Craftsman 917258452 Owner’s Manual

MODEL NU E

917.258452

Assembly Operation Customer Responsibilities

Serv.ce and ...

- i Adjustments

Repair Parts

OWNER'S MANUAL

CAUTION:

For answers to your questions

about this product, Calt:

1-800-659-5917

Sears Craftsman Help Line 5 am - 5 pm, Mon - Sat

Read and follow aH safety rules and instructions before operating this equipment.

FOR CONSUMER ASSISTANCE HOT LINE, CALL THIS TOLL FREE NUMBER: 1-800-659-5917

I1llllllrI I11111111IIIIIIIII IIIIII ...............

I1 I1/11111/II

Safe Operation Practices for Ride-On Mowers

iMPORTANT: THIS CUTTING MACHINE iS CAPABLE OF AMPUTATING HANDS AND FEET AND THROWING OBJECTS_ FAILURE TO OBSERVE THE FOLLOWING SAFETY INSTRUCTIONS COULD RESULT IN SERIOUS INJURY OR DEATH.

SAFETY RULES

t. GENERAL OPERATION

Read, understand, and foltow all instructions in the manual

and on the machine before starting.

- Only altow responsible adults, who are familiar with the instructions, to operate the machine.

Clear the area of objects such as rocks, toys, wire, etc. which could be picked up and thrown by the blade.

° Be sure the area isclear ofother peepte before mowing. Stop

machine if anyone enters the area.

o Never carry passengers.

Do not mow in reverse unless absolutely necessary. Aiways look down and behind before and while backing.

• Be aware of the mower discharge direction and do not point it at anyone. Do not operate the mower without either the

entire grass catcher or the guard in place.

• Slow down before turning.

, Never leave a running machine unattended. Always turn off

blades, set parking brake, stop engine, and remove keys before dismounting.

, Turn off blades when not mowing.

Stop engine before removing grass catcher or unclogging

chute.

• Mow only in daylight or good artificial light.

, Do not operate the machine while under the influence of

alcohot or drugs.

= Watch for traffic when operating near or crossing roadways.

• Use extra care when loading or unloading the machine into a trailer or truck.

II. SLOPE OPERATION

Slopes are a major factor related to loss-of-control and

tipover accidents, which can result in severe injury or death.

All slopes require extra caution, If you cannot back up the slope or if you feel uneasy on it, do not mow it.

DO" , Mow up and down slopes, not across.

, Remove obstacles such as rocks, tree limbs, etc.

• Watch for holes, ruts, or bumps. Uneven terrain could overturn the machine. Tall grass can hide obstacles.

• Use stow speed. Choose a low gear so that you wilt not have to stop or shift while on the slope.

o Follow the manufacturer's recommendations for wheel

weights or counterweights to improve stability.

o Use extra care with grass catchers or other attachments.

These can change the stability of the machine.

• Keep all movement on the slopes slowand gradual Do not make sudden changes in speed or direction.

• Avoid starting or stopping on a slope. If tires lose traction, disengage the blades and proceed slowly straight down the slope.

DO NOT:

. Donotturnonslopesunlessnecessary, andthen,turns!owty

and gradually downhill, if possible.

• Do not mow near drop-offs, ditches, or embankments. The

mower could suddenty turn over if a wheel is over the edge of a ctiff or ditch, or if an edge caves in.

= Do not mow on wet grass, Reduced traction could cause

sliding.

, Do not try to stabilize the machine by putting your foot on the

ground.

• Do not use grass catcher on steep slopes.

lit. CHILDREN

Tragic accidents can occur if the operator is not alert to the presence of children, Children are often attracted to the

machine and the mowing activity. Never assume that

children will remain where you last saw them,

Keep children out of the mowing area and under the watchful care of another responsible adult.

o Be alert and turn machine off if children enter the area,

Before and when backing, look behind and down for small children.

Never carry children. They may fall off and be seriously injured or interfere with safe machine operation.

Never allow children to operate the machine. Use extra care when approaching blind corners, shrubs, trees, or other objects that may obscure vision.

IV. SERVICE . Use extra care in handling gasoline and other fuels. They are

flammable and vapors are explosive.

Use only an approved container, Never remove gas cap or add fuel with the engine

running. Allow engine to cool before refueling. Do not smoke.

Never refuel the machine indoors, Never store the machine or fuel container inside where

there is an open flame, such as a water heater.

° Never run a machine inside a closed area.

• Keep nuts and bolts, especially blade attachment bolts, tight and keep equipment in good condition.

. Never tamper with safety devices. Check their proper

operation regularly.

• Keep machine free of grass, leaves, or other debris build-up. Clean oil or fuel spillage. Allow machine to cool before storing.

o Stop and inspect the equipment if you strike an object.

Repair, if necessary, before restarting.

o Never make adjustments or repairs with the engine running.

Grass catcher components are subject to wear, damage, and deterioration, which could expose moving parts or allow objects to be thrown. Frequently check components and

replace with manufacturer's recommended parts, when nec-

essary.

, Mower blades are sharp and can cut. Wrap the blade(s) or

wear gloves, and use extra caution when servicing them.

Check brake operation frequently. Adjust and service as required.

[_ .......Look for this symbol to point out im_

portant safety precautions, tt means CAUTION!!! BECOMEALERT!!! YOUR

SAFETY IS INVOLVED.

sparkplu_

wireand ptace wire where it cannot contact spark plug in order to prevent accidenta!

cAuT'o.:A,w0ysdisconnect

starting when setting up, transporting,

adjusting or making repairs.

& WARNING

The engine exhaust from this product con- tains chemicals known to the State of Califor-

nia to cause cancer, birth defects, or other

reproductive harm.

CONGRATULA'TIONS on your purchase of a Sears Tractor. it has been designed, engineered and manufac- tured to give you the best possible dependability and

performance. Shoutd you experience any probtem you cannot easily

remedy, please contact your nearest Sears Authorized Service Center/Department. We have competent, well-

trained technicians and the proper tooIs to service or repair this tractor.

Please read and retain this manual. The instructions will enable you to assemble and maintain your tractor properly.

Always observe the "SAFETY RULES".

