Craftsman 917277252 Owner’s Manual

Owner's Manual

CRRFTSMRN°

LAWN TRACTOR

15.5 HE 38" Mower Electric Start

5 Speed Transaxle

Model No.

917.277252

i_ This product has a low emission engine which operates

IMPORTANT:

Read and follow all Safety Rules and Instructions before

operating this equipment.

Sears, Roebuck and Co., Hoffman Estates, IL 60179 U.S.A.

Visit our Craftsman website:www.sears.com/craftsman

differently from previously built engines. Before you start the engine, read and understand this Owner's Manual.

For answers to your questions about

this product, Call:

1-800-659-5917

Sears Craftsman Help Line

5 am -5 pm, Mon - Sat

Warranty.................................................2

SafetyRules...........................................3

ProductSpecifications............................6

Assembly/Pre-Operation........................8

Operation..............................................11

MaintenanceSchedule.........................17

Maintenance.........................................17

ServiceandAdjustments......................21

Storage.................................................27

Troubleshooting....................................28

RepairParts..........................................32

SearsService.........................BackCover

LIMITEDWARRANTYONCRAFTSMANRIDINGEQUIPMENT Fortwo (2)yearsfromthedate ofpurchase,if thisCraftsmanRidingEquipmentis

maintained,lubricatedandtuned upaccordingto theinstructionsinthe owner'smanual, Searswill repairorreplacefree of chargeanyparts thatare foundto bedefectivein

materialor workmanshipaccordingto theguidelinesofcoveragelistedbelow.Searswill alsoprovidefreelaborfor theseapplicablewarrantedpartsforthe twofullyears.During

thefirst 30 daysof purchase,therewill benochargesto servicethe productatyour

homefor issuescoveredby thiswarranty.(Seeexclusionsbelow). Foryourconve- nience, INHOMEwarrantyservicewill stillbe availableafterthefirst 30 daysofpur-

chase, butatrip chargewillapply.Thischargewill bewaivedifthe Craftsmanproductis

droppedoff atan authorizedSearslocation.Forthe nearestauthorizedSearslocation, pleasecall 1-800-4-MY-HOME®.Thiswarrantyapplies onlywhilethis productis within

the UnitedStates. ThisWarrantydoesnotcover:

• Expendableitemswhich becomeworn duringnormaluse,includingbut notlimitedto blades,spark plugs,air cleaners,belts,andoilfilters.

StandardMaintenanceServicing,oil changes, or tune-ups

• Tire replacementorrepaircausedbypuncturesfromoutsideobjects,suchasnails, thorns,stumps,or glass.

• Repairsnecessarybecauseof operatorabuse, includingbutnot limitedto, damage causedby towingobjectsbeyondthe capabilityofthe ridingequipment,impacting

objectsthat bendthe frameorcrankshaft,or over-speedingtheengine.

• Repairsnecessarybecauseof operatornegligence,includingbutnot limitedto, elec- tricaland mechanicaldamagecausedbyimproperstorage,failureto usethe proper

gradeandamountof engineoil, failureto keepthe deckclear of flammabledebris, orfailureto maintainthe equipmentaccordingtothe instructionscontainedinthe

owner'smanual.

• Engine(fuelsystem)cleaningor repairscausedby fueldeterminedto becontami- natedor oxidized(stale). Ingeneral,fuelshouldbeused within30 daysof itspur-

chasedate.

• Normaldeteriorationandwearof theexteriorfinishes,or productlabelreplacement.

• Ridingequipmentusedfor commercialor rentalpurposes.

LIMITEDWARRANTYON BATTERY Forninety(90)daysfrom dateofpurchase,if anybatteryincludedwith this ridingequip-

mentprovesdefectivein materialor workmanshipandourtestingdeterminesthe battery

will not holdacharge,Searswill replacethe batteryatno charge. Duringthe first30

daysofpurchase,therewillbe no chargesto replacethe batteryatyour HOME. After

thefirst 30 days,foryour convenience,IN-HOMEwarrantyservicewill stillbe avail-

ablebut atripchargewillapply. This chargewill bewaivedifthe Craftsmanproductis droppedoff atan authorizedSearslocation.Forthe nearestauthorizedSearslocation,

pleasecall 1-800-4-MY-HOME@.

Thisbattery warrantyappliesonlywhile thisproductiswithinthe UnitedStates. Thiswarrantygivesyou specificlegalrights,andyou mayalso haveotherrights,which

vary,fromstateto state.

Sears, Roebuck and Co.,Dept.817WA, Hoffman Estates, IL 60179

IMPORTANT: This cutting machine is capable of amputating hands and feet and throw- ing objects. Failure to observe the following safety instructions could result in serious

injury or death.

WARNING: In order to prevent

accidental starting when setting up,

transporting, adjusting or making repairs,

always disconnect spark plug wire and place wire where it cannot contact spark

plug.

WARNING: Do not coast down a

hill in neutral, you may lose control of the

tractor.

