... 5

Operation ........................................... 6-9

Maintenance Schedule ...................... 10

Maintenance ................................. 10-13

LIMITED TWO YEAR WARRANTY ON CRAFTSMAN POWER MOWER For two years from date of purchase, when this Craftsman Lawn Mower is maintained,

lubricated, and tuned up according to the operating and maintenance instructions in the owner's manual, Sears will repair free of charge any defect in material or workman-

ship.

If this Craftsman Lawn Mower is used for commercial or rental purposes, this warranty applies for only 90 days from the date of purchase.

This Warranty does not cover:

• Expendable items which become worn during normal use, such as rotary mower blades, blade adapters, belts, air cleaners and spark plug.

• Repairs necessary because of operator abuse or negligence, including bent crankshafts and the failure to maintain the equipment according to the instructions

contained in the owner's manual.

Product Specifications ........................ 11

Service and Adjustments .............. 13-15

Storage ......................................... 15-16

Troubleshooting ........................... 16-17

Repair Parts .................................. 35-43

Sears Service ...................... Back Cover

Warranty service is available by returning the Craftsman power mower to the nearest

Sears Service CentedDepartment in the United States. This warranty applies only

while this product is used in the United States.

This Warranty gives you specific legal rights, and you may also have other rights which

vary from state to state. Sears, Roebuck and Co., D/817 WA, Hoffman Estates, Illinois 60179

IMPORTANT: This cutting machine is capable of amputating hands and feet and

throwing objects. Failure to observe the following safety instructions could result in

serious injury or death. _,Look for this symbol to point out

important safety precautions. It means CAUTION!H BECOMEALERT!!! YOUR

SAFETY IS INVOLVED.

_], CAUTION: Always disconnect spark

plug wire and place wire where it cannot

contact spark plug in order to prevent

accidental starting when setting up,

transporting, adjusting or making repairs.

_WARNING: Engine exhaust, some of

its constituents, and certain vehicle

components contain or emit chemicals

known to the State of California to cause

cancer and birth defects or other repro- ductive harm.

Aq,WARNING" Battery posts, terminals and

related accessories contain lead and lead compounds, chemicals known to the

State of California to cause cancer and birth defects or other reproductive harm.

Wash hands after handling.

_, CAUTION: Muffler and other engine

parts become extremely hot during operation and remain hot after engine has stopped. To avoid severe burns on contact, stay away from these areas.

I.GENERAL OPERATION

• Read, understand, and follow all

instructions on the machine and in the manual(s) before starting. Be thor-

oughly familiar with the controls and the proper use of the machine before

starting.

• Do not put hands or feet near or under rotating parts. Keep clear of the

discharge opening at all times.

• Only allow responsible individuals, who are familiar with the instructions, to

operate the machine.

• Clear the area of objects such as

rocks, toys, wire, bones, sticks, etc.,

which could be picked up and thrown

by the blade.

• Be sure the area is clear of other

people before mowing. Stop machine if anyone enters the area.

• Do not operate the mower when barefoot or wearing open sandals. Always wear substantial foot wear.

• Do not pull mower backwards unless absolutely necessary. Always look

down and behind before and while moving backwards.

• Do not operate the mower without proper guards, plates, grass catcher or

other safety protective devices in place.

• See manufacturer's instructions for proper operation and installation of

accessories. Only use accessories approved by the manufacturer.

• Stop the blade(s) when crossing gravel drives, walks, or roads.

• Stop the engine (motor) whenever you leave the equipment, before cleaning

the mower or unclogging the chute.

• Shut the engine (motor) off and wait

until the blade comes to complete stop before removing grass catcher.

• Mow only in daylight or good artificial light.

• Do not operate the machine while under the influence of alcohol or drugs.

• Never operate machine in wet grass.

Always be sure of your footing: keep a firm hold on the handle and walk;

never run.

• Disengage the self-propelled mecha- nism or drive clutch on mowers so

equipped before starting the engine (motor).