MODEL

NUMBER 9t7.258452

SERIAL NUMBER

DATE OF PURCHASE

PRODUCT SPECMFJCATIONS

HORSEPOWER: 12.5 GASOUNE CAPACITY 1.25 GALLONS

AND TYPE: UNLEADED REGULAR OiL TYPE (API-SF/SGiSH): SAE 30 (above 32°F)

SAE 5W-30 (below 32°F)

OIL CAPACITY: 3.0 PINTS SPARK PLUG: CHAMPION RJ19LM

(GAP: .030") VALVE CLEARANCE: INTAKE: .005" - .007"

EXHAUST: .009" - .0t 1"

GROUND SPEED (MPH): FORWARD:

1st 1.0 2nd 2.1 3rd 3.1 4th 4.0 5th 5.1

REVERSE: 1.6

THE MODEL AND SERIAL NUMBERS WILL BE FOUND ON A PLATE UNDER THE SEAT.

YOU SHOULD RECORD BOTH SERIAL NUMBER AND

DATE OF PURCHASE AND KEEP 1NA SAFE PLACE FOR FUTURE REFERENCE.

MAINTENANCE AGREEMENT

A Sears Maintenance Agreement is available on this prod-

uct. Contact your nearest Sears store for details,

TIRE PRESSURE: FRONT: i4 PSi

REAR: 12 PSI

CHARGING SYSTEM: 3 AMPS BATTERY

5 AMPS HEADLIGHTS

BATTERY: AMPiHR: 25

MIN. CCA: t90 CASE SIZE: U1R

BLADE BOLT TORQUE: 30-35 FT. LBS.

WARNING: This tractor is equipped with an internal combustion engine and should not be used on or near any

unimproved forest-covered, brush-covered or grass-cov-

CUSTOMER RESPONStBILmES

,, Read and observe the safety rules.

• Foliow a regular schedule in maintaining, caring for and using your tractor.

, FoiIow the instructions under "Customer Responsibili-

ties" and "Storage" sections of this owner's manuat.

ered tand unless the engine's exhaust system is equipped with a spark arrester meeting applicable local orstate laws (if any), tfaspark arrester is used, it should be maintained in effective working order by the operator.

In the state of California the above is required by law (Section 4442 of the California Public Resources Code). Otherstates may have similar laws. Federal laws apply on federal lands. A spark arrester for the muffler is available through your nearest Sears Authorized Service Center/ Department (See REPAIR PARTS section of this manual).

LIMITED ONE YEAR WARRANTY ON CRAFTSMAN RIDING EQUIPMENT

For one (1) year from the date of purchase, if this Craftsman Riding Equipment is maintained, lubricated and tuned up according to the instructions in the owner's manuat, Sears will repair or replace, free of charge, any parts found to be defective in material or workmanship.

This Warranty does net cover:

• Expendable items which become worn during normal use, such as blades, spark plugs, air cleaners, belts, etc.

• Tire replacement or repair caused by punctures from outside objects, such as nails, thorns, stumps, or glass.

• Repairs necessary because of operator abuse, negligence, improper storage or accident or the failure to maintain the

equipment according to the instructions contained in the owner's manual.

• Riding equipment used for commercial or rental purposes.

LIMITED 90 DAY WARRANTY ON BATTERY

For ninety (90) days from date of purchase, if any battery included with this riding equipment proves defective in material or workmanship and our testing determines the battery will not hold a charge, Sears will replace the battery at no charge. IN-HOME WARRANTY SERVICE ON YOUR CRAFTSMAN RIDING EQUIPMENT IS AVAILABLE AT NO-CHARGE FOR 30 DAYS FROM THE DATE OF PURCHASE. PLEASE CONTACT YOUR NEAREST SERVICE CENTER. AFTER 30 DAYS

FROM THE DATE OF PURCHASE, WARRANTY SERVICE IS AVAILABLE BY TAKING YOUR CRAFTSMAN RIDING EQUIP- MENT TO YOUR NEAREST SEARS SERVICE CENTER. (IN-HOME WARRANTY SERVICE WiLL STILL BE AVAILABLE

AFTER 30 DAYS FROM THE DATE OF PURCHASE BUT A STANDARD TRiP CHARGE WILL APPLY.) THIS WARRANTY APPLIES ONLY WHILE THIS PRODUCT IS IN THE UNITED STATES.

This Warranty gives you specific iegat rights, and you may also have other rights which may vary from state to state.

SEARS, ROEBUCK AND CO., D/817 WA, HOFFMAN ESTATES, fL 60179

TABLE OF

CONTENTS

SAFETY RULES ............................................................ 2

PRODUCT SPECIFBCATJONS ...................................... 3

CUSTOMER RESPONSiBiLITiES ..................... 3, 14-18

WARRANTY .................................................................. 3

TRACTOR ACCESSORIES .......................................... 5

ASSEMBLY ................................................................ 7-9

OPERATION ........................................................... t0-! 3

NDEX

Accessories ........................................... 5

Adjustments:

Brake ............................................ 2I

Carburetor .................................... 24

Mower

Front-To-Back.........................20

Side-To-Side ........................... 20

Throttle Control Cable .................. 23

Air Filter, Engine .................................. 17

Air Screen, Engine .............................. 17

Assembly ............................................ 7-9

Battery:

Charging ........................................ 8

Cleaning ....................................... 16

Starting with Weak Batter,i .......... 22

Storage ........................................ 25

Terminals ..................................... t 6

Belt:

Motion Drive

Removal/Replacement ............ 2t

Mower Blade{s)

Removal/Replacement ............ 2!

Blade:

Sharpening ................................... 15

Replacement ................................ 15

Brake Adjustment ................................ 21

Carburetor Adjustment ........................ 24

Controls, Tractor ................................. 10

Customer Responsibilities .............. 15-t 8

Engine:

Air Filter .................................... 17

Air Screen, Engine ................... 17

Cooling Fins, Engine ................ !7

Engine Oil ................................ ! 6

Fuel Filter ................................. 18

Spark Plug(s) ........................... 18

Tractor:

Battery ...................................... 16

Blade ........................................ 15

Lubrication Chart ...................... 14

Maintenance Schedule ............ 14

Tire Care .......................... 8,15,22

Transaxle ................................. 16

Cutting Height, Mower ......................... 11

E_ectricaJ:

Interlocks and Relays .................. 23

Schematic .................................... 29

Wiring Diagram ............................ 30

Engine:

Air Filter ........................................ 17

Air Screen .................................... 17

Cooling Fins, Engine .................... 17

Oil Change ................................... 16

Oil Level .................................. 12,16

Oil Type ........................................ 16

Preparation .................................. 12

Repair Parts ............................ 48-52

Starting ......................................... 13

Storage ........................................ 25

Filter:

Air Filter ........................................ t7

Fuel .............................................. 18

Fuel:

Type ............................................. 12

Storage ........................................ 25

Fuse .................................................... 23

Hood Removal/Installation .................. 23

Leveling Mower Deck .......................... 20

Lubrication:

