Craftsman 917378212 Owner’s Manual

Owner's Manual

JCRRFTSMRWI

5.5 HORSEPOWER 21" MULTI-CUT

POWER PROPELLED

ROTARY LAWNMOWER

Model No.

917.378212

• Safety

• Assembly

• Operation

• Maintenance

• EspaSol

• Repair Parts

CAUTION: Read and follow all

Safety Rules and Instructions beforeoperatingthisequipment

Sears, Roebuck and Co., Hoffman Estates, IL 60179

Visit our Craftsman website: www.sears.com/craftsman

Warranty ................................................. 2

Safety Rules ........................................ 2-4

Assembly ................................................ 5

Operation ........................................... 6-10

Maintenance Schedule ........................ 11

Maintenance .................................... 11-15

LIMITED TWO YEAR WARRANTY ON CRAFTSMAN POWER MOWER For two years from date of purchase, when this Craftsman Lawn Mower is maintained,

lubricated, and tuned up according to the operating and maintenance instructions in

the owner's manual, Sears will repair free of charge any defect in material or workman-

ship.

Product Specifications .......................... 12

Service and Adjustments ................. 14-15

Storage ............................................ 15-16

Troubleshooting .............................. 16-17

Repair Parts .......................................... 37

Parts Ordering ........................ Back Cover

Ifthis Craftsman Lawn Mower is used for commemial or rental purposes, this warranty

applies for only 90 days from the date of purchase.

This Warranty does not cover:

• Expendable items which become worn during normal use, such as rotary mower blades, blade adapters, belts, air cleaners and spark plug.

• Repairs necessary because of operator abuse or negligence, including bent crankshafts and the failure to maintain the equipment according to the instructions

contained in the owner's manual.

Warranty service is available by returning the Craftsman power mower to the nearest

Sears Service Center/Department in the United States. This warranty applies only

while this product is in use in the United States.

This Warranty gives you specific legal rights, and you may also have other rights which vary from state to state.

Sears, Roebuck and Co., D/817 WA, Hoffman Estates, Illinois 60179

IMPORTANT: This cutting machine is capable of amputating hands and feet and throwing objects. Failure to observe the following safety instructions could result in

serious injury or death.

I. GENERAL OPERATION

• Read, understand, and follow all

instructions on the machine and in the manual(s) before starting. Be thor-

oughly familiar with the controls and the proper use of the machine before starting.

• Do not put hands or feet near or under

rotating parts. Keep clear of the

discharge opening at all times.

• Only allow responsible individuals, who are familiar with the instructions, to

operate the machine.

• Clear the area of objects such as

rocks, toys, wire, bones, sticks, etc.,

which could be picked up and thrown by the blade.

• Be sure the area is clear of other people before mowing. Stop machine if

anyone enters the area.

• Do not operate the mower when barefoot or wearing open sandals.

Always wear substantial foot wear.

• Do not pull mower backwards unless absolutely necessary. Always look

down and behind before and while moving backwards.

• Do not operate the mower without proper guards, plates, grass catcher or other safety protective devices in place.

• See manufacturer's instructions for

proper operation and installation of

accessories. Only use accessories approved by the manufacturer.

• Stop the blade(s) when crossing gravel ddves, walks, or roads.

• Stop the engine (motor) whenever you

leave the equipment, before cleaning

the mower or unclogging the chute.

• Shut the engine (motor) off and wait

untilthe blade comes to complete stop before removing grass catcher.

• Mow only in daylight or good artificial

light.

• Do not operate the machine while under the influence of atcohot or drugs.

• Never operate machine in wet grass.

Always be sure of your footing: keep a firm hold on the handle and walk; never

run.

• Disengage the self-propelled mecha- nism or drive dutch on mowers so

equipped before starting the engine (motor).

• If the equipment should start to vibrate abnormally, stop the engine (motor) and check immediately for the cause. Vibration is generally a warning of

trouble.

• Always wear safety goggles or safety glasses with side shields when

operating mower.

I1.SLOPE OPERATION Slopes are a major factor related to slip

and fall accidents which can result in

severe injury. All slopes require extra caution. If you feel uneasy on a slope, do

not mow it.

