Craftsman 917276360 Owner’s Manual

Owner's Manual

CRRFTSMRN°

j_]lI,

GARDEN TRACTOR

25.0 HE 48" Mower Electric Start

Automatic Transmission

Model No.

917.276360

This product has a low emission engine which operates

[_ from built Before start the

IMPORTANT:

Read and follow all Safety Rules and Instructions before

operating this equipment.

Sears, Roebuck and Co., Hoffman Estates, IL 60179 U.S.A.

Visit our Craftsman website:www.sears.com/craftsman

differently previously engines. you engine, read and understand this Owner's Manual.

For answers to your questions

about this product, Call:

1-800-659-5917

Sears Craftsman Help Line

5 am - 5 pm, Mon - Sat

Warranty................................................2

SafetyRules..........................................3

ProductSpecifications...........................6

Assembly/Pre-Operation.......................7

Operation...............................................9

MaintenanceSchedule........................16

LIMITEDWARRANTYONCRAFTSMANRIDINGEQUIPMENT Fortwo (2)yearsfromthedate ofpurchase,if this CraftsmanRidingEquipmentis

maintained,lubricatedandtuned upaccordingto the instructionsin the owner'smanual, Searswill repairor replacefreeof chargeany partsthat arefoundto be defectivein

materialorworkmanshipaccordingto theguidelinesofcoveragelistedbelow.Searswill alsoprovidefreelaborfortheseapplicablewarrantedpartsforthe twofullyears.During

thefirst 30 daysof purchase,therewill be nochargesto servicethe productat your

homefor issuescoveredbythis warranty.(Seeexclusionsbelow). Foryourconve- nience, INHOMEwarrantyservicewillstillbe availableafterthefirst 30 daysof pur-

chase,buta trip chargewillapply.Thischargewill bewaivedif the Craftsmanproductis

droppedoffat an authorizedSearslocation.Forthe nearestauthorizedSearslocation, pleasecall 1-800-4-MY-HOME®.Thiswarrantyapplies onlywhile this productiswithin

the UnitedStates. ThisWarrantydoesnotcover:

• Expendableitemswhich becomewornduring normaluse, includingbutnotlimitedto blades,spark plugs,air cleaners,belts,and oilfilters.

• StandardMaintenanceServicing,oil changes, or tune-ups.

• Tire replacementor repaircausedby puncturesfromoutsideobjects,suchasnails, thorns,stumps,or glass.

• Repairsnecessarybecauseof operatorabuse,includingbutnotlimitedto, damage causedby towingobjectsbeyondthecapabilityofthe ridingequipment,impacting objectsthat bendtheframeor crankshaft,or over-speedingtheengine.

• Repairsnecessarybecauseof operatornegligence,includingbutnotlimitedto,elec- tricaland mechanicaldamagecausedbyimproperstorage,failureto usethe proper gradeandamount ofengineoil,failureto keepthe deckclearof flammabledebris,

orfailureto maintainthe equipmentaccordingtothe instructionscontainedinthe owner'smanual.

• Engine(fuelsystem)cleaningor repairscausedbyfueldeterminedto becontami- natedor oxidized(stale). In general,fuelshould beused within30 daysof itspur-

chasedate.

• Normaldeteriorationand wearoftheexteriorfinishes,or productlabelreplacement.

• Ridingequipmentusedfor commercialor rentalpurposes.

LIMITEDWARRANTYON BATTERY Forninety(90) daysfromdate of purchase,if anybatteryincludedwith thisridingequip-

mentprovesdefectivein materialorworkmanshipandourtestingdeterminesthe battery

will notholda charge,Searswill replacethebattery atno charge. Duringthe first30

daysofpurchase,therewill be no chargesto replacethebatteryatyour HOME. After

thefirst 30 days,foryour convenience,IN-HOMEwarrantyservicewill stillbe avail-

ablebut atripchargewill apply. This chargewillbewaivedif the Craftsmanproductis droppedoff atan authorizedSearslocation.Forthe nearestauthorizedSearslocation, pleasecall 1-800-4-MY-HOME®.

Maintenance........................................16

ServiceandAdjustments.....................21

Storage................................................29

Troubleshooting...................................30

RepairParts.........................................34

SearsService........................BackCover

Thisbatterywarrantyappliesonlywhile thisproductiswithinthe UnitedStates. Thiswarrantygivesyouspecificlegalrights,andyoumayalsohave otherrights,which

vary,fromstateto state.

Sears,RoebuckandCo.,Dept.817WA,HoffmanEstates,IL 60179

IMPORTANT:This cuttingmachineiscapableofamputatinghandsandfeet andthrow- ingobjects.Failureto observethe followingsafety instructionscould resultinserious

injuryor death.

WARNING: Inorder to preventac-

cidentalstartingwhensetting up,trans-

porting,adjustingor makingrepairs, alwaysdisconnectsparkplugwire and placewirewhereitcannotcontactspark plug.

WARNING: Donot coastdown a

hillinneutral,you maylosecontrolofthe

tractor.

WARNING: Towonlytheattachments

that are recommendedbyand complywith

specificationsof themanufacturerof your

tractor.Usecommonsensewhentowing.

Operateonly at the lowestpossiblespeed whenon aslope. Tooheavyof a load, while on a slope,is dangerous.Tirescan

losetractionwiththe groundandcause you to losecontrol ofyour tractor.

WARNING:Engineexhaust, some

of its constituents, and certain vehicle components contain or emit chemicals

known to the State of California to cause cancer and birth defects or other reproduc-

tive harm.

WARNING: Battery posts, terminals

and related accessories contain lead and

lead compounds, chemicals known to the

State of California to cause cancer and

birth defects or other reproductive harm. Wash hands after handling.

I. GENERAL OPERATION

• Read, understand, and follow all

instructions on the machine and in the manual before starting.

• Do not put hands or feet near rotating

parts or under the machine. Keep clear of the discharge opening at all times.

• Only allow responsible adults, who are

familiar with the instructions, to operate the machine.

• Clear the area of objects such as

rocks, toys, wire, etc., which could be picked up and thrown by the blades.

• Be sure the area is clear of bystand-

ers before operating. Stop machine if anyone enters the area.

• Never carry passengers.

• Do not mow in reverse unless abso-

lutely necessary. Always look down and behind before and while backing.

• Never direct discharged material toward anyone. Avoid discharging

material against a wall or obstruction. Material may ricochet back toward the

operator. Stop the blades when cross-

ing gravel surfaces.

• Do not operate machine without the entire grass catcher, discharge guard, or other safety devices in place and working.

• Slow down before turning.

• Never leave a running machine

unattended. Always turn off blades,

set parking brake, stop engine, and

remove keys before dismounting.

• Disengage blades when not mowing. Shut off engine and wait for all parts to

come to a complete stop before clean-

ing the machine, removing the grass

catcher, or unclogging the discharge guard.