Chart ............................................ I4

Maintenance Schedule ....................... 14

Mower:

Adjustment, Front-to-Back ........... 20

Adjustment, Side-to-Side ............. 20

Biade Sharpening ........................ 15

Blade Replacement ...................... 15

Cutting Height .............................. 11

lnstafiation .................................... 19

Operation ..................................... 12

Removal ....................................... 19

Mowing Tips ........................................ '13

Muffler ................................................. 18

Spark Arrester ........................... 3,40

Oil:

Cold Weather Conditions ........ t 2,16

Engine .......................................... 16

Storage ........................................ 25

MAINTENANCE SCHEDULE ...................................... 14

SERVJCE AND ADJUSTMENTS ............................ 19-24

STORAGE ................................................................... 25

TROUBLESHOOTING ............................................ 26-27

REPAIR PARTS - TRACTOR ................................. 30-47

REPAIR PARTS - ENGINE .................................... 48-52

PARTS ORDERING/SERVICE ................ BACK COVER

Operation ....................................... 10-13

Operating Mower ................................ 12

Options:

Accessories ................... .................. 5

Spark Arrester ........................... 3,40

Parking Brake ................................. t0-11

Parts Bag .............................................. 6

Parts, Replacement/Repair ............ 30-47

Product Specifications ........................... 3

Repair Parts ................................... 30-47

Safety Rules .......................................... 2

Seat ....................................................... 8

Service and Adjustments ............... t9-24

Carburetor .................................... 24

Fuse ............. :............................... 23

Hood Removal/Installation ........... 23

Motion Drive Belt

Removal/Replacement ............ 21

Mower Belt(s}

Removal/Replacement ............ 21

Mower Adjustment

Front4o-Back .......................... 20

Side-to-Side ............................ 20

Mower Removal ........................... I9

Tire Care .............................. 8,15,22

Slope Guide Sheet .............................. 51

Spark Plug(s) ...................................... 18

Specifications ........................................ 3

Starting the Engine ........................ t2-13

Steering Wheel ................................. 7,22

Stopping the Tractor ............................ 1t

Storage ................................................ 25

Throttle Control Cable Adjustment ...... 24

Tires ............................................ 8,15,22

Trouble Shooting Chart .................. 26-27

Transaxle ............................................ t6

Warranty ................................................ 3

Wiring Diagram ................................... 30

Wiring Schematic ................................ 29

ACCESSO megAN ATTACH ENTS

These accessories and attachments were available through most Sears retail outlets and service centers when the tractor was purchased, Most Sears stores can order these items for you when you provide the model number of your tractor.

ENGINE

SPARK PLUG GAS CAN ENGINEOiL AiR FDLTEFI

FUEL STAB:_LIZER

MAINTENANCE

f BLADES BELTS

]

PERFORMANCE

Sears offers awide variety of attachments that fit your tractor. Many of these are listed below with brief explanations of how they can help you. This Listwas current at the time of publication; however, it may change infuture years - more attachments may be added, changes may be made in these attachments, or some may no longer be available or fit your model. Contact your nearest Sears store for the accessories and attachments that are available for your tractor,

Most of these attachments do not require additional hitches or conversion kits (those that do are indicated) and are designed for easy attaching and detaching.

AERATOR promotes deep root growth for a heattky lawn. Ta- pered 2.5-inch steel spikes mounted on 10-inch diameter discs puncture holes in soil at close intervals to fet moisture soak in. Steel weight tray for increased penetration.

BAGGER lets you collect grass clippings and leaves for a healthier, heater looking lawn. Two Permanex containers hold

30-gallon plastic bags.

BUMPER protects front end of tractor from damage. CARTS make hauling easy. Variety of s_zes available, plus

accessories such as side panel kits, toot caddy, cart cover, protective mat and dolly.

CORING AERATOR takes small plugs out of soil to allow mois- ture and nutrients to reach grass roots. 36-inch swath, 24 hardened steel coring tips. 150 lb. capacity weight tray.

EASY OIL DRAIN VALVE makes oil changes easier, faster. FRONT NOSE ROLLER canters in front of mower deckto reduce

chances of "scalping" on uneven terrain. GANG HITCH lets you tow 2 or3 pull-behind attachments at once,

such as sweepers, dethatchers, aerators (not for use with rollers, carts or other heavy attachments).

GAUGE WHEELS on both sides of the mower deck reduce

chances of "scalping" on uneven terrain. For mower decks not so

equipped. MULCH RAKE/DETHATCHER loosens soil and flips thatch and

matted leaves to lawn surface for easy pickup. Twenty spring tine teeth. Usefulto prepare bare areas forseeding. Availablefor front or rear mounting. HIGH PERFORMANCE REEL-ACTION SPRING TINE DETHATCHER covers 364nch wide path and tosses thatch into large hopper. Mounts behind tractor.

MULCHING CLOSE-OUT PLATE KIT, once installed, lets you mulch, discharge or bag clippings (bagger optional) without

changing blades. For models not equipped as 3-in-1 Convertible mowers. See "MOWER" in the Repair Parts section of this manual.

RAMP TOPS AND FEET let you load and unload tractor from a pickup truck. Use with 2 x 8 or 2 x 10 tumber.

ROLLER for smoother lawn surface. 36-inch wide, 18-inch diameterwater-fight drum holds up to 390 lbs. of weight. Rounded

edges prevent harm to tuff. Adjustable scraper automatically

cleans drum.

SNOW BLADE forsnow removal only. 14-inch high, 48-inch wide

btade clears 42-inch path when angled left or right. Raises, lowers with side lever. Adjustable skids; replaceable, reversible scraper bar. (Use with tire chains and wheeI weights and/or rear drawbar weight.)

SNOWTHROWER has 40-inch swath. Drum-type auger handles powdery and wet/heavy snow. Mounts easily with simple pin

arrangement. Discharge chute adjusts from tractor seat. 6-inch diameter spout discharges snow t0 to 50 feet. Lift controlled at tractor seat. (Use witt_ chains and whee! weights and/or rear drawbar weight.)

SPRAYERS use 12-volt DC electric motor that connects to the tractor battery or other !2-volt source. Includes booms for

automatic spraying and hand held wand for spot spraying. Wand has adjustable spray pattern. For applying herbicides, insecti- cides, fungicides and liquid fertilizers.

SPREADER!SEEDERS make seeding, fertilizing, and weed kill- ing easy. Broadcast spreaders are also useful for granular de-

icers and sand. SWEEPERS let you collect grass clippings and leaves.

