Craftsman 917273470 Owner’s Manual

Owner's Manual

I("nFTSMnN,I

LAWN TRACTOR

20.0 HP, 42" Mower Electric Start

6 Speed Transaxle

Model No.

917.273470

This product has a low emission engine which operates 1

III III differently from previously built engines. Before you start the I

engine, read and understand this Owner's Manual.

IMPORTANT: Read and follow all Safety

Rules and Instructions before

operating this equipment.

Sears, Roebuck and Co., Hoffman Estates, IL 60179 U.S.A.

Visit our Craftsman website:www.sears.com/craftsman

For answers to your questions

about this product, Call:

1-800-659-5917

Sears Craftsman Help Line 5 am - 5 pm, Mon - Sat

Warranty ................................................. 2

Safety Rules ........................................... 3

Product Specifications ............................ 6

Assembly/P re-Operation ........................ 8

Operation .............................................. 11

Maintenance Schedule ......................... 17

LIMITED WARRANTY ON CRAFTSMAN RIDING EQUIPMENT For two (2) years from the date of purchase, if this Craftsman Riding Equipment is

maintained, lubricated and tuned up according to the instructions in the owner's manual, Sears will repair or replace free of charge any parts that are found to be defective in

material or workmanship according to the guidelines of coverage listed below. Sears will

also provide free labor for these applicable warranted parts for the two full years. During the first 30 days of purchase, there will be no charges to service the product at your

home for issues covered by this warranty. (See exclusions below). For your conve- nience, IN HOME warranty service will still be available after the first 30 days of pur-

chase, but a trip charge will apply. This charge will be waived if the Craftsman product is dropped off at an authorized Sears location. For the nearest authorized Sears location,

please call 1-800-4-MY-HOME®. This warranty applies only while this product is within

the United States. This Warranty does not cover:

• Expendable items which become worn during normal use, including but not limited to blades, spark plugs, air cleaners, belts, and oil filters.

• Standard Maintenance Servicing, oil changes, or tune-ups

• Tire replacement or repair caused by punctures from outside objects, such as nails,

thorns, stumps, or glass.

• Repairs necessary because of operator abuse, including but not limited to, damage caused by towing objects beyond the capability of the riding equipment, impacting

objects that bend the frame or crankshaft, or over-speeding the engine.

• Repairs necessary because of operator negligence, including but not limited to, elec-

trical and mechanical damage caused by improper storage, failure to use the proper

grade and amount of engine oil, failure to keep the deck clear of flammable debris, or failure to maintain the equipment according to the instructions contained in the

owner's manual.

• Engine (fuel system) cleaning or repairs caused by fuel determined to be contami- nated or oxidized (stale). In general, fuel should be used within 30 days of its pur-

chase date.

• Normal deterioration and wear of the exterior finishes, or product label replacement.

• Riding equipment used for commercial or rental purposes.

LIMITED WARRANTY ON BATTERY For ninety (90) days from date of purchase, if any battery included with this riding equip-

ment proves defective in material or workmanship and our testing determines the battery

will not hold a charge, Sears will replace the battery at no charge. During the first 30 days of purchase, there will be no charges to replace the battery at your HOME. After the first 30 days, for your convenience, IN-HOME warranty service will still be avail-

able but a trip charge will apply. This charge will be waived if the Craftsman product is dropped off at an authorized Sears location. For the nearest authorized Sears location,

please call 1-800-4-MY-HOME®.

Maintenance ......................................... 17

Service and Adjustments ...................... 21

Storage ................................................. 27

Troubleshooting .................................... 28

Repair Parts .......................................... 32

Sears Service ......................... Back Cover

This battery warranty applies only while this product is within the United States. This warranty gives you specific legal rights, and you may also have other rights, which

vary, from state to state.

Sears, Roebuck and Co.,Dept.817WA, Hoffman Estates, IL 60179

IMPORTANT: This cutting machine is capable of amputating hands and feet and throw- ing objects. Failure to observe the following safety instructions could result in serious injury or death.

A(_WARNING: In order to prevent ac- cidental starting when setting up, trans-

porting, adjusting or making repairs,

always disconnect spark plug wire and

place wire where it cannot contact spark plug.

AlutLWARNING: Do not coast down a hill in

neutral, you may lose control of the tractor. _WARNING: Tow only the attachments that are recommended by and comply with

specifications of the manufacturer of your tractor. Use common sense when towing. Operate only at the lowest possible speed when on a slope. Too heavy of a load, while on a slope, is dangerous. Tires can

lose traction with the ground and cause you to lose control of your tractor.

_WARNING: Engine exhaust, some of

its constituents, and certain vehicle com-

ponents contain or emit chemicals known to the State of California to cause cancer

and birth defects or other reproductive

harm. A(_WARNING: Battery posts, terminals

and related accessories contain lead and

lead compounds, chemicals known to the

State of California to cause cancer and

birth defects or other reproductive harm. Wash hands after handling.

I. GENERAL OPERATION

• Read, understand, and follow all instruc-

tions in the manual and on the machine before starting.

• Only allow responsible adults, who are

familiar with the instructions, to operate the machine.

• Clear the area of objects such as rocks,

toys, wire, etc., which could be picked up and thrown by the blade.

• Be sure the area is clear of other people

before mowing. Stop machine if anyone enters the area.

• Never carry passengers.

• Do not mow in reverse unless abso-

lutely necessary. Always look down and behind before and while backing.