• Operate machine only in daylight or good artificial light.

• Do not operate the machine while

under the influence of alcohol or drugs.

• Watch for traffic when operating near or crossing roadways.

• Use extra care when loading or unload-

ing the machine into a trailer or truck.

• Always wear eye protection when oper- ating machine.

• Data indicates that operators, age 60 years and above, are involved in a

large percentage of riding mower-re- lated injuries. These operators should

evaluate their ability to operate the

riding mower safely enough to protect

themselves and others from serious

injury.

• Follow the manufacturer's recommen- dation for wheel weights or counter-

weights.

• Keep machine free of grass, leaves or other debris build-up which can touch

hot exhaust / engine parts and burn. Do not allow the mower deck to plow

leaves or other debris which can cause build-up to occur. Clean any oil or fuel

spillage before operating or storing the

machine. Allow machine to cool before

storage.

I1. SLOPE OPERATION

Slopes are a major factor related to loss of control and tip-over accidents, which can

result in severe injury or death. Opera- tion on all slopes requires extra caution. If you cannot back up the slope or if you feel

uneasy on it, do not mow it.

• Mow up and down slopes, not across.

• Watch for holes, ruts, bumps, rocks, or

other hidden objects. Uneven terrain could overturn the machine. Tall grass

can hide obstacles.

• Choose a low ground speed so that

you will not have to stop or shift while on the slope.

• Do not mow on wet grass. Tires may

lose traction.

Always keep the machine in gear when going down slopes. Do not shift to

neutral and coast downhill.

• Avoid starting, stopping, or turning on

a slope. If the tires lose traction, dis- engage the blades and proceed slowly straight down the slope.

• Keep all movement on the slopes slow

and gradual. Do not make sudden changes in speed or direction, which

could cause the machine to roll over.

• Use extra care while operating ma-

chine with grass catchers or other at- tachments; they can affect the stability

of the machine. Do no use on steep slopes.

• Do not try to stabilize the machine by

putting your foot on the ground.

• Do not mow near drop-offs, ditches,

or embankments. The machine could suddenly roll over if a wheel is over the

edge or if the edge caves in.

III, CHILDREN Tragic accidents can occur if the operator

is not alert to the presence of children. Children are often attracted to the machine

and the mowing activity. Never assume that children will remain where you last

saw them.

• Keep children out of the mowing area

and in the watchful care of a respon- sible adult other than the operator.

• Be alert and turn machine off if a child

enters the area.

• Before and while backing, look behind

and down for small children.

• Never carry children, even with the blades shut off. They may fall off and be seriously injured or interfere with

safe machine operation. Children who

have been given rides in the past may

suddenly appear in the mowing area for another ride and be run over or

backed over by the machine.

• Never allow children to operate the machine.

• Use extra care when approaching blind

corners, shrubs, trees, or other objects that may block your view of a child.

IV. TOWING

• Tow only with a machine that has a hitch designed for towing. Do not at-

tach towed equipment except at the

hitch point.

• Follow the manufacturer's recommen-

dation for weight limits for towed equip-

ment and towing on slopes.

• Never allow children or others in or on

towed equipment.

• On slopes, the weight of the towed

equipment may cause loss of traction and loss of control.

• Travel slowly and allow extra distance

to stop.

V. SERVICE SAFE HANDLING OF GASOLINE To avoid personal injury or property

damage, use extreme care in handling gasoline. Gasoline is extremely flammable and the vapors are explosive.

• Extinguish all cigarettes, cigars, pipes,

and other sources of ignition.

• Use only approved gasoline container.

• Never remove gas cap or add fuel with

the engine running. Allow engine to cool before refueling.

• Never fuel the machine indoors.

• Never store the machine or fuel con-

tainer where there is an open flame, spark, or pilot light such as on a water

heater or other appliances.

• Never fill containers inside a vehicle

or on a truck or trailer bed with plastic

liner. Always place containers on the

ground away from your vehicle when filling.

• Removegas-poweredequipmentfrom thetruck ortrailerandrefuel it onthe

ground.If thisisnot possible,then

refuelsuchequipment with a portable

container, rather than from a gasoline dispenser nozzle.

• Keep the nozzle in contact with the rim of the fuel tank or container opening at all times until fueling is complete. Do

not use a nozzle lock-open device.

• If fuel is spilled on clothing, change clothing immediately.

• Never overfill fuel tank. Replace gas cap and tighten securely.

GENERAL SERVICE

• Never operate machine in a closed area.

• Keep all nuts and bolts tight to be sure the equipment is in safe working condi-

tion.

• Never tamper with safety devices.

Check their proper operation regularly.

• Keep machine free of grass, leaves, or other debris build-up. Clean oil or fuel spillage and remove any fuel-soaked

debris. Allow machine to cool before storing.

• If you strike a foreign object, stop and inspect the machine. Repair, if neces- sary, before restarting.

• Never make any adjustments or repairs with the engine running.

• Check grass catcher components and the discharge guard frequently and

replace with manufacturer's recom- mended parts, when necessary.

• Mower blades are sharp. Wrap the blade or wear gloves, and use extra caution when servicing them.

• Check brake operation frequently. Ad-

just and service as required.

• Maintain or replace safety and instruc- tion labels, as necessary.

• Be sure the area is clear of bystand- ers before operating. Stop machine if

anyone enters the area.

• Never carry passengers.

• Do not mow in reverse unless abso-

lutely necessary. Always look down

and behind before and while backing.

• Never carry children, even with the

blades shut off. They may fall off and be seriously injured or interfere with

safe machine operation. Children who

have been given rides in the past may

suddenly appear in the mowing area for another ride and be run over or

backed over by the machine.

• Keep children out of the mowing area and in the watchful care of a respon- sible adult other than the operator.

• Be alert and turn machine off if a child enters the area.

• Before and while backing, look behind and down for small children.

• Mow up and down slopes (15 ° Max), not across.

• Choose a low ground speed so that

you will not have to stop or shift while

on the slope.

• Avoid starting, stopping, or turning on a slope. If the tires lose traction, dis-

engage the blades and proceed slowly straight down the slope.

• If machine stops while going uphill, disengage blades, shift into reverse and back down slowly.

• Do not turn on slopes unless neces- sary, and then, turn slowly and gradu- ally downhill, if possible.

PRODUCT SPECIFICATIONS

Gasoline 5.0 Gallons Capacity Unleaded

and Type: Regular Oil Type SAE 10W30

'API-SG-SL): (above 32°F)

SAE 5W-30 (below 32°F)

Oil Capacity: W/Filter: 4.0 Pints

W/O Filter: 3.5 Pints

Spark Plug: Champion RC12YC

'Gap: .030")

Ground Speed (MPH):

Forward: 0 - 5.8 Reverse: 0 - 2.1

Tire Pressure: Front: 14 PSI

Rear: 10PSI

Charging System: 15 AMPS @ 3600RPM

Battery: Amp/Hr: 35

Min. CCA: 280 Case size: U1R

Blade Bolt Torque: 45-55 Ft. Lbs.

