Craftsman 917276683, 917276682, 917276681, 917276680 Owner’s Manual

Operator's Manual

CRRFTSMIIN°

LAWN TRACTOR

24.0 HP, 42" Mower

Electric Start

Automatic Transmission

Model No.

917.276680 \ 276681 276682 \ 276683

• Espahol, p. 33

This product has a low emission engine which operates

_]_ differently from previously built engines. Before start the

engine, read and understand this Owner's Manual.

IMPORTANT:

Read and follow all Safety Rules and Instructions before

operating this equipment.

SEARS, ROEBUCK AND CO., HOFFMAN ESTATES, IL 60179 U.S.A.

Visit our Craftsman website:www.sears.com/craftsman

For answers to your questions

about this product, Call:

1-800-659-5917

Sears Craftsman Help Line

5 am - 5 pm, Mon- Sat

you

Warranty ................................................ 2

Safety Rules .......................................... 3

Product Specifications ........................... 6

Assembly/Pre-Operation ....................... 7

Operation ............................................... 9

Maintenance Schedule ........................ 17

Maintenance ........................................ 17

Service and Adjustments ..................... 21

Storage ................................................ 28

Troubleshooting ................................... 29

Sears Service ........................ Back Cover

LIMITED WARRANTY ON CRAFTSMAN TRACTOR AND BATTERY

2-YEAR ON TRACTOR When used and maintained according to the operator's manual instructions, if this

tractor fails due to a defect in material or workmanship within two years from the date of

purchase, call 1-800-4-MY-HOME® to arrange for free repair. During the first 30 days of purchase, there will be no charge to service the product in

your home. For your convenience, in-home warranty service will still be available after the first 30 days of purchase, but a trip charge will apply. This charge will be waived if you transport the product to an authorized Craftsman drop-off location. For the nearest

authorized location, call 1-800-4-MY-HOME®.

Tractor warranty coverage does not include:

• Expendable items which become worn during normal use, including but not limited to blades, spark plugs, air cleaners, belts, and oil filters.

• Standard maintenance servicing, oil changes, or tune-ups.

• Tire replacement or repair caused by punctures from outside objects, such as nails, thorns, stumps, or glass.

• Repairs necessary because of operator abuse, including but not limited to damage caused by towing objects beyond the capability of the tractor, impacting objects that bend the frame or crankshaft, or over-speeding the engine.

• Repairs necessary because of operator negligence, including but not limited to electri- cal and mechanical damage caused by improper storage, failure to use the proper grade and amount of engine oil, failure to keep the deck clear of flammable debris, or failure to maintain the equipment according to the instructions contained in the operator's manual.

• Engine (fuel system) cleaning or repairs necessary because of fuel determined to be contaminated or oxidized (stale). In general, fuel should be used within 30 days of its

purchase date.

• Normal deterioration and wear of the exterior finishes, or product label replacement.

• The tractor battery, which is covered for only 90 days as stated below.

90-DAYS ON BATTERY

For ninety (90) days from the date of purchase, if the battery included with this tractor is defective in material or workmanship (our testing proves it will not hold a charge), it will

be replaced free of charge. During the first 30 days of purchase, there will be no charges to replace the battery in

your home. For your convenience, in-home warranty service will still be available after the first 30 days of purchase, but a trip charge will apply. This charge will be waived if

you transport the battery to an authorized Craftsman drop-off location. For the nearest

authorized location, call 1-800-4-MY-HOME®.

All tractor and battery warranty coverage is void if this product is used for commercial or

rental purposes.

This warranty applies only while this product is within the United States. This warranty gives you specific legal rights, and you may also have other rights, which

vary, from state to state. Sears, Roebuck and Co., Hoffman Estates, IL 60179

_,DANGER: This cutting machine is capable of amputating hands and feet and

throwing objects. Failure to observe the following safety instructions could result

in serious injury or death.

,_WARNING: In order to prevent ac-

cidental starting when setting up, trans- porting, adjusting or making repairs, always disconnect spark plug wire and place wire where it cannot contact spark plug.

,_I_WARNING: Do not coast down a hill in

neutral, you may lose control of the tractor.

_,WARNING: Tow only the attachments

that are recommended by and comply with specifications of the manufacturer of your tractor. Use common sense when towing. Operate only at the lowest possible speed when on a slope. Too heavy of a load, while on a slope, is dangerous. Tires can lose traction with the ground and cause

you to lose control of your tractor. _,WARNING: Engine exhaust, some of

its constituents, and certain vehicle com- ponents contain or emit chemicals known

to the State of California to cause cancer and birth defects or other reproductive

harm.

_,WARNING: Battery posts, terminals

and related accessories contain lead and lead compounds, chemicals known to the

State of California to cause cancer and birth defects or other reproductive harm.

Wash hands after handling.

I. GENERAL OPERATION

• Read, understand, and follow all instructions on the machine and in the

manual before starting.

• Do not put hands or feet near rotating parts or under the machine. Keep clear of the discharge opening at all times.

• Only allow responsible adults, who are familiar with the instructions, to operate

the machine.

• Clear the area of objects such as rocks, toys, wire, etc., which could be

picked up and thrown by the blades.

• Be sure the area is clear of bystand- ers before operating. Stop machine if

anyone enters the area.

• Never carry passengers.

• Do not mow in reverse unless abso- lutely necessary. Always look down

and behind before and while backing.

• Never direct discharged material toward anyone. Avoid discharging

material against a wall or obstruction. Material may ricochet back toward the

operator. Stop the blades when cross-

ing gravel surfaces.

• Do not operate machine without the entire grass catcher, discharge guard, or other safety devices in place and working.

• Slow down before turning.

• Never leave a running machine

unattended. Always turn off blades,

set parking brake, stop engine, and

remove keys before dismounting.

• Disengage blades when not mowing. Shut off engine and wait for all parts to

come to a complete stop before clean-

ing the machine, removing the grass catcher, or unclogging the discharge guard.

• Operate machine only in daylight or good artificial light.

• Do not operate the machine while

under the influence of alcohol or drugs.

• Watch for traffic when operating near or crossing roadways.

• Use extra care when loading or unload-

ing the machine into a trailer or truck.

• Always wear eye protection when oper- ating machine.

• Data indicates that operators, age 60 years and above, are involved in a

large percentage of riding mower-re- lated injuries. These operators should

evaluate their ability to operate the

riding mower safely enough to protect

themselves and others from serious

injury.