• Be aware of the mower discharge direc- tion and do not point it at anyone. Do

not operate the mower without either

the entire grass catcher or the guard in

place.

• Slow down before turning.

• Never leave a running machine unat- tended. Always turn off blades, set

parking brake, stop engine, and remove keys before dismounting.

• Turn off blades when not mowing.

• Stop engine before removing grass catcher or unclogging chute.

• Mow only in daylight or good artificial

light.

• Do not operate the machine while under the influence of alcohol or drugs.

• Watch for traffic when operating near or crossing roadways.

• Use extra care when loading or un-

loading the machine into a trailer or

truck.

• Data indicates that operators, age 60 years and above, are involved in a large

percentage of riding mower-related in- juries. These operators should evaluate their ability to operate the riding mower safely enough to protect themselves and others from serious injury.

• Keep machine free of grass, leaves or other debris build-up which can touch

hot exhaust / engine parts and burn. Do not allow the mower deck to plow leaves

or other debris which can cause build-

up to occur. Clean any oil or fuel

spillage before operating or storing the

machine. Allow machine to cool before

storage.

II. SLOPE OPERATION

Slopes are a major factor related to loss- of-control and tipover accidents, which can

result in severe injury or death. All slopes require extra caution. If you cannot back

up the slope or if you feel uneasy on it, do not mow it.

DO:

• Mow up and down slopes, not across.

• Remove obstacles such as rocks, tree limbs, etc.

• Watch for holes, ruts, or bumps. Un- even terrain could overturn the machine.

Tall grass can hide obstacles.

• Use slow speed. Choose a low gear so that you will not have to stop or shift while on the slope.

• Follow the manufacturer's recommend- ations for wheel weights or counter-

weights to improve stability.

• Use extra care with grass catchers or other attachments. These can change

the stability of the machine.

• Keep all movement on the slopes slow and gradual Do not make sudden

changes in speed or direction.

• Avoid starting or stopping on a slope. If

tires lose traction, disengage the blades

and proceed slowly straight down the slope.

DO NOT:

• Do not turn on slopes unless neces- sary, and then, turn slowly and gradually downhill, if possible.

• Do not mow near drop-offs, ditches, or embankments. The mower could

suddenly turn over if a wheel is over

the edge of a cliff or ditch, or if an edge

caves in.

• Do not mow on wet grass. Reduced

traction could cause sliding.

• Do not try to stabilize the machine by putting your foot on the ground.

• Do not use grass catcher on steep slopes.

III, CHILDREN

Tragic accidents can occur ifthe operator

is not alert to the presence of children.

Children are often attracted to the ma- chine and the mowing activity. Neveras-

sume that children will remain where you

last saw them.

• Keep children out of the mowing area and under the watchful care of another

responsible adult.

• Be alert and turn machine off if children enter the area.

• Before and when backing, look behind and down for small children.

• Never carry children. They may fall off and be seriously injured or interfere with safe machine operation.

• Never allow children to operate the

machine.

• Use extra care when approaching blind corners, shrubs, trees, or other objects that may obscure vision.

IV. SERVICE

• Use extra care in handling gasoline and other fuels. They are flammable and

vapors are explosive.

- Use only an approved container.

- Never remove gas cap or add fuel with the engine running. Allow

engine to cool before refueling. Do not smoke.

- Never refuel the machine indoors.

- Never store the machine or fuel container inside where there is an

open flame, such as a water heater.

• Never run a machine inside a closed area.

• Keep nuts and bolts, especially blade attachment bolts, tight and keep equip-

ment in good condition.

• Never tamper with safety devices. Check their proper operation regularly.

• Keep machine free of grass, leaves, or other debris build-up. Clean oil or fuel spillage. Allow machine to cool before storing.

• Stop and inspect the equipment if you strike an object. Repair, if necessary,

before restarting.

• Never make adjustments or repairs with the engine running.

• Grass catcher components are subject to wear, damage, and deterioration,

which could expose moving parts or allow objects to be thrown. Frequently

check components and replace with

manufacturer's recommended parts,

when necessary.

• Mower blades are sharp and can cut. Wrap the blade(s) or wear gloves, and

use extra caution when servicing them.

• Check brake operation frequently. Ad- just and service as required.

• Be sure the area is clear of other people before mowing. Stop machine if anyone

enters the area.

• Never carry passengers or children even with the blades off.

• Do not mow in reverse unless abso- lutely necessary. Always look down and

behind before and while backing.

• Never carry children. They may fall off and be seriously injured or interfere with safe machine operation.

• Keep children out of the mowing area and under the watchful care of another

responsible adult.

• Be alert and turn machine off if children enter the area.

• Before and when backing, look behind and down for small children.

• Mow up and down slopes (15° Max), not across.

• Remove obstacles such as rocks, tree limbs, etc.

• Watch for holes, ruts, or bumps. Uneven

terrain could overturn the machine. Tall grass can hide obstacles.

• Use slow speed. Choose a low gear

so that you will not have to stop or shift while on the slope.

• Avoid starting or stopping on a slope. If

tires lose traction, disengage the blades and proceed slowly straight down the slope.

• If machine stops while going uphill,

disengage blades, shift into reverse and

back down slowly.

• Be not turn on slopes unless necessary,

and then, turn slowly and gradually downhill, if possible.