TILLER has 5hp engine and 36-inch swath to prepare seed beds, cultivate and compost garden residue. Tiller has its own built-in

lift and depth controi system and does NOT require a sleeve hitch. Fits any lawn, yard or garden tractor. Simply hook up to the tractor

drawbar and go! Optional accessories convert unit for dethatching, aerating, hiiiing...without tools.

TIRE CHAINS are heavy duty; closely spaced extra-large cross links give smooth ride, outstanding traction.

TRACTOR CAB has heavy duty vinyI fabric over tubular steel frame, ABS plastic top; clear plastic windshield offers 360 degree

visibility. Hinged metal doors with catch. Keeps operator warm and dry. Remove vinyl sides and windshields for use as sun

protector in summer. Optional accessories include: tinted/

tempered solid safety glass windshield with hand operated wiper;

12-vott amber caution light for mounting on cab top.

VACS for powerfu! collection of heavy grass clippings and leaves. Optional wand attachment to pick up debris in hard-to-reach places. VAC/CHIPPER includes a chipper-shredder.

WEIGHT BRACKET for drawbar for snow removal applications.

Uses (1) 55 Ib. weight.

WHEEL WEIGHTS for rear wheels provide needed traction for snow removal or dozing heavy materials.

CONTENTS OF HA DWA E PACK

Parts Bag contents shown fuji size

(2) Sheet

Metal

Screws

#10-t6 x 1/2

(1) Large Flat Washer _ 1)

(1) Locknut 3/8-24

(1) Hex Bolt 112-13x 1

Parts packed separately Jn carton

Steering

Wheel

Steering

Boot

Manual Parts Bag

Video

Cassette

f i

(1) Shoulder Bolt 5/16-18

(1) Lock Washer 1/2

(t) Washer 17/32 x t-3/t6 x 12 Gauge

(2) Hex Bolts 1/4-20 x 3/4

(2) Hex Nuts t/4-20

__1 (2) Lock Washers !/4

Parts bag contents not shown full size

_ f Steering

'-_ \ • Wheel

Steering Wheel ,,

Adapter

_ teering

Bushing

Insert

(2) Keys

(2) Washers 9/32 x 5/8 x 16 Gauge

Slope Sheet

ASSEMBLY

Your new tractor has been assembled at the factory with exception of those parts left unassembied for shipping purposes.

To ensure safe and proper operation of your tractor aIl parts and hardware you assemble must be tightened securely. Use the correct tools as necessary to insure proper tightness.

TOOLS REQUIRED FOR ASSEMBLY

A socket wrench set will make assembly easier. Standard wrench sizes are listed.

(1) 5/t6" wrench (I) 9/!6" wrench (2) 7/16" wrenches Tire pressure gauge (1) 1/2" wrench Utility knife (1) 3/4" wrench

When right and left hand are mentioned in this manual, it

means when you are in the operating position (seated behind the steering wheel).

TO REMOVE TRACTOR FROM CARTON

UNPACK CARTON

• Remove all accessible loose parts and parts cartons from carton (See page 6).

o Cut along lines on carton, from top to bottom, all four

corners of carton and lay panels flat.

- Check for any additional loose parts or cartons and

remove.

BEFORE ROLMNG TRACTOR OFF SKiD

ATTACH STEERING WHEEL (See Fig. 1)

, Slide the steering bushing over the steering shaft. , Raise steering shaft forward until screw holes in dash

line up with steering bushing, install two (2) sheet metal screws and tighten securely.

, Position steering boot over steering shaft. , Place tabs of steering boot over tab slots in dash and

push down to secure.

• Slide steering wheel adapter onto upper steering shaft.

,, Position front wheels of the tractor so they are pointing

straight forward. Position steering wheel so cross bars are horizontal

(left to right) and slide onto adapter.

• Assemble large fiat washer and 3/8-24 locknut and

tighten securely.

, Snap steering wheel insert into center of steering

wheel. Remove protective materials from tractor hood and

grill.

IMPORTANT:CHECK FOR AND REMOVE ANY STAPLES IN SKID THAT MAY PUNCTURETIRESWHERETRACTOR tS TO ROLL OFF SKID.

TO ROLL TRACTOR OFF SKiD (SEE OPERA- TION SECTION FOR LOCATRON AND FUNC-

TiON OF CONTROLS)

,, Press tift lever plunger and raise attachment lift lever to

its highest position.

• Release parking brake by depressing clutch/brake pedal.

• Place gearshift lever in neutral (N) position.

o Rolt tractor backwards off skid. o Remove banding holding discharge guard up against

tractor.

STEERING " .......................i....

WHEEL 1

ADAPTER

STEERING

BOOT

STEERING SHAFT

POSITION)

STEER{NG ' '

(SHIPPING ( TAB

PosmoN) .......... 2:22_;.... ,', SLOT

FIG. 1

HOW TO SET UP YOUR TRACTOR

CONNECT BATTERY (See Figs. 2 and 3)

CAUTION: Do not short battery termi- nals by allowing a wrench or any other object to contact both terminals at the same time. Before connecting battery, remove metal bracelets, wristwatch

bands, rings, etc. Positive terminal must be connected

first to prevent sparking from acciden- tal grounding.

Remove cardboard packing from seat pan and lift seat pan to raised position.

• Open battery box door and remove protective plastic. Remove terminal protective caps and discard.

, if this battery is put into service after month and year

indicated on label (label located between terminals) charge batten.7for minimum of one hour at 6-! 0 amps.

First connect RED battery cable to positive (+) terminal with hex bolt, flat washer, lock washer and hex nut as

shown. Tighten securely.

o Connect BLACK grounding cable to negative (-) termi-

nal with remaining hex bolt, flat washer, lock washer and hex nut. Tighten securely.

,, Close battery box door.

• STEERING BUSHING

TABS ,_REW

ASSE

BLY

Open battery box door for: _ inspection for secure connections (to tighten hard-

ware).

Inspection for corrosion.

o Testing battery.

Jumping (if required).

Periodic charging.

TIVE CAPS

_[_ ISCARD TERMINAL PROTEC-

POSITIVE NEGATIVE (RED) CABLE (BLACK) CABLE

HEX FLAT

WASHER

HEX BOLT

FiG. 2

SEAT PAN

Slide seat until a comfortable position is reached which allows you to press clutch/brake pedal allthe way down

(See Fig. 8).

Get off seat without moving its adjusted position.

Raise seat and tighten adjustment bolt securely.

CHECK TIRE PRESSURE

The tires on your tractor were overinfiated at the factory for shipping purposes. Correct tire pressure is important for

best cutting performance.

