Craftsman 706597791, 706597790 Owner’s Manual
(RRFTSMRH °
Operator's Manual
SAFETY RULES AND WARNINGS:
• DO NOT stand on this product. You may fall which may cause personal injury.
• WEAR SAFETY GLASSES when removing or repositioning the slides. The tool
could slip which may cause personal injury.
• When moving this product, do not pull it. Push the product to prevent personal injury.
• USE THE BRAKES when not moving this product. This will prevent the product from
rolling, which may cause personal injury or product damage.
• BE CAREFUL when opening more than one drawer. The product may become
unstable and tip, which may cause personal injury or product damage.
• DO NOT mount this product on a truck bed or any other moving object. This may
cause personal injury or product damage.
• DO NOT step in the drawers. You may fall which may cause personal injury.
• Appropriately secure this product before moving it with a forklift.
• DO NOT tow with power equipment. The product could tip, which may cause
personal injury or product damage.
• DO NOT alter this product in any manner. For example, do not weld external
lockbars or attach electrical equipment. This may cause product damage or personal
injury.
• Keep the product on level surfaces. The product may become unstable and tip if
stored or moved on an un-level surface, which may cause personal injury or product
damage.
i i
• BE CAREFUL when closing the cover. Remove hands before the cover closes
completely to prevent personal injury.
• Close the cover and lock the drawers before moving this product. The drawers could
come open and make the product unstable and tip, which may cause personal injury
or product damage.
• The maximum weight for each drawer should be no more than 25 pounds.
• The maximum product weight, including contents, cannot exceed 400 pounds.
Pleaseindicate the following information from the servicepart drawing provided.
Model Number:
Model Description:
CAUTION:
Read and follow all Safety Rules and Operating Instructions before
first use of this product. Retain this document for future reference.
Sears, Roebuck and Co., Hoffman Estates, IL 60179 USA
Call 1-800-4MY-HOME (1-800-469-4663) for Service Parts.
Refer to Service Parts Drawing for full listing of Service Parts.
F1467 2
CASTER INSTALLATION:
Note: Use adequate manpower for this
operation.
• Remove the bottom drawer. See
Operation section: Removing and
Installing Drawers.
• Place the unit on its top. Use the
packaging material to protect the units
finish.
• Attach casters using (4) screws and (4)
nuts per caster. Attach both swivel
casters on the same side of the unit as
the handle.
,\
/
/
\\
\
PARTS TRAY ASSEMBLY:
• The parts tray fits along the front edge of
the roll-away.
• The end pieces (2) attach to the center
piece with two hooks.
• The end pieces have a small slot on one
end to help keep the trays in place.
• Also, the center piece has lids that snap
over the two end pieces as welt.
• There is one small tote tray, which is
removable.
Tote
Tray, _.
Slot .......
PARTS BINS:
• The bottom drawer of the chest has five
parts bins.
• The parts bins tilt in several different
positions for easy access to contents.
• The parts bins are removable and may
hang on the side of the chest or pulled
out drawer.
Parts j
Bin
• For casters, use high quality bearing
grease, (yearly).
• Lubricate the slides, (twice yearly).
• Periodically the drawer fronts, drawer
trim, and other surfaces should be
cleaned with a mild detergent and water.
• Auto wax wilt preserve the storage unit's
luster finish. Apply the wax as to a car.
The wax wilt also help protect the unit
against scratches.
• Grease and oil can be removed with
most standard cleaning fluids. For
safety, use a nonflammable cleaning
fluid.
• Wrench tighten.
BLOCKS:
• Place the riser blocks inthe back corners
of the roll-away.
• Each riser block is labeled with "R" or "L"
for right or left side attachment.
• Be sure to place the hooked edge to the
outside of the roll-away as shown.
/ \
/
/
/
/
CHEST ONTO ROLL-AWAY:
• Carefully place the chest onto the roll-
away.
• Set the chest onto the riser blocks and
the back side of the parts tray.
• The chest does not bolt to the roll-away.
REMOVING AND INSTALLING
DRAWERS:
• Fully extend the drawer. Push it back
1/4".
• Insert a screwdriver into the slot in the
slide and depress the stop until it clears
the lance.
• Repeat the procedure on the other slide.
Remove the drawer.
/ Stop
Lance
• To reinstall the drawer, pry the stop far
enough out to engage the lance (3/16" to
1/4") and push the drawer onto the slides
until the stops pass over the lances.
3 4
Loading...