• If the equipment should start to vibrate abnormally, stop the engine (motor)

and check immediately for the cause. Vibration is generally a warning of

trouble.

• Always wear safety goggles or safety glasses with side shields when

operating mower.

II. SLOPE OPERATION Slopes are a major factor related to slip

and fall accidents which can result in severe injury. All slopes require extra

caution. If you feel uneasy on a slope, do not mow it.

DO:

• Mow across the face of slopes: never up and down. Exercise extreme caution when changing direction on slopes.

• Remove obstacles such as rocks, tree limbs, etc.

• Watch for holes, ruts, or bumps. Tall grass can hide obstacles.

DO NOT:

• Do not trim near drop-offs, ditches or embankments. The operator could lose

footing or balance.

• Do not trim excessively steep slopes.

• Do not mow on wet grass. Reduced footing could cause slipping.

IIh CHILDREN

Tragic accidents can occur if the operator

is not alert to the presence of children. Children are often attracted to the

machine and the mowing activity. Never assume that children will remain where

you last saw them.

• Keep children out of the trimming area and under the watchful care of another

responsible adult.

• Be alert and turn machine off if children enter the area.

• Before and while walking backwards, look behind and down for small

children.

• Never allow children to operate the machine.

• Use extra care when approaching blind corners, shrubs, trees, or other objects

that may obscure vision.

IV. SERVICE

Use extra care in handling gasoline and other fuels. They are flammable

and vapors are explosive.

- Use only an approved container.

- Never remove gas cap or add fuel with the engine running. Allow

engine to cool before refueling. Do

not smoke.

-Never refuel the machine indoors.

- Never store the machine or fuel

container inside where there is an open flame, such as a water heater.

• Never run a machine inside a closed area.

• Never make adjustments or repairs with the engine (motor) running.

Disconnect the spark plug wire, and keep the wire away from the plug to

prevent accidental starting.

• Keep nuts and bolts, especially blade attachment bolts, tight and keep

equipment in good condition.

• Never tamper with safety devices. Check their proper operation regularly.

• Keep machine free of grass, leaves, or other debris build-up. Clean oil or fuel

spillage. Allow machine to cool before storing.

• Stop and inspect the equipment if you

strike an object. Repair, if necessary, before restarting.

• Never attempt to make wheel height

adjustments while the engine (motor) is running.

• Grass catcher components are subject

to wear, damage, and deterioration, which could expose moving parts or

allow objects to be thrown. Frequently check components and replace with

manufacturer's recommended parts,

when necessary.

• Mower blades are sharp and can cut. Wrap the blade(s) or wear gloves, and

use extra caution when servicing them.

• Do not change the engine governor setting or overspeed the engine.

These accessories were available when this lawn mower was produced. They are not shipped with your mower. They are also available at most Sears retail outlets and service centers. Most Sears stores can also order repair parts for you, when you provide the model

number of your lawn mower. Some of these accessories may not apply to your lawn mower.

LAWN MOWER PERFORMANCE

CLIPPING DEFLECTOR

FOR REAR DISCHARGE LAWN MOWERS

r \ GRASS CATCHERS

"\ REAR DISCHARGE

\ _ FOR

_\ LAWN MOWERS

LAWN MOWER MAINTENANCE

MUFFLERS

BELTS BLADES

MULCHER KITS

_-_') GRASS CATCHERS

_( SiDE DISCHARGE

BLADE ADAPTERS

i LAWN MOWERS

AIR FILTERS

FOR

WHEELS

STABILIZER

GAS CANS

SPARK PLUGS

ENGINE OIL

Read these instructions and this manual

in its entirety before you attempt to assemble or operate your new lawn

mower. IMPORTANT: This lawn mower is

shipped WITHOUT OIL OR GASOLINE in the engine.

Your new lawn mower has been as-

sembled at the factory with the exception of those parts left unassembled for

shipping purposes. All parts such as nuts, washers, bolts, etc., necessary to com-

plete the assembly have been placed in the parts bag. To ensure safe and proper

operation of your lawn mower, all parts and hardware you assemble must be tightened securely. Use the correct tools

as necessary to ensure proper tightness.