PRODUCT SPECIFICATIONS

Gasoline Capacity 4.0

and Type: Oil Type

API-SF-SJ):

Unleaded and Regular SAE 10W30

sabove 32°F)

AE 5W-30(below 32°F

Oil Capacity:

W/Filter: 4.0 Pints W/O Filter: 3.5 Pints

iSpark Plug: i(Gap: .030")

Ground Speed Forward: (MPH): 1st 1.2

Tire Pressure: Front: 14 PSI

Charging System: 15 Amps @ 3600RPM Battery: Amp/Hr: 35

Blade Bolt Torque: 27-35 Ft. Lbs.

Champion RC12YC

2nd 1.5 3rd 2.4 4th 3.5

5th 4.8 6th 5.3

Reverse: 1.5

Rear: 10 PSI

Min. CCA: 280

Case Size: U1R

CONGRATULATIONS on your purchase of a new tractor. It has been designed, engineered and manufactured to give you the best possible dependability and

performance.

Should you experience any problem you cannot easily remedy, please contact a

Sears or other qualified service center. We have competent, well-trained techni- cians and the proper tools to service or

repair this tractor.

Please read and retain this manual. The

instructions will enable you to assemble and maintain your tractor properly. Always

observe the "SAFETY RULES".

CUSTOMER RESPONSIBILITIES

• Read and observe the safety rules.

• Follow a regular schedule in main- taining, caring for and using your tractor.

• Follow the instructions under "Mainte-

nance" and "Storage" sections of this

owner's manual.

_WARNING: This tractor is equipped

with an internal combustion engine and should not be used on or near any unim- proved forest-covered, brush-covered or grass-covered land unless the engine's

exhaust system is equipped with a spark arrester meeting applicable local or state

laws (if any). If a spark arrester is used, it

should be maintained in effective working order by the operator.

In the state of California the above is re- quired by law (Section 4442 of the Califor-

nia Public Resources Code). Other states may have similar laws. Federal laws apply on federal lands. A spark arrester for the muffler is available through your nearest Sears service center (See REPAIR PARTS section of this manual).

REPAIR PROTECTION AGREEMENTS

Congratulations on making a smart pur- chase. Your new Craftsman@ product is designed and manufactured for years of dependable operation. But like all products, it may require repair from time to time. That's when having a Repair Protection Agreement can save you money and aggravation.

Purchase a Repair Protection Agreement now and protect yourself from unexpected hassle and expense.

Here's what's included in the Agreement:

• Expert service by our 12,000 profe- sional repair specialists.

• Unlimited service and no charge for parts and labor on all covered repairs.

• Product replacement if your covered product can't be fixed.

• Discount of 10% from regular price of service and service-related parts not

covered by the agreement; also, 10% off regular price of preventive mainte-

nance check.

• Fast help by phone - phone support from a Sears technician on products

requiring in-home repair, plus conve- nient repair scheduling.

Once you purchase the Agreement, a simple phone call is all that it takes for you to schedule service. You can call anytime day or night, or schedule a service ap- pointment online. Sears has over 12,000 professional repair specialists, who have access to over 4.5 million quality parts and accessories. That's the kind of professionalism you can count on to help prolong the life of your new purchase for years to come. Purchase your Repair Protection Agreement today! Some limitations and exclusions apply.

For prices and additional information

call 1-800-827-6655. SEARS INSTALLATION SERVICE

For Sears professional installation of home appliances, garage door openers, water heaters, and other major home items, in

the U.S.A. call 1-800-4-MY-HOME®

Steering

Wheellnse_

Steering Whee!

(1) Large Flat Washer

(1) Hex Bolt 1/4-28 x 1-1/4

(1) Locknut 1/4-28

Steering Wheel

Adapter

(1) Locknut 1/2-20

_St_eritg

Seat

(1)Washer

@ 17/32 x 1-3/16 x 12 Gauge

_(1) Knob

Steering

Extension

Shaft

Keys

(2) Keys

For Future Use

Slope Sheet Video Cassette

Your new tractor has been assembled at the factory with the exception of those parts left

unassembled for shipping purposes. To ensure safe and proper operation of your tractor all parts and hardware you assemble must be tightened securely. Use the correct tools as necessary to insure proper tightness. Review the video cassette before you begin.

TOOLS REQUIRED FOR ASSEMBLY

A socket wrench set will make assembly easier. Standard wrench sizes you need

are listed below.

(1) 3/4"wrench (1) Pliers (2) 7/16" wrench (1) Utility knife

(1) Tire pressure gauge

When right or left hand is mentioned in this manual, it means when you are in

the operating position (seated behind the steering wheel).

TO REMOVE TRACTOR FROM

CARTON

UNPACK CARTON

1. Remove all accessible loose parts and

parts boxes from carton.

2. Cut along dotted lines on all four pan- els of carton. Remove end panels and lay side panels flat.

3. Check for any additional loose parts or cartons and remove.

BEFORE REMOVING TRACTOR FROM SKID

ATTACH STEERING WHEEL

ASSEMBLE EXTENSION SHAFT AND

BOOT

1. Slide extension shaft onto lower steer- ing shaft. Align mounting holes in ex-

tension and lower shafts and install 1/4

hex bolt and Iocknut. Tighten securely.

IMPORTANT: Tighten bolt and nut se-

curely to 10-12 ft. Ibs torque.

2. Place tabs of steering boot over tab slots in dash and push down to secure.

INSTALL STEERING WHEEL

3. Position front wheels of the tractor so

they are pointing straight forward.