CONGRATULATIONS on your purchase

of a new tractor. It has been designed, engineered and manufactured to give you the best possible dependability and

performance.

Should you experience any problem you cannot easily remedy, please contact a

Sears or other qualified service center. We have competent, well-trained techni-

cians and the proper tools to service or

repair this tractor.

Please read and retain this manual. The

instructions will enable you to assemble

and maintain your tractor properly. Always

observe the "SAFETY RULES".

CUSTOMER RESPONSIBILITIES

• Read and observe the safety rules.

• Follow a regular schedule in main-

taining, caring for and using your tractor.

• Follow the instructions under "Mainte-

nance" and "Storage" sections of this owner's manual.

_,WARNING: This tractor is equipped with an internal combustion engine and

should not be used on or near any unim-

proved forest-covered, brush-covered or

grass-covered land unless the engine's exhaust system is equipped with a spark

arrester meeting applicable local or state

laws (if any). If a spark arrester is used, it

should be maintained in effective working

order by the operator.

In the state of California the above is re-

quired by law (Section 4442 of the Califor- nia Public Resources Code). Other states may have similar laws. Federal laws apply on federal lands. A spark arrester for the muffler is available through your nearest Sears service center (See REPAIR PARTS section of this manual).

REPAIR PROTECTION

AGREEMENTS

Congratulations on making a smart pur- chase. Your new Craftsman® product is

designed and manufactured for years of dependable operation. But like all prod- ucts, it may require repair from time to time. That's when having a Repair Protec- tion Agreement can save you money and aggravation.

Purchase a Repair Protection Agreement now and protect yourself from unexpected hassle and expense.

Here's what's included in the Agreement:

• Expert service by our 12,000 profe-

sional repair specialists.

• Unlimited service and no charge for

parts and labor on all covered repairs.

• Product replacement if your covered

product can't be fixed.

• Discount of 10% from regular price of

service and service-related parts not covered by the agreement; also, 10% off regular price of preventive mainte-

nance check.

• Fast help by phone- phone support

from a Sears technician on products

requiring in-home repair, plus conve- nient repair scheduling.

Once you purchase the Agreement, a simple phone call is all that it takes for you

to schedule service. You can call anytime day or night, or schedule a service ap- pointment online. Sears has over 12,000 professional repair specialists, who have access to over 4.5 million quality parts and accessories. That's the kind of professionalism you can count on to help prolong the life of your new purchase for years to come. Purchase your Repair Protection Agreement today! Some limitations and exclusions apply. For prices and additional information

call 1-800-827-6655. SEARS INSTALLATION SERVICE

For Sears professional installation of home appliances, garage door openers, water heaters, and other major home items, in

the U.S.A. call 1-800-4-MY-HOME®

Keys Slope Sheet

(1) Oil Drain Tube

(2) Keys

Your new tractor has been assembled at the factory. When right or left hand is mentioned in

this manual, it means, from your point of view, when you are in the operating posi- tion (seated behind the steering wheel).

TO REMOVE TRACTOR FROM

CARTON UNPACK CARTON

1. Cut along dotted lines on all four pan- els of carton. Remove end panels and lay side panels flat.

2. Remove packing materials.

3. Remove protective materials from trac- tor hood and grille.

IMPORTANT: Check for and remove any staples in skid that may puncture tires

where tractor is to roll off skid.

ADJUST SEAT

1. Raise seat and loosen adjustment

2. Lower seat into operating position and

3. Slide seat until a comfortable position

4. Get off seat without moving its ad-

5. Raise seat and tighten adjustment

knobs.

sit in seat.

is reached which allows you to press

clutch/brake pedal all the way down.

justed position.

knob securely.

CHECK BATTERY

1. Lift hood to raised position.

NOTE: If this battery is put into service

after month and year indicated on label (label located between terminals) charge battery for minimum of one hour at 6-10 amps. (See "BATTERY" in Maintenance section of this manual for charging instruc-

tions).

. , _ Label

Adjustment

Knob

NOTE: You may now roll or drive your

tractor off the skid. Follow the appropriate

instruction below to remove the tractor

from the skid.

TO ROLL TRACTOR OFF SKID (See

Operation section for location and

function of controls)

1. Press lift lever plunger and raise attachment lift lever to its highest po-

sition.

2. Release parking brake by depressing brake pedal.

3. Place freewheel control in transmission

disengaged position (See "To Trans-

port" in the Operation section of this manual).

4. Roll tractor forward off skid.

TO DRIVE TRACTOR OFF SKID (See

Operation section for location and

_nction of controls)

WARNING: Before starting, read, un-

derstand and follow all instructions in the Operation section of this manual. Be sure

tractor is in a well-ventilated area. Be sure the area in front of tractor is clear of other

people and objects.

1. Be sure all the above assembly steps have been completed.

2. Check engine oil level and fill fuel tank with gasoline.

3. Place freewheel control in "trans- mission engaged" position (See "To

Transport" in the Operation section of this manual).

4. Sit on seat in operating position, de- press brake pedal and set the parking

brake.

5. Press lift lever plunger and raise attachment lift lever to its highest posi-

tion.

6. Start the engine. After engine has started, move throttle control to idle position.

7. Release parking brake.

8. Slowly move the motion control lever forward and slowly drive tractor off

skid.

9. Apply brake to stop tractor and set parking brake.

10.Turn ignition key to "STOP" position.

Continue with the instructions that follow. CHECK TIRE PRESSURE

The tires on your tractor were overinflated

at the factory for shipping purposes. Cor- rect tire pressure is important for best

cutting performance.

• Reduce tire pressure to PSI shown in "PRODUCT SPECIFICATIONS" section

of this manual.

CHECK DECK LEVELNESS For best cutting results, mower hous-

ing should be properly leveled. See "TO LEVEL MOWER HOUSING" in the Service

and Adjustments section of this manual.

CHECK FOR PROPER POSITION OF ALL BELTS

See the figures that are shown for replac- ing motion and mower blade drive belts in the Service and Adjustments section of this manual. Verify that the belts are routed correctly.

CHECK BRAKE SYSTEM

After you learn how to operate your trac- tor, check to see that the brake is properly adjusted. See "TO ADJUST BRAKE" in the Service and Adjustments section of

this manual.

,/CHECKLIST

Before you operate your new tractor, we wish to assure that you receive the best performance and satisfaction from this Quality Product. Please review the following checklist: ,/All assembly instructions have been

completed.

,/No remaining loose parts in carton. ,/Battery is properly prepared and

charged. (Minimum 1 hour at 6 amps).

