Craftsman 875199500 Owner’s Manual

Owner's Manual

Pneumatic

3/8" REVERSIBLE DRILL

Model No.

875.199500

WARNING:

Before operating tool, read this manual and follow all

Safety Recommendations and Operating Instructions.

, Safety

Warranty

Features & Operation Maintenance

Espa#ol

Distributed by Sears,

www,,Sears,,com

Roebuck and Co., Hoffman Estates, IL 60'179

Read Operating Instructions

Please become familiar with all the instructions and

warnings before operating any pneumatic tool.

Always Wear Approved Eye Protection Impact resistant eye proteclien should meet or exceed

the standards set forth in ANSI Z87t, Occupational and

Educational Eye and Face Protection Look for marking

Z87..t on your eye protection te ensure that it is an

approved style.. ttearing Protection is Recommended

Hearing protection should be used when the noise level exposure equals or exceeds an 8 hour time-weighted

average sound level of 85dBA Process noise, reflective surfaces, other tools being operated nearby, all add to the

noise level in a given work area. If you are unable to determine your noise level exposure, we recommend the use of hearing protection..

Avoid Prolonged Exposure to Vibration Pneumatic tools can vibrate during use.. Prolonged

exposure to vibration er very repetitive hand and arm movements can cause injury.. Discontinue the use of any

tool if you experience tingling, numbness, discomfort or pain in your hands or arms. You should consult your

physician before resuming use of tool.

90 PSI Maximum

This tool is designed to operate at an air pressure of 90

pounds per square inch gauge pressure (90 PSI)

maximum, at the tool. Use of higher air pressure can, and may cause injury. Also, the use of higher air pressure

places the internal components under loads and stresses they were not designed for, causing premature

tool failure. NOTE: THE AIR SUPPLY SHOULD BE CLEAN, DRYAND

PREFERABLY LUBRICATED. FOR BEST RESULTS DRAIN THE MOISTURE FROM YOUR COMPRESSOR

DALLY

Use Proper Accessories

Always disconnect tool from air supply before changing accessories. Never hold work in hands, lap or against

other paris of the body Secure all work with clamps or a vice so that both hands are free to operate tool. Keep

proper footing and balance at all times.. Verify tool direction before starting. Do not change direction of tool

while tool is running. Do not force tool, allow drill to work at designed pace.

I, WARNINGI

Some dustcreated by power sanding, sawing, grinding,ddlltng

and other construction activities containschem}caIs knownto causecancer,birth defects or other reproductive harm Some

examples ofthese chemicalsare:

Lead fromlead based paint crystalline silica from bricksand cement

and other masonry products, and

arsenicand chromium fromchemically-

treatedlumber.

Your risk from those exposures varies, depending on how often you do thistype of work. To reduce your exposure tothese

chemicals: work ina well ventilated area, and work with approved safety equipment, such as dust masks that are specilieally designed to filler out microscopic particles

FULL ONE YEAR WARRANTY ON

CRAFTSMAN AIR-DRIVETOOLS

If this Craftsman tool fails to give complete satisfaction

within one year from the date of purchase, RETURN IT TO THE NEAREST SEARS STORE IN THE UNITED

STATES, and Sears will repair or replace it free of charge If this Craftsman tool is used for commercial or rental

purposes, this warranty applies for only 90 days from the date of purchase. This warranty gives you specific legal

rights, and you may also have other rights which vary from state to state.

Distributed by Sears, Roebuck and Con, DepL 817WA, Hoffman Estates, IL 60179,

The Craftsman Model 875,. 199500 3!8" Reversible Drill

is designed for applications which include drilling, honing, wire brushing and fastening!unfastening of screws.. This tool features a side mounted reverse

lever for quick and easy direction changes. Features

• Planetary gears for smooth power transfer and low

vibration.

Side mounled reverse lever for quick direction change..

• Jacobs_ chuck for tong life

Specifications

Spindle Thread ...................................................................................................3/8"x 24

Free speed (No Load) ........................................................................2200 RPM

Weight .................................................................................................................................2.1 lbs

Overall length .................................................................................................................6-1/2."

Average air consumption ..................................................................5 5 SCFM

Recommended hose size.....................................................................318"[.D,

Air inlet..........................................................................................................................I14" NPT

Maximum Air Pressure ............................................................................................g0 PSI

Pre-Operation

Beforethetootisconnectedtotheairsupply,cfeartheair

hose of accumulated dust and moisture by running air freely through the air hose for 5-10 seconds. Before removing a tool for service or changing sockets, make sure the air line is shut-off at the compressor This wilt prevent the tool from operating if the throttle is accidently

engaged..