TO REMOVE LAWN MOWER FROM

CARTON

1. Remove loose parts included with mower.

2. Cut down two end corners of carton and lay end panel down flat.

3. Remove all packing materials except

padding between upper and lower handle and padding holding operator

presence control bar to upper handle.

4. Roll lawn mower out of carton and check carton thorougly for additional

loose parts.

HOW TO SET UP YOUR LAWN MOWER

TO UNFOLD HANDLE

IMPORTANT: Unfold handle carefully so as not to pinch or damage control cables.

1. Raise handles until lower handle section locks into place in mowing

position.

2. Remove protective padding, raise upper handle section into place on

lower handle and tighten both handle knobs.

3. Remove handle padding holding operator presence control bar to

upper handle.

Your lawn mower handle can be adjusted for your mowing comfort. Refer to "AD-

JUST HANDLE" in the Service and

Adjustments section of this manual.

Operator 1: control bar

Mowing

position

Lower handle

TO INSTALL A'CFACHMENTS

Your lawn mower was shipped ready to be used as a mulcher. To convert to

bagging, see "TO CONVERT MOWER" in the Operation section of this manual).

KNOW YOUR LAWN MOWER READ THIS OWNER'S MANUAL AND ALL SAFETY RULES BEFORE OPERATING

YOUR LAWN MOWER. Compare the illustrations with your lawn mower to familiarize yourself with the location of various controls and adjustments. Save this manual for

future reference.

These symbols may appear on your lawn mower or in literature supplied with the

product. Learn and understand their meaning.

CAUTION ENGINE ENGINE FAST SLOW CHOKE FUEL OIL DANGER, KEEP HANDS

OR WARNING ON OFF AND FEET AWAY

Operator presence control bar

Throttle

Drive control lever

Starter handle

Handle knob

Engine oil cap with dipstick

Grass catchel

Muffler

Housing

Gasoline filler cap

Air filteJ

Primer Nheel adjuster (on each wheel)

IMPORTANT: This lawn mower is shipped WITHOUT OIL OR GASOLINE in the engine.

MEETS CPSC SAFETY REQUIREMENTS Sears rotary walk-behind power lawn mowers conform to the safety standards of the

American National Standards Institute and the U.S. Consumer Product Safety Commis- sion. The blade turns when the engine is running.

Operator presence control bar - must be held down to the handle to start the

engine. Release to stop the engine. Starter handle - used for starting the

engine.

Primer- pumps additional fuel from the

Drive control lever - used to engage

power-propelled forward motion of lawn

mower. Throttle control - used for starting the engine and allows you to select either

FAST or SLOW engine speed.

carburetor to the cylinder for use when starting a cold engine.

Theoperationofanylawn

mowercan resultinforeign

objectsthrownintothe

eyes,whichcan resultin

severeeyedamage.

Alwayswearsafetyglassesoreye

shieldswhile operatingyour lawnmower or performinganyadjustmentsor repairs.

We recommendstandardsafetyglasses

or a wide vision safety mask worn over spectacles.

HOWTO USE YOUR LAWN MOWER ENGINE SPEED

The engine speed is controlled by a throttle control located on the side of the

upper handle. FAST position is for starting, normal cutting, trimming and

better grass bagging. SLOW position is for light cutting, trimming and fuel

economy.

SLOW

DRIVE CONTROL

• Self-propelling is controlled by holding the operator presence control bar down

to the handle and pushing the drive

control lever forward until it clicks; then releasing the lever.

• Forward motion will stop when the operator presence control bar is

released. To stop forward motion without stopping engine, release the

operator presence control bar slightly until the drive control disengages. Hold

operator presence control bar down against handle to continue mowing without self-propelling.

• To keep drive control engaged when turning comers, push down on handle

and lift front wheels off ground while turning lawn mower.