DO"

• Mow across the face of slopes: never up and down. Exercise extreme caution

when changing direction on slopes.

• Remove obstacles such as rocks, tree limbs, etc.

• Watch for holes, ruts, or bumps. Tall grass can hide obstacles.

DO NOT:

• Do not trim near drop-offs, ditches or embankments. The operator could lose

footing or balance.

• Do not trim excessively steep slopes.

• Do not mow on wet grass. Reduced footing could cause slipping.

II1.CHILDREN Tragic accidents can occur if the operator

is not alert to the presence of children. Children are often attracted to the

machine and the mowing activity. Never assume that children will remain where

you last saw them.

• Keep children out of the trimming area

and under the watchful care of another responsible adult.

• Be alert and turn machine off if children enter the area.

• Before and while walking backwards,

look behind and down for small children.

• Never allow children to operate the

machine.

• Use extra care when approaching blind

corners, shrubs, trees, or other objects

that may obscure vision.

IV. SERVICE

• Use extra care in handling gasoline and other fuels. They are flammable and vapors are explosive.

-Use only an approved container.

-Never remove gas cap or add fuel with the engine running. Allow

engine to cool before refueling. Do not smoke.

-Never refuel the machine indoors.

- Never store the machine or fuel

container inside where there is an open flame, such as a water heater.

• Never run a machine inside a closed

area.

• Never make adjustments or repairs with the engine (motor) running. Disconnect

the spark plug wire, and keep the wire

away from the plug to prevent acciden-

tal starting.

• Keep nuts and bolts, especially blade attachment bolts, tight and keep equipment in good condition.

• Never tamper with safety devices. Check their proper operation regularly.

• Keep machine free of grass, leaves, or other debris build-up. Clean oil or fuel

spillage. Allow machine to cool before storing.

• Stop and inspect the equipment if you strike an object. Repair, if necessary, before restarting.

• Never attempt to make wheel height adjustments while the engine (motor) is

running.

• Grass catcher components are subject to wear, damage, and deterioration,

which could expose moving parts or

allow objects to be thrown. Frequently check components and replace with

manufacturer's recommended parts,

when necessary.

• Mower blades are sharp and can cut.

Wrap the blade(s) or wear gloves, and use extra caution when servicing them.

• Do not change the engine governor setting or overspeed the engine.

•,Look for this symbol to point out important safety precautions. It means

CAUTION!U BECOMEALERTH! YOUR SAFETY IS INVOLVED.

_,WARNING: Battery posts, terminals and

related accessories contain lead and lead

compounds, chemicals known to the State of California to cause cancer and birth

defects or other reproductive harm. Wash

• i, CAUTION: In order to prevent

hands after handling.

accidental starting when setting up,

transporting, adjusting or making repairs,

always disconnect spark plug wire and place wire where it cannot contact spark plug.

A CAUTION: Muffler and other engine

parts become extremely hot during

operation and remain hot after engine has

stopped. To avoid severe burns on contact, stay away from these areas.

_I,WARNING: Engine exhaust, some of its

constituents, and certain vehicle components contain or emit chemicals

known to the State of California to cause cancer and birth defects or other

reproductive harm.

These accessories were available when this lawn mower was produced. They are not shipped with your mower. They are also available at most Sears retail outlets and

service centers. Most Sears stores can also order repair parts for you, when you provide the model number of your lawn mower. Some of these accessories may not apply to your lawn mower.

LAWN MOWER PERFORMANCE

CLIPPING DEFLECTOR

FOR REAR DISCHARGE LAWN MOWERS

GRASS CATCHERS

FOR

REAR DISCHARGE

LAWN MOWERS

LAWN MOWER MAINTENANCE

MUFFLERS AIR FILTERS SPARK PLUGS

MULCHER KITS

_/t GRASS CATCHERS

_I SIDE DISCHARGE

FOR

LAWNMOWERS

STABILIZER

GAS CANS

BELTS BLADES BLADE ADAPTERS WHEELS ENGINE OIL

Read these instructions and this manual

in its entirety before you attempt to

assemble or operate your new lawn

mower. IMPORTANT: This lawn mower is

shipped WITHOUT OIL OR GASOLINE in the engine.

