Craftsman 706586500, 706586410, 706586400 Owner’s Manual
OPERATOR’S MANUAL
* Product you purchased may vary from picture shown
SERVICE PARTS
CALL 1-800-366-7278 FOR SERVICE PARTS. Refer to Service
Parts Drawing for full listing of Service Parts.
LOCATING MODEL # INFORMATION
Model numbers and other information required for service parts is
located on a label on the interior right side of the top most drawer.
CAPACITIES
• The maximum weight for each drawer should be no more than
100 lbs.
• The maximum product weight for each model combination,
including contents, should be no more than 1,500 lbs.
• Lubricate lock with graphite, (yearly).
• Periodically the drawer fronts, drawer trim, and other surfaces
should be cleaned with a mild detergent and water.
• Auto wax will preserve the unit’s luster nish. Apply the wax
as to a car. The wax will also help protect the unit against
scratches.
• Grease and oil can be removed with most standard
cleaning uids. For safety, use a nonammable cleaning uid.
• It is recommended that drawer liners are used to protect the
nish inside the drawers and to make the drawers easier to
clean. The drawer liners may be cleaned with soap and water.
SAFETY
DANGER is used to indicate a hazardous situation which,
if not avoided, will result in serious injury or death.
WARNING indicates a hazardous situation which,
if not avoided, could result in serious injury or death.
CAUTION is used to indicate a hazardous situation which, if not
avoided, may result in minor injury, moderate injury, or property
damage.
CAUTION: Read and follow all Safety Rules and Operating
Instructions before assembly and rst use of this product.
DANGER
• DO NOT stand on this product. You may fall or cause product
to tip.
• DO NOT open more than one drawer. The product may be-
come unstable and tip.
• DO NOT step in the drawers. You may fall or cause product to
tip.
• DO NOT mount this product on a truck bed or any other mov-
ing object.
• DO NOT move the product prior to closing and locking all the
drawers and chest lid. The drawers could come open and
make the product unstable and tip.
• DO NOT place any objects on top of a closed lid.
WARNING
• WEAR SAFETY GLASSES when removing or repositioning
the slides.
• DO NOT pull the unit, push it when moving. Pushing the unit will
prevent serious ankle and foot injuries.
• USE THE BRAKES when not moving this product. This will
prevent the product from rolling.
• DO NOT alter this product in any manner. For example, do not
weld external lockbars or attach electrical equipment.
• Keep the product on level surfaces. The product may become
unstable and tip if stored or moved on an uneven surface.
• BE CAREFUL when closing drawers, the cover or doors.
Remove hands before the cover closes completely.
CAUTION
MAINTENANCE
Ball bearing slides
• For casters, use high quality bearing grease, (yearly).
• Lubricate the slides with grease or equivalent,(twice yearly.)
Distributed by Sears Brands Management Corporation, Hoffman Estates, IL 60179
• This product is not designed to be directly lifted with a fork lift,
• Do not exceed the maximum weight capacity for each drawer
• This product should be empty when transporting by vehicle.
Properly secure when transporting.
• DO NOT exceed maximum product weight, including contents.
• As with all metal products, this product can contain burrs and
sharp edges. Wear protective gloves during assembly.
• Use adequate manpower when assembling and moving this
unit. Failure to do so may cause personal injury or product
damage.
or to be towed with any mechanical devices.
or shelf.
See Capacities for more information.
F2073
HARDWARE
TOOLS REQUIRED:
3/8-in Wrench
7/16-in Wrench
Cross-tip Screwdriver
HARDWARE INCLUDED:
40- & 52-INCH CABINET HARDWARE
#14 - 10 x 3/4-in Screws
(Qty: 4)
1/4 - 20 x 5/8 Screw (Qty: 16)
1/4-in Nut (Qty: 16)
CASTER INSTALLATION
Items Needed:
1/4 - 20 x 5/8 Screw (Qty: 16)
1/4-in Nut (Qty: 16)
7/16-in Wrench
3/8-in Wrench
Process:
NOTE: Use adequate personnel for this operation.
• Remove the bottom drawer by following the drawer
removal instructions.
• Lay the cabinet down on its back. Use packaging
material to protect the paint nish.
• Mount both swivel casters on the same side of the cart
as the side handle.
• Attach each caster using (4) 1/4-20 x 5/8 screws and
(4) 1/4” nuts per caster.
• Wrench tighten all screws.
• Return the cart to its upright position.
ASSEMBLY
NOTE: Not all assembly instructions will relate to your model.
SIDE HANDLE ATTACHMENT
Items Needed:
#14 - 10 x 3/4 Cross-tip Screw (Qty: 4)
Cross-tip Screwdriver
Process:
• Attach the side handle using (4) #14 - 10 x 3/4 Cross-tip
screws.
• Hand tighten. Do not overtighten.
2
OPERATION
REMOVING DRAWERS
• Empty the drawer.
• Fully extend the drawer.
Button Release
Button Release
REMOVING AND INSTALLING SLIDES
• To remove the slide from the unit, rst remove the
drawer.
• After removing the drawer check to see if the unit has
rivets located on the front of the slide. To drill out rivets,
use a 5/32-in drill bit. The rivets will need to be replaced
with 5/32-in rivets.
• To reinstall the slide in the appropriate position in the
unit, align front and back lances with mounting holes in
the side of the unit. Pull towards the front of the unit and
downwards until rivet holes in slide line up with holes in
the unit. The rivets will need to be replaced with 5/32-in
rivets.
• For smooth operation, make sure the drawers are
matched with their original slides.
Drill out rivet
• Push the buttons on the right and left side.
• Pull out drawer to remove.
INSTALLING DRAWERS
Ball bearing slide - Pull slides and slide carrier out to fully
extended position (see illustration.) Hold the slide on the
cabinet while aligning it with the slide on drawer. Slightly
insert one side and repeat for the other side. Slowly push
drawer to its fully closed position to engage slide. Open
drawer and reclose to ensure proper operation.
Slide carrier
Slide
OPENING TOP CHEST DRAWERS
• Locate the drawer lock lever in the center, back of the
top chest open till area.
• Move lever to the right to unlock.
• Move lever to left to lock.
Note: Drawers are only locked when the lever is in the
“locked” postion. To secure all the content in the top chest,
lock drawers with the lock lever, close lid and lock lid with
key.
Unlocked
position
3
Loading...