WARNING: Tow only the attach-

ments that are recommended by and

comply with specifications of the man-

ufacturer of your tractor. Use common sense when towing. Operate only at the lowest possible speed when on a slope.

Too heavy of a load, while on a slope, is

dangerous. Tires can lose traction with

the ground and cause you to lose control

of your tractor.

WARNING: Engine exhaust, some

of its constituents, and certain vehicle

components contain or emit chemicals

known to the State of California to cause

cancer and birth defects or other repro-

ductive harm.

WARNING: Battery posts, terminals

and related accessories contain lead and lead compounds, chemicals known to the

State of California to cause cancer and birth defects or other reproductive harm.

Wash hands after handling.

I. GENERAL OPERATION

• Read, understand, and follow all instructions on the machine and in the

manual before starting.

• Do not put hands or feet near rotating parts or under the machine. Keep clear of the discharge opening at all times.

• Only allow responsible adults, who are familiar with the instructions, to operate

the machine.

• Clear the area of objects such as rocks, toys, wire, etc., which could be picked up and thrown by the blades.

• Be sure the area is clear of bystand- ers before operating. Stop machine if

anyone enters the area.

• Never carry passengers.

• Do not mow in reverse unless abso- lutely necessary. Always look down

and behind before and while backing.

• Never direct discharged material

toward anyone. Avoid discharging

material against a wall or obstruction. Material may ricochet back toward the

operator. Stop the blades when cross-

ing gravel surfaces.

• Do not operate machine without the

entire grass catcher, discharge guard, or other safety devices in place and working.

• Slow down before turning.

• Never leave a running machine unattended. Always turn off blades,

set parking brake, stop engine, and

remove keys before dismounting.

• Disengage blades when not mowing.

Shut off engine and wait for all parts to come to a complete stop before clean-

ing the machine, removing the grass

catcher, or unclogging the discharge guard.

• Operate machine only in daylight or

good artificial light.

• Do not operate the machine while under the influence of alcohol or drugs.

• Watch for traffic when operating near

or crossing roadways.

• Use extra care when loading or unload- ing the machine into a trailer or truck.

• Always wear eye protection when oper-

ating machine.

• Data indicates that operators, age 60

years and above, are involved in a

large percentage of riding mower-re- lated injuries. These operators should

evaluate their ability to operate the

riding mower safely enough to protect

themselves and others from serious

injury.

• Follow the manufacturer's recommen-

dation for wheel weights or counter- weights.

• Keep machine free of grass, leaves or

other debris build-up which can touch

hot exhaust / engine parts and burn. Do not allow the mower deck to plow

leaves or other debris which can cause build-up to occur. Clean any oil or fuel

spillage before operating or storing the

machine. Allow machine to cool before

storage.

I1.SLOPE OPERATION Slopesare a majorfactorrelatedto lossof

controlandtip-overaccidents,whichcan

resultinsevereinjuryor death. Opera-

tion onallslopes requiresextra caution. If

you cannot back up the slope or if you feel

uneasy on it, do not mow it.

• Mow up and down slopes, not across.

• Watch for holes, ruts, bumps, rocks, or other hidden objects. Uneven terrain

could overturn the machine. Tall grass can hide obstacles.

• Choose a low ground speed so that

you will not have to stop or shift while

on the slope.

• Do not mow on wet grass. Tires may lose traction.

Always keep the machine in gear when

going down slopes. Do not shift to neutral and coast downhill.

• Avoid starting, stopping, or turning on a slope. If the tires lose traction, dis-

engage the blades and proceed slowly

straight down the slope.

• Keep all movement on the slopes slow and gradual. Do not make sudden

changes in speed or direction, which could cause the machine to roll over.

• Use extra care while operating ma-

chine with grass catchers or other at- tachments; they can affect the stability

of the machine. Do no use on steep slopes.

• Do not try to stabilize the machine by putting your foot on the ground.

• Do not mow near drop-offs, ditches, or embankments. The machine could

suddenly roll over if a wheel is over the

edge or if the edge caves in.

III. CHILDREN

Tragic accidents can occur if the operator

is not alert to the presence of children. Children are often attracted to the machine

and the mowing activity. Never assume

that children will remain where you last

saw them.

• Keep children out of the mowing area and in the watchful care of a respon- sible adult other than the operator.

• Be alert and turn machine off if a child

enters the area.

• Before and while backing, look behind and down for small children.

• Never carry children, even with the blades shut off. They may fall off and be seriously injured or interfere with

safe machine operation. Children who

have been given rides in the past may

suddenly appear in the mowing area for another ride and be run over or

backed over by the machine.

• Never allow children to operate the machine.

• Use extra care when approaching blind

corners, shrubs, trees, or other objects that may block your view of a child.

IV. TOWING

• Tow only with a machine that has a hitch designed for towing. Do not at-

tach towed equipment except at the

hitch point.

• Follow the manufacturer's recommen-

dation for weight limits for towed equip-

ment and towing on slopes.

• Never allow children or others in or on

towed equipment.

• On slopes, the weight of the towed

equipment may cause loss of traction and loss of control.