• Follow the manufacturer's recommen- dation for wheel weights or counter-

weights.

• Keep machine free of grass, leaves or other debris build-up which can touch hot exhaust / engine parts and

burn. Do not allow the mower to plow leaves or other debris which can cause

build-up to occur. Clean any oil or fuel

spillage before operating or storing the

machine. Allow machine to cool before

storage.

I1. SLOPE OPERATION Slopes are a major factor related to loss of

control and tip-over accidents, which can

result in severe injury or death. Opera-

tion on all slopes requires extra caution. If you cannot back up the slope or if you feel

uneasy on it, do not mow it.

• Mow up and down slopes, not across.

• Watch for holes, ruts, bumps, rocks, or other hidden objects. Uneven terrain

could overturn the machine. Tall grass can hide obstacles.

• Choose a low ground speed so that

you will not have to stop or shift while

on the slope.

• Do not mow on wet grass. Tires may lose traction.

Always keep the machine in gear when

going down slopes. Do not shift to neutral and coast downhill.

• Avoid starting, stopping, or turning on a slope. If the tires lose traction, dis-

engage the blades and proceed slowly

straight down the slope.

• Keep all movement on the slopes slow and gradual. Do not make sudden

changes in speed or direction, which could cause the machine to roll over.

• Use extra care while operating ma-

chine with grass catchers or other at- tachments; they can affect the stability

of the machine. Do no use on steep slopes.

• Do not try to stabilize the machine by putting your foot on the ground.

• Do not mow near drop-offs, ditches, or embankments. The machine could

suddenly roll over if a wheel is over the

edge or if the edge caves in.

II1. CHILDREN

Tragic accidents can occur if the operator

is not alert to the presence of children. Children are often attracted to the machine

and the mowing activity. Never assume

that children will remain where you last

saw them.

• Keep children out of the mowing area and in the watchful care of a respon- sible adult other than the operator.

• Be alert and turn machine off if a child

enters the area.

• Before and while backing, look behind and down for small children.

• Never carry children, even with the blades shut off. They may fall off and be seriously injured or interfere with safe machine operation. Children who have been given rides in the past may suddenly appear in the mowing area

for another ride and be run over or

backed over by the machine.

• Never allow children to operate the machine.

• Use extra care when approaching blind

corners, shrubs, trees, or other objects that may block your view of a child.

IV. TOWING

• Tow only with a machine that has a hitch designed for towing. Do not at-

tach towed equipment except at the

hitch point.

• Follow the manufacturer's recom- mendation for weight limits for towed

equipment and towing on slopes.

• Never allow children or others in or on

towed equipment.

• On slopes, the weight of the towed

equipment may cause loss of traction

and loss of control.

• Travel slowly and allow extra distance

to stop.

V. SERVICE SAFE HANDLING OF GASOLINE

To avoid personal injury or property damage, use extreme care in handling gasoline. Gasoline is extremely flammable and the vapors are explosive.

• Extinguish all cigarettes, cigars, pipes, and other sources of ignition.

• Use only approved gasoline container.

• Never remove gas cap or add fuel with

the engine running. Allow engine to cool before refueling.

• Never fuel the machine indoors.

• Never store the machine or fuel con-

tainer where there is an open flame,

spark, or pilot light such as on a water heater or other appliances.

• Never fill containers inside a vehicle or on a truck or trailer bed with plastic

liner. Always place containers on the ground away from your vehicle when

filling.

• Remove gas-powered equipment from Check their proper operation regularly. the truck or trailer and refuel it on the Keep machine free of grass, leaves, or

ground. If this is not possible, then other debris build-up. Clean oil or fuel refuel such equipment with a portable spillage and remove any fuel-soaked

container,dispensernozzle.ratherthan from a gasoline • storing.debrisAllow machine to cool before

• Keep the nozzle in contact with the rim • If you strike a foreign object, stop and of the fuel tank or container opening at inspect the machine. Repair, if neces- all times until fueling is complete. Do sary, before restarting. not use a nozzle lock-open device. • Never make any adjustments or repairs

• If fuel is spilled on clothing, change with the engine running.

• clothing immediately. • Check grass catcher components and Never overfill fuel tank. Replace gas the discharge guard frequently and

cap and tighten securely, replace with manufacturer's recom-

GENERAL SERVICE mended parts, when necessary.

Never operate machine in a closed blade or wear gloves, and use extra area. caution when servicing them.

• Keep all nuts and bolts tight to be sure • Check brake operation frequently. Ad- the equipment is in safe working condi- just and service as required. tion. • Maintain or replace safety and instruc-

• Never tamper with safety devices, tion labels, as necessary.

• Be sure the area is clear of bystand- ers before operating. Stop machine if anyone enters the area.

• Never carry passengers.

• Do not mow in reverse unless abso- lutely necessary. Always look down

and behind before and while backing.

• Never carry children, even with the blades shut off. They may fall off and

be seriously injured or interfere with safe machine operation. Children who

have been given rides in the past may suddenly appear in the mowing area

for another ride and be run over or backed over by the machine.

• Keep children out of the mowing area and in the watchful care of a respon- sible adult other than the operator.

• Be alert and turn machine off if a child enters the area.

• Mower blades are sharp. Wrap the

• Before and while backing, look behind and down for small children.

• Mow up and down slopes (15 ° Max),

not across.

• Choose a low ground speed so that you will not have to stop or shift while on the slope.

• Avoid starting, stopping, or turning on a slope. If the tires lose traction, dis- engage the blades and proceed slowly straight down the slope.

• If machine stops while going uphill, disengage blades, shift into reverse and back down slowly.

• Do not turn on slopes unless neces- sary, and then, turn slowly and gradu- ally downhill, if possible.

PRODUCT SPECIFICATIONS

Gasoline Capacity 3.0 Gallons and Type: Unleaded Regular

Oil Type SAE 30 (above (API- SG-SL): 32°F)

SAE 5W30 (below 32°F

Oil Capacity: W/Filter: 64 oz.

W/O Filter: 60 oz.

Spark Plug: Champion QC12YC (Gap: .030")

Ground Speed Forward: 0-5.5

Reverse: 0-2.4

Charging System: 16 Amps @ 3600 RPIV Battery: Amp/Hr: 35

Min. CCA: 280

Case size: U1R

Blade Bolt Torque: 45-55 Ft. Lbs.

CONGRATULATIONS on your purchase of a new tractor. It has been designed,

engineered and manufactured to give you the best possible dependability and

performance. Should you experience any problem you

cannot easily remedy, please contact a

Sears or other qualified service center.