Your new lawn mower has been as- sembled at the factory with the exception

of those parts left unassembled for shipping purposes. All parts such as nuts,

washers, bolts, etc., necessary to com-

plete the assembly have been placed in

the parts bag. To ensure safe and proper

operation of your lawn mower, all parts

and hardware you assemble must be

tightened securely. Use the correct tools

as necessary to ensure proper tightness.

TO REMOVE LAWN MOWER FROM

CARTON

1. Remove loose parts included with mower.

2. Cut down two end corners of carton and lay end panel down flat.

3. Remove all packing materials except padding between upper and lower handle and padding holding operator presence control bar to upper handle.

4. Roll lawn mower out of carton and check carton thorougly for additional

loose parts.

HOWTO SET UPYOUR LAWN MOWER

TO UNFOLD HANDLE

IMPORTANT: Unfold handle carefully so

as not to pinch or damage control cables.

1. Raise handles until lower handle section locks into place in mowing

position.

2. Remove protective padding, raise upper handle section into place on lower handle and tighten both handle

knobs.

3. Remove handle padding holding

operator presence control bar to upper handle.

Your lawn mower handle can be adjusted

for your mowing comfort. Refer to "AD- JUST HANDLE" in the Service and

Adjustments section of this manual.

Operator

control bar

Mowing position

Lower handle

TO INSTALL A'I-FACHMENTS

Your lawn mower was shipped ready to be used as a mulcher. To convert mower

to bagging or discharging, see "TO

CONVERT MOWER" in the Operation section of this manual.

KNOWYOUR LAWN MOWER READ THIS OWNER'S MANUAL AND SAFETY RULES BEFORE OPERATING YOUR

LAWN MOWER. Compare the illustrations with your lawn mower to familiarize yourself with the location of various controls and adjustments. Save this manual for future

reference. These symbols may appear on your lawn mower or in literature supplied with the

product. Learn and understand their meaning.

CAUTION ENGINE ENGINE FAST SLOW CHOKE FUEL OIL DANGER, KEEP HANDS

OR WARNING ON OFF AND FEET AWAY

Throttle/choke

Operator presence control bar

control

Drive control lever

Starter

Engine zone control cable

Handle knob

Gasoline filler cap

Grass catcher Air filter

Fuel valve lever

Muffh

Engine oil cap

Housing

Drive

Mutcher door

IMPORTANT: This lawn mower is shipped WITHOUT OIL OR GASOLINE in the engine.

Wheel adjuster

(on each wheel)

MEETS CPSC SAFETY REQUIREMENTS

Sears rotary walk-behind power lawn mowers conform to the safety standards of the American National Standards Institute and the U.S. Consumer Product Safety Commis-

sion, The blade turns when the engine is running. Operator presence control bar - must

be held down to the handle to start the engine. Release to stop the engine.

Mulcher door - allows conversion to discharging or bagging operation.

Starter handle - used for starting the

engine.

Throttle choke/control lever - used for

starting the engine; & allows you to select

either CHOKE, FAST or SLOW engine speed.

Drive control lever - used to engage power-propelled forward motion of lawn

6 mower.

The operation of any lawn

mower can result in foreign objects thrown into the

eyes, which can result in

severe eye damage.

Always wear safety glasses or eye shields while operating your lawn mower or performing any adjustments or repairs.

We recommend a wide vision safety

mask over spectacles or standard safety glasses.

HOWTO USE YOUR LAWN MOWER ENGINE SPEED

The engine speed is controlled by a throttle control located on the side of the

upper handle. CHOKE position is for

starting a cold engine and FAST position

isfor normal cutting, trimming, and better

grass bagging. SLOW position is for light cutting, trimming and fuel economy.

SLOW

DRIVE CONTROL

• Self-propelling is controlled by holding

the operator presence control bar down

to the handle and pushing the drive

control lever forward until it clicks; then releasing the lever.

• Forward motion will stop when the

operator presence control bar is released. To stop forward motion

without stopping engine, release the

operator presence control bar slightly until the drive control disengages. Hold

operator presence control bar down against handle to continue mowing

without self-propelling.