4. Remove steering wheel adapter from steering wheel and slide adapter onto steering shaft extension.

5. Position steering wheel so cross bars are horizontal (left to right) and slide inside boot and onto adapter.

6. Assemble large flat washer, 1/2 hex nut and tighten securely.

7. Snap steering wheel insert into center of steering wheel.

Steering _ Wheel

Adapter Shaft

8. Remove protective materials from trac- tor hood and grill.

IMPORTANT: Check for and remove any staples in skid that may puncture tires

where tractor is to roll off skid.

HOWTO SET UP YOUR TRACTOR

CHECK BATTERY

1. Lift hood to raised position.

NOTE: If this battery is put into service after month and year indicated on label (label located between terminals) charge battery for minimum of one hour at 6-10 amps. (See "BATTERY" in Maintenance section of this manual for charging instruc-

tions).

_-_ Insert

1/2 Hex Nut

Large Flat Washer

Boot

1/4 Hex Bolt

Fab

Slots

INSTALL SEAT

Adjust seat before tightening adjustment

knob.

1. Remove adjustment knob and flat washer securing seat to cardboard packing and set aside for assembly of

seat to tractor.

2. Pivot seat upward and remove from the cardboard packing. Remove the

cardboard packing and discard.

3. Place seat on seat pan so head of

shoulder bolts are positioned over the large slotted holes in pan.

4. Push down on seat to engage shoulder

bolts in slots and pull seat towards rear of tractor.

5. Pivot seat and pan forward and as-

semble adjustment knob and flat washer loosely. Do not tighten.

6. Lower seat into operating position and

sit in seat.

7. Slide seat until a comfortable position

is reached which allows you to press clutch/brake pedal all the way down.

8. Get off seat without moving its ad- justed position.

9. Raise seat and tighten adjustment knob securely.

Seat

Seat I

Shoulder Bolts

Flat

Adjustment Knob

NOTE: You may now roll or drive your tractor off the skid. Follow the appropriate

instruction below to remove the tractor from the skid.

TO ROLLTRACTOR OFF SKID (See Operation section for location and function of controls)

1. Press lift lever plunger and raise attachment lift lever to its highest po- sition.

2. Release parking brake by depressing clutch/brake pedal.

3. Place gearshift lever in neutral (N) position.

4. Roll tractor forward off skid.

5. Remove banding holding deflector shield up against tractor.

TO DRIVE TRACTOR OFF SKID (See Operation section for location and function of controls)

,_WARNING: Before starting, read, un-

derstand and follow all instructions in the Operation section of this manual. Be sure

tractor is in a well-ventilated area. Be sure the area in front of tractor is clear of other

people and objects.

1. Be sure all the above assembly steps have been completed.

2. Check engine oil level and fill fuel tank with gasoline.

3. Sit on seat in operating position, depress clutch/brake pedal and set the parking brake.

4. Place gear shift lever in neutral (N) position.

5. Press lift lever plunger and raise attachment lift lever to its highest posi-

tion.

6. Start the engine. After engine has started, move throttle control to idle

position.

7. Depress clutch/brake pedal into full "BRAKE" position and hold. Move

gearshift lever to 1st gear.

8. Slowly release clutch/brake pedal and slowly drive tractor off skid.

9. Apply brake to stop tractor, set park- ing brake and place gearshift lever in

neutral position.

10.Turn ignition key to "STOP" position.

Continue with the instructions that follow.

INSTALL MULCHER PLATE

(If previously removed)

1. Raise and hold deflector shield in upright position.

2. Place front of mulcher plate over front of mower deck opening and slide into place, as shown.

3. Hook front latch into hole on front of mower deck.

4. Hook rear latch into hole on back of mower deck.

Shield

Plate

Latch Hooks

A(_CAUTION: Do not remove deflector shield from mower. Raise and hold shield when attaching mulcher plate and allow it to rest on plate while in operation.

TO CONVERTTO BAGGING OR

DISCHARGING

Simply remove mulcher plate and store

in a safe place. Your mower is now ready for discharging or installation of optional grass catcher accessory.

NOTE: It is not necessary to change

blades. The mulcher blades are designed for discharging and bagging also.

CHECKTIRE PRESSURE

The tires on your tractor were overinflated

at the factory for shipping purposes.

Correct tire pressure is important for best

cutting performance.

• Reduce tire pressure to PSI shown in "PRODUCT SPECIFICATIONS" section

of this manual.

CHECK DECK LEVELNESS

For best cutting results, mower hous- ing should be properly leveled. See

"TO LEVEL MOWER HOUSING" in the

Service and Adjustments section of this manual.

CHECK FOR PROPER POSITION OF

ALL BELTS See the figures that are shown for replac-

ing motion and mower blade drive belts in the Service and Adjustments section of

this manual. Verify that the belts are routed correctly.

CHECK BRAKE SYSTEM

After you learn how to operate your tractor, check to see that the brake is properly adjusted. See "TO ADJUST BRAKE" in the

Service and Adjustments section of this manual.

,/CHECKLIS T

Before you operate and enjoy your new tractor, we wish to assure that you receive the best performance and satisfaction from this Quality Product.

Please review the following checklist: ,/All assembly instructions have been

completed. ,/No remaining loose parts in carton. ,/Battery is properly prepared and

charged. (Minimum 1 hour at 6 amps). ,/Seat is adjusted comfortably and tight-

ened securely. ,/All tires are properly inflated. (For ship-

ping purposes, the tires were overin-

flated at the factory). ,/Be sure mower deck is properly leveled

side-to-side/front-to-rear for best cutting

results. (Tires must be properly inflated

for leveling). ,/Check mower and drive belts. Be sure

they are routed properly around pulleys

and inside all belt keepers. ,/Check wiring. See that all connections

are still secure and wires are properly

clamped. While learning how to use your tractor, pay

extra attention to the following important

items:

,/Engine oil is at proper level. ,/Fuel tank is filled with fresh, clean, regu-

lar unleaded gasoline. ,/Become familiar with all controls - their

location and function. Operate them

before you start the engine. ,/Be sure brake system is in safe oper-

ating condition.

