Craftsman 706597470 Owner’s Manual
BACKWALL WITH METAL PEGBOARD
CAUTION: Backwall MUST be attached to the Workbench before the
top is attached and the drawers are installed.
CAUTION: Read and follow all Safety Rules and Operating Instructions before first use of this product.
Sears, Roebuck and Co., Hoffman Estates, IL 60179, USA.
F1493
f
SAFETY WARNINGS AND CAUTIONS:
Use appropriate safety equipment when using power and hand tools. Failureto do so may cause personal injuryor productdamage.
Use adequate manpower when assemblingand movingthis unit. Failure to do so maycause personal injury or productdamage.
DO NOT stand onthis product.You may fall whichmay cause personal injury.
DO NOT mount this producton a truckbed or any other movingobject.This may cause personal injuryor productdamage.
Appropriatelysecure this product before moving it with a forklift.
DO NOT tow with power equipment. The product could tip, which may cause personalinjuryor product damage.
DO NOT alter this product inany manner. This may cause productdamage or personal injury.
Keep the producton level surfaces. The product may become unstable and tip if stored or moved on an un-level surface, which may
cause personal injury or product damage.
Be sure the workbench is flat on the floor before installingthe Workbench Backwall. Failureto do so maycause personal injuryor
productdamage.
The maximum weight allowed to hang on or be in any waysupported fromthe backwall is65 pounds. Ifthe limitis exceeded the
productmay tip and cause personalinjuryor productdamage.
Be sure to secure the Workbench Backwallto a studdedor concrete wall. Failureto do so may cause the Workbench Backwall and
Workbench to become unstable and tip. This may cause personal injuryor product damage.
Use only the providedpegboardon Workbench Backwall.
BackwallwithMetal Pegboard is only to be attached to one ofthe following Workbenches: 59741, 59742, 59746. Failure to do so
could result in personal injury or productdamage.
r
4
Tools Required:
Socket Wrench
7/16" Socket
Dnll
3/32" Drill Bit
1/8" DrillBit
Screwdriver, Phillips
Screwdriver, Flathead
Hardware Included:
_[_ AA (16) _--_)
BB (3) _ EE (16)
CC (2) FF (2)
DD (16)
GG (1)
(_,all 1-800-4MY-HOME for Service Parts.
(1-800-469-4663)
Refer to Service Parts Drawing for full listing of Service Parts._
E
A(2)
G
F
D
\
\
C(2)
..... :!:!:i:!::'
\
\
\
\
\
\
\
\,
B(2)
H
)
f
f
WARNING: Backwallwith Metal Pegboard isonly to be
attached to one of the following Workbenches:
59741, 59742, 59746
NOTE: To assemblethe Backwall,the drawers and top must
first be removedfrom the workbench.
DRAWER REMOVAL AND INSTALLATION:
FRICTION DRAWERS:
• Emptythe drawer.
• Fullyextend the drawer. Then push it back a fraction of
an inch.
• Insert a screwdriverintothe slotin the slide and
depress the stop untilit clears the lance.
Slot f Stop
Lance
Lubricate
Repeat the procedure for the other slide. Remove the
drawer.
To reinstallthe drawer, prythe stop far enough out to
engage the lance (3/16" to 1/4") and pushthe drawer
onto the slides untilthe stopspass over the lances.
STEP1
AA (2)
DD (2)
EE (2)
Remove and reuse topfastenersinback of
workbench.
Attach A(2).
Fingertighten.
__ Existing
hardware
/
/
BALL BEARING DRAWERS:
Empty the drawer.
• Fully extend the drawer.
• Liftthe release lever on the rightside, while depressing
the leveron the leftside and pullthe drawer out to
remove.
Lever
• To reinstall, carefully align the slides and slowlypush
the drawer into the unituntilthe drawer stops.
TOP REMOVAL:
NOTE: When removingtop, save the screwsto reattach after
backwall is assembled.
Remove and save the screwsfrom the wood top.
Remove top fromworkbench base.
A(2)
FRONT
J
F
STEP2
BB {I)
©
F
STEP 3
AA(2)
DD (8)
BB (2)
EE (S)
DD (2)
• Attach B(2) and C(2).
Finger tighten.
AA
/DD EE
©
Assemble tray.
Fingertighten.
/
BB
Back
EE (2)
EE
DD
AA
/
R,
\
Back
Front
Wrench Tighten
fasteners from
step 1
]
/
/
E
J
Loading...