• Travel slowly and allow extra distance

to stop.

V. SERVICE SAFE HANDLING OF GASOLINE To avoid personal injury or property

damage, use extreme care in handling gasoline. Gasoline is extremely flammable and the vapors are explosive.

• Extinguish all cigarettes, cigars, pipes,

and other sources of ignition.

• Use only approved gasoline container.

• Never remove gas cap or add fuel with

the engine running. Allow engine to cool before refueling.

• Never fuel the machine indoors.

• Never store the machine or fuel con-

tainer where there is an open flame, spark, or pilot light such as on a water

heater or other appliances.

• Never fill containers inside a vehicle

or on a truck or trailer bed with plastic

liner. Always place containers on the

ground away from your vehicle when filling.

• Removegas-poweredequipmentfrom thetruckor trailerand refuelit on the

ground.If thisis not possible,then refuelsuchequipment with a portable

container, rather than from a gasoline dispenser nozzle.

• Keep the nozzle in contact with the rim of the fuel tank or container opening at all times until fueling is complete. Do not use a nozzle lock-open device.

• If fuel is spilled on clothing, change clothing immediately.

• Never overfill fuel tank. Replace gas cap and tighten securely.

GENERAL SERVICE

• Never operate machine in a closed area.

• Keep all nuts and bolts tight to be sure the equipment is in safe working condi-

tion.

• Never tamper with safety devices.

Check their proper operation regularly.

• Keep machine free of grass, leaves, or other debris build-up. Clean oil or fuel

spillage and remove any fuel-soaked debris. Allow machine to cool before

storing.

• If you strike a foreign object, stop and

inspect the machine. Repair, if neces-

sary, before restarting.

• Never make any adjustments or repairs with the engine running.

• Check grass catcher components and the discharge guard frequently and

replace with manufacturer's recom- mended parts, when necessary.

• Mower blades are sharp. Wrap the

blade or wear gloves, and use extra

caution when servicing them.

• Check brake operation frequently. Ad-

just and service as required.

• Maintain or replace safety and instruc- tion labels, as necessary.

• Be sure the area is clear of bystand- ers before operating. Stop machine if anyone enters the area.

• Never carry passengers.

• Do not mow in reverse unless abso- lutely necessary. Always look down

and behind before and while backing.

• Never carry children, even with the blades shut off. They may fall off and be seriously injured or interfere with safe machine operation. Children who have been given rides in the past may suddenly appear in the mowing area

for another ride and be run over or backed over by the machine.

• Keep children out of the mowing area and in the watchful care of a respon- sible adult other than the operator.

• Be alert and turn machine off if a child enters the area.

• Before and while backing, look behind and down for small children.

• Mow up and down slopes (15 ° Max),

not across.

• Choose a low ground speed so that you will not have to stop or shift while on the slope.

• Avoid starting, stopping, or turning on a slope. If the tires lose traction, dis- engage the blades and proceed slowly straight down the slope.

• If machine stops while going uphill, disengage blades, shift into reverse and back down slowly.

• Do not turn on slopes unless neces- sary, and then, turn slowly and gradu- ally downhill, if possible.

PRODUCT SPECIFICATIONS

Gasoline 1.25 Capacity and Unleaded

Type: Regular Oil Type SAE 30 (above 32°F)

'API-SG-SL): SAE 5W-30(below 32°F Oil Capacity: 3.0 Pints Spark Plug: Champion RC12YC

(Gap: .030") Ground Speed Forward:

(MPH): 1st 1.1

2nd 2.2

3rd 3.3 4th 4.4 5th 4.9

Reverse: 1.4

Tire Pressure: Front: 14 PSI

Rear: 12 PSI

Charging System: 3 Amps Battery

5 Amps Headlights

Battery: Amp/Hr: 28

Min. CCA: 230 Case Size: U1R

Blade Bolt Torque: 27-35 Ft. Lbs.

CONGRATULATIONS on your purchase of a new tractor. It has been designed, engi-

neered and manufactured to give you the best possible dependability and performance. Should you experience any problem you

cannot easily remedy, please contact a

Sears or other qualified service center.

We have competent, well-trained techni- cians and the proper tools to service or

repair this tractor. Please read and retain this manual. The

instructions will enable you to assemble and maintain your tractor properly. Always

observe the "SAFETY RULES". CUSTOMER RESPONSIBILITIES

• Read and observe the safety rules.

• Follow a regular schedule in main- taining, caring for and using your tractor.

• Follow the instructions under "Mainte-

nance" and "Storage" sections of this owner's manual.

_,WARNING: This tractor is equipped

with an internal combustion engine and should not be used on or near any unim-

proved forest-covered, brush-covered or grass-covered land unless the engine's exhaust system is equipped with a spark

arrester meeting applicable local or state laws (if any). If a spark arrester is used, it

should be maintained in effective working order by the operator.

In the state of California the above is re-

quired by law (Section 4442 of the Califor- nia Public Resources Code). Other states may have similar laws. Federal laws apply on federal lands. A spark arrester for the muffler is available through your nearest Sears service center (See REPAIR PARTS section of this manual).