• To keep drive control engaged when

turning corners, push down on handle

and lift front wheels off ground while

turning lawn mower.

ence control bar Drive

control

ENGINE ZONE CONTROL

_CAUTION: Federal regulations require an engine control to be installed on this lawn mower in order to minimize the risk

of blade contact injury. Do not under any circumstances attempt to defeat the

function of the operator control. The blade turns when the engine is running.

• Your lawn mower is equipped with an operator presence control bar which

requires the operator to be positioned behind the lawn mower handle to start

and operate the lawn mower.

_TO ENGAGE

TO ADJUST CUTTING HEIGHT

Raise wheels for low cut and lower

wheels for high cut, adjust cutting height to suit your requirements. Medium

position is best for most lawns.

• To change cutting height, squeeze

adjuster lever toward wheel. Move

wheel up or down to suit your require-

ments. Be sure all wheels are in the

same setting.

NOTE: Adjuster is properly positioned when plate tab inserts into hole in lever.

Also, 9-position adjusters (if so equipped) allow lever to be positioned between the

plate tabs. LOWER WHEELS FOR HIGH CUT

_ Plate

RAISE WHEELS FOR LOW CUT Lever

DRIVE

CONTROL

DISENGAGED

DRIVE

CONTROL

TO CONVERT MOWER Your lawn mower was shipped ready to

be used as a mulcher. To convert to bagging or discharging:

REAR BAGGING

• Lift rear door of the lawn mower and place the grass catcher frame hooks

onto the door pivot pins.

• To convert to mulching or discharging

operation, remove grass catcher and close rear door.

SIDE DISCHARGING

• Rear door must'be closed.

• Open mulcher door and install dis-

charge deflector under door as shown.

• Mower is now ready for discharging operation.

• To convert to mulching or bagging operation, discharge deflector must be

removed and mulcher door must be closed.

SIMPLE STEPS TO REMEMBER WHEN CONVERTING YOUR LAWN MOWER

FOR MULCHING -

1. Rear door closed.

2. Mulcher door closed.

FOR REAR BAGGING -

1. Grass catcher installed.

2. Mulcher door closed.

FOR SIDE DISCHARGING -

1. Rear door closed.

2. Side discharge deflector installed.

_CAUTION: Do not run your lawn mower without rear door closed or

approved grass catcher in place. Never attempt to operate the lawn mower with

the rear door removed or propped open.

_Open mulcher door

Discharge

Pivot pins Rear

Catcher frame hook

Grass

catcher

handle

BEFORE STARTING ENGINE

ADD OIL Your lawnmower is shipped without oil in

the engine. Engine holds 18.5 oz. of oil.

For type and grade of oil to use, see

"ENGINE" in the Maintenance section of this manual.

1. Be sure lawnmower is level and area

around oil fill is clean.

2. Remove engine oil cap and fill to

upper limit mark on dipstick. Pour oil slowly. Do not over fill.

NOTE: Allow oil to settle down intoengine

for accurate reading. To read proper level,

insert the dipstick into the tube and rest engine oil cap on the tube. Do not thread

the cap onto the tube. Remove and read the oil level.

3. Reinstall engine oil cap and tighten.

• Check oil level before each use. Add

oil if needed. Fill to upper limit mark on dipstick.

• Change the oil after every 25 hours of operation or each season. You may need to change the oil more often

under dusty, dirty conditions.

Oil filler cap/dipstick

Gasoline

filler cap

Oil

cap

problems, the fuel system should be

emptied before storage of 30 days or

longer. Drain the gas tank, start the

engine and let it run until the fuel lines and carburetor are empty. Use fresh fuel

next season. See Storage Instructionsfor

additional information. Never use engine or carburetor cleaner products in the fuel

tank or permanent damage may occur. A CAUTION: Fill to bottom of gas tank

filler neck. Do not overfill. Wipe off any spilled oil or fuel. Do not store, spill or

use gasoline near an open flame.

TO START ENGINE

NOTE: Due to protective coatings on the engine, a small amount of smoke may be present during the initial use of the

product and should be considered

normal.

1. Turn fuel valve to ON position.

2. To start a cold engine, move handle mounted threttle/choke control lever to

CHOKE position.