These symbols may appear on your tractor or in literature supplied with the product.

Learn and understand their meaning.

R N H L I",I

REVERSE NEUTRAL NIGH LOW CHOKE FAST SLOW

IGNITION

(3_----

ENGINE OFF LIGHTS ON ENGINE ON ENGINE START PARKING BRAKE

PARKING BRAKE PARKING BRI

LOCKED UNLOCKEr

OVER TEMP FUEL OIL PRESSURE BATTERY REVERSE FORWARD

LIGHT

ATTACHMENT ATTACHMENT

CLUTCH ENGAGED CLUTCH DISENGAGED

FREE WHEEL

(Automatic Models only)

DANGER, KEEP HANDS

Failure to follow instructions could result in serious injury or

death. The safety alert symbol is used to identify safety inform-

ation about hazards which can result in death, serious injury J_

and/or property damage.

AND FEET AWAY

& &

DANGER indicates a hazard which, if not avoided, will result in death or serious injury.

WARNING indicates a hazard which, if not avoided, could result in death or serious injury.

CAUTION indicates a hazard which, if not avoided, might result in minor or moderate injury.

CAUTION when used without the alert symbol, indicates a situation that could result in damage to the tractor and/or engine.

HOT SURFACES indicates a hazard which, ifnot avoided, could result in death, serious injury

and/or property damage. FIRE indicates a hazard which, if not avoided,

could result in death, serious injury and/or

property damage.

KEEP AREA CLEAR SLOPE HAZARDS

MOWER HEIGHT MOWER LII

(SEE SAFETY RULES SECTION)

KNOW YOUR TRACTOR READ THIS OWNER'S MANUAL AND SAFETY RULES BEFORE OPERATING YOUR

TRACTOR

Compare the illustrations with your tractor to familiarize yourself with the locations of various controls and adjustments. Save this manual for future reference.

Attachment Ignition Switch ht Switch Clutch Lever Position

/_ _ _

Ammeter_ "" Plunger

Attachment

Lift Lever

Throttld

o Height

Clutch/Brake

Pedal

Adjustment

Indicator

Parking Brake Lever

Our tractors conform to the safety standards of the

American National Standards Institute.

AMMETER - Indicates charging (+) or discharging (-) of battery.

ATTACHMENT CLUTCH LEVER - Used to engage the mower blades, or other at- tachments mounted to your tractor.

ATTACHMENT LIFT LEVER - Used to

raise, lower, and adjust the mower deck or

other attachments mounted to your tractor.

CLUTCH/BRAKE PEDAL - Used for

declutching and braking the tractor and starting the engine.

GEARSHIFT LEVER - Selects the speed

and direction of tractor.

IGNITION SWITCH - Used for starting and stopping the engine.

LIFT LEVER PLUNGER - Used to release attachment lift lever when changing its position.

LIGHT SWITCH POSITION -Turns the headlights on and off.

PARKING BRAKE LEVER - Locks clutch/ brake pedal into the brake position.

THROTTLE CONTROL - Used to control engine speed.

CHOKE CONTROL - Used when starting a cold engine.

The operation of any tractor can result in foreign objects thrown into the eyes, which can result in severe eye damage. Always wear safety glasses or eye shields while operating your tractor or performing any adjustments or repairs. We recommend a wide vision safety mask over spectacles or standard safety glasses.

HOW TO USE YOUR TRACTOR

TO SET PARKING BRAKE

Your tractor is equipped with an operator

presence sensing switch. When engine is running, any attempt by the operator

to leave the seat without first setting the

parking brake will shut off the engine.

1. Depress clutch/brake pedal all the way down and hold.

2. Pull parking brake lever up and release pressure from clutch/brake pedal. Pedal should remain in brake position. Make sure parking brake will hold trac-

tor secure.

Attachment Clutch Lever

Choke

Thr{ Position

Clutch/ Position

Brake

"Disengaged" "Brake"

Position Position

STOPPING

MOWER BLADES -

• To stop mower blades, move attachment

clutch lever to disengaged position.

GROUND DRIVE -

• To stop ground drive, depress clutch/

brake pedal all the way down.

• Move gearshift lever to neutral (N)

position.

ENGINE -

• Move throttle control between half and

full speed (fast) position.

NOTE: Failure to move throttle control between half and full speed (fast) posi-

tion, before stopping, may cause engine to "backfire".

• Turn ignition key to "STOP" position and

remove key. Always remove key when leaving tractor to prevent unauthorized

use.

• Never use choke to stop engine.

"En Position

inition Key

,"Disengaged"

Brake

"Engaged"

Gearshift Lever

IMPORTANT: Leaving the ignition switch in any position other than "STOP" will

cause the battery to discharge and go dead.

NOTE: Under certain conditions when tractor is standing idle with the engine

running, hot engine exhaust gases may

cause "browning" of grass. To eliminate this possibility, always stop engine when

stopping tractor on grass areas.

_,CAUTION.- Always stop tractor com-

pletely, as described above, before leaving the operator's position.