REPAIR PROTECTION

AGREEMENTS

Congratulations on making a smart pur- chase. Your new Craftsman® product is designed and manufactured for years of dependable operation. But like all products, it may require repair from time to time. That's when having a Repair Protection Agreement can save you money and aggravation.

Purchase a Repair Protection Agreement now and protect yourself from unexpected hassle and expense.

Here's what's included in the Agreement:

• Expert service by our 12,000 profe-

sional repair specialists.

• Unlimited service and no charge for

parts and labor on all covered repairs.

• Product replacement if your covered

product can't be fixed.

• Discount of 10% from regular price of

service and service-related parts not covered by the agreement; also, 10%

off regular price of preventive mainte- nance check.

• Fast help by phone- phone support

from a Sears technician on products requiring in-home repair, plus conve-

nient repair scheduling. Once you purchase the Agreement, a simple phone call is all that it takes for you to schedule service. You can call anytime day or night, or schedule a service ap- pointment online. Sears has over 12,000 professional repair specialists, who have access to over 4.5 million quality parts and accessories. That's the kind of professionalism you can count on to help prolong the life of your new purchase for years to come. Purchase your Repair Protection Agreement today! Some limitations and exclusions apply. For prices and additional information

call 1-800-827-6655. SEARS INSTALLATION SERVICE

For Sears professional installation of home appliances, garage door openers, water heaters, and other major home items, in

the U.S.A. call 1-800-4-MY-HOME®

Steering Wheel

Steering

Wheel Insert

_t_oeritg

_ Steering Wheel

i I I i

Adapter

(1) 5/16 Lock Washer

(1) Hex Bolt 5/16-18 x 4

Seat

(1) Large Flat Washer

Steering

Extension

Shaft

Keys

(2) Keys

(1) Washer

@ 17/32 x1-3/16 x12 Gauge

_(1 ) Knob

(1) Oil Drain Tube For Future Use

Slope Sheet

Your new tractor has been assembled at the factory with the exception of those parts left

unassembled for shipping purposes. To ensure safe and proper operation of your tractor all parts and hardware you assemble must be tightened securely. Use the correct tools as necessary to insure proper tightness.

TOOLS REQUIRED FOR ASSEMBLY

A socket wrench set will make assembly easier. Standard wrench sizes you need

are listed below. (1) 3/4" wrench (1) Pliers

(2) 7/16" wrench (1) Utility knife (1) Tire pressure gauge

When right or left hand is mentioned in this manual, it means when you are in the operating position (seated behind the

steering wheel).

TO REMOVE TRACTOR FROM

CARTON UNPACK CARTON

1. Remove all accessible loose parts and parts boxes from carton.

2. Cut along dotted lines on all four pan- els of carton. Remove end panels and

lay side panels flat.

3. Check for any additional loose parts or cartons and remove.

Steering Wheel i

Insert

5/16 Hex Bolt 5/16 Lock

Washer

Large Flat

Washer

Steering

BEFORE REMOVING TRACTOR

FROM SKID

ATTACH STEERING WHEEL

ASSEMBLE EXTENSION SHAFT AND

BOOT

1. Slide extension shaft onto lower steer-

ing shaft.

2. Place tabs of steering boot over tab slots in dash and push down to secure.

INSTALL STEERING WHEEL

3. Position front wheels of the tractor so they are pointing straight forward.

4. Remove steering wheel adapter from steering wheel and slide adapter onto steering shaft extension.

5. Position steering wheel so cross bars are horizontal (left to right) and slide

inside boot and onto adapter.

6. Assemble large flat washer, 5/16 lock washer, 5/16 hex bolt and tighten

securely.

7. Snap steering wheel insert into center

of steering wheel.

8. Remove protective materials from trac- tor hood and grill.

IMPORTANT: Check for and remove any staples in skid that may puncture tires

where tractor is to roll off skid.

INSTALL SEAT

Adjust seat before tightening adjustment

knob.

1. Remove adjustment knob and flat washer securing seat to cardboard

packing and set aside for assembly of seat to tractor.

2. Pivot seat upward and remove from the cardboard packing. Remove the cardboard packing and discard.

3. Place seat on seat pan so head of shoulder bolt is positioned over large slotted hole in pan.

4. Push down on seat to engage shoulder bolt in slot and pull seat towards rear of

tractor.

5. Pivotseatandpanforwardandas- sembleadjustmentknoband flat washerloosely.Donottighten.

6. Lowerseatinto operatingpositionand sitin seat.

7. Slideseatuntila comfortableposition isreachedwhichallowsyou to press clutch/brakepedalallthewaydown.

8. Getoff seatwithoutmovingits ad- justed position.

9. Raiseseatandtightenadjustment knobsecurely.

Seat

Discard Terminal Caps

Keps

Terminal

Cover

Positive" Cable Negative (E Cable

Nut _ Hex Bolt

tf_

Seat

Bolt

Flat Washer

Adjustment Knob

CONNECT BATTERY

_,CAUTION: Do not short battery terminals by allowing a wrench or any

other object to contact both terminals at

the same time. Before connecting battery,

remove metal bracelets, wristwatch bands, rings, etc.