3. Hold operator presence control bar

clown to the handle and pull starter

handle quickly. Do not allow starter rope to snap back.

4. Slowly move throttle control lever to FAST position after engine starts.

• To start a warm engine, move throttle control lever to FAST or SLOW position,

then follow steps above.

TO STOP ENGINE

• To stop engine, release operator presence control bar. Wait until blade

and all moving parts have stopped and turn fuel valve to OFF position if you do

not intend to restart the engine soon.

ADD GASOLINE

• Fill fuel tank. Use fresh, clean, regular

unleaded gasoline with a minimum of

87 octane. Do not mix oil with gaso-

line. Purchase fuel in quantities that

can be used within 30 days to assure

fuel freshness. AWARNING: Experience indicates that alcohol blended fuels (called gasohol or

using ethanol or methanol) can attract moisture which leads to separation and

formation of acids during storage. Acidic gas can damage the fuel system of an

engine while in storage. To avoid engine

Fuel valve lever

MOWING TIPS

• Under certain conditions, such as very

tall grass, it may be necessary to raise the height of cut to reduce pushing

effort and to keep from overloading the engine and leaving clumps of grass clippings. It may also be necessary to reduce ground speed and/or run the

lawn mower over the area a second time.

• For extremely heavy cutting, reduce the

width of cut by overlapping previously cut path and mow slowly.

• For better grass bagging and most

cutting conditions, the engine speed should be set in the fast position.

• Pores in cloth grass catchers can

become filled with dirt and dust with use and catchers will collect less grass.

To prevent this, regularly hose catcher off with water and let dry before using.

• Keep top of engine around starter clear and clean of grass clippings and chaff.

This will help engine air flow and extend engine life.

MULCHING MOWING TIPS

IMPORTANT: For best performance, keep mower housing free of built-up

grass and trash. See "CLEANING" in the

Maintenance section of this manual.

• The special mulching blade will recut

the grass clippings many times and

reduce them in size so that as they fall

onto the lawn they will disperse into the grass and not be noticed. Also, the

mulched grass will biodegrade quickly

to provide nutrients for the lawn. Always mulch with your highest engine

(blade) speed as this will provide the best recutting action of the blades.

• Avoid cutting your lawn when it is wet.

Wet grass tends to form clumps and

interferes with the mulching action.

The best time to mow your lawn is the

early afternoon. At this time the grass has dried and the newly cut area will

not be exposed to the direct sun.

• For best results, adjust the lawn mower

cutting height so that the lawn mower cuts off only the top one-third of the

grass blades. If the lawn is overgrown it will be necessary to raise the height

of cut to reduce pushing effort and to keep from overloading the engine and leaving clumps of mulched grass. For extremely heavy mulching, reduce your

width of cut by overlapping previously

cut path and mow slowly.

MAXI_

• Certain types of grass and grass conditions may require that an area be

mulched a second time to completely hide the clippings. When doing a second cut, mow across or perpendicu-

lar to the first cut path.

• Change your cutting pattern from week to week. Mow north to south one week

then change to east to west the next week. This will help prevent matting

and graining of the lawn.

MA,NTENANCESC.EDULE

F,LL,.DATES

REGULARSERVICE /_'_£,_5_£-_,"" SERVICE DATES

Check for Loose Fasteners _#' Clean/Inspect Grass Catcher

(If Equipped) i,/ _ _'

i Clean Lawn Mower j

Clean Under Drive Cover

Check drive belt/pulleys

W (Power-Propelled Mowers)

(Power-Propelled Mowers) Ikf

IIIII /_

R Check/Sharpen/Replace Blade 1_3

LubricationChart I/

Clean Battery/Recharge

IE,_ncstartMowers) _ V%

RECheck EngineOil Level

Change En_line Oil _1,_

Inspect Muffler

G Clean Air Filter _ 2 N Clean or Replace Spark Plug

Replace Air Filter Paper Cartridge t_2

1 - Change more often when operating under a heavy load or in high ambient temperatures. 2 - Se_,lce more often when Operating in dirty or dusty conditions.

