Craftsman 70670970 Owner’s Manual

Operator's Manual

Please indicate the following information from the service part drawing provided.

SAFETY WARNINGS AND CAUTIONS:

• DO NOT stand on this product. You may fall which may cause personal injury.

•WEAR SAFETY GLASSES when removing or repositioning the slides. The tool could
slip which may cause personal injury.

•When moving this product, do not pull it. Push the product to prevent personal injury.

•Stacked products should be bolted together. The products could become unstable and

tip, which may cause personal injury or product damage.

• Handle and swivel casters must be attached on the same side of the product.

• USE THE BRAKES when not moving this product. This will prevent the product from

rolling, which may cause personal injury or product damage.

• BE CAREFUL when opening more than one drawer. The product may become un
stable and tip, which may cause personal injury or product damage.

• DO NOT mount this product on a truck bed or any other moving object. This may cause
personal injury or product damage.

• DO NOT step in the drawers. You may fall which may cause personal injury.

•Appropriately secure this product before moving it with a forklift.

• DO NOT tow with power equipment. The product could tip, which may cause personal

injury or product damage.

• DO NOT alter this product in any manner. For example, do not weld external Iockbars or
attach electrical equipment. This may cause product damage or personal injury.

• Keep the product on level surfaces. The product may become unstable and tip if stored
or moved on an un-level surface, which may cause personal injury or product damage.

•When rearranging the drawers, be careful not to put too many heavy items in the top
drawers. The product could become top heavy and tip, which may cause personal injury
or product damage.

• BE CAREFUL when closing the cover. Remove hands before the cover closes
completely to prevent personal injury.

• Close the cover and lock the drawers and doors before moving this product. The
drawers or doors could come open and make the product unstable and tip, which may
cause personal injury or product damage.

•When locking this product, close the drawers before closing the cover for lock bars to
work properly.

•The maximum weight for each drawer should be no more than 25 pounds.

•The maximum product weight, including contents, should be no more than 300 pounds

for tool centers.

Model Number:

Model Description:

*Your model may vary from the one shown.

CAUTION: Read and follow all Safety Rules and Operating Instructions before first use
of this product. Retain this document for future reference.

Distributed bySears Brands Management Corporation, Hoffman Estates, IL 60179 USA

F890A13

Call 1=800=4MY=HOME (1-800=469=4663) for Service Parts.
Referto Service Parts Drawingfor full listing of Service Parts.

HARDWARE:

B Q 1/4-20 Hex Nut

O _ 1/4-20 x 7/16 Hex Screw

_) [}_ 8-32 x 1/4 Pan Head Screw

_] @ 8-32 Hex Nut

O _ 10-16x1/2&1/4-14x5/8

Sheet Metal Screw

NOTE: Not all instructions apply
to your specific unit.

REMOVE CHEST FROM ROLL=
AWAY:

• The unit comes with the chest secured
to the inside of the roll-away by either

two or four 1/4-14 x 5/8 screws.

• Lay the roll-away down on its back.

• Use packaging material to protect the

paint finish.

• Remove the securing screws from the

underside of the roll-away. Save the

screws for mounting the chest to the

roll-away.

• Remove the chest.

• Attach casters using 1/4-20 x 7/16

hex screws and 1/4-20 hex nuts.

Wrench tighten.

• Return the roll-awayto its upright
position.

MOUNTING iNTERMEDiATE
CHEST:

• Remove all drawers necessary in

order to attach units. Followthe
drawer removal and installation

instructions in the operation section.

• Position the intermediate chest on the

cabinet. Using the intermediate chest

bottom as a template, mark the
mounting hole locations onto the

roll-away top. At each mark drill a
5/16" diameter hole.

• Attach the cabinet to the intermediate

chest using the bolts supplied with the

units.

• Attach the top chest to the
intermediate chest using the bolts

supplied with the units.

• Reinstall all drawers. Follow the

drawer removal and installation

instructions in the operation section.

MOUNTING CHEST:

• Remove the drawer from the roll-away
(refer to the drawer removal

instructions).

• Lift the chest onto the roll-away. Line
up the holes in the bottom of the chest
with the holes in the top of the

roll-away.

• Attach the chest using two 1/4-14 x
5/8 screws that were used to secure

the chest to the bottom of the roll-
away.

• Wrench tighten all screws.

• Replace the drawer (refer to the

drawer installation instructions).

• To remove the chest, reverse the
procedure.

Chest

Side

Cart

CASTER iNSTALLATiON:

NOTE: Use adequate manpower for
this operation.

• Laythe roll-away down on its back.

• Use packaging material to protect the

paint finish.

• Mount both swivel casters on the
same side of the roll-away. The swivel
caster with the brake goes to the front

of the unit.

RISER ASSEMBLY:

NOTE: When assembled, the riser should
be the same size, left to right, as the
chest. Use adequate manpower for this
operation.

• Assemble the sides and the back (flange
side up) together using four 8-32 x I/4
pan head screws and four 8-32 hex nuts.

Finger tighten.

• Position the riser assembly on the roll-
away. Secure using four 10-16 x I/2

sheet metal screws. Wrench tighten.

• Position the chest on the riser. Secure
using four 10-16 x 1/2 sheet metal

screws. Wrench tighten.

• Wrench tighten the risers four 8-32 x

1/4 pan head screws and 8-32 hex nuts.

3 4