- Reduce [ire pressure to PSi shown in "PRODUCT SPECIFICATIONS" on page 3 of this manual.

CHECK DECK LEVELNESS

For best cutting results, mower housing should be properly leveled. See "TO LEVEL MOWER HOUSING" in the

Service and Adjustments section of this manual.

CHECK FOR PROPER POSiTiON OF ALL BELTS

See the figures that are shown for replacing motion and mower blade drive belts in the Service and Adjustments

section of this manual. Verify that the belts are routed correctly.

CHECK BRAKE SYSTEM

After you learn how to operate your tractor, check to see

that the brake is properly adjusted. See "TO ADJUST

BRAKE" in the Service and Adjustments section of this manual.

BOX DOOR

FMG.3

_NSTALL SEAT (See Fig. 4)

Adjust seat before tightening adjustment boit.

o Remove cardboard packing on seat pan.

Place seat on pan and assemble shoulder bolt. Tighten shoulder bolt securely.

o Assembfe adjustment bolt, Iockwasher and flat washer

loosely. Do not tighten.

o Lower seat into operating position and sit on seat.

SEAT PAN

SHOULDER BOLT

ADJUSTMENT

BOLT

FIG, 4 8

FLAT WASHER

LOCK WASHER

,/CHECKLIST

BEFORE YOU OPERATE AND ENJOY YOUR NEW

TRACTOR, WE WISH TO ASSURE THAT YOU RECEIVE THE BEST PERFORMANCE AND SA TfSFA CTtON FROM

THIS QUALITY PRODUCT. PLEASE REVIEW THE FOLLOWING CHECKLIST: v" All assembly instructions have been completed. ,/ No remaining loose parts in carton.

¢" Battery is properly prepared and charged. (Minimum

! hour at 6 amps).

v" Seat is adjusted comfortably and tightened securely. v" All tires are properly inflated. (For shipping purposes,

the tires were overinflated at the factory).

v" Be sure mower deck is properly leveled side-to-side/

front-to-rear for best cutting results. (Tires must be properly inflated for leveling).

v" Check mower and drive belts. Be sure they are routed

properly around pulleys and inside all belt keepers.

v" Check wiring. See that all connections are still secure

and wires are properly clamped.

WHILE LEARNING HOW TO USE YOUR TRACTOR, PAY

EXTRA A 7TENTION TO THE FOLLOWING IMPORTANT

ITEMS:

v" Engine oil is at proper level.

v" Fuel tank is filled with fresh, clean, regular unleaded

gasoline.

,/ Become familiar with all controls _their location and

function. Operate them before you start the engine.

v" Be sure brake system is in safe operating condition.

OPERATIO

These symbols may appear on your tractor or in literature supplied with the product. Learn and understand their meaning.

BATTERY CAUTION OR REVERSE FORWARD FAST SLOW

WARNING

ENGINE ON ENGINE OFF OIL PRESSURE CLUTCH LIGHTS ON

FUEL

CHOKE MOWER HEIGHT DIFFERENTIAL PARKING BRAKE UNLOCKED

LOCK LOCKED

REVERSE NEUTRAL HIGH

LOW PARKING BRAKE

OVER TEMP

LIGHT

MOWER LIFT

DANGER, KEEP HANDS AND FEET AWAY

ATTACHMENT

CLUTCH ENGAGED

ATTACHMENT

CLUTCH DISENGAGED

IGNITION

HYDROSTATIC FREE WHEEL

(Hydro Models only)

OPERA 0

KNOW YOUR TRACTOR

READ THiS OWNER'S MANUAL AND SAFETY RULES BEFORE OPERATING YOUR TRACTOR

Compare the itlustrations with your tractor to familiarize yourseif with the locations of various controls and adjustments. Save this manual for future reference.

THROTTLFJCHOKE

CONTROL

CLUTCH!BRAKE PEDAL

ATTACHMENT SW_TCH CLUTCH LEVER

IGNITION

LIGHT SWITCH

LIFT LEVER PLUNGER

ATTACHM ENT LIFT LEVER

MOWER DECK HEIGHT ADJUST-

MENT POSITIONS

PARKING BRAKE

GEARSHIFT '

LEVER

Our tractors conform to the safety standards of the American Nationaf Standards Institute.

ATTACHMENT CLUTCH LEVER: Used to engage the mower blades, or other attachments mounted to your

tractor. LIGHT SWITCH: Turns the headlights on and off.

THROTTLE/CHOKE CONTROL: Used for starting and controlling engine speed.

CLUTCH/BRAKE PEDAL: Used fordectutching and brak - ing the tractor and starting the engine.

PARKING BRAKE: Locks clutch/brake pedai into the brake position.

FIG. 5

GEARSHIFT LEVER: Selects the speed and direction of tractor.

ATTACHMENT LIFT LEVER: Used to raise, lower and adjust the mower deck or other attachments mounted to

your tractor.

MFT LEVER PLUNGER: Used to release attachment lift

lever when changing its position.

IGNITION SWITCH: Used for starting and stopping the

engine.

OPERATION

The operation of any tractor can resu}t in foreign objects thrown into the eyes, which

can resuit in severe eye damage. Always wear safety gtasses or eye shields white operating your tractor or performing any adjustments or repairs. We recommend awide

vision safety mask over the spectacles or standard safety glasses.

HOW TO USE YOUR TRACTOR

TO SET PARKING BRAKE (See Fig, 6)

Your tractor is equipped with an operator presence sensing switch. When engine is running, any attempt by the operator to leave the seat without first setting the parking brake wilt shut off the engine.

• Depress clutch/brake pedal into full "BRAKE" position and ho_d°

Place parking brake lever in "ENGAGED" position and

release pressure from clutch/brake pedal. Pedal should remain in "BRAKE" position. Make sure parking brake

will hold tractor secure.

THROTTLE/CHOKE CONTROL

CLUTCHIBRAKE PEDAL "DRIVE" POSITION

STOPPING (See Fig. 6)

MOWER BLADES -

• Move attachment clutch lever to "DISENGAGED" po- sition.

GROUND DRIVE -

• Depress clutch/brake pedal into full "BRAKE" position.

• Move gearshift lever to neutral (N) position.

ENGINE , Move throttle control to slow position.

NOTE: Failure to move throttle control to slow position and allowing engine to idle before stopping may cause engine

to "backfire".

Turn ignition key to "OFF" position and remove key. Atways remove key when leaving tractor to prevent

unauthorized use.

• Never use choke to stop engine.