We have competent, well-trained repre-

sentatives and the proper tools to service or repair this tractor.

Please read and retain this manual. The instructions will enable you to assemble

and maintain your tractor properly. Always observe the "SAFETY RULES".

CUSTOMER RESPONSIBILITIES

• Read and observe the safety rules.

• Follow a regular schedule in main- taining, caring for and using your tractor.

• Follow the instructions under "Mainte- nance" and "Storage" sections of this

owner's manual.

,_WARNING: This tractor is equipped with an internal combustion engine and

should not be used on or near any unim- proved forest-covered, brush-covered or

grass-covered land unless the engine's

exhaust system is equipped with a spark

arrester meeting applicable local or state laws (if any). If a spark arrester is used, it should be maintained in effective working

order by the operator.

In the state of California the above is re-

quired by law (Section 4442 of the Califor- nia Public Resources Code). Other states

may have similar laws. Federal laws apply on federal lands. A spark arrester for the

muffler is available through your nearest Sears service center (See REPAIR PARTS

manual).

REPAIR PROTECTION

AGREEMENTS

Congratulations on making a smart pur- chase. Your new Craftsman@ product is designed and manufactured for years of dependable operation. But like all products, it may require repair from time to time. That's when having a Repair Protection Agreement can save you money and aggravation.

Purchase a Repair Protection Agreement now and protect yourself from unexpected hassle and expense.

Here's what's included in the Agreement:

• Expert service by our 12,000 profe-

sional repair specialists.

• Unlimited service and no charge for

parts and labor on all covered repairs.

• Product replacement if your covered

product can't be fixed.

• Discount of 10% from regular price of

service and service-related parts not covered by the agreement; also, 10%

off regular price of preventive mainte-

nance check.

• Fast help by phone- phone sup-

port from a Sears representative on products requiring in-home repair, plus

convenient repair scheduling.

Once you purchase the Agreement, a simple phone call is all that it takes for you

to schedule service. You can call anytime day or night, or schedule a service ap- pointment online. Sears has over 12,000 professional repair specialists, who have access to over 4.5 million quality parts and accessories. That's the kind of professionalism you can count on to help prolong the life of your new purchase for years to come. Purchase your Repair Protection Agreement today! Some limitations and exclusions apply. For prices and additional information

call 1-800-827-6655. SEARS INSTALLATION SERVICE

For Sears professional installation of home appliances, garage door openers, water heaters, and other major home items, in

the U.S.A. call 1-800-4-MY-HOME®

Slope Sheet

Keys

(2) Keys

Your new tractor has been assembled at the factory with the exception of those parts left

unassembled for shipping purposes.

When right or left hand is mentioned in this manual, it means, from your point of view, when you are in the operating posi- tion (seated behind the steering wheel).

TO REMOVE TRACTOR FROM

CARTON UNPACK CARTON

1. Cut along dashed lines on all four pan- els of carton. Remove end panels and lay side panels flat.

2. Remove protective materials from trac- tor hood and grille.

IMPORTANT: Check for and remove any staples in skid that may puncture tires

where tractor is to roll off skid.

CHECK BATTERY

1. Lift hood to raised position. NOTE: If this battery is put into service after month and year indicated on label (L) (label is located between terminals)

charge battery for minimum of one hour at

6-10 amps. (See "BATTERY" in Mainte- nance section of this manual for charging instructions).

(1) Oil Drain Tube For Future Use

ADJUST SEAT

1. Sit in seat.

2. Lift up adjustment lever (A) and slide seat until a comfortable position is

reached which allows you to press

clutch/brake pedal all the way down.

3. Release lever to lock seat in position.

NOTE: You may now roll or drive your

tractor off the skid. Follow the appropriate

instruction below to remove the tractor

from the skid. jf_ WARNING: Before starting, read, un-

derstand and follow all instructions in the Operation section of this manual. Be sure

tractor is in a well-ventilated area. Be sure the area in front of tractor is clear of other

people and objects.

TO ROLL TRACTOR OFF SKID (See

Operation section for location and

function of controls)

1. Raise attachment lift lever to its high- est position.

2. Release parking brake by depressing brake pedal.

3. Place freewheel control in disengaged position to disengage transmission (See "TO TRANSPORT" in the Op-

eration section of this manual).

4. Rolltractorforwardoff skid.

5. Removebandingholdingthedeflector shield upagainsttractor.

TO DRIVE TRACTOR OFF SKID

(See Operation section for location

and function of controls)

1. Be sure all the above assembly steps have been completed.

2. Check engine oil level and fill fuel tank with gasoline.

3. Place freewheel control in "trans-

mission engaged" position (see "TO TRANSPORT" in Operation section of this manual).

4. Sit on seat in operating position, de- press brake pedal and set the parking

brake.

5. Raise attachment lift lever to its highest position.

6. Remove key from bag and start the

engine (see "TO START ENGINE" in the Operation section of this manual).

After engine has started, move throttle control to idle (slow) position.

7. Release parking brake.

8. Slowly depress forward drive pedal

and drive tractor off skid.

9. Apply brake to stop tractor and set parking brake.

10. Turn ignition key to "STOP" position.

Continue with the instructions that follow.

CHECK TIRE PRESSURE

The tires on your tractor were overinfiated

at the factory for shipping purposes. Cor- rect tire pressure is important for best

cutting performance.

• Reduce tire pressure to PSI shown on tires.

CHECK DECK LEVELNESS For best cutting results, mower hous-

ing should be properly leveled. See "TO LEVEL MOWER" in the Service and

Adjustments section of this manual.

CHECK FOR PROPER POSITION

OF ALL BELTS

See the figures that are shown for replac- ing motion and mower blade drive belts

in the Service and Adjustments section of this manual. Verify that the belts are routed correctly.

CHECK BRAKE SYSTEM After you learn how to operate your trac-

tor, check to see that the brake is operat- ing properly. See "TO CHECK BRAKE" in the Service and Adjustments section of

this manual.

,/'CHECKLIST

Before you operate your new tractor, we wish to assure that you receive the best

performance and satisfaction from this Quality Product.

