Craftsman 79653, 24079653 Owner’s Manual

Instruction Manual for Electric Edger

EZ.Edge.n.Store

Model No. 71.79653

BEFORE RETURNING THIS PRODUCT FOR ANY REASON PLEASE FIRST CALL

(800) 539-6455

IN MOST CASES A CRAFTSMAN REPRESENATIVE WILL BE ABLE TO HELP YOU SOLVE YOUR ISSUE OVER THE PHONE.

iMPORTANT OPERATING HINTS:

• When starting unit, first push in the

safety switch and then squeeze the main trigger. It is NOT necessary to keep the safety switch pushed in

during use.

• Stay to the left and behind the edger when in use. The edger will push

clippings and other debris forward,

away from the user.

• This is a powerful cutting tool. Be AWARE of your surroundings.

CAUTION: Before using this product, read this manual and follow

all its Safety Rules and Operating Instructions.

Sears, Roebuck and Co., Hoffman Estates, IL 60179 U.S.A.

www.sears.com/craftsman

WARNING: Some dust created by using power tools contains chemicals

known to the state of California to cause cancer and birth defects or other reproductive harm.

Warranty ..................................................................................................... 3

Safety Instructions ..................................................................................... 3

Assembly .................................................................................................... 6

Operation ................................................................................................... 7

Maintenance ............................................................................................... 9

Storage ....................................................................................................... 9

Service ....................................................................................................... 9

Troubleshooting .......................................................................................... 9

Espa_ol ..................................................................................................... 11

Fran£;ais .................................................................................................... 21

Full One Year Warranty on Craftsman Products

Ifthis Craftsman product fails due to a defect in material or workmanship within one year from the date of purchase, return it to your nearest Sears store or Craftsman outlet in the United States, and it wilt be replaced free of

charge. This warranty applies only while this product is used in the United States.

This warranty gives you specific legal rights, and you may also have other rights, which vary from state to state.

Sears, Roebuck and Co., Dept. 817WA, Hoffman Estates, IL 60179

READ ALL INSTRUCTIONS

BEFORE OPERATING TOOL

A " •

WARNING TO CALIFORNIA RESIDENTS: Handling the cord on

this units (or cords with accessories sold for this product) will expose you to lead, a chemical known to the State

of California to cause cancer, and birth defects or other reproductive harm. Please wash hands after handling the

cord.

WARNING: Certain dusts created when using lawn and graden

power tools contain chemicals that are known to cause cancer, birth defects, or other reproductive harm. Examples of these chemicals

are: compounds in fertilizers,

compounds in insecticides, herbicides, and pesticides, arsenic and chromium from chemically treated wood products and crystalline silica from sand, bricks,

and other masonry dust.

The health risk from these chemicals varies based on working environment

and frequency and length of exposure. To limit exposure to these chemicals, please follow product instructions when applying or working with

fertilizers, insecticides, herbicides, and pesticides. When using the edger, always wear safety glasses and gloves and dust masks that are designed to filter out microscopic materials.

SAVE THIS MANUAL FOR FUTURE

REFERENCE

WARNING: When using this tool, basic safety precautions should always be followed to reduce the risk of fire, electric shock, and personal injury, including the following:

To reduce risk of injury: * Before any use, be sure everyone

using this electric product reads and understands all safety and operation instructions contained in

this manual.

* Save these instructions and review

frequently prior to use.

* AVOID DANGEROUS

ENVIRONMENTS and weather conditions when using this tool.

* DO NOT USE IN RAIN. * KEEP CHILDREN AWAY-All

visitors should be kept at a safe distance from work area.

" STORE IDLE UNIT INDOORS -

When not in use, the unit should be stored indoors in a dry location - out

of reach of children.

* DON'T FORCE THE TOOL - It

will do the job better and with tess likelihood of a risk of injury at the

rate for which it was designed.

* USE RIGHT TOOL - Do not use the

tool for any job except that for which it is intended.

round-jacketed extension cords approved for outdoor use.

* To reduce risk of electric shock, this

unit has a polarized plug (one blade is wider than the other). This unit will fit with a polarized plug only one way. If the extension cord plug will

not completely fit on the units plug, reverse the plug. If the extension cord will still not fit, use an extension cord with the proper polarized connection. If the plug still does not

fit, contact a qualified electrician to install the proper wall outlet. Do not alter the unit's plug or extension cord in any way.