Operator presence control bar Drive

control

FAST

I Iii 11

ENGINE ZONE CONTROL ACAUTION: Federal regulations require

an engine control to be installed on this lawn mower in order to minimize the risk

of blade contact injury. Do not under any circumstances attempt to defeat the

function of the operator control. The blade turns when the engine is running.

• Your lawn mower is equipped with an

operator presence control bar which requires the operator to be positioned

behind the lawn mower handle to start and operate the lawn mower.

DRIVE

TO ENGAGE

DRIVE CONTROL

TO ADJUST CUTTING HEIGHT

Raise wheels for low cut and lower

wheels for high cut, adjust cutting height to suit your requirements. Medium

position is best for most lawns.

• To change cutting height, squeeze adjuster lever toward wheel. Move

wheel up or down to suit your require-

ments. Be sure all wheels are in the

same setting.

NOTE: Adjuster is properly positioned when plate tab inserts into hole in lever.

Also, 9-position adjusters (if so equipped) allow lever to be positioned between the

plate tabs.

LOWER WHEELS FOR HIGH CUT

Plate tab ~

RAISE WHEELS FOR LOW CUT Lever

CONTROL

DISENGAGED

TO CONVERT MOWER Your lawn mower was shipped ready to be

usedas a mulcher. Toconvertto bagging:

• Liftrear door of the lawn mower and place the grasscatcherframe hooksontothe

door pivotpins.

• To convertto mulchingoperation,remove grass catcher and close rear door.

A_CAUTION: Do not run your lawn mower without rear door closed, clipping deflector or approved grass catcher in place. Never attempt to operate the lawn

mower with the rear door removed or propped open.

Pivot pins Rear Grass

catcher

handle

Catcherframe

TO EMPTY GRASS CATCHER

1. Lift up on grass catcher using the

frame handle.

2. Remove grass catcher with clippings

from under lawn mower handle.

3. Empty clippings from bag using both frame handle and bag handle.

NOTE: Do not drag the bag when

emptying; itwill cause unnecessary wear.

Grass

catcher

frame

handle

Bag

handle

2. Remove oil dipstick from oil fill spout.

Make sure that rim ofspout is clean.

3. You receive a container of oil with the unit. Slowly pour 3/4 (15 oz.) of the oil

from the container down the oil fill spout into the engine.

4. Wait one minute to allow oil to settle. Insert and tighten dipstick, then

remove itto check oil level.

5. Continue adding small amounts of oil and rechecking the dipstick until it

reads full. DO NOT overfill, or engine

will smoke on startup.

6. Always be sure to retighten oil dipstick before starting engine.

• Check oil level before each use. Add oil if needed. Fill to full line on dipstick.

• Change the oil after every 25 hours of operation or each season. You may need to change the oil more often under dusty, dirty conditions.

ADD GASOLINE

• Fill fuel tank to bottom oftank filler neck. Do not overfill. Use fresh, clean,

regular unleaded gasoline with a minimum of 87 octane. Do not mix oil

with gasoline. Purchase fuel in quantities that can be used within 30

_1days to assure fuel freshness.

CAUTION: Wipe off any spilled oil or

fuel. Do not store, spill or use gasoline near an open flame. _, CAUTION: Alcohol blended fuels

(called gasohol or using ethanol or methanol) can attract moisture which

leads to separation and formation of acids during storage. Acidic gas can

damage the fuel system of an engine

while in storage. To avoid engine

problems, the fuel system should be emptied before storage of 30 days or longer. Drain the gas tank, start the

engine and let it run until the fuel lines

and carburetor are empty. Use fresh fuel

next season. See Storage Instructions for additional information. Never use engine or carburetor cleaner products in the fuel

tank or permanent damage may occur.

BEFORE STARTING ENGINE

ADD OIL Your lawnmower is shipped without oil in

the engine. For type and grade of oil to

use, see "ENGINE" in the Maintenance

section of this manual. A CAUTION: DO NOT overfill engine with

oil, or it will smoke on startup.