ATTACHMENT CLUTCH LEVER

"ENGAGED" POSITION

"DISENGAGED"

POSITION

PARKING BRAKE "ENGAGED" POSITION

"DISENGAGED"

POSITION

GEARSHIFT LEVER

FIG. 6

NOTE: Under certain conditions when tractor is standing idle with the engine running, hot engine exhaust gases may cause "browning" of grass. To eliminate this possibility, always stop engine when stopping tractor on grass areas.

tract_'_-r=c-om_

Aiwoysstop

described above, before _eav-

_ ing the operator's position; to empty

her, etc.

TO USE THROTTLE CONTROL (See Fig. 6)

Always operate engine at full throttle.

• Operating engine at less than full throttle reduces the battery charging rate.

o Full throttle offers the best bagging and mower perfor-

mance.

TO MOVE FORWARD AND BACKWARD (See Fig. 6}

The direction and speed of movement is controlled by the gearshift lever.

- Start tractor with clutch/brake pedal depressed and gearshift lever in neutral (N) position.

o Move gearshift lever to desired position.

• S{owty release clutch/brake pedai to start movement. IMPORTANT: BRING TRACTOR TO A COMPLETE STOP

BEFORE SHIFTING OR CHANGING GEARS. FAILURE TO DO S© WILL SHORTEN THE USEFUL LIFE OF YOUR

TRANSAXLE.

TO ADJUST MOWER CUTTING HEIGHT

(See Fig. 5)

The position of the attachment lift lever determines the cutting height.

= Grasp lift lever.

• Press plunger with thumb and move lever to desired position.

Thecutting height range is approximately 1-1/2to 4". The

heights are measured from the ground to the blade tip with

the engine not running. These heights are approximate

and may vary depending upon soil conditions, height of grass and types of grass being mowed.

, The average lawn should be cut to approximately 2-1/2

inches during the cool season and to over 3 inches

during hot months. For healthier and better looking

lawns, mow often and after moderate growth.

, For best cutting performance, grass over 6 inches in

height should be mowed twice. Make the first cut relatively high; the second to desired height.

OPERATION

TO OPERATE MOWER (See Fig. 7)

Your tractor isequipped with an operator presence sensing switch. Any attempt by the operator to leave the seat with the engine running and the attachment clutch engaged wiil

shut off the engine. o Select desired height of cut.

° Start mower blades by engaging attachment dutch

control.

o TO STOP MOWER BLADES - disengage attachment

clutch control.

ATTACHMENT CLUTCH LEVER "DISENGAGED" POSITION

"ENGAGED" POSITION

ATTACHMENT LIFT LEVER HIGH POSITION

LOW POSITION

o To restart movement, slowly reiease parking brake and

clutch/brake pedal.

o Make all turns slowly

TO TRANSPORT

Raise attachment lift to highest position with attach- ment tift controi,

o When pushing ortowing your tractor, be sure gearshift

lever is in neutrat (N) position.

• Do not push or tow tractor at more than five (5) MPH. NOTE: To protect hood from damage when transporting

your tractor on atruckor atrailer, besure hood isclosed and secured to tractor. Use an appropriate means of tying hood

to tractor (rope, cord, etc.).

BEFORE STARTING THE ENGINE

CHECK ENGINE OiL LEVEL (See Fig, 12)

- The engine in your tractor has been shipped, from the

factory, already filled with summer weight oil.

- Check engine oil with tractor on level ground.

- Remove oil fiIlcap/dipstick and wipe clean, reinsert the

dipstick and screw cap tight, wait for a few seconds,

remove and read oil level. If necessary, add oil until

"FULL" mark on dipstick is reached. Do not overfill.

* For cotd weather operation you shoutd change oil for

easier starting (See "OIL VISCOSITY CHART" in the Customer ResponsibiIities section of this manual).

- To change engine oil, see the Customer Responsibili-

ties section in this manual.

R.H.

RUNNER

/ DISCHARGE

/ GUARD

FiG. 7

TO OPERATE ON HILLS

Choose the slowest speed before starting up or down hills.

, Avoid stopping or changing speed on hills.

• If slowing is necessary, move throttle control lever to slower position.

If stopping is absolutely necessary, push clutch/brake pedat quickly to brake position and engage parking

brake. Move gearshift lever to 1st gear. Be sure you have

allowed room for tractor to rol! slightly as you restart movement.

ADD GASOLINE

• Fill fuet tank. Use fresh, clean, regular unleaded gasoline with a minimum of 87 octane. (Use of leaded

gasoline will increase carbon and lead oxide deposits and reduce valve life). Do not mix oil with gasoline,

Purchase fuel in quantities that can be used within 30

days to assure fuel freshness.

iMPORTANT: WHEN OPERATING iN TEMPERATURES BELOW 32°F(0"C), USE FRESH, CLEAN WINTER GRADE

GASOLINE TO HELP iNSURE GOOD COLD WEATHER STARTING.

WARNING: Experience indicates that alcohol blended fuels (called gasohol or using ethanol or methanol) can

attract moisture which leads to separation and formation of acids during storage. Acidic gas can damage the fuel system of an engine while in storage. To avoid engine

problems, the fuel system should be emptied before stor- age of 30 days or longer. Drain the gas tank, start the engine and let it run until the fuel lines and carburetor are

empty. Use fresh fuel next season. See Storage Instruc- tions for additional information. Never use engine or

carburetor cleaner products in the fuel tank or permanent damage may occur.

_: Fill to bottom of gas tank

_ fil_erneck. Do notoverfil!. Wipeoffany

! _ spilled oil or fuel Do not store, spill or

use gasoline near an open flame.

__ ____ .

OPERATEON

TO START ENGINE (See Fig. 6)

When starting the engine for the first time or if the engine has run out of fuel, it wili take extra cranking time to move

fuel from the tank to the engine. o Sit on seat in operating position, depress clutch/brake

pedal and set parking brake. o Piace gear shift lever in neutral (N) position. o Move attachment clutch to "DISENGAGED" position. ° Move throttle control to choke position.

Note: Before starting, read the warm and coid starting procedures below.

Insert key into ignition and turn key clockwise to"START"

position and release key as soon as engine starts. Do

not run starter continuously for more than fifteen sec-

onds per minute. If the engine does not start after

several attempts, move throttle control to fast position,

wait a few minutes and try again. If engine still does not

start, move the throttle control back to the choke

position and retry. WARM WEATHER STARTING (50° F and above)

• When engine starts, move the throttle control to the fast

position. . The attachments and ground drive can now be used. If

the engine does not accept the load, restart the engine

and allow it to warm up for one minute using the choke

as described above. COLD WEATHER STARTING ( 50° F and below)

° When engine starts, allow engine to run with the throttle

control in the choke position until the engine runs

roughly, then move throttle control to fast position. This

may require an engine warm-up period from several

seconds to several minutes, depending on the tem-

perature.

o The attachments carl also be used during the engine

warm-up period.

