Craftsman 875199590 Owner’s Manual

Owner's Manual

Continuous Operation

AIR GREASE GUN

Model No.

875.199590

WARNING:

Before operating tool, read this
manual and follow all

Safety Recommendations and
Operating Instructions.

Safety

, Warranty

Features & Operation
Maintenance

Espahol

Distributed by Sears, Roebuck and Co., Hoffman Estates, IL 60179

www.Sears.com

ReadOperatingInstructions

Please become familiar with all the instructions and
warnings before operating any pneumatic tool.

Always Wear Approved Eye Protection
impact resistant eye protection should meet or exceed
the standards set forth in ANSI Z87.1, Occupational and
Educational Eye and Face Protection. Look for marking
Z87.1 on your eye protection to ensure that it is an
approved style.

Hearing Protection is Recommended
Hearing protection should be used when the noise Ievel
exposure equals or exceeds an 8 hour time-weighted
average sound level of 85dBA. Process noise, reflective

surfaces, other tools being operated nearby, all add to the
noise level in a given work area. Ifyou are unable to
determine your noise level exposure, we recommend the
use of hearing protection.

Avoid Prolonged Exposure to Vibration

Pneumatic tooIs can vibrate during use. Prolonged
exposure to vibration or very repetitive hand and arm

movements can cause injury. Discontinue the use of any
tool if you experience tingling, numbness, discomfort or
pain in your hands or arms. You should consult your

physician before resuming use of tool.
90 PSI Maximum

This tool is designed to operate at an air pressure of 90
pounds per square inch gauge pressure (90 PSi)
maximum, at the tool. Use of higher air pressure can, and
may cause injury. Also, the use of higher air pressure

places the internal components under loads and
stresses they were not designed for, causing premature

tool failure.
NOTE: THE AIR SUPPLY SHOULD BE CLEAN, DRYAND

PREFERABLY LUBRICATED. FOR BEST RESULTS
DRAIN THE MOISTURE FROM YOUR COMPRESSOR
DALLY.

FULL ONE YEAR WARRANTY ON
CRAFTSMAN AIR-DRIVE TOOLS

if this Craftsman tool fails to give complete satisfaction

within one year from the date of purchase, RETURN iT
TOTHE NEAREST SEARS STORE IN THE UNITED

STATES, and Sears will repair it free of charge, if this
Craftsman tool is used for commercial or rental

purposes, this warranty applies for only 90 days from the
date of purchase. This warranty gives you specific legal
rights, and you may also have other rights which vary

from state to state.
Distributed by Sears, Roebuck and Co., Dept. 817WA,

Hoffman Estates, IL 60179.

The Craftsman Model 875.199590 Continuous Flow
Grease Gun is designed for both automotive as well

as heavy industrial usage.
Features

The Craftsman professional Continuous Flow Grease
Gun Model 875.199590 is designed to operate at 60
to 150 PSI. Lower pressure will reduce the
performance of the tool, while pressure higher than
the rated 150 PSl will damage the internal
components to the tool.

• Exclusive air piston design assures self priming.

• Fully automatic; cycles continuous grease flow
when the trigger is depressed.

• Heavy duty spring for prime retention.

• High pressure performance with 60 to 150 PSI
generated at the compressor allows the tool to

deliver 2400 to 6000 PSI (40:1 ratio) of pressure

into the desired fitting.

Some dust created by power sanding, sawing, grinding,
drilling and other construction activities contains chemi-

cals known to cause cancer, birth defects or other
reproductive harm. Some examples of these chemicals

are:

Lead from lead based paint

crystalline silica from bricks and cement
and other masonry products, and

arsenic and chromium from chemically-
treated lumber.

Your risk from those exposures varies, depending on how
often you do this type of work. To reduce your exposure to

these chemicals: work in a well ventilated area, and work
with approved safety equipment, such as dust masks that
are specifically designed to filter out microscopic par-

ticles.

Pre-Operation

Before the tool is connected to the air supply, clear the air

hose of accumulated dust and moisture by running air
freely through the air hose for 5-10 seconds. Before
removing a tool for service or changing sockets, make

sure the air Iine is shut-off at the compressor. This wilI
prevent the tool from operating if the throttle is accidently
engaged.

Installation (See figure 1)

This tool is designed to operate at 90 psi. Lower pres-
sure (below 90 psi) will reduce performance of the tool
while higher air pressure (over 90 psi) raises the perfor-

mance of the tool beyond its rated capacity and could
cause serious damage to tool and user.

Always use clean dry air. Excessive moisture and dirt will
greatly reduce the life of any air motor. We recommend
the installation of an in-line filter-regulator-lubricator as
close to the tool as possible.

A 3/8" air hose is required up to a length of 8 ft. If more
length is required a 1/2" air hose should be used at the

compressor. Attach a 3/8" whip hose for the remaining
4 - 8 ft. for flexibility. Be sure all hoses and fittings are the
correct size and tightly secured before using air tool.

(2)