1. Be sure lawnmower is level and area

around oil fill is clean.

Engine

oil cap

olinefiller

cap

TOSTART ENGINE NOTE:Dueto protectivecoatingsonthe

engine,a smallamountofsmokemaybe presentduringthe initialuseofthe

productand should be considered

normal.

1. To start a cold engine, push primer three (3) times before trying to start.

Use a firm push. This step is not

usually necessary when starting an

engine which has already run for a few minutes.

2. Move throttle control lever to FAST

position.

3. Hold operator presence control bar

down to the handle and pull starter handle quickly. Do not allow starter

rope to snap back.

TO STOP ENGINE

• To stop engine, release operator

presence control bar.

NOTE: In cooler weather it may be necessary to repeat priming steps. In

warmer weather over priming may cause flooding and engine will not start. If you

do flood engine, wait a few minutes before attempting to start and do not

repeat priming steps.

MOWING TIPS

• Under certain conditions, such as very tall grass, it may be necessary to raise

the height of cut to reduce pushing effort and to keep from overloading the

engine and leaving clumps of grass clippings. It may also be necessary to

reduce ground speed and/or run the mower over the area a second time.

• For extremely heavy cutting, reduce the width of cut by overlapping

previously cut path and mow slowly.

• For better grass bagging and most

cutting conditions, the engine speed should be set in the FAST position.

• Pores in cloth grass catchers can

become filled with dirt and dust with use and catchers will collect less

grass. To prevent this, regularly hose catcher off with water and let dry

before using.

• Keep top of engine around starter

clear and clean of grass clippings and chaff. This will help engine air flow and

extend engine life.

MULCHING MOWING TIPS

IMPORTANT: For best performance, keep mower housing free of built-up

grass and trash. See "CLEANING" in the

Maintenance section of this manual.

• The special mulching blade will recut the grass clippings many times and

reduce them in size so that as they fall onto the lawn they will disperse into the grass and not be noticed. Also, the

mulched grass will biodegrade quickly to provide nutrients for the lawn.

Always mulch with your highest engine (blade) speed as this will provide the

best recutting action of the blades.

• Avoid cutting your lawn when it is wet. Wet grass tends to form clumps and

interferes with the mulching action. The best time to mow your lawn is the early

afternoon. At this time the grass has dried and the newly cut area will not be

exposed to the direct sun.

• For best results, adjust the lawn mower

cutting height so that the lawn mower cuts off only the top one-third of the grass blades. If the lawn is overgrown it

will be necessary to raise the height of cut to reduce pushing effort and to keep

from overloading the engine and leaving clumps of mulched grass. For

extremely heavy grass, reduce your width of cut by overlapping previously

cut path and mow slowly.

' MAX 1/3

• Certain types of grass and grass conditions may require that an area be

mulched a second time to completely hide the clippings. When doing a

second cut, mow across or perpendicu-

lar to the first cut path.

• Change your cutting pattern from week to week. Mow north to south one week

then change to east to west the next week. This will help prevent matting

and graining of the lawn.

MAINTENANCE SCHEDULE /__0_,_o__

FIL'I.OATES

AS YOU COMPLETE 7__'_O_ f SERVICE

REGULAR SERVICE /__"_:_'F'_.,,._F_ r DATES

Check for Loose Fasteners _ t,/

I Clean/Inspect Grass Catcher

(IfEquipped)

M Clean Lawn Mower i Ik/

wO Clean Under Ddve CoverIPower-Propelled Mowers)

Check drivebelt/pulleys

RE (Power-Propelled Mowers)

Check/Sharpen/Replace Blade

LubdcatlenChart

Clean Battery/Recharge IElectdc Start Mowers/

E Check Engine Oil Level

a Chan_le Engine Oil

G Clean Air Filter

InspectMuffler

v' v',

v% V=

N Clean or Replace Spark Plug E Replace Air Filter Paper Cartridge

1 - Change more often when opetaitng under a heavy load or in high ambient temperatures. 2 - Service mote often when operating in dirty or dusty conditions.

