Craftsman 706466390, 706466370, 70646630 Owner’s Manual

OPERATOR'S MANUAL

CRRFrSMFIN°

FLOOR CABINET

TRIO / LOCKER / SHELVES

* Product you purchased may vary from picture shown

• Lubricate the slides with grease or equivalent, (twice yearly.)

• Lubricate lock with graphite, (yearly).

• Periodically the drawer fronts, drawer trim, and other surfaces

should be cleaned with a mild detergent and water.

• Auto wax will preserve the unit's luster finish. Apply the wax
as to a car. The wax will also help protect the unit against

scratches.

• Grease and oil can be removed with most standard
cleaning fluids. For safety, use a nonflammable cleaning fluid.

DANGER ,A is used to indicate a hazardous situation which,
if not avoided, wil.._Jresult in serious injury or death.

WARNING z_ indicates a hazardous situation which,
if not avoided, could result in serious injury or death.

CAUTION is used to indicate a hazardous situation which, if not
avoided, may result in minor injury, moderate injury, or property

damage.
CAUTION: Read and follow all Safety Rules and Operating

Instructions before first use of this product.
DANGER ,_

• DO NOT stand on this product. You may fall or cause product

to tip.

• DO NOT mount this product on a truck bed or any other moving

object. This may cause personal injury or product damage.

• DO NOT open more than one drawer. The product may be-

come unstable and tip.

• DO NOT step in the drawers. You may fall or cause product to

tip.

• DO NOT step on the shelves. You may fall or cause product to

tip.

CALL 1-800-469-4663 FOR SERVICE PARTS. Refer to Service
Parts Drawing for full listing of Service Parts.

LOCATING MODEL # INFORMATION
Model numbers and other information required for service parts is

located on a label on the interior right side of the top most drawer.

• The maximum weight for each shelf in a door should be no more
than 7 Ibs.

• The maximum weight for each half shelf in cabinet should be no

more than 50 Ibs.

• The maximum weight for each full shelf in cabinet should be no

more than 100 Ibs.

• The maximum weight for each drawer in cabinet should be no

more than 100 Ibs.

• The maximum product weight, including contents, should be no

more than 400 Ibs.

Distributed by Sears Brands Management Corporation, Hoffman Estates, IL 60179 F1999 REV A

WARNING

• Use appropriate safety equipment when using power
and hand tools. Failure to do so may cause personal
injury or product damage.

• Use adequate manpower when assembling and moving

this unit. Failure to do so may cause personal injury or

product damage.

• DO NOT alter this product in any manner. For example, do not
weld external Iockbars or attach electrical equipment.

• Keep the product on level surfaces. The product may become
unstable and tip if stored or moved on an uneven surface.

• Cabinet MUST be attached to a stud in a wood frame wall.
Failure to do so may cause personal injury or product damage

CAUTION

• Appropriately secure this product before moving it with
a forklift.

• The maximum weight for each drawer should never be
exceeded.

• Only transport this product empty. Properly secure when

transporting.

TOOLS REQUIRED:

Drill
1/4" Driit Bit

1/8" Ddi[ Bit

5/32" Hex Key

HARDWARE INCLUDED:

items Needed:
Screw Leveler (Qty: 4)

Process:

- Lay the cabinet on its back. Use packaging material to

protect the finish.

- Instatt (4) Screw Levelers.
Return the cabinet to its upright position.

[_ 1/4-20 3/4" Button Head Screw

X

(Qty: 3)

1/4-20 Serrated Ftange Nut (Qty: 3)

Screw Leveler (Qty: 4)

Snap Grommet (Qty: 2)

Shelf Bracket (Qty: 1)

Mounting Bracket (Qty: 1)

NOTE: Some adjustments may be necessary after cabinet
is in desired location.

items Needed:
1/4-20 x 3/4" Button Head Screw (Qty: 2)

1/4-20 Serrated Ftange Nut (Qty: 2)
Shelf Bracket (Qty: 1)

PrOCeSS:

- Mount to unit using (2) 1/4-20 x 3/4" Button Head

Screws, and (2) 1/4-20 Serrated Flange Nuts.
Adjust bracket for tock cam to tatch.

_" Screw

o

Nut

ItemsNeeded:
1/4-20x3/4"ButtonHeadScrew(Qty:1)

1/4-20SerratedFlangeNut(Qty:1)
MountingBracket(Qty:1)

Process:

NOTE: Mounting bracket may be mounted on either side

of the cabinet. Mounting shown on left side.

Place Mounting Bracket in desired mounting location.
Mark center of mounting hole location, using slots in
bracket as a template.

Remove bracket. Drill 1/8" mounting hole.

- Mount to unit using (1) 1/4-20 x 3/4" Button Head
Screws, and (1) 1/4-20 Serrated Flange Nuts.
Finger tighten.

Nut

o _ _± o

Q SHELF ADJUSTMENT

Empty shelf.
Remove fasteners.

Reattach shelf.

Mounting
Bracket

WARNING: Cabinet MUST be attached to a stud in a wood
frame wail. Failure to do so may cause personal injury or

product damage.

Wood frame wail, concrete or other surfaces require

hardware for mounting. Use appropriate hardware per your
local building codes. Failure to do so may cause personal
injury or product damage.

Atign cabinet with a stud. Adjust Leveter feet if needed.

Drill 1/8" pilot hole.

- Attach cabinet to stud using appropriate screw.

Screw

_,_ LEVELING FOOT ADJUSTMENT

Adjust Screw Leveler to desired position with Flathead

Screwdriver or 7/16" open end wrench as shown.

O DOOR CLOSURE

Ensuring the cabinet is level (front to back) will result in

the correct alignment of the doors and proper function of
the magnetic door closure system.