Craftsman 875167070 Owner’s Manual

Owner's Manual

Pneumatic

SAND BLASTER

Model No.

875.167070

WARNING:

Before operating tool, read this
manual and follow all

Safety Recommendations and
Operating Instructions.

, Safety
, Warranty

, Features &Operation

Maintenance

, Espahol

Distributed by Sears, Roebuck and Co., Hoffman Estates, IL 60179

www.Sears.com

ReadOperatingInstructions

Please become familiar with all the instructions and
warnings before operating any pneumatic tool.

Always Wear Approved Eye Protection
impact resistant eye protection should meet or exceed
the standards set forth in ANSI Z87.1, Occupational and
Educational Eye and Face Protection. Look for marking
Z87.1 on your eye protection to ensure that it is an
approved style.

Hearing Protection is Recommended
Hearing protection should be used when the noise Ievel
exposure equals or exceeds an 8 hour time-weighted
average sound level of 85dBA. Process noise, reflective

surfaces, other tools being operated nearby, all add to the
noise level in a given work area. Ifyou are unable to
determine your noise level exposure, we recommend the
use of hearing protection.

Avoid Prolonged Exposure to Vibration

Pneumatic tooIs can vibrate during use. Prolonged
exposure to vibration or very repetitive hand and arm

movements can cause injury. Discontinue the use of any
tool if you experience tingling, numbness, discomfort or
pain in your hands or arms. You should consult your

physician before resuming use of tool.
90 PSI Maximum

This tool is designed to operate at an air pressure of 125
90 pounds per square inch gauge pressure (125 PSi)
maximum, at the tool. Use of higher air pressure can, and
may cause injury. Also, the use of higher air pressure

places the internal components under loads and
stresses they were not designed for, causing premature

tool failure.
NOTE: THE AIR SUPPLY SHOULD BE CLEAN, DRYAND

PREFERABLY LUBRICATED. FOR BEST RESULTS
DRAIN THE MOISTURE FROM YOUR COMPRESSOR
DALLY.

FULL ONE YEAR WARRANTY ON
CRAFTSMAN AIR-DRIVE TOOLS

if this Craftsman tool fails to give complete satisfaction

within one year from the date of purchase, RETURN iT
TOTHE NEAREST SEARS STORE IN THE UNITED

STATES, and Sears will repair it free of charge, if this
Craftsman tool is used for commercial or rental

purposes, this warranty applies for only 90 days from the
date of purchase. This warranty gives you specific legal
rights, and you may also have other rights which vary

from state to state.
Distributed by Sears, Roebuck and Co., Dept. 817WA,

Hoffman Estates, IL 60179.

The Craftsman Model 875.167070 Sand Blaster is
ideal for removing rusr and paint from a variety of

surfaces.

Features

• Compact Design.

• Maintenance free.

• Complete with three tips.

Specifications

Tip Size ............................................................. 4.8 mm or 3/16"

Weight ........................................................................... 2.42 Ibs.

Sand inlet Pipe Size ........................................... 13ram or 1/2"

Average air consumption ........................................ 9.5 SCFM

Suction Capacity ......................................................... 0.06 MPA

Recommended hose size........................................... 3/8" i.D.

Air inlet.......................................................................... 1/4" NPT

Maximum Air Pressure ................................................. 125 PSi

Some dust created by power sanding, sawing, grinding,
drilling and other construction activities contains chemi-

cals known to cause cancer, birth defects or other
reproductive harm. Some examples of these chemicals

are:

Lead from lead based paint

crystalline silica from bricks and cement
and other masonry products, and

arsenic and chromium from chemically-
treated lumber.

Your risk from those exposures varies, depending on how
often you do this type of work. To reduce your exposure to

these chemicals: work in a well ventilated area, and work
with approved safety equipment, such as dust masks that
are specifically designed to filter out microscopic par-

ticles.

Pre-Operation

Before the tool is connected to the air supply, clear the air

hose of accumulated dust and moisture by running air
freely through the air hose for 5-10 seconds. Before
removing a tool for service, make sure the air line is shut-

off at the compressor. This will prevent the tool from
operating if the throttle is accidently engaged.

Installation (See figure 1)

This tool is designed to operate at 40 - 125 psi. Lower
pressure (below 40 psi) will reduce performance of the
tool while higher air pressure (over 125 psi) raises the

performance of the tool beyond its rated capacity and
could cause serious damage to tool and user.

Always use clean dry air. Excessive moisture and dirt will
greatly reduce the life of any air motor. We recommend
the installation of an in-line filter-regulator-lubricator as
close to the tool as possible.

A 3/8" air hose is required up to a length of 8 ft. If more
length is required a 1/2" air hose should be used at the

compressor. Attach a 3/8" whip hose for the remaining
4 - 8 ft. for flexibility. Be sure all hoses and fittings are the
correct size and tightly secured before using air tool.

(2)