TO USE THROTTLE CONTROL

Always operate engine at full throttle.

• Operating engine at less than full throttle reduces the battery charging

rate.

• Full throttle offers the best bagging and

mower performance.

TO USE CHOKE CONTROL

Use choke control whenever you are start- ing a cold engine. Do not use to start a warm engine.

• To engage choke control, pull knob out.

Slowly push knob in to disengage.

TO MOVE FORWARD AND BACKWARD

The direction and speed of movement is controlled by the gearshift lever.

1. Start tractor with clutch/brake pedal de- pressed and gearshift lever in neutral (N) position.

2. Move gearshift lever to desired po- sition.

3. Slowly release clutch/brake pedal to start movement.

IMPORTANT: Bring tractor to a complete stop before shifting or changing gears.

Failure to do so will shorten the useful life

of your transaxle.

TO ADJUST MOWER CUTTING HEIGHT

The position of the attachment lift lever determines the cutting height.

• Grasp lift lever.

• Press plunger with thumb and move

lever to desired position.

Thecutting height rangeis approxi-

mately1-1/2to 4". The heightsare mea- suredfromthegroundto the bladetipwith theenginenotrunning. Theseheights are approximateandmayvary depending

uponsoil conditions,heightof grassand typesof grassbeingmowed.

• The averagelawnshouldbecut toap-

proximately2-1/2inchesduringthe cool seasonand toover 3 inchesduring hot months. Forhealthierandbetterlook-

ing lawns,mowoften andaftermoder- ategrowth.

• Forbestcuttingperformance,grass

over6inchesin heightshouldbe mowedtwice. Makethefirstcut rela-

tivelyhigh;the secondto desiredheight.

TO ADJUST GAUGE WHEELS

Gauge wheels are properly adjusted

when they are slightly off the ground when

mower is at the desired cutting height in

operating position. Gauge wheels then

keep the deck in proper position to help prevent scalping in most terrain conditions.

NOTE: Be sure tractor is on a flat level

surface.

1. Lower mower and adjust mower to de-

sired cutting height(See "TO ADJUST MOWER CUTTING HEIGHT' in this

section of manual).

2. Remove retainer spring and clevis pin which secure each gauge wheel bar.

3. Lower gauge wheels to ground. Raise gauge wheels slightly to align holes in bracket and gauge wheel bar and insert clevis pin. Gauge wheels should be slightly off the ground.

4. Replace retainer spring into clevis pin.

5. Be sure all gauge wheels are in the same setting.

IMPORTANT: Be sure to readjust gauge

wheels if you change the cutting height of the mower deck.

Retainer

Clevis Pin

TO OPERATE MOWER

Your tractor is equipped with an operator presence sensing switch. Any attempt by the operator to leave the seat with the engine running and the attachment clutch engaged will shut off the engine.

1. Select desired height of cut.

2. Start mower blades by engaging at- tachment clutch control.

TO STOP MOWER BLADES - disengage attachment clutch control.

,_CAUTION: Do not operate the mower

without either the entire grass catcher, on mowers so equipped, or the deflector shield in place. Attachment

Clutch Lever Attachemnt

"Engaged" gh

Position _-,,_ Position

Low

Position

"Disengaged_

Position

Shield

TO OPERATE ON HILLS

_,WARNING: Do not drive up or down

hills with slopes greater than 15° and do not drive across any slope. Use the slope guide at the back of this manual.

• Choose the slowest speed before start-

ing up or down hills.

• Avoid stopping or changing speed on

hills.

• If slowing is necessary, move throttle

control lever to slower position.

• If stopping is absolutely necessary, push

clutch/brake pedal quickly to brake posi- tion and engage parking brake.

• Move gearshift lever to 1st gear. Be

sure you have allowed room for tractor to roll slightly as you restart movement.

• To restart movement, slowly release

parking brake and clutch/brake pedal.

• Make all turns slowly.

TO TRANSPORT

• Raise attachment lift to highest position

with attachment lift control.

• When pushing or towing your tractor,

be sure gearshift lever is in neutral (N) position.

• Do not push or tow tractor at more than

five (5) MPH.

NOTE: To protect hood from damage when transporting your tractor on a truck or a trailer, be sure hood is closed and secured to tractor. Use an appropriate

means of tying hood to tractor (rope, cord, etc.).

TOWING CARTS AND OTHER ATTACH-

MENTS

Tow only the attachments that are recom-

mended by and comply with specifications of the manufacturer of your tractor. Use common sense when towing. Too heavy of a load, while on a slope, is dangerous. Tires can lose traction with the ground and cause you to lose control of your tractor.

BEFORE STARTING THE ENGINE

CHECK ENGINE OIL LEVEL

The engine in your tractor has been shipped, from the factory, already filled

with summer weight oil.

1. Check engine oil with tractor on level ground.

2. Unthread and remove oil fill cap/ dipstick; wipe oil off. Reinsert the dipstick into the tube and rest oil fill cap on the tube. Do not thread the cap

onto the tube. Remove and read oil level. If necessary, add oil until "FULL'

mark on dipstick is reached. Do not overfill.

• For cold weather operation you should

change oil for easier starting (See the oil viscosity chart in the Maintenance section of this manual).

• To change engine oil, see the Mainte-

nance section in this manual.