Please review the following checklist: v" All assembly instructions have been

completed.

v" No remaining loose parts in carton. v" Battery is properly prepared and

charged.

v" Seat is adjusted comfortably and tight-

ened securely.

v" All tires are properly inflated. (For ship-

ping purposes, the tires were overin-

flated at the factory).

v" Be sure mower deck is properly leveled

side-to-side/front-to-rear for best cutting results. (Tires must be properly inflated

for leveling).

v" Check mower and drive belts. Be sure

they are routed properly around pulleys

and inside all belt keepers.

v" Check wiring. See that all connections

are still secure and wires are properly

clamped.

v" Before driving tractor, be sure freewheel

control is in "transmission engaged"

position (see "TO TRANSPORT" in the Operation section of this manual).

While learning how to use your tractor, pay extra attention to the following important

items:

v" Engine oil is at proper level. v" Fuel tank is filled with fresh, clean, regu-

lar unleaded gasoline.

v" Become familiar with all controls, their

location and function. Operate them before you start the engine.

v" Be sure brake system is in safe operat-

ing condition.

v" Be sure Operator Presence System

and Reverse Operation System (ROS) are working properly (See the Opera-

tion and Maintenance sections in this

manual).

v" It is important to purge the transmission

before operating your tractor for the first

time. Follow proper starting and transmis-

sion purging instructions (See "TO START ENGINE" and "PURGE TRANSMISSION"

in the Operation section of this manual).

Thesesymbolsmayappearon yourtractor orin literaturesuppliedwiththe product.

Learnandunderstandtheir meaning.

R N H I\1

REVERSE NEUTRAL HIGH LOW CHOKE FAST SLOW

IGNITION SWITCH

ENGINE OFF REVERSE ENGINE ON ENGINE START PARKING BRAKE MOWER HEIGHT

OPERATION

SYSTEM (ROS)

, ®s x)o

REVERSELIGHTS ON FUEL BATTERY

FORWARD CRUISE CONTROL CLUTCH/BRAKE

®@@@@

ATTACHMENT ATTACHMENT

CLUTCH DISENGAGED CLUTCH ENGAGED

FREE WHEEL

(Automatic Models only)

Failure to follow instructions

could result in serious injury or death. The safety alert symbol is used to identify safety inform-

ation about hazards which can result in death, serious injury

and/or property damage.

DANGER, KEEP HANDS

AND FEET AWAY

DANGER indicates a hazard which, if not avoided,

will result in death or serious injury.

WARNING indicates a hazard which, if not avoided, could result in death or serious injury.

CAUTION indicates a hazard which, if not avoided,

might result in minor or moderate injury.

CAUTION when used without the alert symbol,

indicates a situation that could result in damage

to the tractor and/or engine.

HOT SURFACES indicates a hazard which,

,_l_llIII/£1il,,

if not avoided, could result in death, serious injury and/or property damage.

FIRE indicates a hazard which, if not avoided,

could result in death, serious injury and/or property damage.

KEEP AREA CLEAR SLOPE HAZARDS

(SEE SAFETY RULES SECTION)

MOWER LIFT

PEDAL

KNOW YOUR TRACTOR READ THIS OWNER'S MANUAL AND SAFETY RULES BEFORE OPERATING YOUR

TRACTOR

Compare the illustrations with your tractor to familiarize yourself with the locations of

various controls and adjustments. Save this manual for future reference.

Our tractors conform to the applicable safety standards of the

American National Standards Institute.

(A) ATTACHMENT LIFT LEVER - Used

to raise and lower the mower or other at-

tachments mounted to your tractor.

(B) BRAKE PEDAL - Used for braking the

tractor and starting the engine.

control engine speed.

(E) ATTACHMENT CLUTCH LEVER

- Used to engage the mower blades, or

other attachments mounted to your tractor. (F) IGNITION SWITCH - Used for starting

and stopping the engine. (G) REVERSE OPERATION SYSTEM (ROS) "ON" POSITION - Allows opera-

tion of mower or other powered attach-

ment while in reverse.

03108

(H) LIGHT SWITCH - Turns the head- lights on and off. (J) CRUISE CONTROL LEVER - Used to

set forward movement of tractor at desired speed without holding the forward drive

pedal. (K) FORWARD DRIVE PEDAL - Used for

forward movement of tractor. (L) REVERSE DRIVE PEDAL - Used for

reverse movement of tractor. (M) FREEWHEEL CONTROL - Disen-

gages transmission for pushing or slowly towing the tractor with the engine off.

(N) CHOKE CONTROL - Used when starting a cold engine.

(P) SERVICE REMINDER / HOUR METER

- Indicates when service is required for the engine and mower.

The operation of any tractor can result in foreign objects thrown into the eyes, which can result in severe eye damage. Always wear safety glasses

or eye shields while operating your tractor or performing any adjustments or repairs. We recommend standard safety glasses or a wide vision safety

mask worn over spectacles.

HOW TO USE YOUR TRACTOR

TO SET PARKING BRAKE

Your tractor is equipped with an operator

presence sensing switch. When engine is running, any attempt by the operator

to leave the seat without first setting the

parking brake will shut off the engine.

1. Depress brake pedal (B) all the way down and hold.

2. Pull parking brake lever (C) up and hold, release pressure from brake pedal (B), then release parking brake

lever. Pedal should remain in brake position. Make sure parking brake will

hold tractor secure.

ENGINE -

• Move throttle control (D) between half and full speed (fast) position.

NOTE: Failure to move throttle control between half and full speed (fast) posi-

tion, before stopping, may cause engine to "backfire".

• Turn ignition key (F) to "STOP" position and remove key. Always remove key

when leaving tractor to prevent unau- thorized use.

• Never use choke (N) to stop engine.

IMPORTANT: Leaving the ignition switch in any position other than "STOP" will cause the battery to discharge and go dead.

NOTE: Under certain conditions when

tractor is standing idle with the engine run-

ning, hot engine exhaust gases may cause

"browning" of grass. To eliminate this pos- sibility, always stop engine when stopping

tractor on grass areas. ,_CAUTION: Always stop tractor com-

pletely, as described above, before leaving

the operator's position.

STOPPING

MOWER BLADES -

• To stop mower blades, move attachment clutch lever in to disengaged position

(1"_1) Attachment (I'_) Disengaged

Clutch Position Engage Position

GROUND DRIVE -

• To stop ground drive, depress brake pedal all the way down.

TO USE CHOKE CONTROL (N)

Use choke control whenever you are start- ing a cold engine. Do not use to start a

warm engine.

• To engage choke control, pull knob out. Slowly push knob in to disengage.

TO MOVE FORWARD AND

BACKWARD

The direction and speed of movement is controlled by the forward and reverse drive

pedals.