3 - Replace blades more often when mowing in sandy soil. 4 - Cha_ge 48 hours at end of season.

GENERAL RECOMMENDATIONS

The warranty on this lawn mower does

not cover items that have been subjected

to operator abuse or negligence. To

receive full value from the warranty,

operator must maintain mower as instructed in this manual. Some adjust-

ments will need to be made periodically to properly maintain your unit.

All adjustments in the Service and Adjustments section of this manual

should be checked at least once each season.

• Once a year, replace the spark plug, clean or replace air filter element and

check blade for wear. A new spark plug and clean/new air filter element

assure proper air-fuel mixture and help your engine run better and last longer.

• Follow the maintenance schedule in this manual.

(_) Spray lubricant

BEFORE EACH USE

(_) See "ENGINE" In Maintenance section.

1. Check engine oil level.

2. Check for loose fasteners.

IMPORTANT: Do not oil or grease plastic wheel bearings. Viscous

lubricants will attract dust and dirt that

LUBRICATION Keep unit well lubricated (See "LUBRI-

CATION CHART").

will shorten the life of the self-lubricat-

ing bearings. Ifyou feel they must be lubricated, use only a dry, powdered

graphite type lubricant sparingly.

LUBRICATION CHART

adjuster (on

each wheel)

oil

Rear door

hinge

(_) Handle bracket mounting pins

PRODUCT SPECIFICATIONS

Serial Number: Date of Purchase:

Gasoline Capacity / Type: 1.6 Quarts (Unleaded Regular)

Oil Type (API-SF-SJ): SAE 30 (above 32°F); SAE 5W-30 (below 32°F)

Oil Capacity: 20 Ounces Spark Plug (Gap: .020") Champion RC12YC Blade Bolt Torque: 35-40 ft. ibs.

The model and serial numbers will be found on a decal on the rear of the mower

housing. Record both serial number and date of purchase in space provided above

LAWN MOWER Always observe safety rules when perform-

ing any maintenance.

TIRES

• Keep tires free of gasoline, oil, or insect control chemicals which can harm rubber.

• Avoid stumps, stones, deep ruts, sharp objects and other hazards that may cause

tire damage.

BLADE CARE

For best results, mower blade must be

kept sharp. Replace bent or damaged blades.

TO REMOVE BLADE

1. Disconnect spark plug wire from spark plug and place wire where it cannot

come in contact with spark plug.

2. Turn lawn mower on its side. Make sure air filter and carburetor are up.

3. Use a wood block between blade and mower housing to prevent blade from

turning when removing blade bolt.

NOTE: Protect your hands with gloves and/or wrap blade with heavy cloth.

4. Remove blade bolt by turning counter- clockwise.

5. Remove blade and attaching hard- ware (bolt, lock washer and hardened

washer).

NOTE: Remove the blade adapter and check the key inside hub of blade

adapter. The key must be in good condi- tion to work properly. Replace adapter if

damaged. TO REPLACE BLADE

1. Position the blade adapter on the engine crankshaft. Be sure key in

adapter and crankshaft keyway are aligned.

2. Position blade on the blade adapter aligning the two (2) holes in the blade

with the raised lugs on the adapter.

3. Be sure the trailing edge of blade

(opposite sharp edge) is up toward

the engine.

4. Install the blade bolt with the lock washer and hardened washer into

blade adapter and crankshaft.

5. Use block of wood between blade and

lawn mower housing and tighten the blade bolt, tuming clockwise.

• The recommended tightening torque is

35-40 ft. Ibs.

IMPORTANT: Blade bolt is grade 8 heat

treated. TO SHARPEN BLADE

NOTE: We do not recommend sharpen- ing blade - but if you do, be sure the

blade is balanced. Care should be taken to keep the blade

balanced. An unbalanced blade will cause eventual damage to lawn mower

or engine.