NOTE: if at a high altitude (above 3000 feet) or in cotd

temperatures (below 32 F) the carburetor fuel mixture may need to be adiusted for best engine performance. See "TO

ADJUST CARBURETOR" in the Service and Adjustments section of this manual.

MOWING TiPS

• Tire chains cannot be used when the mower housing is attached to tractor.

• Mower should be properly leveled for best mowing performance. See "TO LEVEL MOWER HOUSING" in the Service and Adjustments section of this manual.

o Use the runner on the right hand side of mower as a

guide. The blade cuts approximately an inch outside the runner (See Fig. 7)

- The left hand side of mower should be used for trim* ruing.

o Drive so that clippings are discharged onto the area

that has been cut. Have the cut area to the right of the

machine. This will result in a more even distribution of

clippings and more uniform cutting.

° When mowing large areas, start by turning to the right

so that clippings witl discharge away from shrubs, fences, driveways, etc. After one or two rounds, mow

in the opposite direction making left hand turns until finished (See Fig. 8).

• If grass is extremely tat!, it should be mowed twice to reduce toad and possible fire hazard from dried clip- pings. Make first cut relatively high; the second to the

desired height.

• Do not mow grass when it is wet. Wet grass will piug mower and leave undesirable clumps. Allow grass to

dry before mowing.

o Always operate engine at full throttle when mowing to

assure better mowing performance and proper dis- charge of material. Regulate ground speed by select- ing a low enough gear to give the mower cutting performance as well as the quality of cut desired.

° When operating attachments, select a ground speed

that will suit the terrain and give best performance of the attachment being used.

FIG. 8

CUSTO E ESPONS

MAINTENANCE SCHEDULE

FILL 1N DATES AS YOU COMPLETE REGULAR SERVICE

Check Brake Operation

Check Pressore IJ IV' !

Check for Loose Fasteners $f _€_7 Sharpen/Replace Mower Blades

Lubrication Chart Check Battery Level/Recharge Clean Battery and Terminals

Check Transaxte Cooling

Adjust Blade Belt{s) Tension Adjust Motion Drive Beit(s) TensTon

Check Engine Off Level Change Engine Oil

Clean Air Filter

CIean Air Screen Inspect Muffler/Spark Attester

Replace Oil Fitter (If equipped) Clean Engine Cooling Fins _#_2 Replace Spark Plug _ 6/'

Replace Air Fitter Paper Cartridge 16_'2

Replace Fue, Filter i _ ....

1 - Change more often when operating under a heavy load or in high ambienl temperatures. 2 _Service more ofte_ when operating in dirty or dusty conditions.

3 _if equipped with oil fi_ter,change oif every 50 hours. 4 - RepIace bfades more often when mewing Jnsandy soil.

v' e/

! jr'

LmES

SERVICE DATES

'3.................

5. ifequippedwith adjustablesystem. 6- Not requiredif equipped withma}ntenance-freebattery.

7- Tightenfront axlepivot boltto 35 ftAbs, maximum.

Do notovertighten.

GENERAL RECOMMENDATIONS

The warranty on this tractor does not cover items that have

been subjected to operator abuse or negligence. To receive full value from the warranty, operator must maintain

tractor as instructed in this manual. Some adjustments wilt need to be made periodically to

properly maintain your tractor. AI! adjustments in the Service and Adjustments section of

this manual should be checked at least once each season.

Once a year you should replace the spark plug, clean or replace air filter, and check blades and belts for wear. A new spark plug and clean air filter assure proper air-fuel mixture and help your engine run better

and last longer.

BEFORE EACH USE

, Check engine oil level. , Check brake operation.

• Check tire pressure.

• Check for loose fasteners.

LUBRICATION CHART

C) SPINDLE ZERK _ _ SPINDLE ZERK (_

(_) FRONT

BEARING ZERK BEARING ZERK

ENGINE (_)

CLUTCH PIVOT(S)

(_ SAE 30 OR (_) GENERAL PURPOSE GREASE

REFER TO CUSTOMER RESPONSIBILITIES "ENGINE" SECTION

IMPORTANT: DO NOT OIL OR GREASE THE PIVOT POINTS WHICH HAVE SPECIAL NYLON BEARINGS. VISCOUS LUBRI- CANTS WILL ATTRACT DUST AND DiRT THAT WILL SHORTEN THE LiFE OF THE SELF-LUBRICATING BEARINGS. IF YOU FEEL THEY MUST BE LUBRICATED, USE ONLY A DRY, POW- DERED GRAPHITE TYPE LUBRICANT SPARINGLY.

10W30 MOTOR OiL

CUSTOM RESPO

TRACTOR

Always observe safety rules when performing any mainte-

nance.

BRAKE OPERATION

If tractor requires more than six (6} feet stopping distance

at high speed in highest gear, then brake must be adjusted.

(See "TO ADJUST BRAKE" in the Service and Adjust-

ments section of this manual).

TIRES

o Maintain proper air pressure in all tires (See "PROD-

UCT SPECIFICATIONS" on page 3 of this manual).

o Keep tires free of gasoline, oil, or insect control chemi-

cals which can harm rubber.

o Avoid stumps, stones, deep ruts, sharp objects and

other hazards that may cause tire damage.

NOTE: To seat tire punctures and prevent flat tires due to slow leaks, tire sealant may be purchased from your local

parts dealer. Tire sealant also prevents tire dry rot and

corrosion,

BLADE CARE

For best results mower blades must be kept sharp. Re- ptace bent or damaged btades.

BLADE REMOVAL (See Fig. 9)

o Raise mower to highest position to allow access to

blades. Remove hex bolt, lock washer and fiat washer securing

blade.

Instal1new or resharpened blade with trailing edge up

towards deck as shown,

Reassemble hex bolt, lock washer and flat washer in

exact order as shown. Tighten bolt securely (30-35 Ft. Lbs. torque).

IMPORTANT: BLADE BOLT ISGRADEBHEATTREATED. NOTE: We do not recommend sharpening blade - but ifyou

do, be sure the bIade is balanced.

SI IL IES

BLADE

FLAT WASHER

LOCK WASHER

HEXBOLT

(GRADE

*A GRADE 8 HEAT TREATED BOLT CAN BE

IDENTIFIED BY SgX LINES ON THE BOLT HEAD.

