Craftsman 706954791, 706596232, 706593810, 706591695 Owner’s Manual

CRAFTSMAN °

Operator's Manual

BALL BEARING SERIES

Please indicate the following information from the service part drawing provided.

Model Number:

Model Description:

*Product you purchased may vary from picture shown*

CAUTION:
Read and follow all Safety Rules and Operating Instructions before first use
of this product. Retain this document for future reference.

Sears, Roebuck and Co., Hoffman Estates, IL 60179 USA

FI300

SAFETY WARNINGS AND CAUTIONS:

• The load capacity of the side handle used on all 41" and 52" chests is5001bs when used intandem.

• DO NOT attempt to lift, by the side handles, the 41" and 52" chests using chains, ropes or other liftingdevices
iftwo persons cannot liftthe chest. Use a forklift placed under the bottom of the chest if this situation occurs.

The side handle may fail which may cause personal injury or damage to the product.

• DO NOT stand on this product. You may fall which may cause personal injury.

• WEAR SAFETY GLASSES AND GLOVES when cutting the banding material. The bands may snap which
may cause personal injury.

• WEAR SAFETY GLASSES when removing or repositioning the slides. The tool could slip which may cause
personal injury.

• When moving this product, do not pull it. Push the product to prevent personal injury.

• Handle and swivel casters must be attached on the same side of the product.

• USE THE BRAKES when not moving this product. This will prevent the product from rolling, which may cause
personal injury or product damage.

• BE CAREFUL when opening more than one drawer. The product may become unstable and tip, which may
cause personal injury or product damage.

• DO NOT mount this product on a truck bed or any other moving object. This may cause personal injury or
product damage.

• DO NOT step in the drawers. You may fall which may cause personal injury.

• Appropriately secure this product before moving it with a forklift.

• DO NOT tow with power equipment. The product could tip, which may cause personal injury or product
damage.

• DO NOT alter this product in any manner. For example, do not weld external Iockbars or attach electrical
equipment. This may cause product damage or personal injury.

• A heavy duty side cabinet must be used on an equally heavy duty cart.

• Keep the product on level surfaces. The product may become unstable and tip if stored or moved on an un-
level surface, which may cause personal injury or product damage.

• When the cover is opened, be sure the cover stop is in the locked position. This will prevent accidental
closure and personal injury.

• BE CAREFUL when closing the cover. Remove hands before the cover closes completely to prevent
personal injury.

• The maximum weight for each drawer should be no more than 50 pounds.

• The maximum product weight, including contents, should be no more than 1,000 pounds for RolI-Aways.

• Close the cover and lock the drawers and doors before moving this product. The drawers or doors could
come open and make the product unstable and tip, which may cause personal injury or product damage.

• Remove the work surface, if provided, from the cart before mounting the chest. Failure to do so may cause
the chest to slide off, which may cause personal injury or product damage.

• When locking a chest, close the drawers before closing the cover for lock bars to work properly.

• Spread the weight out evenly in the tote trays. If the weight is not spread evenly, the contents could shift and

fall out, which may cause personal injury, and damage to the contents or tote tray.

VA.=2uflex Nl._t

HARDWARE:

r_.._'.] :hV_I:] Ib'dl

SIDE HANDLE ATTACHMENT:
NOTE: Holes in the unit are tapped requiring no nuts for installation.

• Attach the handle using four 14-10 x 5/8 hex screws. Do not over tighten
the screws.

CASTER INSTALLATION:
NOTE: Use adequate manpower for this operation.

• Remove casterpack from the bottom drawer. Make sure all casters. Screws, and
nuts are accounted for. (16) Screws and nuts.

• Remove the bottom drawer. See operation section: Removing and Installing

Drawers.

• Place the unit on its top. Use the packaging material to protect the paint finish.

• Attach casters using four 1/4-20 x 5/8 hex screws and nuts per caster. Wrench
tighten all screws.

• Return the cart to its upright position.

\

\

[e]'.,1:1t;:ll / [e_

REMOVING AND INSTALLING DRAWERS:

• Empty the drawer.

• Fully extend the drawer.

• Lever Style: Lift or lower (depending on the slide) the
release lever on both sides (this allows the slides to ride

over the stops). Pull out to remove.
Tab Style: Depress the release tab on both sides (this
allows the slides to ride over the stops). Pull out to

remove.

• To reinstall, push the drawer into the slides until the
drawer stops.

• To remove the slide from the unit, first remove the drawer (follow the

procedure above). Lift and hold the spring retainer, and push the slide
upward. The slide may now be removed.

• To reinstall the slide, place the slide in the appropriate position in the

unit. Pull it toward the front of the unit until the spring retainer snaps into
position and secures the slide.

Release
Left

Release
Right

\ \

\-3