Positive terminal must be connected

first to prevent sparking from accidental

grounding.

• Lift seat pan to raised position.

• Remove terminal protective caps and discard.

• If this battery is put into service after month and year indicated on label (label

located between terminals) charge battery for minimum of one hour at 6-10 amps. (See "BATTERY" in the Mainte- nance section of this manual for charg- ing instructions).

• First connect RED battery cable to posi- tive (+) terminal with hex bolt and keps nut as shown. Tighten securely. Slide

terminal cover over terminal.

• Connect BLACK grounding cable to negative (-) terminal with remaining hex bolt and keps nut. Tighten securely.

Seat Pan

Label

NOTE: You may now roll or drive your

tractor off the skid. Follow the appropriate

instruction below to remove the tractor

from the skid.

TO ROLL TRACTOR OFF SKID (See

Operation section for location and

function of controls)

1. Press lift lever plunger and raise attachment lift lever to its highest po-

sition.

2. Release parking brake by depressing clutch/brake pedal.

3. Place gearshift lever in neutral (N) position.

4. Roll tractor forward off skid.

5. Remove banding holding deflector shield up against tractor.

TO DRIVE TRACTOR OFF SKID (See

Operation section for location and

function of controls)

,_WARNING: Before starting, read, un-

derstand and follow all instructions in the Operation section of this manual. Be sure

tractor is in a well-ventilated area. Be sure the area in front of tractor is clear of other

people and objects.

1. Be sure all the above assembly steps have been completed.

2. Check engine oil level and fill fuel tank with gasoline.

3. Sit on seat in operating position, depress clutch/brake pedal and set the parking brake.

4. Place gear shift lever in neutral (N) position.

5. Press lift lever plunger and raise attachment lift lever to its highest posi-

tion.

6. Start the engine. After engine has started, move throttle control to idle

position.

7. Depress clutch/brake pedal into full "BRAKE" position and hold. Move gearshift lever to 1st gear.

8. Slowly release clutch/brake pedal and slowly drive tractor off skid.

9. Apply brake to stop tractor, set park- ing brake and place gearshift lever in neutral position.

10.Turn ignition key to "STOP" position.

Continue with the instructions that follow. CHECK TIRE PRESSURE

The tires on your tractor were overin- flated at the factory for shipping purposes.

Correct tire pressure is important for best

cutting performance.

• Reduce tire pressure to PSI shown in "PRODUCT SPECIFICATIONS" section

of this manual.

CHECK DECK LEVELNESS For best cutting results, mower hous-

ing should be properly leveled. See "TO LEVEL MOWER HOUSING" in the Service

and Adjustments section of this manual.

CHECK FOR PROPER POSITION OF ALL BELTS

See the figures that are shown for replac- ing motion and mower blade drive belts

in the Service and Adjustments section of this manual. Verify that the belts are routed correctly.

CHECK BRAKE SYSTEM After you learn how to operate your trac-

tor, check to see that the brake is properly adjusted. See "TO ADJUST BRAKE" in the Service and Adjustments section of

this manual.

,/CHECKLIST

Before you operate and enjoy your new tractor, we wish to assure that you receive

the best performance and satisfaction from this Quality Product. Please review the following checklist: ,/All assembly instructions have been

completed.

,/No remaining loose parts in carton. ,/Battery is properly prepared and

charged. (Minimum 1 hour at 6 amps).

,/Seat is adjusted comfortably and tight-

ened securely.

,/All tires are properly inflated. (For ship-

ping purposes, the tires were overin-

flated at the factory).

,/Be sure mower deck is properly leveled

side-to-side/front-to-rear for best cutting results. (Tires must be properly inflated

for leveling).

,/Check mower and drive belts. Be sure

they are routed properly around pulleys

and inside all belt keepers.

,/Check wiring. See that all connections

are still secure and wires are properly

clamped. While learning how to use your tractor, pay extra attention to the following important

items:

,/Engine oil is at proper level. ,/Fuel tank is filled with fresh, clean, regu-

lar unleaded gasoline.

,/Become familiar with all controls - their

location and function. Operate them before you start the engine.

,/Be sure brake system is in safe oper-

ating condition.

These symbols may appear on your tractor or in literature supplied with the product.

Learn and understand their meaning.

R N H L I\1

REVERSE NEUTRAL HIGH LOW CHOKE FAST

ENGINE OFF LIGHTS ON ENGINE ON ENGINE START PARKING BRAKE

OVER TEMP

LIGHT

BATTERY REVERSE FORWARDFUEL OIL PRESSURE

®@@@@

A'n'ACHMENT

CLUTCH ENGAGED

FREE WHEEL

(Automatic Models only)

ATTACHMENT

CLUTCH DISENGAGED

DANGER, KEEP HANDS

AND FEET AWAY

DANGER indicatesa hazard which, if not avoided,

will result in death or serious injury.