3 - Replace blades more often when mowing in sandy soil. 4 - Charge 48 hours at end of season,

GENERAL RECOMMENDATIONS The warranty on this lawn mower does

not cover items that have been subjected to operator abuse or negligence. To

receive full value from the warranty,

operator must maintain mower as instructed in this manual.

Some adjustments will need to be made periodically to properly maintain your

unit.

All adjustments in the Service and Adjustments section of this manual should be checked at least once each

season.

• Once a year, replace the spark plug, clean or replace air filter element and check blade for wear. A new spark

plug and clean/new air filter element assure proper air-fuel mixture and help your engine run better and last longer.

• Follow the maintenance schedule in this manual.

BEFORE EACH USE

1. Check engine oil level.

2, Check for loose fasteners.

LUBRICATION Keep unit well lubricated (See "LUBRI-

CATION CHART").

(_) Wheel (on each wheel)

(_) Spray lubricant (_) See "ENGINE" in Maintenance section.

LUBRICATION CHART

(]) Handle bracket mounting pins

IMPORTANT: Do not oil or grease plastic wheel bearings. Viscous

lubricants will attract dust and dirt that will shorten the life of the self-lubricat-

ing bearings. If you feel they must be lubricated, use only a dry, powdered

graphite type lubricant sparingly.

Engine oil

Mulcher

door hinge

Rear door

hinge

PRODUCT SPECIFICATIONS

SERIALNUMBER:

DATE OF PURCHASE:

GASOLINE CAPACITY/TYPE: 1.0 QUARTS UNLEADED REGULAR OILTYPE (API-SF-SJ): SAE 30 (ABOVE 32°F); SAE 5W-30 (BELOW 32°F)

OIL CAPACITY: 18.5 OUNCES

SPARK PLUG (GAP: .030") NGK BPR6ES

3LADE BOLTTORQUE: 35-40 FT. LBS.

The model and serial numbers will be found on a decal attached to the rear of the

lawn mower housing. Record both serial number and date of purchase in the space provided above.

LAWN MOWER 3. Be sure the trailing edge of blade

Always observe safety rules when performing any maintenance.

TIRES

• Keep tires free of gasoline, oil, or insect

control chemicals which can harm

rubber.

• Avoid stumps, stones, deep ruts, sharp objects and other hazards that may cause tire damage.

BLADE CARE

For best results, mower blade must be kept sharp. Replace bent or damaged

blades.

TO REMOVE BLADE

1. Disconnect spark plug wire from spark plug and place wire where it cannot

come in contact with spark plug.

2. Turn lawn mower on its side. Make sure air filter and carburetor are up.

3. Use a wood block between blade and mower housing to prevent blade from

turning when removing blade bolt.

NOTE: Protect your hands with gloves and/or wrap blade with heavy cloth.

4. Remove blade bolt by turning counter- clockwise.

5. Remove blade and attaching hard- ware (bolt, lock washer and hardened washer).

NOTE: Remove the blade adapter and

check the key inside hub of blade adapter. The key must be in good condi-

tion to work properly. Replace adapter if damaged.

TO REPLACE BLADE

1. Position the blade adapter on the engine crankshaft. Be sure key in

adapter and crankshaft keyway are aligned.

2. Position blade on the blade adapter aligning the two (2) holes in the blade

with the raised lugs on the adapter.

(opposite sharp edge) is up toward

the engine.

4. Install the blade bolt with the lock washer and hardened washer into

blade adapter and crankshaft.

5. Use block of wood between blade and

lawn mower housing and tighten the blade bolt, turning clockwise.

• The recommended tightening torque is

35-40 ft. Ibs.

IMPORTANT: Blade bolt is grade 8 heat treated.

TO SHARPEN BLADE

NOTE: We do not recommend sharpen- ing blade - but if you do, be sure the

blade is balanced.

Care should be taken to keep the blade

balanced. An unbalanced blade will

cause eventual damage to lawn mower

or engine.

• The blade can be sharpened with a file

or on a grinding wheel. Do not attempt to sharpen while on the mower.

• To check blade balance, drive a nail

into a beam or wall. Leave about one inch of the straight nail exposed. Place

center hole of blade over the head of the nail. If blade is balanced, it should

remain in a horizontal position. If either

end of the blade moves downward, sharpen the heavy end until the blade

is balanced.