ADD GASOLINE

• Fill fuel tank to bottom of filler neck. Do

not overfill. Use fresh, clean, regular unleaded gasoline with a minimum of

87 octane. (Use of leaded gasoline will increase carbon and lead oxide deposits

and reduce valve life). Do not mix oil with gasoline. Purchase fuel in quan- tities that can be used within 30 days to

assure fuel freshness.

_CAUTION: Wipe off any spilled oil or fuel. Do not store, spill or use gasoline

near an open flame. IMPORTANT: When operating in temper-

atures below32°F(0°C), use fresh, clean winter grade gasoline to help insure good

cold weather starting.

CAUTION: Alcohol blended fuels (called gasohol or using ethanol or methanol) can attract moisture which leads to separa- tion and formation of acids during storage. Acidic gas can damage the fuel system of an engine while in storage. To avoid engine problems, the fuel system should be emptied before storage of 30 days or longer. Drain the gas tank, start the engine and let it run until the fuel lines and carburetor are empty. Use fresh fuel

next season. See Storage Instructions for additional information. Never use engine

or carburetor cleaner products in the fuel tank or permanent damage may occur.

TO START ENGINE When starting the engine for the first time

or if the engine has run out of fuel, it will take extra cranking time to move fuel from

the tank to the engine.

1. Sit on seat in operating position, depress clutch/brake pedal and set parking brake.

2. Place gear shift lever in neutral (N)

position.

3. Move attachment clutch to disengaged position.

4. Move throttle control to fast position

5. Pull choke control out for a cold engine start attempt. For a warm engine start attempt the choke control may not be

needed.

NOTE: Before starting, read the warm and cold starting procedures below.

6. Insert key into ignitionand turn key clockwise to start position and release key as soon as engine starts. Do not run starter continuously for more than fifteen seconds per minute. If the engine does not start after several attempts, push choke control in, wait a few minutes and try again. Ifengine

still does not start, pull the choke con- trol out and retry.

WARM WEATHER STARTING (50 ° F and above)

7. When engine starts, slowly push choke control in until the engine begins to run smoothly. If the engine starts to run roughly, pull the choke control out slightly for a few seconds and then continue to push the control in slowly.

• The attachments and ground drive can

now be used. If the engine does not

accept the load, restart the engine and allow it to warm up for one minute using the choke as described above.

COLD WEATHER STARTING (50° F and

below)

7. When engine starts, slowly push choke control in until the engine begins to run

smoothly. Continue to push the choke control in small steps allowing the en-

gine to accept small changes in speed and load, until the choke control is fully in. If the engine starts to run roughly,

pull the choke control out slightly for a

few seconds and then continue to push the control in slowly. This may require

an engine warm-up period from several seconds to several minutes, depending

on the temperature.

• The attachments can be used during the

engine warm-up period and may require

the choke control be pulled out slightly.

NOTE: If at a high altitude (above 3000 feet)

or in cold temperatures (below 32 F) the carburetor fuel mixture may need to be ad-

justed for best engine performance (see "TO ADJUST CARBURETOR" in the Service and

Adjustments section of this manual).

MOWING TIPS

• Mower should be properly leveled for

best mowing performance. See "TO LEVEL MOWER HOUSING" in the

Service and Adjustments section of this manual.

• The left hand side of mower should be

used for trimming.

• Drive so that clippings are discharged

onto the area that has already been cut. Have the cut area to the right of

the tractor. This will result in a more

even distribution of clippings and more uniform cutting.

• When mowing large areas, start by

turning to the right so that clippings will

discharge away from shrubs, fences, driveways, etc. After one or two rounds,

mow in the opposite direction making left hand turns until finished.

• Always operate engine at full throttle when mowing to assure better mowing

performance and proper discharge of material. Regulate ground speed by

selecting a low enough gear to give the

mower cutting performance as well as

the quality of cut desired.

• When operating attachments, select a ground speed that will suit the terrain and give best performance of the at- tachment being used.

MULCHING MOWING TIPS IMPORTANT: For best performance, keep

mower housing free of built-up grass and trash. Clean after each use.

• The special mulching blade will recut the grass clippings many times and

reduce them in size so that as they fall onto the lawn they will disperse into the grass and not be noticed. Also, the

mulched grass will biodegrade quickly to provide nutrients for the lawn. Always

mulch with your highest engine (blade) speed as this will provide the best recut-

ting action of the blades.

• Avoid cutting your lawn when it is wet. Wet grass tends to form clumps and

interferes with the mulching action. The

best time to mow your lawn is the early afternoon. At this time the grass has dried and the newly cut area will not be exposed to the direct sun.

• For best results, adjust the mower cutting height so that the mower cuts off only the top one-third of the grass

blades. For extremely heavy grass, re-

duce your width of cut on each pass and

mow slowly.

MAXI_

• If grass is extremely tall, it should be mowed twice to reduce load and pos-

sible fire hazard from dried clippings. Make first cut relatively high; the second

to the desired height.

• Do not mow grass when it is wet. Wet grass will plug mower and leave

undesirable clumps. Allow grass to dry before mowing.

0O272

• Certain types of grass and grass conditions may require that an area be

mulched a second time to completely

hide the clippings. When doing a sec- ond cut, mow across or perpendicular to the first cut path.

• Change your cutting pattern from week to week. Mow north to south one week

then change to east to west the next week. This will help prevent matting and graining of the lawn.

