Craftsman 875199830 Owner’s Manual

Owner's Manual

Pneumatic 1/2" Drive

IMPACT WRENCH

Model No.

875.199830

WARNING:

Before operating tool, read this
manual and follow all

Safety Recommendations and
Operating Instructions.

Safety
Warranty

Features & Operation

Maintenance

EspaSol

Distributed by Sears,

www.Sears.com

Roebuck and Co.,

Hoffman

Estates,

IL 60179

Read Operating Instructions

Please become familiar with all the instructions and

warnings before operating any pneumatic tool.
Always Wear Approved Eye Protection

Impact resistant eye protection should meet or exceed

the standards set forth in ANSI Z87.1, Occupational and

Educational Eye and Face Protection. Look for marking
Z87.1 on your eye protection to ensure that it is an
approved style.

Hearing Protection is Recommended

Hearing protection should be used when the noise level
exposure equals or exceeds an 8 hour time-weighted

average sound level of 85dBA. Process noise, reflective
surfaces, other tools being operated nearby, all add to
the noise level in a given work area. If you are unable to
determine your noise level exposure, we recommend the

use of hearing protection.
Avoid Prolonged Exposure to Vibration

Pneumatic tools can vibrate during use. Prolonged
exposure to vibration or very repetitive hand and arm

movements can cause injury. Discontinue the use of any
tool if you experience tingling, numbness, discomfort or

pain in your hands or arms. You should consult your
physician before resuming use of tool.

90 PSI Maximum
This tool is designed to operate at an air pressure of 90

pounds per square inch gauge pressure (90 PSI)

maximum, at the toot. Use of higher air pressure can,
and may cause injury. Also, the use of higher air pressure
places the internal components under loads and
stresses they were not designed for, causing premature

tool failure.
NOTE: THEAIR SUPPLYSHOULDBECLEAN,DRYAND

PREFERABLYLUBRICATED.FORBESTRESULTSDRAINTHE
MOISTUREFROMYOUR COMPRESSORDALLY.

Use Only Impact Sockets & Accessories
Only use sockets designated "FOR USE WITH IMPACT
WRENCHES." Hand tool sockets can break, creating a

hazard from flying pieces. Always check sockets,

retainers and drives regularly for wear or damage and

replace when necessary.

FULL ONE YEAR WARRANTY ON
CRAFTSMAN AIR-DRIVE TOOLS
If this Craftsman tool fails to give complete satisfaction

within one year from the date of purchase, RETURN IT
TO THE NEAREST SEARS STORE IN THE UNITED

STATES, and Sears will repair it free of charge. If this
Craftsman tool is used for commercial or rental

purposes, this warranty applies for only 90 days from the
date of purchase. This warranty gives you specific legal
rights, and you may also have other rights which vary

from state to state.

Distributed by Sears, Roebuck and Co., Dept. 817WA,
Hoffman Estates, IL 60179.

The Craftsman Model 875.1998300 1/2" Square Drive

Impact Wrench is ideal for general assembly,

automotive, agricultural and industrial applications.

Features

• Built-in regulator for power output adjustment.

• Pin type clutch for increased power output.

• Ring-type socket retainer allows quick socket
changes.

Specifications

Drive size ............................................................................... 1/2"

Impacts per minute ..................................................... 900 IPM

Free speed (No Load) ........................................... 7,500 RPM

Ultimate torque ....................................................... 400 ft. tbs.

Weight ............................................................................. 5.1Ibs.

Overall length ....................................................................... 7_/8''

Average air consumption ............................................ 6.5 CFM

Recommended hose size ........................................... 3/8" I.D.

Air inlet.......................................................................... 1/4" NPT

Maximum Air Pressure .................................................. 90 PSI

WARNING: Some dust created by using power tools
contains chemicals known to the state of California to

cause cancer and birth defects or other reproductive

harm.

Some examples of these chemicals are:

• Lead from lead based paint

• crystalline silica from bricks and cement
and other masonry products, and

• arsenic and chromium from chemically-

treated lumber.

, WARNING]

Your risk from those exposures varies, depending on

how often you do this type of work. To reduce your

exposure to these chemicals: work in a well ventilated
area, and work with approved safety equipment, such as
dust masks that are specifically designed to filter out

microscopic particles.

Pre-Operation

Before the tool is connected to the air supply, clear the air
hose of accumulated dust and moisture by running air

freely through the air hose for 5-10 seconds. Before

removing a toot for service or changing sockets, make

sure the air line is shut-off at the compressor. This will
prevent the tool from operating if the throttle is accidentty

engaged.

Installation (See figure 1)

This toot is designed to operate at 90 psi. Lower pres-
sure (below 90 psi) will reduce performance of the toot
while higher air pressure (over 90 psi) raises the perfor-

mance of the toot beyond its rated capacity and could

cause serious damage to tool and user.
Always use clean dry air. Excessive moisture and dirt wilt

greatly reduce the life of any air motor. We recommend
the installation of an in-line filter-regulator-lubricator as
close to the toot as possible.

A 3/8" air hose is required up to a length of 8 ft. If more

length is required a 1/2" air hose should be used at the

compressor. Attach a 3/8" whip hose for the remaining
4 - 8 ft. for flexibility. Be sure all hoses and fittings are the

correct size and tightly secured before using air tool.

(2)