FIG. 9

TO SHARPEN BLADE (See Fig. 10)

Care should be taken to keep the blade balanced. An unbalanced biade will cause excessive vibration and even-

tual damage to mower and engine. = The btade can be sharpened with afile or on a grinding

wheel. Do not attempt to sharpen while on the mower.

o To check blade balance, you will need a 5/8" diameter

steel bolt, pin, or a cone balancer. (When using acone balancer, follow the instructions supplied with bal- ancer).

• Slide blade on to an unthreaded portion of the steel bolt or pin and hold the bolt or pin parallel with the ground.

If blade is balanced, it should remain in a horizontal

position. If either end of the blade moves downward, sharpen the heavy end until the blade is balanced.

NOTE: Do not use a nail for balancing blade. The lobes of

the center hole may appear to be centered, but are not.

CENTER HOLE / /'

/ /

5/8" BOLT OR PiN

BLADE

FIG. 10

CUSTO ER

ESPONSJBILITIES

_!}ATTERY

Your tractor has a battery charging system which is suffi- cient for normal use. However, periodic charging of the

battery with an automotive charger will extend its life. o Keep battery and terminais clean,

o Keep battery bolts tight,

Keep small vent holes open. Recharge at 6-10 amperes for 1 hour.

TO CLEAN BATTERY AND TERMINALS Corrosion and dirt on the battery and terminals can cause

the battery to "leak" power. o Open battery box door.

Disconnect BLACK battery cable first then RED bat-

tery cable and remove battery from tractor.

Rinse the battery with ptain water and dry.

o Clean terminals and battery cable ends with wire brush

until bright. Coat terminals with grease or petroleum jelly,

o Reinstall battery (See "CONNECT BATTERY" in the

Assembly section of this manual).

V-BELTS

Check V-belts for deterioration and wear after I00 hours of operation and replace if necessary. The belts are not

adjustable. Replace belts if they begin to slip from wear.

TRANSAXLE COOLING

Keep transaxle free from buitd-up of dirt and chaff which can restrict cooling,

ENGINE

NOTE: Although multi-viscosity oils (5W30, 10W30 etc.) improve starting in cold weather, these multi-viscosity oils

wilt result in increased oil consumption when used above 32°R Check your engine oil level more frequently to avoid

possible engine damage from running tow on oil, Change the oil after every 25 hours of operation or at least

once a year if the tractor isnot used for 25 hours in one year, Check the crankcase oil level before starting the engine

and after each eight (8) hours of operation. Tighten oil fill cap/dipstick securely each time you check the oil level.

TO CHANGE ENGINE OIL (See Figs. 11 and 12) Determine temperature range expected before oil change.

All oil must meet API service classification SF, SG, or SH.

Be sure tractor is on level surface. Oit will drain more freety when warm,

Catch oil in a suitable container.

,!1

Remove oit fill cap/dipstick. Be careful not to allow dirt. to enter the engine when changing oit.

. Remove drain piug.

- After oil has drained completely, replace oil drain plug and tighten securely.

. Refill engine with oil through oil fill dipstick tube. Pour

slowly. Do not overfill. For approximate capacity see "PRODUCT SPECIFICATIONS" on page 3 of this

manual.

• Use gauge on oil fill cap/dipstick for checking level. Be sure dipstick cap is tightened securely for accurate

reading. Keep oil at "FULL" line on dipstick.

OIL FILL CAP!DIPSTICK

LUBRICATION

Only use high quality detergent oil rated with API service classification SF, SG, or SH. Select the oil's SAE viscosity

grade according to your expected operating temperature.

SAE VISCOSITY GRADES

.20 ° 0 ° 30 ° 32 ° 40 ° 60 _ 80° 100 _

.30 o _20° .10 o 6° 10° 20° 30° 40 °

TEMPERATURE RANGE ANTICIPATED BEFORE NEXT OIL CHANGE

FIG. 11

OIL DRAIN

PLUG

FIG. 12

CUS'['OME RESPONS! RL ES

A1R FILTER (See Fig, 13)

Your engine will not run properly using a dirty air filter.

Clean the foam pre-cleaner after every 25 hours of opera-

tion or every season. Service paper cartridge every 100

hours of operation or every season, whichever occurs first. Service air cleaner more often under dusty conditions. o Remove knob(s) and cover.

TO SERVICE PRE-CLEANER

• Slide foam pre-cteaner off cartridge.

• Wash it in liquid detergent and water.

• Squeeze it dry in a clean cloth. o Saturate it in engine oil. Wrap it in clean, absorbent

cloth and squeeze to remove excess oil.

• If very dirty or damaged, replace pre-cteaner. o Reinstall pre-cleaner over cartridge.

Reinstall cover and secure with knob(s).

TO SERVICE CARTRIDGE , Remove cartridge nut.

• Carefully remove cartridge to prevent debris from en-

tering carburetor. Clean base carefully to prevent debris from entering carburetor.

• Clean cartridge by tapping gently onfiat surface. If very

dirty or damaged, replace cartridge.

• Reinstall cartridge, nut, precIeaner, cover and secure

with knob(s).

IMPORTANT: PETROLEUM SOLVENTS, SUCH AS KEROSENE, ARE NOT TO BE USED TQ CLEAN THE

CARTRIDGE. THEY MAY CAUSE DETERIORATION QF THE CARTRIDGE. DO NQTOIL CARTRIDGE. DO NOT

USE PRESSURIZED AIR TO CLEAN OR DRY CARTRIDGE.

CLEAN AIR SCREEN (See Fig. 14)

Air screen must be kept free of dirt and chaff to prevent engine damage from overheating. Clean with a wire brush

or compressed air to remove dirt and stubborn dried gum fibers.

ENGINE COOLING FiNS (See Fig. 14

Remove any dust, dirt or oil from engine cooling fins to prevent engine damage from overheating.

• Remove screws from blower housing and lift housing and dipstick tube assembly off engine.

Cover oil fill opening to prevent entry of dirt.

o Use compressed air or stiff bristle brush to thoroughly

clean engine cooling fins.

• To reassemble, reverse above procedure.

SCREWS

DIPSTICK TUBE

ASSEMBLY

BLOWER HOUSING

SCREWS

AiR SCREEN

SPARK PLUG

FOAM PRE-CLEANER

ENGINE COOLING FINS

FIG. 14

CARTRtDGENUT

PAPER CARTRIDGE

FIG, 13

+ 39 hidden pages