,/Seat is adjusted comfortably and tight-

ened securely.

,/All tires are properly inflated. (For ship-

ping purposes, the tires were overin-

flated at the factory).

,/Be sure mower deck is properly leveled

side-to-side/front-to-rear for best cutting results. (Tires must be properly inflated

for leveling).

,/Check mower and drive belts. Be sure

they are routed properly around pulleys

and inside all belt keepers.

,/Check wiring. See that all connections

are still secure and wires are properly

clamped.

,/Before driving tractor, be sure freewheel

control is in "transmission engaged"

position (see "TO TRANSPORT" in the

Operation section of this manual). While learning how to use your tractor, pay extra attention to the following important

items:

,/Engine oil is at proper level. ,/Fuel tank is filled with fresh, clean, regu-

lar unleaded gasoline. ,/Become familiar with all controls, their

location and function. Operate them

before you start the engine. ,/Be sure brake system is in safe operat-

ing condition. ,/Be sure Operator Presence System

and Reverse Operation System (ROS)

are working properly (See the Opera-

tion and Maintenance sections in this

manual). ,/It is important to purge the transmission

before operating your tractor for the first

time. Follow proper starting and trans-

mission purging instructions (See "TO

START ENGINE" and "PURGE TRANS-

MISSION" in the Operation section of

this manual).

Thesesymbolsmayappearon yourtractoror inliteraturesuppliedwiththe product.

Learnand understandtheirmeaning.

R N H L I',,I

REVERSE NEUTRAL HIGH LOW CHOKE FAST

SLOW

IGNITION SWITCF

G G

ENGINE OFF REVERSE ENGINE ON ENGINE START PARKING BRAKE

OPERATION

SYSTEM (ROS)

PARKING BRAKE PARKING BRAN

LOCKED UNLOCKED

OVER TEMP

LIGHT

FUEL OIL PRESSURE BATTERY REVERSE

FORWARD MOWER HEIGHT MOWER LIFT

ATTACHMENT ATTACHMENT

CLUTCH DISENGAGED CLUTCH ENGAGED

LIGHTS ON

FREE WHEEL

(Automatic Models only)

DANGER, KEEP HANDS

AND FEET AWAY

Failure to follow instructions could result in serious injury or

death. The safety alert symbol is used to identify safety inform-

ation about hazards which can result in death, serious injury

and/or property damage.

BRAK_CLUTCH

PEDAL

will result in death or serious injury.

KEEP AREA CLEAR SLOPE HAZARDS

(SEE SAFETY RULES SECTION)

DANGER indicates a hazard which, if not avoided,

WARNING indicates a hazard which, if not avoided,

could result in death or serious injury.

CAUTION indicatesa hazard which, if not avoided,

might result in minor or moderate injury.

CAUTION when used without the alert symbol, indicates a situation that could result in damage

to the tractor and/or engine.

HOT SURFACES indicatesa hazard which, if not avoided, could result in death, serious injur

and/or property damage.

FIRE indicates a hazard which, if not avoided, could result in death, serious injury and/or

property damage.

KNOW YOUR TRACTOR READ THIS OWNER'S MANUAL AND SAFETY RULES BEFORE OPERATING YOUR

TRACTOR

Compare the illustrations with your tractor to familiarize yourself with the locations of

various controls and adjustments. Save this manual for future reference.

Choke Control Ignition "ON"

Ammeter Switch Position

Attachment Clutch

Motion Drive Belt Tension

Handle

Free Wheel Control

Brake Pedal

Height

Adjustment

Knob

Light Switch

Lift Lever

Plunger

Attachment Lift Lever

g Brake

Lever

Control

Lever

Our tractors conform to the safety standards of the

American National Standards Institute.

AMMETER - Indicates charging (+) or

discharging (-) of battery.

ATTACHMENT CLUTCH SWITCH - Used to engage the mower blades, or other at-

tachments mounted to your tractor. ATTACHMENT LIFT LEVER - Used to raise

and lower the mower deck or other attachments

mounted to your tractor. BRAKE PEDAL - Used for braking the

tractor and starting the engine.

CHOKE CONTROL - Used when starting a cold engine.

FREEWHEEL CONTROL - Disengages transmission for pushing or slowly towing the tractor with the engine off.

HEIGHT ADJUSTMENT KNOB - Used to

adjust the mower cutting height.

IGNITION SWITCH - Used for starting and

stopping the engine.

LIFT LEVER PLUNGER - Used to release attachment lift lever when changing its

position. LIGHT SWITCH - Turns the headlights on

and off. MOTION CONTROL LEVER - Selects the speed and direction of tractor.

MOTION DRIVE BELT TENSION HAN- DLE - Used when changing motion drive

belt and, if necessary, starting engine under extremely cold conditions.

PARKING BRAKE LEVER - Locks brake pedal into the brake position.

REVERSE OPERATION SYSTEM (ROS) "ON" POSlTON - Allows operation of mower deck or

other powered attachment while in reverse. THROTTLE CONTROL - Used to control

engine speed.

SAFETYGLASSES

The operation of any tractor can result in foreign objects thrown into the eyes, which can result in severe eye damage. Always wear safety

glasses or eye shields while operating your tractor or performing any adjustments or repairs. We recommend standard safety glasses or a

wide vision safety mask worn over spectacles.

HOW TO USE YOUR TRACTOR

TO SET PARKING BRAKE

Your tractor is equipped with an operator

presence sensing switch. When engine is running, any attempt by the operator

to leave the seat without first setting the

parking brake will shut off the engine.

1. Depress brake pedal all the way down and hold.

2. Pull parking brake lever up and release pressure from brake pedal. Pedal should remain in brake position. Make sure parking brake will hold tractor

secure.

Choke Push-In to Attachment Clutch Control ngage" Switch Pull Out to

Throttle Control

Pedal

Adjustment Parking Brake Knob "Disengaged" "Engaged"

Brake Pedal Position Position

"Drive" Position

STOPPING MOWER BLADES -

• To stop mower blades, push attachment

clutch switch in to disengaged position.

GROUND DRIVE -

• To stop ground drive, depress brake

pedal all the way down.

IMPORTANT: The motion control lever returns to neutral (N) position when the

brake pedal is fully depressed. ENGINE -

• Move throttle control between half and

full speed (fast) position.

NOTE: Failure to move throttle control between half and full speed (fast) posi-

tion, before stopping, may cause engine to

"backfire".

• Turn ignition key to "STOP" position and

remove key. Always remove key when leaving tractor to prevent unauthorized

use.

"Engage"

Motion Control

_ever

• Never use choke to stop engine. IMPORTANT: Leaving the ignition switch in any position other than "STOP" will

cause the battery to discharge and go dead.