Blade adapte= Crankshaft

Blade

Blade bolt Hardene

12 washer

Trailing edge Blade adapter

keyway

_Crank

shaft

GRASS CATCHER

• The grass catcher may be hosed with

water, but must be dry when used.

• Check your grass catcher often for

damage or deterioration. Through normal use it will wear. If catcher

needs replacing, replace only with a manufacturer approved replacement

catcher. Give the lawn mower model number when ordering.

DRIVE WHEELS

Check front drive wheels each time before you mow to be sure they move

freely. The wheels not turning freely means

trash, grass cuttings, etc. are in the drive wheel area and must be cleaned to free

drive wheels.

If necessary to clean the drive wheels, be

sure to clean both front wheels.

1. Remove hubcaps, hairpin cotters and washers.

2. Remove wheels from wheel adjusters.

3. Remove any trash or grass cuttings

from inside the dust cover, pinion and/ or drive wheel gear teeth.

4. Put wheels back in place.

NOTE: If after cleaning, the drive wheels

do not turn freely, contact a Sears or other

qualified service center.

GEAR CASE

• To keep your drive system working properly, the gear case and area around the drive should be kept clean and free of trash build-up. Clean under

the drive cover twice a season.

• The gear case is filled with lubricant to the proper level at the factory. The only

time the lubricant needs attention is if service has been performed on the

gear case.

• If lubricant is required, use only Texaco Starplex Premium 1 Grease, Part No.

750369. Do not substitute.

ENGINE

LUBRICATION Use only high quality detergent oil rated

with API service classification SF-SJ. Select the oil's SAE viscosity grade

according to your expected operating temperatu re.

SAE VISCOSITY GRADES

NOTE: Although multi-viscosity oils (5W30, 10W30 etc.) improve starting in

cold weather, these multi-viscosity oils will result in increased oil consumption when used above 32°1. Check your engine oil level more frequently to avoid

possible engine damage from running

low on oil.

Change the oil after every 25 hours of operation or at least once a year if the

lawn mower is not used for 25 hours in

one year. Check the crankcase oil level before

starting the engine and after each five (5)

hours of continuous use. Tighten oil plug

securely each time you check the oil

level.

TO CHANGE ENGINE OIL

NOTE: Before tipping lawn mower to drain oil, drain fuel tank by running engine until fuel tank is empty.

1. Disconnect spark plug wire from spark plug and place wire where it cannot

come in contact with spark plug.

2. Remove engine oil cap; lay aside on a clean surface.

3. Tip lawn mower on its side as shown and drain oil into a suitable container.

Rock lawn mower back and forth to remove any oil trapped inside of

engine.

4. Wipe off any spilled oil from lawn mower or side of engine.

5. Fill engine with oil. (See "ADD OIL" in the Operation section of this manual.)

6. Reconnect spark plug wire to spark plug.

Oil filler cap/dipstick

=2O

-30 -10 0 _0 20 30 40

TEMPERATURE RANGE ANTICIPATED BEFORE NEXT OIL CHANGE

AIR FILTER

Your engine will not run properly and may

be damaged by using a dirty air filter. Replace the air filter every 100 hours of

operation or every season, whichever occurs first. Service air cleaner more

often under dusty conditions.

TO CLEAN AIR FILTER

1. Remove cover.

2. Carefully remove cartridge.

3. Clean by gently tapping on a flat surface. If very dirty, replace cartridge.

_CAUTION: Petroleum solvents, such as kerosene, are r_ot to be used to clean

cartridge. They may cause deterioration of the cartridge. Do not oil cartridge. Do not

use pressurized air to clean or dry

cartridge.

4. Install cartridge, then replace cover.

Filter Filter

Cover

Tabs

SPARK PLUG

Replace spark plugs at the beginning of

each mowing season or after every 100 hours of operation, whichever occurs first.

Spark plug type and gap setting are

shown in "PRODUCT SPECIFICATIONS"

in Maintenance section of this manual.

CLEANING IMPORTANT: For best performance,

keep mower housing free of built-up grass and trash. Clean the underside of

_tour mower after each use.