1. Start tractor and release parking brake.

2. Slowly depress forward (K) or reverse

(L) drive pedal to begin movement.

Ground speed increases the further

down the pedal is depressed.

TO USECRUISECONTROL Thecruisecontrolfeaturecan beusedfor forwardtravelonly.

SYSTEMCHARACTERISTICS

Thecruisecontrolshouldonlybe used while mowingortransportingonrelatively

smooth,straightsurfaces.Otherconditions suchas trimmingat slowspeedsmay

causethe cruisecontroltodisengage.Do

notusethecruisecontrolon slopes,rough

terrianor whiletrimmimgorturning.

• Withforwarddrivepedal (K) depressed todesiredspeed,pullcruisecontrol lever(J) up andholdwhileliftingyour footoffthe pedal,then releasethelever.

Todisengagethecruisecontrol,depress the brakepedalor taponforwarddrive

pedal.

TOADJUSTMOWERCUTTINGHEIGHT Thepositionofthe attachmentlift lever(A)

determinesthecuttingheight.

• Theaveragelawnshouldbecutto ap- proximately2-1/2inchesduringthecool seasonandtoover3 inchesduringhot

months.Forhealthierandbetterlook- inglawns,mowoftenandaftermoderate

growth.

• Forbestcuttingperformance,grassover 6inchesin height shouldbe mowed

twice. Makethe firstcut relativelyhigh; the secondto desiredheight.

TOADJUSTGAUGEWHEELS Gaugewheels are properlyadjusted

whenthey are slightlyoff the groundwhen moweris atthe desiredcuttingheightin operatingposition.Gaugewheelsthen keepthe deckin properpositionto help preventscalpingin mostterrainconditions. NOTE:Adjust gaugewheelswithtractor

on aflat levelsurface.

1. Adjustmowerto desiredcuttingheight (See"TOADJUSTMOWERCUTTING HEIGHT"inthis sectionof manual).

2. With mowerin desiredheightof cut position,gaugewheelsshouldbe

assembledsotheyareslightly offthe ground.Installgaugewheelin appro-

priatehole.Tightensecurely.

3. Repeatforall,installinggaugewheelin

sameadjustmenthole.

• Putattachmentlift leverin desiredcut- ting heightslot.

• Slide pointertab (T)to desiredcutting heightas a reminderfor nexttimeyou

mow.

The cutting height range is approxi-

mately 1" to 4". The heights are mea- sured from the ground to the blade tip with

the engine not running. These heights

are approximate and may vary depending upon soil conditions, height of grass and

types of grass being mowed.

TO OPERATE MOWER Your tractor is equipped with an operator

presence sensing switch. Any attempt by the operator to leave the seat with the

engine running and the attachment clutch engaged will shut off the engine. You must

remain fully and centrally positioned in the seat to prevent the engine from hesitating or cutting off when operating your equip- ment on rough, rolling terrain or hills.

1. Select desired height of cut with at- tachment lift lever.

2. Start mower blades by engaging at- tachment clutch control.

TO STOP MOWER BLADES - disengage attachment clutch control.

CAUTION: Do not operatethe mower

withouteitherthe entiregrasscatcher, on mowerssoequipped,or the deflector shield(S)in place.

REVERSE OPERATION SYSTEM (ROS)

Your tractor is equipped with a Reverse

Operation System (ROS). Any attempt by

the operator to travel in the reverse direc- tion with the attachment clutch engaged

will shut off the engine unless ignition key

is placed in the ROS "ON" position.

AI_WARNING: Backing up with the at- tachment clutch engaged while mowing

is strongly discouraged. Turning the ROS "ON", to allow reverse operation with the

attachment clutch engaged, should only be done when the operator decides it is

necessary to reposition the machine with

the attachment engaged. Do not mow in

reverse unless absolutely necessary. USING THE REVERSE OPERATION

SYSTEM - Only use if you are certain no children or

other bystanders will enter the mowing area.

1. Depress brake pedal all the way down.

2. With engine running, turn ignition key counterclockwise to ROS "ON" posi-

tion.

3. Look down and behind before and while backing.

4. Slowly depress reverse drive pedal to start movement.

5. When use of the ROS is no longer needed, turn the ignition key clockwise to engine "ON" position.

ROS "ON" Position

Engine "ON" Position (Normal Operating)

TO OPERATE ON HILLS

,I_WARNING: Do not drive up or down

hills with slopes greater than 15 ° and do not drive across any slope. Use the slope

guide provided at the back of this manual.

• Choose the slowest speed before start- ing up or down hills.

• Avoid stopping or changing speed on hills.

• If stopping is absolutely necessary, push brake pedal quickly to brake position and engage parking brake.

• To restart movement, slowly release parking brake and brake pedal.

• Slowly depress appropriate drive pedal

to slowest setting.

• Make all turns slowly.

TO TRANSPORT

When pushing or towing your tractor, be sure to disengage transmission by placing freewheel control in freewheeling position.

Freewheel control is located at the rear

drawbar of tractor.

1. Raise attachment lift lever to its highest position.

2. Pull freewheel control out and into the slot and release so it is held in the disengaged position.

• Do not push or tow tractor at more than

two (2) MPH.

• To re-engage transmission, reverse

above procedure.

Transmission Engaged

Transmission Disengaged

NOTE: To protect hood from damage when

transporting your tractor on a truck or a trailer, be sure hood is closed and secured

to tractor. Use an appropriate means of tying hood to tractor (rope, cord, etc.).

TOWING CARTS AND OTHER ATTACH-

MENTS

Tow only the attachments that are recom-

mended by and comply with specifications of the manufacturer of your tractor. Use

common sense when towing. Too heavy

of a load, while on a slope, is dangerous.

Tires can lose traction with the ground and cause you to lose control of your tractor.

SERVICE REMINDER/HOUR METER

Service reminder shows the total number of hours the engine has run and flashes to

indicate that the engine or mower needs servicing. When service is required, the

service reminder will flash for two hours.

To service engine and mower, see the

Maintenance section of this manual. NOTE: Service reminder runs when the

ignition key is in any position but "STOP". For accurate reading, be sure key remains

in the "STOP" position when engine is not running.

BEFORE STARTING THE ENGINE CHECK ENGINE OIL LEVEL

The engine in your tractor has been

shipped, from the factory, already filled

with summer weight oil.