WARNING indicates a hazard which, if not avoided,

could result in death or serious injury.

CAUTION indicates a hazard which, if not avoided,

might result in minor or moderate injury.

KEEP AREA CLEAR SLOPE HAZARDS

0#-,0

SLOW IGNITION

PARKING BRAKE PARKING BRAKE

LOCKED UNLOCKED

MOWER HEIGHT MOWER LIFT

(SEE SAFETY RULES SECTION)

Failure to follow instructions could result in serious injury or

death. The safety alert symbol is used to identify safety inform-

ation about hazards which can result in death, serious injury

and/or property damage.

,_hlll/lll_llh_,

CAUTION when used without the alert symbol, indicates a situation that could result in damage

to the tractor and/or engine.

NOT SURFACES indicates a hazard which, if not avoided, could result in death, serious injury

and/or property damage. FIRE indicates a hazard which, if not avoided,

could result in death, serious injury and/or property damage.

KNOW YOUR TRACTOR READ THIS OWNER'S MANUAL AND SAFETY RULES BEFORE OPERATING YOUR

TRACTOR

Compare the illustrations with your tractor to familiarize yourself with the locations of

various controls and adjustments. Save this manual for future reference.

Th rottle/Choke

Control

Clutch/Brake Pedal

Attachment Clutch Lever

Ignition Switch Light Switch

Parking Brake Lever

Position

Lift Lever Plunger

Attachment Lift Lever

Height

Adjustment

Indicator

Gearshift Lever

Our tractors conform to the safety standards of the

American National Standards Institute.

ATTACHMENT CLUTCH LEVER - Used to engage the mower blades, or other at-

tachments mounted to your tractor. ATTACHMENT LIFT LEVER - Used to

raise, lower, and adjust the mower deck or other attachments mounted to your tractor.

CLUTCH/BRAKE PEDAL - Used for declutching and braking the tractor and

starting the engine. GEARSHIFT LEVER - Selects the speed

and direction of tractor.

IGNITION SWITCH - Used for starting and stopping the engine.

LIFT LEVER PLUNGER - Used to release attachment lift lever when changing its

position. LIGHT SWITCH POSITION - Turns the

headlights on and off. PARKING BRAKE LEVER - Locks clutch/

brake pedal into the brake position. THROTTLE/CHOKE CONTROL - Used

for starting and controlling engine speed.

The operation of any tractor can result in foreign objects thrown into the eyes, which can result in severe eye damage. Always wear safety

glasses or eye shields while operating your tractor or performing any adjustments or repairs. We recommend a wide vision safety mask over spectacles or standard safety glasses.

HOW TO USE YOUR TRACTOR

TO SET PARKING BRAKE

Your tractor is equipped with an operator

presence sensing switch. When engine is running, any attempt by the operator

to leave the seat without first setting the

parking brake will shut off the engine.

1. Depress clutch/brake pedal all the way down and hold.

2. Pull parking brake lever up and release pressure from clutch/brake pedal.

Pedal should remain in brake position. Make sure parking brake will hold trac-

tor secure.

Attachment Clutch Lever

Throttle/

Choke

"Brake"

Position

Clutch/Brake "Disengaged" Lever Pedal Position

STOPPING

MOWER BLADES -

• To stop mower blades, move attachment

clutch lever to "DISENGAGED" position.

GROUND DRIVE -

• To stop ground drive, depress clutch/

brake pedal all the way down.

• Move gearshift lever to neutral (N)

position.

ENGINE -

• Move throttle control between half and

full speed (fast) position.

NOTE: Failure to move throttle control between half and full speed (fast) posi-

tion, before stopping, may cause engine to

"backfire".

• Turn ignition key to "STOP" position and

remove key. Always remove key when leaving tractor to prevent unauthorized

use.

• Never use choke to stop engine.

"Enc Position

nition Key

,"Disengaged"

Position

Parking Brake

"Engaged"

Position

Gearshift

IMPORTANT: Leaving the ignition switch in any position other than "STOP" will

cause the battery to discharge and go dead.

NOTE: Under certain conditions when

tractor is standing idle with the engine

running, hot engine exhaust gases may cause "browning" of grass. To eliminate this possibility, always stop engine when stopping tractor on grass areas.

,_CAUTION: Always stop tractor com-

pletely, as described above, before leaving the operator's position.

TO USE THROTTLE CONTROL Always operate engine at full throttle.

• Operating engine at less than full

throttle reduces the battery charging

rate.

• Full throttle offers the best bagging and

mower performance.

TO MOVE FORWARD AND BACKWARD

The direction and speed of movement is controlled by the gearshift lever.

1. Start tractor with clutch/brake pedal de- pressed and gearshift lever in neutral (N) position.

2. Move gearshift lever to desired po- sition.

3. Slowly release clutch/brake pedal to start movement.

IMPORTANT: Bring tractor to a complete

stop before shifting or changing gears.

Failure to do so will shorten the useful life

of your transaxle. TO ADJUST MOWER CUTTING HEIGHT

The position of the attachment lift lever determines the cutting height.

