Craftsman 706825520, 706825540-2010, 706825540, 706825470 Owner’s Manual

706.825470

706.825520

I€RAFTSM RN°I

706.825540

Operator's Manual

BALL BEARING SERIES

Please indicate the following information from the service
part drawing provided.

Model Number:

Model Description:

*Product you purchased may vary from picture shown*

CAUTION:

Read and follow all Safety Rules and Operating Instructions before first use
of this product. Retain this document for future reference.

SAFETY WARNINGS AND CAUTIONS:

• DO NOT stand on this product. You may fall which may cause personal injury.

• WEAR SAFETY GLASSES AND GLOVES when cutting the banding material. The
bands may snap which may cause personal injury.

° WEAR SAFETY GLASSES when removing or repositioning the slides. The tool

could slip which may cause personal injury.

• When moving this product, do not pull it. Push the product to prevent personal
injury.

• Handle and swivel casters must be attached on the same side of the product.

• USE THE BRAKES when not moving this product. This will prevent the product
from rolling, which may cause personal injury or product damage.

° BE CAREFUL when opening more than one drawer. The product may become

unstable and tip, which may cause personal injury or product damage.

• DO NOT step in the drawers. You may fall which may cause personal injury.

• Appropriately secure this product before moving it with a forklift.

° DO NOT tow with power equipment. The product could tip, which may cause

personal injury or product damage.

• DO NOT alter this product in any manner. For example, do not weld external
Iockbars or attach electrical equipment. This may cause product damage or
personal injury.

• Keep the product on level surfaces. The product may become unstable and tip if
stored or moved on an un-level surface, which may cause personal injury or
product damage.

• Lock the drawers and doors before moving this product. The drawers or doors
could come open and make the product unstable and tip, which may cause
personal injury or product damage.

• When the cover is opened, be sure the cover stop is in the locked position. This will
prevent accidental closure and personal injury.

• BE CAREFUL when closing the cover. Remove hands before the cover closes
completely to prevent personal injury.

• The maximum weight for each drawer should be no more than 50 pounds.

• The maximum product weight, including contents, should be no more than 1000
pounds for RolI-Aways.

• Close the cover and lock the drawers and doors before moving this product. The
drawers or doors could come open and make the product unstable and tip, which

may cause personal injury or product damage.

• Remove the work surface, if provided, from the cart before mounting the chest.
Failure to do so may cause the chest to slide off, which may cause personal injury
or product damage.

• When locking a chest, close the drawers before closing the cover for lock bars to
work properly.

Sears, Roebuck and Co., Hoffman Estates, IL 60179 USA

F1492 2

Call 1-800-4MY-HOME (1-800-469-4663) for Service Parts
Refer to Service Parts Drawing for full listingof Service Parts

HARDWARE:

(4) 14-10X 3/4 Screw

J

(16) 1/4-20X 5/8 Screw

REMOVING AND INSTALLING SLIDES:
NOTE: To remove the slide from the

unit, first remove the drawer.

• Lift and hold the spring retainer, and
push the slide toward the rear of the
unit. The slide may now be removed.

1/4"Nut

(16) 1/4" Nut

SIDE HANDLE ATTACHMENT:

• Attach the side handle using (4) 14-10 x
3/4 screws. Do not over tighten screws.

CASTER INSTALLATION:
NOTE: Use adequate manpower for this

operation.

• Remove the bottom drawer byfollowing
the drawer removal instructions.

• Lay the cabinet down on itsback. Use
packaging material to protect the paint

finish.

• Mount both swivel casters on the same
side of the cart.

• Attach each caster using (4) 1/4-20 x 5/8
screws and (4) 1/4" nuts per caster.

• Wrench tighten all screws.

• Return the cart to its upright position.

REMOVING AND INSTALLING

DRAWERS:

• Empty the drawer.

• Fully extend the drawer.

Release

J_ Release

Right

• Lever Style - Lift or lower (depending

on the slide) the release lever on both
sides, (this allows the slides to ride
over the stops). Pull out to remove.
Tab Style - Depress the release tabs

on both sides, (this allows the slides
to ride over the stops). Pull out to

remove.

• To reinstall, push the drawer into the

unit until the drawer stops.

/

\\\\\\

//

Spring

Retainer

To reinstall the slide, place the slide in
the appropriate position in the unit and

pull toward the front of the unit until the

spring retainer snaps into position and
secures the slide.

• For casters, use high quality bearing
grease, (yearly).

• Lubricate the slides, (twice yearly).

• Lubricate Iockwith graphite, (yearly).

• Periodically the drawer fronts, drawer
trim, and other surfaces should be
cleaned with a mild detergent and

water.

• Auto wax will preserve the storage

unit's luster finish. Apply the wax as to

a car. The wax will also help protect the

unit against scratches.

• Grease and oil can be removed with

most standard cleaning fluids. For

safety, use a nonflammable cleaning
fluid.

• If drawer liners are supplied, it is

recommended they are used to protect

the finish inside the drawers and to

make the drawers easier to clean. The

drawer liners may be cleaned with
soap and water.

3 4