* A nameplate on the unit will indicate

the voltage used. This information is needed to determine the wire size

(AWG) of the extension cord you should use. Never connect the unit

to an AC voltage that differs from this voltage.

* WARNING: To reduce the risk of

electric shock, use the unit only with an extension cord intended

for outdoor use, such as SW- A, STW-A, STOW-A, SJW-A, SJOW-A, SJTW-A, or SJTOW-A cord types.

MINIMUM WIRE SIZE FOR

EXTENSION CORDS FOR 120 VOLT

APPLIANCES USING 0-12 AMPS

ELECTRICAL SAFETY WARNINGS AND iNFORMATiON = When servicing, use only identical

replacement parts.

* This tool is double-insulated - repair

or replace damaged cords.

* Since this tool is double-insulated,

a two wire extension cord (an extension cord without a ground) may be used. A three-wire extension cord (an extension cord

with a ground) that uses a NEMA type connector (parallel blade, U ground) is recommended. Use only

Cord length 25 50 100 150 *Wire Size(AWG) 16 16 14 12

*The wire size (AWG) for 120-Volt appliances using 12-16 amps is 14

AWG for 25 feet, 12 AWG for 50 feet, and NOT RECOMMENDED for 100 or

150 feet.

GROUND FAULT CIRCUIT INTERRUPTER (GFCI)

PROTECTION should be provided on the circuits(s) or outlet(s) to be

used for the edger. Use receptacles

with built-in GFCI protection for an

extra measure of safety.

* CORD SETS: Make sure the cord

on the unit and the extension cord are in good condition. The

extension cord should be heavy enough to carry the current the unit

will draw. An undersized cord wilt cause a drop in line voltage that

will cause the unit to loose power and overheat. The above table

shows the correct extension cord sized based on the cord length and

nameplate ampere rating. If you are not sure what cord size to use, use the next heavier size line gauge. The smaller the gauge number, the

heavier the cord.

* DO NOT ABUSE THE CORD-

Never carry the unit by its cord or pull on it to disconnect it from the receptacle. Keep the cord away from heat, oil, and sharp edges and

corners.

* ROUTINELY INSPECT CORDS =

Routinely inspect the units cord as well as the extension cord used.

Look for cuts, nicks, or cracks in the cords insulation. Also inspect the connections to see if they are bent or broken. Repair or replace cords if any defects appear.

OPERATIONAL SAFETY WARNINGS * CLEAR WORK AREA: Use of this

edger may cause debris such as stones, dirt, wood, or metal to be

propelled at a high rate of speed. Be sure work area is clear of other

persons and pets when using the edger.

* STAY CLEAR OF BLADE: Always

stand to the left of the unit when using to avoid being hit by debris

from the blade.

. CHECK FOR BURIED CABLES

BEFORE USE: Before edging or trenching with this product, be

sure to inspect area for any buried electrical or other cables.

* AVOID HITTING CURBS, TREES,

WALLS, ROCKS, SIDEWALKS AND OTHER SOLID OBJECTS

WITH EDGER WHILE USING.

* DANGER: KEEP HANDS, FEET

AND ALL BODY PARTS AWAY from the blade.

* CAUTION: Blade coasts after the

unit is turned off. Unplug unit and wait for blade to come to a complete stop before placing hands or feet

near the blade.

* DRESS PROPERLY- Do not wear

loose clothing or jewelry. They can be caught in moving parts. Use of rubber gloves and substantial

footwear is recommended when working outdoors. Wear protective

hair covering to contain long hair. Wear long pants to shield legs when using edger.

= DON'T OVERREACH - Maintain

proper footing and balance at all times. Use both hands to operate unit safely.

* USE SAFETY GLASSES - Always

wear proper eye protection and use a face or dust mask.

* MAINTAIN UNIT WITH CARE

- Keep the unit clean for best performance and to reduce the risk of injury. Follow instructions for

service. Keep handles dry, clean, and free from oit and grease.

* UNINTENTIONAL STARTING-

Don't hold the switch area while carrying the unit while it is plugged

in. This may cause it to start inadvertently if not handled properly.