• Grasp lift lever.

• Press plunger with thumb and move

lever to desired position.

The cutting height range is approxi-

mately 1-1/2 to 4". The heights are mea-

sured from the ground to the blade tip with the engine not running. These heights are approximate and may vary depending

upon soil conditions, height of grass and

types of grass being mowed.

• The average lawn should be cut to ap- proximately 2-1/2 inches during the cool season and to over 3 inches during hot months. For healthier and better looking lawns, mow often and after moderate growth.

• For best cutting performance, grass over 6 inches in height should be mowed twice. Make the first cut relatively high; the second to desired height.

TO OPERATE MOWER Your tractor is equipped with an operator

presence sensing switch. Any attempt

by the operator to leave the seat with the engine running and the attachment clutch engaged will shut off the engine. You must

remain fully and centrally positioned in the

seat to prevent the engine from hesitating

or cutting off when operating your equip-

ment on rough, rolling terrain or hills.

1. Select desired height of cut.

2. Start mower blades by engaging at-

tachment clutch control.

TO STOP MOWER BLADES -

disengage attachment clutch control. _CAUTION: Do not operate the mower

without either the entire grass catcher,

on mowers so equipped, or the deflector

shield in place.

Lift

Lever High Position

Attachment f,,_

Clutch Lever ,,!"-'_ Low "Engaged

Position Position

"Disengag

Position

Shield

TO OPERATE ON HILLS

,_WARNING: Do not drive up or down

hills with slopes greater than 15° and do

not drive across any slope. Use the slope

guide at the back of this manual.

• Choose the slowest speed before start-

ing up or down hills.

• Avoid stopping or changing speed on

hills.

• If slowing is necessary, move throttle control lever to slower position.

• If stopping is absolutely necessary, push clutch/brake pedal quickly to brake posi- tion and engage parking brake.

• Move gearshift lever to 1st gear. Be

sure you have allowed room for tractor

to roll slightly as you restart movement.

• To restart movement, slowly release

parking brake and clutch/brake pedal.

• Make all turns slowly.

TO TRANSPORT

• Raise attachment lift to highest position with attachment lift control.

• When pushing or towing your tractor,

be sure gearshift lever is in neutral (N) position.

• Do not push or tow tractor at more than five (5) MPH.

NOTE: To protect hood from damage when transporting your tractor on a truck or a trailer, be sure hood is closed and secured to tractor. Use an appropriate means of tying hood to tractor (rope, cord,

etc.).

TOWING CARTS AND OTHER ATTACH- MENTS

Tow only the attachments that are recom- mended by and comply with specifications

of the manufacturer of your tractor. Use common sense when towing. Too heavy

of a load, while on a slope, is dangerous. Tires can lose traction with the ground and

cause you to lose control of your tractor.

BEFORE STARTING THE ENGINE

CHECK ENGINE OIL LEVEL The engine in your tractor has been

shipped, from the factory, already filled with summer weight oil.

1. Check engine oil with tractor on level ground.

2. Remove oil fill cap/dipstick and wipe clean, reinsert the dipstick and screw cap tight, wait for a few seconds, re-

move and read oil level. If necessary,

add oil until "FULl" mark on dipstick is

reached. Do not overfill.

• For cold weather operation you should

change oil for easier starting (See the

oil viscosity chart in the Maintenance section of this manual).

• To change engine oil, see the Mainte-

nance section in this manual.

ADD GASOLINE

• Fill fuel tank to bottom of filler neck. Do not overfill. Use fresh, clean, regular

unleaded gasoline with a minimum of 87 octane. (Use of leaded gasoline will increase carbon and lead oxide deposits and reduce valve life). Do not mix oil with gasoline. Purchase fuel in quan- tities that can be used within 30 days to

assure fuel freshness.

_CAUTION: Wipe off any spilled oil or fuel. Do not store, spill or use gasoline

near an open flame. IMPORTANT: When operating in temper-

atures below32°F(0°C), use fresh, clean winter grade gasoline to help insure good cold weather starting.

CAUTION: Alcohol blended fuels (called

gasohol or using ethanol or methanol) can

attract moisture which leads to separa- tion and formation of acids during storage.

Acidic gas can damage the fuel system

of an engine while in storage. To avoid engine problems, the fuel system should

be emptied before storage of 30 days

or longer. Drain the gas tank, start the engine and let it run until the fuel lines

and carburetor are empty. Use fresh fuel

next season. See Storage Instructions for

additional information. Never use engine

or carburetor cleaner products in the fuel tank or permanent damage may occur.

TO START ENGINE

When starting the engine for the first time

or if the engine has run out of fuel, it will

take extra cranking time to move fuel from

the tank to the engine.

1. Sit on seat in operating position, depress clutch/brake pedal and set

parking brake.

2. Place gear shift lever in neutral (N) position.

3. Move attachment clutch to disengaged position.

4. Move throttle control to choke position.

NOTE: Before starting, read the warm and cold starting procedures below.