NOTE: Under certain conditions when

tractor is standing idle with the engine

running, hot engine exhaust gases may

cause "browning" of grass. To eliminate this possibility, always stop engine when stopping tractor on grass areas.

_CAUTION: Always stop tractor com-

pletely, as described above, before leaving

the operator's position. TO USE THROTTLE CONTROL

Always operate engine at full throttle.

• Operating engine at less than full

throttle reduces the battery charging

rate.

• Full throttle offers the best mower per-

formance.

TO USE CHOKE CONTROL

Use choke control whenever you are start- ing a cold engine. Do not use to start a

warm engine.

• To engage choke control, pull knob out.

Slowly push knob in to disengage.

TO MOVE FORWARD AND

BACKWARD

CAUTION: Do not attempt to operate mo-

tion control lever when the parking brake

is set or when the brake pedal is de- pressed. Doing so may result in misadjust- ment to the drive control system.

The direction and speed of movement is controlled by the motion control lever.

1. Start tractor with motion control lever in

neutral (N) position.

2. Release parking brake.

3. Slowly move motion control lever to

desired position.

TO ADJUST MOWER CUTTING HEIGHT The cutting height is controlled by turn-

ing the height adjustment knob in desired

direction.

• Turn knob clockwise (_) to raise cut-

ting height.

• Turn knob counterclockwise (p_) to

lower cutting height.

Thecuttingheight rangeisapproximately

1-1/2"to4-1/2". Theheightsaremea-

suredfromthe groundtothe bladetip with theengine notrunning. These heightsare approximateand may varydependinguponsoilconditions,

heightof grassandtypesof grassbeing

mowed.

• The averagelawnshouldbecut to

approximately2-1/2 inchesduringthe coolseasonand to over3 inchesduring

hotmonths. Forhealthierandbetter lookinglawns,mowoftenandafter

moderategrowth.

• Forbestcutting performance,grassover

6 inchesin heightshouldbe mowed twice. Makethefirstcut relativelyhigh; thesecondto desiredheight.

TO ADJUST GAUGE WHEELS

Gauge wheels are properly adjusted when they are slightly off the ground when

mower is at the desired cutting height in

operating position. Gauge wheels then

keep the deck in proper position to help

prevent scalping in most terrain conditions.

NOTE: Be sure tractor is on a flat level

surface.

1. Lower mower and adjust mower to desired cutting height.

2. Remove retainer spring and clevis pin which secure each gauge wheel bar.

3. Lower gauge wheels to ground. Raise gauge wheels slightly to align holes

in bracket and gauge wheel bar and insert clevis pin. Gauge wheels should be slightly off the ground.

4. Replace retainer spring into clevis pin.

5. Be sure all gauge wheels are in the same setting.

IMPORTANT: Be sure to readjust gauge

wheels if you change the cutting height

of the mower deck.

Retainer Spring

C_vis

TO OPERATE MOWER Your tractor is equipped with an operator

presence sensing switch. Any attempt by the operator to leave the seat with the engine running and the attachment clutch engaged will shut off the engine. You must remain fully and centrally positioned in the seat to prevent the engine from hesitating or cutting off when operating your equip- ment on rough, rolling terrain or hills.

1. Select desired height of cut.

2. Lower mower with attachment lift con- trol.

3. Start mower blades by engaging at- tachment clutch control.

TO STOP MOWER BLADES - disengage attachment clutch control.

CAUTION: Do not operate the mower

without either the entire grass catcher, on mowers so equipped, or the deflector shield in place.

Attachment Clutch Switch Pull Out to Attachemnt Lift

"Engage" Lever High Position

Deflector Shield

Push:In to "Disengage"

REVERSE OPERATION SYSTEM (ROS) Your tractor is equipped with a Reverse

Operation System (ROS). Any attempt by the operator to travel in the reverse direc- tion with the attachment clutch engaged will shut off the engine unless ignition key is placed in the ROS "ON" position.

,4_WARNING: Backing up with the at- tachment clutch engaged while mowing is strongly discouraged. Turning the ROS

"ON", to allow reverse operation with the attachment clutch engaged, should only be done when the operator decides it is necessary to reposition the machine with the attachment engaged. Do not mow in reverse unless absolutely necessary.

USING THE REVERSE OPERATION SYSTEM -

1. Move motion control lever to neutral (N) position.

2. With engine running, turn ignition key counterclockwise to ROS "ON" posi- tion.

3. Look down and behind before backing.

4. Slowly move motion control lever to reverse (R) position to start movement.

5. When use of the ROS is no longer needed, turn the ignition key clockwise to engine "ON" position.

ROS "ON" Position Engine "ON" Position

(Normal Operating)

TO OPERATE ON HILLS AI_,WARNING: Do not drive up or down

hills with slopes greater than 15° and do not drive across any slope. Use the slope

guide provided at the back of this manual.

• Choose the slowest speed before start-

ing up or down hills.

• Avoid stopping or changing speed on

hills.

• If stopping is absolutely necessary, push

brake pedal quickly to brake position and engage parking brake.

IMPORTANT: The motion control lever returns to neutral (N) position when the

brake pedal is depressed.

• To restart movement, slowly release

parking brake and brake pedal.

• Slowly move motion control lever to

slowest setting.

• Make all turns slowly.

TO TRANSPORT When pushing or towing your tractor, be

sure to disengage transmission by placing

freewheel control in freewheeling position.

Freewheel control is located at the rear drawbar of tractor.

1. Raise attachment lift to highest position with attachment lift control.

2. Pull freewheel control out and into the slot and release so it is held in the

disengaged position.

• Do not push or tow tractor at more than

two (2) MPH.

• To re-engage transmission, reverse

above procedure.

Transmission Engaged

Transmission Disengaged

NOTE: To protect hood from damage when transporting your tractor on a truck or a trailer, be sure hood is closed and secured to tractor. Use an appropriate

means of tying hood to tractor (rope, cord, etc.).

TOWING CARTS AND OTHER ATTACH-

MENTS Tow only the attachments that are recom-

mended by and comply with specifications of the manufacturer of your tractor. Use

common sense when towing. Too heavy of a load, while on a slope, is dangerous.

Tires can lose traction with the ground and cause you to lose control of your tractor.

BEFORE STARTING THE ENGINE CHECK ENGINE OIL LEVEL

The engine in your tractor has been shipped, from the factory, already filled

with summer weight oil.

1. Check engine oil with tractor on level ground.

2. Unthread and remove oil fill cap/ dipstick; wipe oil off. Reinsert the

dipstick into the tube and rest oil fill cap on the tube. Do not thread the cap

onto the tube. Remove and read oil

level. If necessary, add oil until "FULl" mark on dipstick is reached. Do not

overfill.

• For cold weather operation you should

change oil for easier starting (See the

oil viscosity chart in the Maintenance section of this manual).