MAINTENANCE SCHEDULE

FILL IN DATES AS YOU COMPLETE

REGULAR SERVICE

Check Brake Operation Check Tire Pressure

Check Operator Presence and

T Interlock Systems a Check for Loose Fasteners

A Sharpen/Replace Mower Blades

T Lubrication Chart

0 Check Battery Level

R Clean Battery and Terminals

Check Transaxle Cooling Check V-Belts

Check Engine Oil Level Change Engine Oil (with oil filter)

E Change Engine Oil (without oil filter) U Clean Air Filter

G Clean Air Screen

_ Inspect Muffler/Spark E Replace Oil Filter (If equipped)

Clean Engine Cooling Fins Replace Spark Plug Replace Air Filter Paper Cartridge Replace Fuel Filter

t - Change more often when operating under a heavy load or

in high ambient temperatures.

2 - Se_'ice more Otten when operating in dirty or dusty conditions.

Attester

OAT:S

3 =Replace blades more often when mowing in sandy soil 4 =Not required it equipped with maiotenancertree battery. 5 =Tighten front axle pivot bolt to 35 ft.4bs, maximum.

Do not overtighten.

GENERAL RECOMMENDATIONS

The warranty on this tractor does not cover items that have been subjected to operator abuse or negligence. To receive full value from the warranty, operator

must maintain tractor as instructed in this manual.

Some adjustments will need to be made periodically to properly maintain your

tractor. All adjustments in the Service and Adjust-

ments section of this manual should be

checked at least once each season.

• Once a year you should replace the spark plug, clean or replace air filter,

and check blades and belts for wear. A new spark plug and clean air filter

assure proper air-fuel mixture and help your engine run better and last longer.

BEFORE EACH USE

1. Check engine oil level.

2. Check brake operation.

3. Check tire pressure.

4. Check operator presence and

interlock systems for proper operation.

5. Check for loose fasteners.

LUBRICATION CHART

@ Spindle -@ Spindle

Zerk Zerk

@Front Wheel @Front Wheel

Bearing Bearing Zerk

Zerk

@En

I "d)Gear- ,' ,' °_'_I I shift

....... Pivots

_SAE 30 or 10W30 Motor Oil @General Purpose Grease

@Refer to Maintenance "ENGINE" Section

IMPORTANT: Do not oil or grease the pivot points which have special nylon

bearings. Viscous lubricants will attract dust and dirt that will shorten the life of

the self-lubricating bearings. If you feel they must be lubricated, use only a dry, powdered graphite type lubricant sparingly.

TRACTOR

Always observe safety rules when per- forming any maintenance.

BRAKE OPERATION

If tractor requires more than six (6) feet stopping distance at high speed in highest gear, then brake must be adjusted. (See

"TO ADJUST BRAKE" in the Service and Adjustments section of this manual).

TIRES

• Maintain proper air pressure in all tires

(See "PRODUCT SPECIFICATIONS" section of this manual).

• Keep tires free of gasoline, oil, or insect

control chemicals which can harm rub- ber.

• Avoid stumps, stones, deep ruts, sharp

objects and other hazards that may cause tire damage.

NOTE: To seal tire punctures and prevent flat tires due to slow leaks, tire sealant

may be purchased from your local parts dealer. Tire sealant also prevents tire dry

rot and corrosion.

OPERATOR PRESENCE SYSTEM

Be sure operator presence and interlock systems are working properly. If your trac-

tor does not function as described, repair the problem immediately.

• The engine should not start unless the

clutch/brake pedal is fully depressed and attachement clutch control is in the

disengaged position.

• When the engine is running, any at-

tempt by the operator to leave the seat

without first setting the parking brake should shut off the engine.

• When the engine is running and the

attachment clutch is engaged, any at-

tempt by the operator to leave the seat

should shut off the engine.

• The attachment clutch should never op-

erate unless the operator is in the seat.

BLADE CARE

For best results mower blades must be

kept sharp. Replace bent or damaged

blades.

IMPORTANT: To ensure proper assembly, center hole in blade must align with star on mandrel assembly.

4. Reassemble blade bolt, lock washer and flat washer in exact order as

shown.

5. Tighten blade bolt securely (27-35 Ft. Lbs. torque).

IMPORTANT: Blade bolt is grade 8 heat treated.

Trailing Ec

Flat Washe_ /'

Lock _. Washer_

Blade Bolt (Grade 8)*',--,.._f

*A Grade 8 Heat Treated Bolt Can Be

Identified By Six Lines On The Bolt Head

ge Up Mandrel Assembly

jBlade

_ Star

Hole

TO SHARPEN BLADE

NOTE: We do not recommend sharp- ening blade - but if you do, be sure the

blade is balanced. Care should be taken to keep the blade

balanced. An unbalanced blade will cause excessive vibration and eventual damage

to mower and engine.

• The blade can be sharpened with a file

or on a grinding wheel. Do not attempt to sharpen while on the mower.

• To check blade balance, you will need a

5/8" diameter steel bolt, pin, or a cone

balancer. (When using a cone balancer,

follow the instructions supplied with

balancer.)

NOTE: Do not use a nail for balancing blade. The lobes of the center hole may

appear to be centered, but are not.

• Slide blade on to an unthreaded portion

of the steel bolt or pin and hold the

bolt or pin parallel with the ground. If blade is balanced, it should remain in a

horizontal position. If either end of the blade moves downward, sharpen the heavy end until the blade is balanced.

BLADE REMOVAL

1. Raise mower to highest position to al- low access to blades.

2. Remove blade bolt, lock washer and flat washer securing blade.

3. Install new or resharpened blade

with trailing edge up towards deck as shown.

5/8"Bolt or..

Center Hole

+ 42 hidden pages