1. Check engine oil with tractor on level ground.

2. Remove oil fill cap/dipstick and wipe clean, reinsert the dipstick and screw cap tight, wait for a few seconds, re-

move and read oil level. If necessary, add oil until "FULl" mark on dipstick is

reached. Do not overfill.

• For cold weather operation you should

change oil for easier starting (See the oil viscosity chart in the Maintenance section of this manual).

• To change engine oil, see the Mainte-

nance section in this manual.

ADD GASOLINE

• Fill fuel tank to bottom of filler neck. Do

not overfill. Use fresh, clean, regular unleaded gasoline with a minimum of 87 octane. (Use of leaded gasoline will increase carbon and lead oxide deposits and reduce valve life). Do not mix oil

with gasoline. Purchase fuel in quan- tities that can be used within 30 days to

assure fuel freshness. _;LCAUTION: Wipe off any spilled oil or fuel. Do not store, spill or use gasoline

near an open flame. IMPORTANT: When operating in temper-

atures below32°F(0°C), use fresh, clean winter grade gasoline to help insure good cold weather starting.

CAUTION: Alcohol blended fuels (called gasohol or using ethanol or methanol) can

attract moisture which leads to separa- tion and formation of acids during storage. Acidic gas can damage the fuel system

of an engine while in storage. To avoid engine problems, the fuel system should

be emptied before storage of 30 days or longer. Drain the gas tank, start the engine and let it run until the fuel lines

and carburetor are empty. Use fresh fuel next season. See Storage Instructions for

additional information. Never use engine or carburetor cleaner products in the fuel tank or permanent damage may occur.

TO START ENGINE When starting the engine for the first time

or if the engine has run out of fuel, it will take extra cranking time to move fuel from

the tank to the engine.

1. Be sure freewheel control is in the transmission engaged position.

2. Sit on seat in operating position, depress brake pedal and set parking

brake.

3. Move attachment clutch to disengaged position.

4. Move throttle control to fast position

5. Pull choke control out for a cold engine start attempt. For a warm engine start attempt the choke control may not be

needed.

NOTE: Before starting, read the warm and cold starting procedures below.

6. Insert key into ignition and turn key clockwise to start position and release key as soon as engine starts. Do not run starter continuously for more than fifteen seconds per minute. If the engine does not start after several attempts, push choke control in, wait a few minutes and try again. If engine still does not start, pull the choke con- trol out and retry.

WARM WEATHER STARTING (50 ° F and above)

7. When engine starts, slowly push choke control in until the engine begins to run smoothly. If the engine starts to run roughly, pull the choke control out slightly for a few seconds and then continue to push the control in slowly.

• The attachments and ground drive can

now be used. If the engine does not accept the load, restart the engine and allow it to warm up for one minute using

the choke as described above.

COLD WEATHER STARTING (50 ° F and below)

7. When engine starts, slowly push choke control in until the engine begins to run smoothly. Continue to push the choke control in small steps allowing the en- gine to accept small changes in speed and load, until the choke control is fully in. If the engine starts to run roughly, pull the choke control out slightly for a few seconds and then continue to push the control in slowly. This may require an engine warm-up period from several seconds to several minutes, depending on the temperature.

AUTOMATIC TRANSMISSION WARM UP

Before driving the unit in cold weather,

the transmission should be warmed up as follows:

1. Be sure the tractor is on level ground.

2. Release the parking brake and let the brake slowly return to operating posi- tion.

3. Allow one minute for transmission to warm up. This can be done during the

engine warm up period.

• The attachments can be used during the engine warm-up period after the

transmission has been warmed up and may require the choke control be pulled

out slightly.

NOTE: If at a high altitude (above 3000

feet) or in cold temperatures (below 32 F) the carburetor fuel mixture may need to

be adjusted for best engine performance (see "TO ADJUST CARBURETOR" in the

Service and Adjustments section of this manual).

2. Disengage transmission by placing freewheel control in disengaged posi- tion (See "TO TRANSPORT" in this section of manual).

3. Sitting in the tractor seat, start engine. After the engine is running, move throttle control to slow position. Disen-

,_gage parking brake.

AUTION: At any time, during step

4, there may be movement of the drive wheels.

4. Depress forward drive pedal to full forward position and hold for five (5) seconds and release pedal. Depress

reverse drive pedal to full reverse posi-

tion and hold for five (5) seconds and

release pedal. Repeat this procedure

three (3) times.

5. Shutoff engine and set parking brake.

6. Engage transmission by placing free- wheel control in engaged position (See "TO TRANSPORT" in this section of

manual).

7. Sitting in the tractor seat, start engine. After the engine is running, move throttle control to half (1/2) speed.

Disengage parking brake.

8. Drive tractor forward for approximately five feet then backwards for five feet.

Repeat this driving procedure three

times.

Your transmission is now purged and now

ready for normal operation.

PURGE TRANSMISSION

,_CAUTION: Never engage or dis- engage freewheel lever while the engine

is running. To ensure proper operation and per- formance, it is recommended that the transmission be purged before operating tractor for the first time. This procedure will

remove any trapped air inside the trans-

mission which may have developed during

shipping of your tractor.

IMPORTANT: Should your transmission

require removal for service or replace-

ment, it should be purged after reinstall-

ation before operating the tractor.

1. Place tractor safely on a level surface

- that is clear of objects and open - with engine off and parking brake set.

MOWING TIPS

• Tire chains cannot be used when the

mower housing is attached to tractor.

• Mower should be properly leveled for best mowing performance. See "TO

LEVEL MOWER HOUSING" in the Service and Adjustments section of this

manual.

• The left hand side of mower should be used for trimming.

• Drive so that clippings are discharged onto the area that has already been

cut. Have the cut area to the right of the tractor. This will result in a more

even distribution of clippings and more

uniform cutting.

• When mowing large areas, start by

turning to the right so that clippings will

discharge away from shrubs, fences, driveways, etc. After one or two rounds, mow in the opposite direction making

left hand turns until finished.

• If grass is extremely tall, it should be mowed twice to reduce load and pos- sible fire hazard from dried clippings. Make first cut relatively high; the second

to the desired height.

• Do not mow grass when it is wet.

Wet grass will plug mower and leave

undesirable clumps. Allow grass to dry before mowing.

• Always operate engine at full throttle

when mowing to assure better mowing

performance and proper discharge of material. Regulate ground speed by selecting a low enough speed to give

the mower cutting performance as well

as the quality of cut desired.

• When operating attachments, select a ground speed that will suit the terrain and give best performance of the at-

tachment being used.

