Craftsman 706653881, 706653931, 706654911, 706654910, 706654903 Owner’s Manual

F901

CRAFTSMAN °

PROJECT CENTER

THIS OPERATING INSTRUCTION MANUAL
COVERS ALL PROJECT CENTERS.

Operator's Manual

SAFETY RULES AND WARNINGS:

• DO NOT stand on this product. You may fail which may cause personal injury.

• WEAR SAFETY GLASSES AND GLOVES when cutting the banding material. The
bands may snap which may cause personal injury.

• WEAR SAFETY GLASSES when removing or repositioning the slides. The tool
could slip which may cause personal injury.

• When moving this product, do not pull it. Push the product to prevent personal injury.

• USE THE BRAKES when not moving this product. This will prevent the product from
rolling, which may cause personal injury or product damage.

• BE CAREFUL when opening more than one drawer. The product may become
unstable and tip, which may cause personal injury or product damage.

• DO NOT mount this product on a truck bed or any other moving object. This may
cause personal injury or product damage.

• DO NOT step in the drawers. You may fall which may cause personal injury.

• Appropriately secure this product before moving it with a forklift.

• DO NOT tow with power equipment. The product could tip, which may cause
personal injury or product damage.

• DO NOT alter this product in any manner. For example, do not weld external Iockbars
or attach electrical equipment. This may cause product damage or personal injury.

• Keep the product on level surfaces. The product may become unstable and tip if
stored or moved on an un-IeveI surface, which may cause personal injury or product

damage.

• Lock the drawers before moving this product. The drawers could come open and
make the product unstable and tip, which may cause personal injury or product

damage.

• The maximum weight for each drawer should be no more than 35 pounds.

• The maximum product weight, including contents, cannot exceed 400 pounds.

Please indicate the following
information from the service

part drawing provided.

Model Number:

Model Description:

CAUTION:

Read and follow all

Safety Rules and Operating Instructions before
first use of this product. Retain this document for future reference.

Sears, Roebuck and Co., Hoffman Estates, IL 60179 USA

Made in the U.S.A.

F901A3

A

Call 1-800-366-7278 for Service Parts E JNJ II

Refer to Service Parts Drawing for full listing of Service Parts

CASTER INSTALLATION:

NOTE: It is recommended to use
adequate manpower for this

operation.

• Remove the bottom drawer (if
necessary) by following the drawer
removal instructions.

• Lay the project center on its back,
use packaging material to protect the

paint finish.

• Position the plastic bumpers on the
bottom of the unit.

• Attach the two rigid casters to one end
of the project center using hex head

screws and lock nuts provided.
Wrench tighten.

• Attach the swivel casters at the other
end of the unit in the same manner.

• Return the project center to its upright
position.

]1

U

_LockNut

\Bumper

/

Hex Head Screw .......

DRAWER REMOVAL:

• Fully extend the drawer. Push it back
a quarter of an inch.

• Insert a screwdriver into the slot in the
slide and push in on the stop until it
clears the lance. Repeat the procedure

on the other slide and remove the
drawer.

Slot

Lubricate _

To reinstall the drawer, pry the stop far
enough out to engage the lance (3/16"

to 1/4") and push the drawer onto the
slides until the stops pass over the

lances.

LOCK BAR:
NOTE: The locking bar is stored in

the slot in the back corner of the
plastic top.

• To lock the drawers, insert the top end
of the Iockbar through the slot in the

top of the unit and over the staple on
the base.

• To secure, lock with a padlock
(padlock not included).

• To unlock the drawers, reverse this
procedure.

j-- Stop

Lance

LockbarSlot_X

/

/

Lockbar /

PANEL:

• To open: Pull the panel out, lift it up
and push it back into the unit.

• To close: Reverse this procedure.

• For casters, use high quality bearing
grease, (yearly).

• Lubricate the slides, (twice yearly).

• Periodically the drawer fronts, drawer
trim, and other surfaces should be

cleaned with a mild detergent and
water.

• Auto wax will preserve the storage
unit's luster finish. Apply the wax as to
a car. The wax will also help protect the

unit against scratches.

• Grease and oil can be removed with
most standard cleaning fluids. For
safety, use a nonflammable cleaning

fluid.

INTENTIONALLY LEFT BLANK