• The blade can be sharpened with a file or on a grinding wheel. Do not attempt

to sharpen while on the mower.

• To check blade balance, drive a nail into a beam or wall. Leave about one

inch of the straight nail exposed. Place center hole of blade over the head of

the nail. If blade is balanced, it should

remain in a horizontal position. If either

end of the blade moves downward, sharpen the heavy end until the blade

is balanced.

Blade adaptel Crankshaft

Blade

Blade bolt Hard

washer Trailing edge Blade adapter

shaft

GRASS CATCHER

• The grass catcher may be hosed with

water, but must be dry when used.

• Check your grass catcher often for

damage or deterioration. Through

normal use it will wear. If catcher needs replacing, replace only with a manufac-

turer approved replacement catcher.

Give the lawn mower model number when ordering.

DRIVE WHEELS

Check front drive wheels each time before you mow to be sure they move

freely. The wheels not turning freely means

trash, grass cuttings, etc. are in the drive

wheel area and must be cleaned to free

drive wheels. If necessary to clean the drive wheels, be

sure to clean both front wheels.

1. Remove hubcaps, hairpin cotters and washers.

2. Remove wheels from wheel adjusters.

3. Remove any trash or grass cuttings

from inside the dust cover, pinion and/ or drive wheel gear teeth.

4. Put wheels back in place. NOTE: If after cleaning, the drive wheels

do not turn freely, contact a Sears or other qualified service center.

GEAR CASE

• To keep your drive system working properly, the gear case and area

around the drive should be kept clean and free of trash build-up. Clean under

the drive cover twice a season.

• The gear case is filled with lubricant to the proper level at the factory. The only

time the lubricant needs attention is if

service has been performed on the gear case.

• If lubricant is required, use only Elf brand oil, Part No. REDUCTELF 100.

Do not substitute.

SAE VISCOSITY GRADES

F , ÷20 0 30 32 40 60 80 100 ,

.3o -_o -1o o _'o _o 3o ,o

TEMPERATURE RANGE AWrlCIPATED BEFORE NEXT OIL CHANGE

NOTE: Although multi-viscosity oils

(5W30, 10W30 etc.) improve starting in cold weather, these multi-viscosity oils

will result in increased oil consumption

when used above 32°F. Check your engine oil level more frequently to avoid

possible engine damage from running low on oil.

Change the oil after every 25 hours of operation or at least once a year if the

lawn mower is not used for 25 hours in one year.

Check the crankcase oil level before starting the engine and after each five (5)

hours of continuous use. Tighten oil plug

securely each time you check the oil

level.

TO CHANGE ENGINE OIL

NOTE: Before tipping lawn mower to

drain oil, drain fuel tank by running

engine until fuel tank is empty.

1. Disconnect spark plug wire from spark plug and place wire where it cannot

come in contact with spark plug.

2. Remove engine oil cap; lay aside on a clean surface.

3. Tip lawn mower on its side as shown and drain oil into a suitable container.

Rock lawn mower back and forth to remove any oil trapped inside of

engine.

4. Wipe off any spilled oil from lawn

mower or side of engine.

5. Fill engine with oil. (See "ADD OIL" in the Operation section of this manual).

6. Reconnect spark plug wire to spark

plug.

ENGINE

LUBRICATION Use only high quality detergent oil rated

with API service classification SF-SJ. Select the oirs SAE viscosity grade

according to your expected operating temperature.

Container _" .......

AIR FILTER

Your engine will not run properly using a dirty air filter. Clean the foam pre-cleaner

after every 25 hours of operation or every season. Replace paper cartridge every

100 hours of operation or every season,

whichever occurs first. Service air cleaner more often under dusty condi-

tions.

1. Loosen screws and remove cover.

2. Carefully remove cartridge.

3. Clean by gently tapping on a flat

surface. If very dirty, replace cartridge.

ACAUTION: Petroleum solvents, such as kerosene, are not to be used to clean

cartridge. They may cause deterioration of the cartridge. Do not oil cartridge. Do not

use pressurized air to clean or dry

cartridge.