• To change engine oil, see the Mainte-

nance section in this manual.

ADD GASOLINE

• Fill fuel tank to bottom of filler neck. Do

not overfill. Use fresh, clean, regular unleaded gasoline with a minimum of

87 octane. (Use of leaded gasoline will

increase carbon and lead oxide deposits

and reduce valve life). Do not mix oil with gasoline. Purchase fuel in quan- tities that can be used within 30 days to

assure fuel freshness.

_,CAUTION: Wipeoff anyspilled oilor fuel. Do not store,spill oruse gasoline

nearanopen flame. IMPORTANT:Whenoperatingin temper-

aturesbelow32°F(0°C),use fresh,clean wintergradegasolineto helpinsuregood coldweatherstarting.

CAUTION: Alcoholblendedfuels (called

gasoholorusingethanolormethanol)can

attractmoisturewhichleads to separa- tion andformationof acidsduringstorage. Acidicgascan damagethefuel system

ofan enginewhile in storage.Toavoid engineproblems,the fuelsystemshould

beemptiedbeforestorageof 30 days

orlonger. Drainthe gas tank,start the engineand letit rununtilthefuel lines

andcarburetorareempty. Usefresh fuel

nextseason. SeeStorageInstructionsfor

additionalinformation. Neveruseengine

orcarburetorcleaner productsin thefuel tankor permanentdamagemayoccur.

TO START ENGINE

When starting the engine for the first time

or if the engine has run out of fuel, it will take extra cranking time to move fuel from

the tank to the engine.

1. Be sure freewheel control is in the transmission engaged position.

2. Sit on seat in operating position, depress brake pedal and set parking

brake.

3. Move attachment clutch to disengaged position.

4. Move throttle control to fast position

5. Pull choke control out for a cold engine start attempt. For a warm engine start attempt the choke control may not be

needed.

NOTE: Before starting, read the warm and

cold starting procedures below.

6. Insert key into ignition and turn key clockwise to start position and release

key as soon as engine starts. Do

not run starter continuously for more than fifteen seconds per minute. If the engine does not start after several

attempts, push choke control in, wait

a few minutes and try again. If engine

still does not start, pull the choke con- trol out and retry.

WARM WEATHER STARTING (50 ° F and

above)

7. When engine starts, slowly push choke control in until the engine begins to

run smoothly. If the engine starts to run roughly, pull the choke control out slightly for a few seconds and then

continue to push the control in slowly.

The attachments and ground drive can

now be used. If the engine does not accept the load, restart the engine and

allow it to warm up for one minute using

the choke as described above.

COLD WEATHER STARTING (50 ° F and below)

7. When engine starts, slowly push choke control in until the engine begins to run smoothly. Continue to push the choke control in small steps allowing the en- gine to accept small changes in speed and load, until the choke control is fully

in. If the engine starts to run roughly,

pull the choke control out slightly for a few seconds and then continue to push the control in slowly. This may require an engine warm-up period from several seconds to several minutes, depending on the temperature.

NOTE: In extreme cold conditions, if engine will not start you may need to dis- engage the motion drive belt as follows:

1. Be sure parking brake is engaged.

2. Remove retainer spring from the drive belt tension handle to relieve belt ten-

sion.

3. Start engine and allow it to warm up for

three (3) minutes.

4. Shut-off engine and engage parking brake.

5. Engage drive belt tension handle and replace the retainer spring.

AUTOMATIC TRANSMISSION WARM UP Before driving the unit in cold weather,

the transmission should be warmed up as follows:

1. Be sure the tractor is on level ground.

2. Place the motion control lever in neutral. Release the parking brake and

let the brake slowly return to operating position.

3. Allow one minute for transmission to

warm up. This can be done during the engine warm up period.

• The attachments can be used during

the engine warm-up period after the transmission has been warmed up and

may require the choke control be pulled

out slightly. NOTE: If at a high altitude (above 3000 feet) or in cold temperatures (below 32 F)

the carburetor fuel mixture may need to be adjusted for best engine performance

(see "TO ADJUST CARBURETOR" in the Service and Adjustments section of this

manual).

PURGE TRANSMISSION

,_CAUTION: Never engage or dis- engage freewheel lever while the engine

is running.

To ensure proper operation and per- formance, it is recommended that the

transmission be purged before operating tractor for the first time. This procedure will

remove any trapped air inside the trans- mission which may have developed during shipping of your tractor. IMPORTANT: Should your transmission require removal for service or replace- ment, it should be purged after reinstall- ation before operating the tractor.

1. Place tractor safely on level surface with engine off and parking brake set.

2. Disengage transmission by plac- ing freewheel control in disengaged position (See "TO TRANSPORT" in this section of manual).

3. Sitting in the tractor seat, start engine. After the engine is running, move

throttle control to slow position. Disen- gage parking brake.

4. Move motion control lever to full forward position and hold for five (5)

seconds. Move lever to full reverse position and hold for five (5) seconds. Repeat this procedure three (3) times.

NOTE: During this step there will be no movement of drive wheels. The air is being removed from hydraulic drive system.

5. Move motion control lever to neutral (N) position. Shutoff engine and set

parking brake.

6. Engage transmission by placing free- wheel control in engaged position (See

"TO TRANSPORT" in this section of manual).

7. Sitting in the tractor seat, start engine. After the engine is running, move throttle control to half (1/2) speed. Disengage parking brake.

8. Slowly move motion control lever for- ward, after the tractor moves approxi- mately five (5) feet, slowly move motion control lever to reverse position. After the tractor moves approximately five (5) feet return the motion control lever to the neutral (N) position. Repeat this procedure with the motion control lever three (3) times.

Your transmission is now purged and now

ready for normal operation.

MOWING TIPS

• Tire chains cannot be used when the mower housing is attached to tractor.

• Mower should be properly leveled for best mowing performance. See "TO

LEVEL MOWER HOUSING" in the Service and Adjustments section of this

manual.

• The left hand side of mower should be used for trimming.

• Drive so that clippings are discharged onto the area that has already been

cut. Have the cut area to the right of the tractor. This will result in a more

even distribution of clippings and more

uniform cutting.

• When mowing large areas, start by

turning to the right so that clippings will

discharge away from shrubs, fences, driveways, etc. After one or two rounds, mow in the opposite direction making

left hand turns until finished.

(

• If grass is extremely tall, it should be mowed twice to reduce load and pos-

sible fire hazard from dried clippings. Make first cut relatively high; the second

to the desired height.

• Do not mow grass when it is wet.

Wet grass will plug mower and leave

undesirable clumps. Allow grass to dry before mowing.

• Always operate engine at full throttle

when mowing to assure better mow-

ing performance and proper discharge of material. Regulate ground speed by selecting a low enough gear to give the mower cutting performance as well as

the quality of cut desired.