CAUTION: Disconnect spark plug wire

from spark plug and place wire where it cannot come in contact with the spark

plug.

• Clean the underside of your lawn mower by scraping to remove build-up

of grass and trash.

• Clean engine often to keep trash from accumulating. A clogged engine runs hotter and shortens engine life.

• Keep finished surfaces and wheels free of all gasoline, oil, etc.

• We do not recommend using a garden hose to clean lawn mower unless the

electrical system, muffler, air filter and carburetor are covered to keep water

out. Water in engine can result in shortened engine life.

MUFFLER Tabs Inspect and replace corroded muffler as it

could create a fire hazard and/or dam- age.

_,CAUTION: Before performing any service or adjustments:

1. Release control bar and stop engine.

2. Make sure the blade and all moving parts have completely stopped.

3. Disconnect spark plug wire from spark plug and place where it cannot come

in contact with plug.

LAWN MOWER

TO ADJUST CUTTING HEIGHT See "TO ADJUST CU-I-rlNG HEIGHT' in

the Operation section of this manual. REAR DEFLECTOR

The rear deflector, attached between the rear wheels of your mower, is provided to

minimize the possibility that objects will be thrown out of the rear of the mower

CLEAN UNDER DRIVE COVER Clean under drive cover at least twice a

season. Scrape underside of cover with putty knife or similar tool to remove any build-up of trash or grass on underside of

drive cover.

into the operator mowing position. If the deflector becomes damaged, it should be

replaced.

TO REMOVE/REPLACE DRIVE BELT

1. Remove drive cover. Remove belt from gearcase pulley by pushing

down on pulley and rolling belt off it.

2. Turn lawn mower on its side with air

filter and carburetor up.

3. Remove blade.

4. Remove debris shield.

5. Remove belt from engine pulley on

crankshaft.

6. Install new belt by reversing above

steps.

7. Always use factory approved belt to assure fit and tong life.

Drive cover Belt

Push

TO ADJUST HANDLE The upper handle may be adjusted to

four (4) different height positions.

1. Loosen both handle knobs only

enough to allow the upper handle to pivot to the desired adjustment

position.

2. Tighten both handle knobs securely.

Handle

knob

TO ASSEMBLE GRASS CATCHER

1. Put grass catcher frame into grass bag with rigid part of bag on the bottom.

Make sure the frame handle is outside of the bag top.

2. Slip vinyl bindings over frame. NOTE: If vinyl bindings are too stiff, hold

them in warm water for a few minutes. If bag gets wet, let it dry before using.

• i_CAUTION: Do not run your lawn mower without clipping deflector or approved

grass catcher in place. Never attempt to operate the lawn mower with the rear

door removed or propped open.

ENGINE

ENGINE SPEED

Your engine speed has been factory set.

Do not attempt to increase engine speed or it may result in personal injury. If you believe that the engine is running too fast

or too slow, take your lawn mower to a Sears or other qualified service center for

repair and adjustment.

CARBURETOR ADJUSTMENTS

The carburetor on your engine is low

emission. The idle mixture screw is fitted

with a limiter cap that prevents excessive

enrichment of the air-fuel mixture in order

to comply with emissions regulations and

is not adjustable.

Do not attempt to remove the limiter cap to make adjustments. The limiter cap cannot be removed without breaking the

idle mixture screw.

IDLE SPEED SETTING - Adjustment will require the assistance of

an additional person to hold down the operator presence control bar.

1. Start engine and allow to warm for five minutes.

2. With throttle control lever in slow position, engine should idle at 2100

RPM. If engine idles too slow or fast,

turn throttle stop screw in or out until correct idle is attained.

IMPORTANT: Never tamper with the engine governor, which is factory set for proper engine speed. Overspeeding the engine above the factory high speed

setting can be dangerous. If you think the engine-governed high speed needs adjusting, contact a Sears or other qualified service center, which has proper

equipment and experience to make any necessary adjustments.

Throttle stop screw

Catcher frame handk

Limiter cap

Frame

opening 15

+ 33 hidden pages

Craftsman 917378212 Owner’s Manual

Specifications and Main Features

Frequently Asked Questions

User Manual