Craftsman 706652650, 706652640, 706651150, 706651131, 706651130 Owner’s Manual

...

ASSEMBLY

INSTRUCTIONS

Chest Model No.

Black 706,651130

Red 706.651150

-- ii I i i --

: ; J

Intermediate Model No.

Black 706,652640

Red 706.652650

Rollaway Model No. Black 706.650110

Red 706.650120

I:'RII MIIN

CHEST

AND

ROLLA WAY

Sold by SEARS, ROEBUCK AND CO,, Chicago, IL 60684 U.S,A.

Printed in U.S.A. F692A1

Aug.!7, 2009 11:09AM Waterloo Grand No,1181 P, 2

__ III

TOOLS REQUIRED

1/4

3/8

C_AF'iYS_A_

7/1 6

9/1 6

BEFORE YOU ASSEMBLE THE CHEST AND ROLLAWAY: Sort out and account for all parts to make sure that you have all necessary materials to

assemble the chest and rollaway. Do not discard packing materials until all parts are accounted for.

NOTE:

Each unit contains a bag of hardware, Listed below are the totals for all three units followed by the number required per unit; _ "

KEY QTY PART NO. A 48 M8738 B 4 MI0665 C 16 M8716

D 8 M6603

DESCRIPTION SCREW 10-24 x 5/16" 24 each:Chest& Rollaway-

SCREW 14-10 x 5/8" Rollaway onl_ =

SCREW 5/16-18 x 3/4" Rollaway only

SCREW :3/8-16 x 3/4" 4 each Chest & intermediate

14-10 x 5/8 10-24 x 5/16

3/8-16 x 3/4

5/16-,18 x 3/4

i II ii . I

Aug17, 2009 11'10AM W&ter!00 Gr_nd

i i= i

I.r WARNING: !

DO NOT ALTER THE PRODUCT IN THE FOLLOWING MANNER:

1) WELDING LOCK BARS OR DOLLIES ONTO THE UNIT.

2) MOUNTING CHEST OR ROLLAWAY ONTO ANY MOVING OBJECT SUCH AS TRUCK

BED, BOAT DECK, OR CAR TRAILER.

j! WARNING: J

STORAGE UNIT WILL TiP IF A NUMBER OF DRAWERS ARE EXTENDED WHICH MAY CAUSE PERSONAL INJURY OR DAMAGE.

IF WARNING: I

BEFORE MOVING UNIT, BE SURE ALL DRAWERS ARE FULLY CLOSED AND LOCKED.

FAILURE TO DO SO MAY CAUSE PERSONAL INJURY OR DAMAGE.

HELPFUL HINTS:

1) Periodically drawer front, pulis and other rollaway and chest surfaces should be cleaned with a milcl detergent end water to keep them looking new.

2) Chest may be attached to the rollaway after the rollaway is assembled with the four 3/8-16 x 3/4" screws (D). Remove the top two drawers of the rollaway and screw

.3/8-16 x 3/4" screws (D) into weldnuts in chest and wrench tighten.

3) For ease of operation, lubricate slide channels periodically with petroJeum jelly,

4) If:it becomes necessary to remove drawers for cleaning or due to damage follow these slide removal instructions.

COMPOUND SLIDES:

A. Pull drawer all the way open then push back 1/16 of an inch. B. Insert a screwdriver into this slot in the slide and push in on the stop un'til it clears the

lance, Repeat the procedure on the other slide and remove drawer.

C. To reinstall drawer, pry stop far enough out to engage lance(3/1 6" to 1/4") and push

drawer onto slides until stops engage lances.

BALL BEARING SLIDES:

A. Pull drawers all the way open.

B. Remove screw and washer from both sides of drawer. C• Lift drawer up and out until tabs in slide clear slots in drawer. D. To reinstall, reverse procedure,

No,1181 P. 3

COMPOUND SLIDE

STO

_ IDE

SCREWDR I_

LUBRI CATE zj'_

m i i in i _

I1 lOAM Waterloo Gra.nd

No.1t81 P. 4

706.651130 BLACK

706.651150 RED

WHEN ORDERING REPLACEMENT PARTS ALWAYS

GIVE THE FOLLOWING INFORMATION:

MODEL NUMBER MODEL DESCRIPTION PART NUMBER PART DESCRIPTION

QUANTITY PART COLOR

I KEY

2 3 4

5 6

7 8

PART NO.

M9316

IM9317A1

T15410 T15409

M10526

T14009A2

M9091A1

A12451

M7413A8

M9400-PA

M7413A11 M8640

BALL STUD

GAS SPRING LOCK BAR COVER

LOCK ROD COVER NAMEPLATE

INSIDE SLIDE ROLLER SLIDE RIGHT

DRAWER

DRAWER LINER DRAWER TRIM

DRAWER LINER DRAWER DIVIDER

DESCRIPTION

KEY

16 17

PART NO.

M10520

M9361A2

IT16874

A12450A1

T15397

M9400A1-PA

A12449

M9090A1

A12450

M10100A1 M1915

F692

NOTE: 1. ALL UNNUMBERED PARTS ARE INTERCHANGEABLE WITH OPPOSITE SIDE.

DESCRIPTION

DRAWER STOP

ACTUATOR ROD

LOCK BAR DRAWER

LOCK BAR DRAWER TRIM

LOCK ROD ASSEMBLY ROLLER SLIDE LEFT

DRAWER LOCK

HANDLE

INSTRUCTION SHEET

5-92

! 22200

+ 7 hidden pages