• When operating attachments, select a ground speed that will suit the terrain and give best performance of the at-

tachment being used.

MA,.TE.A.OESO.EOULE

AS YOU COMPLETE

RE OL RSERV,CE VICED ATES

Chh__ Biraek; iOsPe_;i ° n _

Check Operator Presence and

T ROS Systems If

R Check for Loose Fasteners tf I_s I_

A Sharpen/Replace Mower Blades 1_3 TC Lubrication Chart If If

0 Check Battery Level 1_4 R Clean Battery and Terminals If

Check Transaxle Cooling Check V-Belts If

Check Engine Oil Level I_ If Change Engine Oil (with oil filter) 1_1,2 I_

i= Change Engine Oil (without oil filter) I_1,_ I_

N Clean Air Filter _llf 2

G Clean Air Screen _111_2

Inspect Muffler/Spark Arrester I_

E Replace Oil Filter (If equipped) _1_,2

Clean Engine Cooling Fins If 2 Replace Spark Plug If I_

Replace Air Filter Paper Cartridge V'2

Replace Fuel Filter

1 - Change more often when operating under a heavy load or

in high ambient temperatures.

2 - Service more often when operating in dirty or dusty conditions.

GENERAL RECOMMENDATIONS

The warranty on this tractor does not cover items that have been subjected to

operator abuse or negligence. To receive

full value from the warranty, operator

must maintain tractor as instructed in this manual.

Some adjustments will need to be made periodically to properly maintain your

tractor. At least once a season, check to see if you should make any of the adjustments

described in the Service and Adjustments section of this manual.

• At least once a year you should replace the spark plug, clean or replace air filter,

and check blades and belts for wear. A new spark plug and clean air filter

assure proper air-fuel mixture and help

your engine run better and last longer.

BEFORE EACH USE

1. Check engine oil level.

2. Check brake operation.

3. Check tire pressure.

4. Check operator presence and

ROS systems for proper operation.

5. Check for loose fasteners.

3 - Replace blades more often when mowing in sandy soil. 4 - Not required if equipped with maintenance-free battery. 5 - Tighten front axle pivot bolt to 35 ft.-Ibs, maximum.

Do not overtighten.

LUBRICATION CHART

S_ Spindle

Zerk Zerk

Front Wheel

Bearing zerk

Sector Gear Teeth

(l_bGeneral Purpose Grease (2bRefer to Maintenance "ENGINE" Section

IMPORTANT: Do not oil or grease the pivot points which have special nylon bearings. Viscous lubricants will attract

dust and dirt that will shorten the life of the self-lubricating bearings. If you feel

they must be lubricated, use only a dry, powdered graphite type lubricant sparingly.

Front Wheel

Bearing zerk

Engine

Mandrel

Zerks

TRACTOR Always observe safety rules when per-

forming any maintenance.

BRAKE OPERATION If tractor requires more than five (5) feet to

stop at highest speed in highest gear on a level, dry concrete or paved surface, then brake must be checked and adjusted. (See

"TO ADJUST BRAKE" in the Service and

Adjustments section of this manual). TIRES

• Maintain proper air pressure in all tires (See "PRODUCT SPECIFICATIONS" section of this manual).

• Keep tires free of gasoline, oil, or insect control chemicals which can harm rub-

ber.

• Avoid stumps, stones, deep ruts, sharp objects and other hazards that may

cause tire damage.

NOTE: To seal tire punctures and prevent

flat tires due to slow leaks, tire sealant

may be purchased from your local parts dealer. Tire sealant also prevents tire dry

rot and corrosion. OPERATOR PRESENCE SYSTEM AND

REVERSE OPERATION SYSTEM (ROS) Be sure operator presence and reverse

operation systems are working properly. If

your tractor does not function as de-

scribed, repair the problem immediately.

• The engine should not start unless the brake pedal is fully depressed, and the

attachment clutch control is in the disen- gaged position.

CHECK OPERATOR PRESENCE SYSTEM

• When the engine is running, any at- tempt by the operator to leave the seat without first setting the parking brake should shut off the engine.

• When the engine is running and the attachment clutch is engaged, any at- tempt by the operator to leave the seat should shut off the engine.

• The attachment clutch should never op- erate unless the operator is in the seat.

ROS "ON" Position Engine "ON" Position

(Normal Operating)

CHECK REVERSE OPERATION (ROS) SYSTEM

• When the engine is running with the ignition switch in the engine "ON" posi-

tion and the attachment clutch engaged,

any attempt by the operator to shift into reverse should shut off the engine.

• When the engine is running with the ignition switch in the ROS "ON" position and the attachment clutch engaged, any attempt by the operator to shift into reverse should NOT shut off the engine.

BLADE CARE For best results mower blades must be

kept sharp. Replace bent or damaged blades.

_, CAUTION: Use only a replacement

blade approved by the manufacturer of

your tractor. Using a blade not approved

by the manufacturer of your tractor is hazardous, could damage your tractor and

void your warranty.

BLADE REMOVAL

1. Raise mower to highest position to al- low access to blades.

NOTE: Protect your hands with gloves

and/or wrap blade with heavy cloth.

2. Remove blade bolt by turning counter- clockwise.

3. Install new or resharpened blade with stamped "THIS SIDE UP" facing deck

and mandrel assembly.

IMPORTANT: To ensure proper assembly, center hole in blade must align with star on mandrel assembly.

4. Install and tighten blade bolt securely

(45-55 Ft. Lbs. torque).

IMPORTANT: Special blade bolt is heat treated.

___ _ Mandrel

Blade Bolt/J_ _ _'_'_"Star

(Special)" Cen{er Hole"_

TO SHARPEN BLADE

NOTE: We do not recommend sharp- ening blade - but if you do, be sure the

blade is balanced. Care should be taken to keep the blade

balanced. An unbalanced blade will cause excessive vibration and eventual damage

to mower and engine.

• The blade can be sharpened with a file

or on a grinding wheel. Do not attempt

to sharpen while on the mower.

)) Assembly

• To check blade balance, you will need a 5/8" diameter steel bolt, pin, or a cone

balancer. (When using a cone balancer, follow the instructions supplied with balancer.)

NOTE: Do not use a nail for balancing blade. The lobes of the center hole may

appear to be centered, but are not.

• Slide blade on to an unthreaded portion of the steel bolt or pin and hold the

bolt or pin parallel with the ground. If blade is balanced, it should remain in a

horizontal position. If either end of the blade moves downward, sharpen the heavy end until the blade is balanced.

5/8" Bolt or Pin

Do not attempt to clean fan or transmis- sion while engine is running or while the transmission is hot. To prevent possible damage to seals, do not use high pressure

water or steam to clean transaxle.

• Inspect cooling fan to be sure fan blades are intact and clean.