Be sure the switch is in the off position when plugging in the unit.

= CHECK DAMAGED PARTS - If

the unit experiences a hard impact, check that no parts were damaged and verify that the unit operates properly. Check for misalignment or bending of moving parts,

breakage of parts, and any other condition that may affect operation. A part that is damaged should be

properlyrepairedorreplacedbyan authorizedservicecenter.

* STAYALERT- Payattentionto

whatyouaredoingandtheposition oftheunit'sblade.Usecommon

sense.Donotoperatethetoolwhen youaretired.

" DON'T GRASP THE EXPOSED

EDGING BLADE when picking up or holding the unit. Do not attempt

to remove dirt or debris when the blade is moving. Make sure the

unit's switch is off when clearing

jammed material from blade area.

* USE BOTH HANDS TO OPERATE

THE UNIT. Keep one hand on the trigger handle and the other on the

front accessory handle. NEVER use the unit's guard as a handle.

" STOP THE MOTOR WHEN THE

UNIT BECOMES ENTANGLED WITH A FOREIGN OBJECT.

Inspect for damage. Do not operate

with loose or damaged parts.

* UNPLUG UNIT =while cleaning

debris and during other maintenance or repair.

• KEEP INSTRUCTIONS AND REFER TO THEM OFTEN. If you

loan this tool to someone please also loan them these instructions so

they may safely understand how to use this unit.

* DISCONNECT APPLIANCE =

Disconnect the appliance from the power supply when not in use, before servicing, when changing

accessories such as blades, and the like.

• KEEP GUARDS in place and in working order.

* KEEP BLADES SHARP. * KEEP HANDS AND FEET away

from cuttinga_a.

SAVE THESE

INSTRUCTIONS

A t,

1. Remove the Edger and all its parts from the packaging.

NOTE: The shaft of the edger MUST

be extended before attempting to assemble the shaft to the motor

housing. This wilt draw the excess wire up into the shaft and wilt allow

the shaft to be fully inserted into the motor housing.

2. Chromed Shaft Extension = Pull

the smaller diameter shaft out to extend the shaft to full-length.

See Figure 1. The cord will feed through the smaller shaft. Secure

the shaft in ONE of THREE height settings with a screw and

"handle"-nut.

Fij.ig.ure-2

Shaft-to-Edger Connection =

Insert the end of the shaft into

the socket in the shaft housing. See Figure 2. Twist the shaft back

and forth while pushing firmly until the shaft is fully seated and

the spring in the shaft are firmly seated into shaft housing. Do not

attempt to insert shaft into shaft housing without fully extending and securing shaft as outlined in

#1 above.

Front Handle Assembly = Line up front handle as shown in Figure 3, then push handle onto upper assembly so the holes line up.

Secure the shaft with the screw and plastic knob.

ATTACHING EXTENSION CORD You can securely fasten the extension

cord by tying it in a knot with the pigtail cord as shown in Figure 4.

depths and 1 transportation mode. To adjust the depth of the cut, move

the front adjustment lever up or down to the desired depth setting. Cutting depths are 518", 1" and 1 1/2". (see depth indicator label).

TRANSPORT MODE

The edger can be raised for transportation and storage. To adjust to transport mode, lower the lever to the bottom "Roll" position. The "Roll"

position raises the edge guide so that it does not hit the ground while transporting.

EDGE GUIDE The EZ-Edge-n-Store is equipped with

a fixed edge guide that makes it easy to follow a sidewalk or curb.

CAUTION - Make sure the edger blade wilt only contact dirt before

turning on.

Fj_ure-4

EDGING DEPTH DANGER - Never attempt to

adjust the depth while the edger is running.

The EZ-Edge-n-Store can be adjusted to edge at different depths - 3 edging

REMOVING THE BLADE COVER The blade cover can be easily

removed to clean out dirt and debris. Depress the button on the top of the

blade cover and lift up to remove the blade cover. To re-attach the blade

cover, simply line up blade cover over the blade guard and press down

until the button locks in place. For your safety the edger will not operate unless the guard is locked securely in place. See Figure 5.

