Craftsman 875167061 Owner’s Manual

Owner's Manual

Pneumatic

SANDBLASTE

50 Ibs Capacity

Model No.

875.167061

WAR NING:

Before operating tool, read this manual and follow a II

Safety Recommendations and 0 perating Instructions.

Safety Wa rranty

Features & Operation

Maintenance

Espaffol

Distributed by Sears,

www.Sears.com

Roebuck and

Co_,

Hoffman

E states,

IL 60179

Read Operating Instructions Please become familiar with all the instructions and

warnings before operating any pneumatic tool. Always Wear Approved Eye Protection

Impact resistant eye protection should meet or exceed

the standards set forth in ANSI Z87.1, Occupational and

Educational Eye and Face Protection. Look for marking Z87.1 on your eye protection to ensure that it is an approved style.

Hearing Protection is Recommended

Hearing protection should be used when the noise level exposure equals or exceeds an 8 hour time-weighted average sound level of 85dBA. Process noise, reflective surfaces, other tools being operated nearby, all add to the

noise level in a given work area. If you are unable to determine your noise level exposure, we recommend the

use of hearing protection. Avoid Prolonged Expos ure to Vibration

Pneumatic tools can vibrate during use. Prolonged exposure to vibration or very repetitive hand and arm

movements can cause injury. Discontinue the use of any tool if you experience tingling, numbness, discomfort or

pain in your hands or arms. You should consult your

physician before resuming use of tool. 90PSI Maximum

This tool is designed to operate at an air pressure of 90

pounds per square inch gauge pressure (90 PSI)

maximum, at the tool. Use of higher air pressure can, and

may cause injury. Also, the use of higher air pressure

places the internal components under loads and stresses they were not designed for, causing premature

tool failure.

NOTE: THE AIR SUPPLY SHOULD BE CLEAN, DRYAND

PREFERABLY LUBRICATED. FOR BEST RESULTS

DRAINTHE MOISTURE FROMYOUR COMPRESSOR

DAILY.

FULL ONE YEAR WARRANTY ON CRAFTSMAN AIR-DRIVE TOOLS

If this Craftsman tool fails to give complete satisfaction within one year from the date of purchase, RETUR N IT

TOTHE NEARESTSEARS STORE INTHE UNITED

STATES, and Sears will repair it free of charge. If this Craftsman tool is used for commercial or rental

purposes, this warranty applies for only 90 days from the date of purchase. This warranty gives you specific legal

rights, and you may also have other rights which vary from state to state.

Distributed by Sears, Roebuck and Co., Dept. 817WA, Hoffman Estates, IL 60179.

The Craftsman Model 875.167061 Sand Blaster is

ideal for removing rustand paint from a variety of

surfaces.

Features

• Compact Design.

• Maintenace free.

• Complete with three tips.

Specifications

Tip Size ............................................................. 4.8 mm or 3/16"

Weight. .......................................................................... 2.42 Ibs.

Sand Inlet Pipe Size ........................................... 13mm or 1/2"

Average air consumption ........................................ 9.5 SCFM

Suction Capacity. ........................................................ 0.06 MPA

Recommended hose size ........................................... 3/8" I.D.

Air inlet ......................................................................... 1/4" NPT

Maximum Air Press ure .................................................. 90 PSI

[ WARNIN ]

Some dust created by power sanding, sawing, grinding, drilling and other construction activities contains chemi-

cals known to cause cancer, birth defects or other

reproductive harm. Some examples of these chemicals are:

Lead from lead based paint

crystalline silica from bricks and cement and other masonry products, and arsenic and chromium from chemically-

treated lumber.

Your risk from those exposures varies, depending on how often you do this type of work. To reduce your exposure to

these chemicals: work in a well ventilated area, and work with approved safety equipment, such as dust masks that

are specifically designed to filter out microscopic par- ticles.

P re-Operation

Before the tool is connected to the air supply, clear the air hose of accumulated dust and moisture by running air

freely through the air hose for 5-10 seconds. Before

removing a tool for service, make sure the air line is shut-

off at the compressor. This will prevent the tool from operating if the throttle is accidently engaged.

Installation (See figure 1)

This tool is designed to operate at 90 psi. Lower pres- sure (below 90 psi) will reduce performance of the tool

while higher air pressure (over 90 psi) raises the perfor-

mance of the tool beyond its rated capacity and could

cause serious damage to tool and user. Always use clean dry air. Excessive moisture and dirt will

greatly reduce the life of any air motor. We recommend the installation of an in-line filter-regulator-lubricator as

close to the tool as possible.

A 3/8" air hose is required up to a length of 8 ft. If more

length is required a 1/2" air hose should be used at the compressor. Attach a 3/8" whip hose for the remaining 4 - 8 ft. for flexibility. Be sure all hoses and fittings are the correct size and tightly secured before using air tool.

(2)

i_ M4orethanl/100slope

Branch line = 2 times I Stop Filter am. me = lmes _-4

Tool inlet/hose size / Valve Regulator Tool inlet/hose size

I _ _ Stop _ /

Auto Drain _ _ ValveW_::::_

w,ve II

bAuto Drain _ ( Air C ......... _1

Valve Air HFigHrelk Up

Always wear head and face protection, long sleeve, jacket pants, work shoes and rubber gloves. Wear a respirator.

Air Tool _-,.I

Protect other people. Allow no one in the blasting area

unless they are wearing safety equipment.

Sand hitting metal can cause a spark., NEVER work near

oily rags, gas tanks or flammable liquids.

Never point the sand blast stream at any person or part of

the body. Always depressurize and disconnect incoming air hose when sandblaster is unattended.

Check and tighten sand hose clamps and check other

fittings for leaks and wear. Watch for loose or worn hose

and fittings and replace as needed.

Prior to adding abrasive, fully pressurize the unit to check all hose and pipe fitting for tightness. Check the operation

of all valves and other components. Check for air leaks

and tighten as necessary. Turn the sandblaster on and off several times to become familiar with the operation.

[ WARN|N I

Only after reading the safety instructions and testing the

unit without sand, you may then add sand and start to

sandblast

Sears CRAFTSMAN SAND BLASTER

Exploded View and

Model 875.167061

Parts List

Ref,

2 3

4 5

6 7

8 9

10 10 10

Part No.

9106731 9106732

9106733 9106734

9106735 9106736 9106737

9106738 9106739

9106740A 9106740B 9106740C

21 (

Description Housing

Washer Valve Stem

Spring

O-R ing

Screw

O-Ring

Screw

Washer

Nozzle (1/8") Nozzle (3/32")

Nozzle (5/64")

15 14

iii

Q 'ty

10 11

Ref.

1 1

1 1 1

1 1

1 1 1

11 12

13 14

15 16

17 18

19 20

21 Not Shown

Part No. 9106741 9106742

9106743 9106744

9106745 9106746

9106747 9106748

9106749 9106750

9106752

9106753

9106754

9106755

9106756

, _) i

Description O-Ring Nozzle Body Screw Washer

C ermaics Nozzle Iron S lice

Connect Head Trigger

Spring P in Hex Key

Hose

Screen Hopper

Lock Washer Nut

Q 'ty

2 1

1 1

(4)

+ 7 hidden pages