• Inspect cooling fins for dirt, grass clip- pings and other materials. To prevent damage to seals, do not use com- pressed air or high pressure sprayer to

clean cooling fins.

TRANSAXLE PUMP FLUID

The transaxle was sealed at the factory and fluid maintenance is not required for

the life of the transaxle. Should the trans- axle ever leak or require servicing, contact

a Sears or other qualified service center.

Center Hole

BATTERY

Your tractor has a battery charging system which is sufficient for normal use. How-

ever, periodic charging of the battery with

an automotive charger will extend its life.

• Keep battery and terminals clean.

• Keep battery bolts tight.

• Keep small vent holes open.

• Recharge at 6-10 amperes for 1 hour. NOTE: The original equipment battery on

your tractor is maintenance free. Do not

attempt to open or remove caps or covers.

Adding or checking level of electrolyte is

not necessary.

TO CLEAN BATTERY AND TERMINALS

Corrosion and dirt on the battery and

terminals can cause the battery to "leak"

power.

1. Remove terminal guard.

2. Disconnect BLACK battery cable first

then RED battery cable and remove

battery from tractor.

3. Rinse the battery with plain water and

dry.

4. Clean terminals and battery cable ends

with wire brush until bright.

5. Coat terminals with grease or petro-

leum jelly.

6. Reinstall battery (See "REPLACING

BATTERY" in the SERVICE AND AD-

JUSTMENTS section of this manual).

TRANSAXLE COOLING

The transmission fan and cooling fins

should be kept clean to assure proper

cooling.

V-BELTS

Check V-belts for deterioration and wear after 100 hours of operation and replace

if necessary. The belts are not adjustable. Replace belts if they begin to slip from

wear.

ENGINE LUBRICATION Only use high quality detergent oil rated

with API service classification SG-SL. Select the oil's SAE viscosity grade

according to your expected operating temperature.

SAE VISCOSITY GRADES

TEMPERATURE RANGE ANTICIPATED BEFORE NEXT OIL CHANGE

oilviscchart4 e

Change the oil after every 50 hours of op- eration or at least once a year if the tractor is not used for 50 hours in one year.

Check the crankcase oil level before start- ing the engine and after each eight (8)

hours of operation. TO CHANGE ENGINE OIL

Determine temperature range expected before oil change. All oil must meet API

service classification SG-SL.

• Be sure tractor is on level surface.

• Oil will drain more freely when warm.

• Catch oil in a suitable container.

1. Remove oil fill cap/dipstick. Be careful not to allow dirt to enter the engine

when changing oil.

2. Install the drain tube onto the fitting.

3. Open drain valve by using a 7/16" (11 mm) wrench turning counterclock-

wise.

Oil Drain Valve

To Open

To Close

Drain Tube

4. After oil has drained completely, close the drain valve turning clockwise. Use

the 7/16" (11 mm) wrench to apply a small amount of torque to keep it

closed. Do not over tighten.

5. Remove the drain tube and store in a safe place.

6. Refill engine with oil through oil fill dip- stick tube. Pour slowly. Do not overfill. For approximate capacity see "PROD-

UCT SPECIFICATIONS" section of this manual.

7. Use gauge on oil fill cap/dipstick for checking level. Insert dipstick into the tube and rest the oil fill cap on the tube. Do not thread the cap onto the tube when taking reading. Keep oil at "FULl" line on dipstick. Tighten cap onto the tube securely when finished.

ENGINE OIL FILTER Replace the engine oil filter every season

or every other oil change if the tractor is used more than 100 hours in one year.

AIR FILTER

Your engine will not run properly using a

dirty air filter. Clean the foam pre-cleaner after every 25 hours of operation or every season. Service paper cartridge every 100 hours of operation or every season,

whichever occurs first.

Service air cleaner more often under dusty

conditions.

1. Loosen knob and remove cover.

TO SERVICE PRE-CLEANER

2. Slide foam pre-cleaner off cartridge.

3. Wash it in liquid detergent and water.

4. Squeeze it dry in a clean cloth. Allow it to dry.

5. Saturate it in engine oil. Wrap it in clean, absorbent cloth and squeeze to

remove excess oil.

TO SERVICE CARTRIDGE

• Replace a dirty, bent, or damaged car-

tridge.

NOTE: Do not wash the paper cartridge or use pressurized air, as this will damage the cartridge.

1. Remove nut and cartridge plate.

2. Reinstall the pre-cleaner (cleaned and

oiled) over the paper cartridge.

3. Check rubber seal for damage and

proper position around stud. Replace if necessary.

4. Reassemble air cleaner, cartridge

plate, and nut.

5. Reinstall air cleaner cover and secure

by tightening knob.

Cartridge

Foam Pre-Cleaner

Nut

Rubber

Seal

--.Cartridge Plate

CLEAN AIR SCREEN

Air screen must be kept free of dirt and chaff to prevent engine damage from overheating. Clean with a wire brush or

compressed air to remove dirt and stub-

born dried gum fibers.

CLEAN AIR INTAKE/COOLING AREAS

To insure proper cooling, make sure the grass screen, cooling fins, and other exter-

nal surfaces of the engine are kept clean

at all times.

Every 100 hours of operation (more often under extremely dusty, dirty conditions),

remove the blower housing and other cool- ing shrouds. Clean the cooling fins and

external surfaces as necessary. Make sure the cooling shrouds are reinstalled.

NOTE: Operating the engine with a blocked grass screen, dirty or plugged

cooling fins, and/or cooling shrouds

removed will cause engine damage due to

overheating.

MUFFLER Inspect and replace corroded muffler and

spark arrester (if equipped) as it could cre- ate a fire hazard and/or damage.

SPARK PLUG(S) Replace spark plug(s) at the beginning

of each mowing season or after every 100 hours of operation, whichever occurs

first. Spark plug type and gap setting are

shown in "PRODUCT SPECIFICATIONS" section of this manual.

IN-LINE FUEL FILTER

The fuel filter should be replaced once each season. If fuel filter becomes

clogged, obstructing fuel flow to carbu-

retor, replacement is required.

1. With engine cool, remove filter and plug fuel line sections.

2. Place new fuel filter in position in fuel line with arrow pointing towards carbu-

retor.

3. Be sure there are no fuel line leaks and clamps are properly positioned.

4. Immediately wipe up any spilled gaso- line.

Clamp

Fuel Filter-

CLEANING

• Clean engine, battery, seat, finish, etc. of all foreign matter.

• Keep finished surfaces and wheels free of all gasoline, oil, etc.

• Protect painted surfaces with auto- motive type wax.

We do not recommend using a garden hose or pressure washer to clean your tractor unless the engine and transmis- sion are covered to keep water out. Water in engine or transmission will shorten the useful life of your tractor. Use compressed air or a leaf blower to remove grass,

leaves and trash from tractor and mower.

+ 44 hidden pages