TURNING THE EZ=Edge=n=Store ON

Once the unit is plugged in and you are ready to start edging, simply push

the unit's safety trigger in with your thumb while pulling up on the trigger (under the handle) with your fingers. See Figure 6. The thumb safety

switch is only for starting the unit and can be released during edging. To turn off the unit, release the trigger and the safety switch wilt snap out to prevent the trigger switch from being

accidentally depressed.

adjustedtoanuprightstorageposition byliftinguptheredlockatthebase

oftheshaftandmovingtheshaft forward,intotheuprightposition.The redlockringwillsnapfirmlyintoplace intheuprightposition.SeeFigure7.

Fi=_ure-7

EDGING INSTRUCTIONS AND TECHNIQUES

* Always keep the extension-cord

away from the area being edged. Make sure the extension cord

is behind the edger. If you cut or damage the cord, unplug it

immediately. AFTER the cord is unplugged, inspect it for damage and repair or replace it if necessary.

* Maintain proper balance at all

times. Keep hands away from blades. Wear eye protection when using the unit. Hold the trimmer firmly with both hands and turn

ON.

* Do not use the edger with wet

growth or in the rain.

STORAGE POSITION The Edge-n-Store Edger shaft can be

CAUTION: If the edger becomes

jammed or stalled on a branch, sticks,

or foreign object, release the trigger immediately. Failure to stop the unit when the unit jams may cause excessive damage to the unit's motor.

Clearing Jams After the blade has completely

stopped, carefully remove the obstruction

CAUTION: To prevent injury, keep hands away from trigger during

clearing of jams. To prevent injury, do not use the EZ-Edge-n-Store with any damaged parts. If issues

continue, call the customer service at: 1-800-539-6455

REMEMBER THAT THE BLADE

COASTS AFTER THE UNIT IS

TURNED OFF!

tightening in a clockwise direction.

CLEANING OF PLASTIC PARTS

- Use only a dry brush or a cloth

with warm water and mild soap to clean plastic parts. Many household

cleaners contain chemicals, which could damage the plastic. Never use gasoline, turpentine, paint thinner or similar fluids. Never spray-wash tool or immerse in water. Water or liquid

inside the tool can cause serious damage to the unit.

DROPPING THE UNIT - If you drop the unit, carefully inspect it for any damage before using it again.

A A

CAUTION: To prevent injury, always unplug the edger before performing maintenance such as cleaning or changing the blade.

BLADE CLEANING =After you have finished edging, you may find that dirt and vegetation have accumulated on the blade. Remove the blade guard and use a dry scrub brush to clean

debris off of blades. WARNING: To prevent injury, keep hands away from

the trigger during cleaning of blade or other edger parts.

BLADE CHANGE/TURN = The EZ- Edge-n-Store comes with a DOUBLE-

SIDED BLADE that can be flipped over to effectively double the life of the blade. To change or flip the blade,

remove the blade guard and use the large wrench (included) to hold the blade retainer while loosing the lock nut with the smaller wrench (included) by turning counter-clockwise. Either

change or flip the blade, put the blade retainer in place on the shaft and secure in place with the lock nut by

• = A

PREVENTING CORROSION - Fertilizers and other garden chemicals

contain compounds that greatly accelerate the corrosion of metals.

Do not store the unit on or adjacent to fertilizers or chemicals.

Keep the unit stored in a place that is away from children. The blades on the unit are sharp and can be dangerous even when the unit is not plugged in.

If you see any condition that may affect safe operation, or if you have

any questions, contact our customer service number at: 1-800-539-6455.

"0 ; O®

Problem: Thumb safety switch is

too difficult to hold on during use. Solution: The thumb safety switch

need only be engaged when starting the unit.

Problem: Unit will not operate.

Solution: Make sure that all of the connections are properly made

between the unit, the extension cord, and the recepacle. Ifthe recepacle has Ground Fault Circuit Interrupter (GFCl) protection, make sure that it is working properly and is in the "on"

position. Insure the blade guard is firmly seated in place.

Problem: Motor seems to be running slow

Solution: You may need to use a heavier gauge (AWG) extension cord.

Please refer to the information on Page 3 of this manual concerning

proper extension cord wire size.

NEED MORE HELP?

*i%)u'llfind the answer and a more on managemyhomeocom - for free!

:: • Find this and at[ your other product manua[s online.

, Get answers from our team of home experts.

+ 22 hidden pages