5. Insert key into ignition and turn key clockwise to start position and release

key as soon as engine starts. Do

not run starter continuously for more than fifteen seconds per minute. If the engine does not start after several attempts, move throttle control to fast

position, wait a few minutes and try again. If engine still does not start,

move the throttle control back to the choke position and retry.

WARM WEATHER STARTING (50 ° F and above)

6. When engine starts, move the throttle control to the fast position.

• The attachments and ground drive can

now be used. If the engine does not accept the load, restart the engine and allow it to warm up for one minute using

the choke as described above.

COLD WEATHER STARTING ( 50 ° F and

below)

6. When engine starts, leave throttle control in choke position until engine warms up and begins to run roughly. Once rough running begins, imme- diately move the throttle control to the fast position. Engine warm-up may

take from several seconds to several

minutes (the colder the temperature,

the longer the warm-up).

• The attachments can also be used dur-

ing the engine warm-up period.

NOTE: If at a high altitude (above 3000 feet) or in cold temperatures (below 32 F) the carburetor fuel mixture may need to

be adjusted for best engine performance

(see "TO ADJUST CARBURETOR" in the Service and Adjustments section of this

manual).

MOWING TIPS

• Mower should be properly leveled for best mowing performance. See "TO

LEVEL MOWER HOUSING" in the Service and Adjustments section of this

manual.

• The left hand side of mower should be used for trimming.

• Drive so that clippings are discharged onto the area that has already been cut. Have the cut area to the right of

the tractor. This will result in a more even distribution of clippings and more

uniform cutting.

• When mowing large areas, start by turning to the right so that clippings will discharge away from shrubs, fences, driveways, etc. After one or two rounds, mow in the opposite direction making

left hand turns until finished.

• If grass is extremely tall, it should be mowed twice to reduce load and pos- sible fire hazard from dried clippings. Make first cut relatively high; the second

to the desired height.

• Do not mow grass when it is wet.

Wet grass will plug mower and leave

undesirable clumps. Allow grass to dry before mowing.

• Always operate engine at full throttle

when mowing to assure better mowing

performance and proper discharge of material. Regulate ground speed by selecting a low enough gear to give the mower cutting performance as well as

the quality of cut desired.

• When operating attachments, select a ground speed that will suit the terrain and give best performance of the at-

tachment being used.

(

00272

MAINTENANCE SCHEDULE _____

FILL IN DATES /_/@_/_-_,_" AS YOU COMPLETE /_'_ _'_ _.Oq'_ "

BE OLARSERV,CE OATES

°;:::kk:ir::2e:i°°

Check Operator Presence and

T Interlock Systems

R Check for Loose Fasteners If I_s

A Sharpen/Replace Mower Blades 1_3

C Lubrication Chart If I_

0 Check Battery Level _4

R Clean Battery and Terminals _ If

Check Transaxle Cooling v'

Check V-Belts I_ Check Engine Oil Level I_

Change Engine Oil (with oil filter) 1_1,2

E Change Engine Oil (without oil filter) _1,2

N Clean Air Filter 1_2 G Clean Air Screen _2

Ni Inspect Muffler/Spark

E Replace Oil Filter (If equipped) _1,2

Clean Engine Cooling Fins I_ 2 Replace Spark Plug I_ I_ Replace Air Filter Paper Cartridge _2

Replace Fuel Filter

1 - Change more often when operating under a heavy load or

in high ambient temperatures,

2 - Service more often when operating in dirty or dusty conditions,

GENERAL RECOMMENDATIONS

The warranty on this tractor does not cover items that have been subjected to

operator abuse or negligence. To receive full value from the warranty, operator

must maintain tractor as instructed in this manual.

Some adjustments will need to be made periodically to properly maintain your

tractor. At least once a season, check to see if

you should make any of the adjustments

described in the Service and Adjustments section of this manual.

• At least once a year you should replace the spark plug, clean or replace air filter,

and check blades and belts for wear. A new spark plug and clean air filter

assure proper air-fuel mixture and help your engine run better and last longer.

BEFORE EACH USE

1. Check engine oil level.

2. Check brake operation.

3. Check tire pressure.

4. Check operator presence and

interlock systems for proper operation.

5. Check for loose fasteners.

Arrester

3 - Replace blades more often when mowing in sandy soil. 4 - Not required if equipped with maintenance-free battery. 5 - Tighten front axle pivot bolt to 35 ft,-Ibs, maximum,

Do not overtighten.

LUBRICATION CHART

@ S_ Zerk

@Front Wheel ,-

Bearing

Zerk

@Engine .

_SAE 30 or 10w30 Motor Oil @General Purpose Grease

@Refer to Maintenance "ENGINE" Section

IMPORTANT: Do not oil or grease the pivot points which have special nylon bearings. Viscous lubricants will attract

dust and dirt that will shorten the life of the self-lubricating bearings. If you feel

they must be lubricated, use only a dry,

powdered graphite type lubricant sparingly.

-- @ Spindle Zerk

@Front Wheel

Bearing Zerk

+ 39 hidden pages