4. Install cartridge, then replace cover.

)ver

,Base

MUFFLER

Inspect and replace corroded muffler as it

could create a fire hazard and/or dam- age.

SPARK PLUG Replace spark plugs at the beginning of

each mowing season or after every 100 hours of operation, whichever occurs first.

Spark plug type and gap setting are shown in "PRODUCT SPECIFICATIONS"

in Maintenance section of this manual.

CLEANING

IMPORTANT: For best performance, keep mower housing free of built-up grass and trash. Clean the underside of

your mower after each use.

_I_CAUTION: Disconnect spark plug wire from spark plug and place wire where it

cannot come in contact with the spark plug.

• Clean the underside of your lawn

mower by scraping to remove build-up of grass and trash.

• Clean engine often to keep trash from accumulating. A clogged engine runs

hotter and shortens engine life.

• Keep finished surfaces and wheels free

of all gasoline, oil, etc.

• We do not recommend using a garden

hose to clean lawn mower unless the electrical system, muffler, air filter and

carburetor are covered to keep water

out. Water in engine can result in shortened engine life.

CLEAN UNDER DRIVE COVER Clean under drive cover at least twice a season. Scrape underside of cover with

putty knife or similar tool to remove any build-up of trash or grass on underside of drive cover.

_WARNING: To avoid serious injury,

before performing any service or adjust- ments:

1. Release control bar and stop engine.

2. Make sure the blade and all moving parts have completely stopped.

3. Disconnect spark plug wire from spark plug and place where it cannot come

in contact with plug.

LAWN MOWER

TO ADJUST CUTTING HEIGHT See "TO ADJUST CUTTING HEIGHT' in

the Operation section of this manual.

REAR DEFLECTOR

The rear deflector, attached between the

rear wheels of your mower, is provided to

minimize the possibility that objects will be thrown out of the rear of the mower

into the operator's mowing position. If the

deflector becomes damaged, it should be

replaced.

TO REMOVE DRIVE BELT

1. Remove drive cover. Remove belt

from gearcase pulley by pushing down on pulley and rolling belt off it.

2. Turn lawn mower on its side with air filter and carburetor up.

3. Remove blade.

4. Remove debris shield.

5. Remove belt from engine pulley on

crankshaft.

TO REPLACE DRIVE BELT

1. Install new belt on engine pulley.

2. Reinstall debris shield and blade.

3. Return mower to upright position.

4. Install new belt on gearcase pulley.

5. Reinstall drive cover. NOTE: Always use factory approved belt

to assure fit and long life.

Lower

ROTATE

Mowing position

Hairpin

Drive

cover Belt

PUSH

TO ADJUST HANDLE

The handle can be mounted in a high or low position. The mounting holes in the

bottom of lower handle are off center for raising or lowering the handle.

!. Remove upper handle and all parts

attached to lower handle.

2. Remove hairpin cotters from lower handle bracket mounting pin.

3. Squeeze lower handle in to remove it from mounting pins.

4. Turn lower handle over to raise or lower handle.

5. Squeeze lower handle in and position holes onto mounting pins on handle

bracket.

6. Reassemble upper handle and all parts removed from lower handle.

Mounting: pin

LOW POSITION

TO ASSEMBLE GRASS CATCHER

1. Put grass catcher frame into grass bag with rigid part of bag on the bottom.

Make sure the frame handle is outside of the bag top.

2. Slip vinyl bindings over frame.

NOTE: If vinyl bindings are too stiff, hold them in warm water for a few minutes. If

bag gets wet, let it dry before using. ACAUTION: Do not run your lawn

mower without clipping deflector or approved grass catcher in place. Never attempt to operate the lawn mower with

the rear door removed or propped open.

Catcher frame

handle

Frame

opening

+ 30 hidden pages

Craftsman 917378771 Owner’s Manual

Specifications and Main Features

Frequently Asked Questions

User Manual