Installation (See figure 1)

This tool is designed to operate at 90 psL Lower pres-

sure (below 90 psi) will reduce performance of the tool

while higher air pressure (over 90 psi) raises the perfor-

mance of the tool beyond its rated capacity and could

cause serious damage to tool and user

Always use clean dry air Excessive moisture and dirt will

greatly reduce the life of any air motor. We recommend

the installation ef an in-line filter-regulator-lubricator as

close to the tool as possible

A 3/8" air hose is required up to a length of 8 ft. If more

length is required a 112" air hose should be used at the compressor. Attach a 3/8" whip hose for the remaining

4 - 8 ft.. for flexibility.. Be sure all hoses and fitlings are the

correct size and tightly secured before using air tool

(2)

More than 1/100 slope

Stop Regulator Valve Lubricator

_AutoDrain _ Valve

Air Hose Hook Up

This 3t8" Reversible Pistol Grip Drill is designed to operate on 90 PSlG. Lower pressure (below 90 PSlG) will

reduce performance of the tool while higher air pressure (over 90 PSlG) raises the performance of the tool beyond

its rated capacity and could cause serious damage to tool and user,

Warning: Disconnect tool from air supply before servicing or changing accessories.

Disconnect air supply prior to changing bits. Drill bits should be inserted as far as possible. Use approximately

sized chuck key to securely tighten ddll bit, lap or reamer in drill chuck.. Always remove chuck key before connecting to air iine,

Caution must be exercised when using any

cutting tool because of the possibility of the cutting tool bending or breaking. Cutting tool

maximum speed rating must equal or exceed rated speed of tool,

Filter

Figure 1

Main line = 3 times

Tool inlet/nose size

Stop Vave

Air Compressor

Lubrication

An in-line filter-regulator-lubricator (fig 1) is recommended as it increases tool life and keeps the tool in sustained

operation,, The in-line lubricator should be regularly checked and filled with air tool oil,, Proper adiuslment of 1hein-line lubricator is performed by placing a sheet of

paper next to the tools exhaust ports and holding the throttle open approximately 30 seconds. The lubricator is

properly set when a light stain of oil collects on the paper Excessive amounts of oil should be avoided,,

In the event that it becomes necessary to store the tool for an extended period of time (ovemight, weekend, etc), it

should receive a generous amount of lubrication through the air inlet.. The tool should be run for approximately 30 seconds to ensure oit has been evenly distributed

throughout the tool.. The tool shou?d be stored in a clean and dry environment.

Recommended lubricants: Use air tool oil or any other high grade turbine oil containing moisture absorbent, rust

inhibitors, metal wetting agents and an EP (extreme pressure) additive..

High reaction torque may be experienced with any drill at break through.

Sears CRAFTSMAN Model 875.199500

Pneumatic 3/8"Reversible Drill

Exploded View and Parts List

7Ref,,

1 2

4 5

t0 tt

t2 13

14 15

15 17

18 19

2O 21

23 24

Part No,

91t3001-0t 913012

976350

9106655

976306 976309

976310 9963t2 976312

976313 9106363

96315-01 9113013

91130t4 91130t5-01

9tl 3016 914517

9113018 9113019

9t 3002 9113021-01

9113025

9145t 5

9t 23020

DescdptJon Q'ty

Housing 1 Tdgger Pin I Muffler Cover t Ceramic Balls 20

Bushing t Valve Seat t

Throttle Valve t Valve Spdng t

Exhaust Deflector t Washer 1 O-Ring 1 Air Inlet Bushing 1

Reverse Bushing 1

Reverse Valve 1 Reverse Lever 1

Spdng 1 Steel Bail 1

Screw 1

Retainer Ring 1

O-Ring 2 Tdgger 1

Gasket 1

Ball Beadng 1 Rear End Plate 1

(4)

Ref,,

25 26

27 28

31 32

33 34

35 36

39 40 41

42 43

44 45

Part Noo

9123021 914519

913021 913022

9123025 9106378

927023

9150140

913026

9113037 9113038

9113036 9113035

9t 06648

9113039

9t 303I 5950

9t 3033 59!4

9113044_01 913007

Description Q'ty

Rotor 1 Rotor Blade 5

Cylinder 1 Set Pin !

Front End Plate 1 Ball Bearing t

Ball Beadng 1 Planet Gear 2 Gear Pin 2

Spindle t Internal Gear t

Spdng Pin ! Ornamental Gasket 1

Bafl Beadng 2 Gear Case 1

Washer 1 Chuck 1

Chuck Screw 1 Chuck Key 1 Houslng Bushing 1

O_Ring 1

+ 7 hidden pages