MAINTENANCE BEFORE EVERY EVERY EVERY EVERY EVERY BEFORE

SCHEDULE EACH B 25 so loo SEASONSTORAQE

Check Brake Operation

Check Tire Pressure

USE HOURS HOURS HOURS HOURS

R Check Operator Presence & ROS Systern_

A Check for Loose Fasteners

C Check/Replace Mower Blades

T Lubrication Chart

0 Check Battery Level

Clean Battery and Terminals Check Transaxle Cooling

Check Mower Levelness Check V-Belts

Check Enqine Oil Level

Change Engine Oil (with oil filter)

Change Engine Oil (without oil filter

_ Clean Air Filter

G Clean Air Screen

I Inspect Muffler/SparkArrester

N Replace Oil Filter !If equipped)

E Clean Engine Cooling Fins

Replace Spark Plug Replace Air Filter Paper Cartridge

Re lace Fuel Filter .....

1 - Change more often when operating under a heavy load or

in high ambient temperatures.

2 - Service more often when operating in dirty or dusty conditions.

i/ v'

v'4

Vie1,2

Vlf1,2

3 - Replace blades more often when mowing in sandy soil. 4 - Not required if equipped with maintenance-free battery.

II' v"

VI_,2

GENERAL RECOMMENDATIONS

The warranty on this tractor does not cover items that have been subjected to

operator abuse or negligence. To receive

full value from the warranty, operator

must maintain tractor as instructed in this manual.

Some adjustments will need to be made periodically to properly maintain your

tractor. At least once a season, check to see if you should make any of the adjustments

described in the Service and Adjustments section of this manual.

• At least once a year you should replace the spark plug, clean or replace air filter,

and check blades and belts for wear. A new spark plug and clean air filter

assure proper air-fuel mixture and help

your engine run better and last longer.

BEFORE EACH USE

1. Check engine oil level.

2. Check brake operation.

3. Check tire pressure.

4. Check operator presence and

ROS systems for proper operation.

5. Check for loose fasteners.

LUBRICATION CHART

Spindle i Spindle

Zerk Zerk

Front Wheel

Bearing zerk

Steering

Sector Gear Teeth

_General Purpose Grease @Refer to Maintenance "ENGINE" Section

IMPORTANT: Do not oil or grease the pivot points which have special nylon

bearings. Viscous lubricants will attract dust and dirt that will shorten the life of the

self-lubricating bearings. If you feel they must be lubricated, use only a dry, pow-

dered graphite type lubricant sparingly.

Engine

TRACTOR Always observe safety rules when per-

forming any maintenance. BRAKE OPERATION

If tractor requires more than five (5) feet to stop at highest speed in highest gear on a

level, dry concrete or paved surface, then brake must be serviced. (See "TO CHECK BRAKE" in the Service and Adjustments

section of this manual).

TIRES

• Maintain proper air pressure in all tires (See PSI on tires).

• Keep tires free of gasoline, oil, or insect control chemicals which can harm rubber.

• Avoid stumps, stones, deep ruts, sharp objects and other hazards that may

cause tire damage.

NOTE: To seal tire punctures and prevent flat tires due to slow leaks, tire sealant

may be purchased from your local parts dealer. Tire sealant also prevents tire dry

rot and corrosion. OPERATOR PRESENCE SYSTEM AND

REVERSE OPERATION SYSTEM (ROS) Be sure operator presence and reverse

operation systems are working properly. If

your tractor does not function as de-

scribed, repair the problem immediately.

• The engine should not start unless the brake pedal is fully depressed, and the

attachment clutch control is in the disen- gaged position.

CHECK OPERATOR PRESENCE SYSTEM

• When the engine is running, any at- tempt by the operator to leave the seat

without first setting the parking brake should shut off the engine.

• When the engine is running and the attachment clutch is engaged, any at-

tempt by the operator to leave the seat should shut off the engine.

• The attachment clutch should never op- erate unless the operator is in the seat.

ROS "ON" Position Engine "ON" Position

(Normal Operating)

CHECK REVERSE OPERATION (ROS) SYSTEM

• When the engine is running with the ignition switch in the engine "ON" posi-

tion and the attachment clutch engaged,

any attempt by the operator to drive in reverse should shut off the engine.

• When the engine is running with the ignition switch in the ROS "ON" position

and the attachment clutch engaged, any attempt by the operator to drive in reverse should NOT shut off the engine.

BLADE CARE For best results mower blades must be

sharp. Replace worn, bent or damaged

blades.

CAUTION: Use only a replacement

blade approved by the manufacturer of

your tractor. Using a blade not approved

by the manufacturer of your tractor is hazardous, could damage your tractor and

void your warranty.

BLADE REMOVAL

1. Raise mower to highest position to al-

low access to blades.

NOTE: Protect your hands with gloves and/or wrap blade with heavy cloth.

2. Remove blade bolt by turning counter- clockwise.

3. Install new blade with stamped "GRASS SIDE" facing the ground.

IMPORTANT: To ensure proper assembly, center hole in blade must align with star

on mandrel assembly.

4. Install and tighten blade bolt securely (45-55 Ft. Lbs. torque).

IMPORTANT: Special blade bolt is heat treated.

Blade

Blade Bolt Assembly (Special)

Center Hole

BATTERY

Your tractor has a battery charging system which is sufficient for normal use. How-

ever, periodic charging of the battery with an automotive charger will extend its life.

• Keep battery and terminals clean.

• Keep battery bolts tight.

• Keep small vent holes open.

• Recharge at 6-10 amperes for 1 hour.

NOTE: The original equipment battery on your tractor is maintenance free. Do not

attempt to open or remove caps or covers. Adding or checking level of electrolyte is

not necessary.

TOCLEANBATTERYANDTERMINALS

Corrosionanddirt onthebatteryandtermi- nalscancausethebatteryto"leak"power.

1. DisconnectBLACKbatterycablefirst then RED battery cableand remove

batteryfrom tractor.

2. Rinsethe batterywith plainwaterand dry.

3. Cleanterminals andbatterycableends withwirebrushuntilbright.

4. Coatterminalswith greaseor petro- leumjelly.

5. Reinstallbattery(See"REPLACING BATTERY"inthe SERVICEANDAD-

JUSTMENTSsectionofthismanual).

TRANSAXLECOOLING Thetransmissionfanandcoolingfins

shouldbe keptcleanto assureproper

cooling.

Donot attemptto cleanfanor transmis- sionwhile engineis runningorwhilethe

transmissionis hot.Topreventpossible

damageto seals,do notuse high pressure

water orsteamto cleantransaxle.

• Inspectcoolingfan to besurefan blades

are intactandclean.

• Inspectcoolingfins fordirt, grassclip-

pingsandothermaterials. Toprevent damageto seals,do not usecom-

pressedair orhigh pressuresprayerto cleancooling fins.

TRANSAXLE PUMP FLUID

NOTE: Althoughmulti-viscosityoils

(5W30,10W30etc.) improvestartingin coldweather,they will resultin increased oilconsumptionwhen usedabove32°R Checkyourengineoil levelmorefrequent-

lyto avoidpossibleenginedamagefrom

runninglowonoil. Changethe oil after every50 hoursof op- erationor atleastoncea year if thetractor

isnotusedfor 50 hoursinoneyear. Checkthe crankcaseoil levelbeforestart-

ingthe engineand aftereach eight(8)

hoursof operation.Tightenoil fill cap/ dipsticksecurelyeach timeyoucheckthe

oil level. TOCHANGEENGINEOIL

Determinetemperaturerangeexpected

beforeoil change. All oilmustmeetAPI serviceclassificationSG-SL.

• Be suretractorisonlevelsurface.

• Oil will drainmorefreelywhenwarm.

• Catchoil ina suitablecontainer.

1. Removeoil fill cap/dipstick. Becareful notto allowdirt to entertheengine

whenchangingoil.

2. Removeyellowcapfromend ofdrain valveandinstallthe draintube ontothe

fitting.

Oil Drain Valve

The transaxle was sealed at the factory Closed

and fluid maintenance is not required for

the life of the transaxle. Should the trans- and

axle ever leak or require servicing, contact Position

your nearest Sears or other qualified

service center. V-BELTS

Check V-belts for deterioration and wear after 100 hours of operation and replace

if necessary. The belts are not adjustable. Replace belts if they begin to slip from wear.

ENGINE LUBRICATION

Only use high quality detergent oil rated with API service classification SG-SL.

Select the oil's SAE viscosity grade according to your expected operating temperature.

SAE VISCOSITY GRADES

F _20 0 30 32 40 60 80 100

c -_o -2o -1; ; 1'o _o _o 4o

TEMPERATURE RANGE ANTICIPATED BEFORE NEXT OIL CHANGE

oJ_ visccha[tle

Locked

Yellow Cap

3. Unlock drain valve by pushing inward slightly and turning counterclockwise.

4. To open, pull out on the drain valve.

5. After oil has drained completely, close and lock the drain valve by pushing

inward and turning clockwise until the pin is in the locked position as shown.

6. Remove the drain tube and replace the cap onto the end of the drain valve.

7. Refill engine with oil through oil fill dip- stick tube. Pour slowly. Do not overfill.

For approximate capacity see "PROD- UCT SPECIFICATIONS" section of this

manual.

Drain Tube

8. Use gauge on oil fill cap/dipstick for checking level. For accurate reading,

insert dipstick into the tube and push down firmly into place before removing. Keep oil up to, but not over, the "FULl" line on dipstick. Push dipstick down

firmly into the tube when finished.

ENGINE OIL FILTER Replace the engine oil filter every season

or every other oil change if the tractor is used more than 100 hours in one year. AIR FILTER

Your engine will not run properly using a

dirty air filter. Clean the foam pre-cleaner after every 25 hours of operation or every season. Service paper cartridge every 100 hours of operation or every season,

whichever occurs first.

Service air cleaner more often under dusty

conditions.

1. Remove cover.

TO SERVICE PRE-CLEANER

2. Wash it in liquid detergent and water.

3. Squeeze it dry in a clean cloth.

4. Saturate it in engine oil. Wrap it in clean, absorbent cloth and squeeze to

remove excess oil.

NOTE: If very dirty or damaged, replace pre-cleaner.

TO SERVICE CARTRIDGE

1. Clean cartridge by tapping gently on flat surface. If very dirty or damaged,

replace cartridge.

2. Reinstall precleaner cartridge, cover and secure.

IMPORTANT: Petroleum solvents, such as kerosene, are not to be used to clean

the cartridge. They may cause deterio-

ration of the cartridge. Do not oil cartridge. Do not use pressurized air to clean or dry

cartridge.

CLEAN AIR INTAKE/COOLING AREAS

To insure proper cooling, make sure the grass screen, cooling fins, and other exter-

nal surfaces of the engine are kept clean at all times.

Every 100 hours of operation (more often under extremely dusty, dirty conditions), remove the blower housing and other cool-

ing shrouds. Clean the cooling fins and external surfaces as necessary. Make sure

the cooling shrouds are reinstalled. NOTE: Operating the engine with a blocked grass screen, dirty or plugged

cooling fins, and/or cooling shrouds removed will cause engine damage due to

overheating.

MUFFLER

Inspect and replace corroded muffler and

spark arrester (if equipped) as it could cre- ate a fire hazard and/or damage.

SPARK PLUG(S) Replace spark plug(s) at the beginning

of each mowing season or after every

100 hours of operation, whichever occurs

first. Spark plug type and gap setting are shown in "PRODUCT SPECIFICATIONS"

section of this manual.

IN-LINE FUEL FILTER

The fuel filter should be replaced once each season. If fuel filter becomes

clogged, obstructing fuel flow to carbu- retor, replacement is required.

1. With engine cool, remove filter and plug fuel line sections.

2. Place new fuel filter in position in fuel line with arrow pointing towards carbu-

retor.

3. Be sure there are no fuel line leaks and clamps are properly positioned.

4. Immediately wipe up any spilled gaso- line.

Clamp

Cover

Cartridge

Foam

CLEAN AIR SCREEN

Air screen must be kept free of dirt and chaff to prevent engine damage from

overheating. Clean with a wire brush or

compressed air to remove dirt and stub-

born dried gum fibers.

CLEANING

• Clean engine, battery, seat, finish, etc.

of all foreign matter.

• Keep finished surfaces and wheels free

of all gasoline, oil, etc.

• Protect painted surfaces with auto-

motive type wax. We do not recommend using a garden hose or pressure washer to clean your tractor unless the engine and transmis- sion are covered to keep water out. Water in engine or transmission will shorten the useful life of your tractor. Use compressed air or a leaf blower to remove grass,

201eaves and trash from tractor and mower.

+ 44 hidden pages