Craftsman 706461810, 706461800, 706405000, 706404420 Owner’s Manual
OPERATOR'S MANUAL
s -
®
Friction slides
HOMEOWNER TOOL CHESTS oPeriodically the drawer fronts, drawer trim, and other surfaces
should be cleaned with a mild detergent and water.
Auto wax wilt preserve the unit's luster finish. Apply the wax as
to a car. The wax wilt also help protect the unit against scratch-
es.
Grease and oil can be removed with most standard cleaning
fluids. For safety, use a nonflammable cleaning fluid.
If drawer liners are supplied, it is recommended they are used
to protect the finish inside the drawers and to make the drawers
easier to clean. The drawer liners may be cleaned with soap and
water.
. q
DANGER _, is used to indicate a hazardous situation which,
if not avoided, wit_[result in serious injury or death.
WARNING z_ indicates a hazardous situation which, if not
avoided, could result in serious injury or death.
CAUTION is used to indicate a hazardous situation which, if not
avoided, _ result in minor injury, moderate injury, or property
damage.
CAUTION: Read and follow all Safety Rules and Operating
Instructions before first use of this product.
* Product you purchased may vary from picture shown
CALL 1-800-388-7278 FOR SERVICE PARTS. Refer to Service
Parts Drawing for full listing of Service Parts.
LOCATING MODEL # INFORMATION
Model numbers and other information required for service parts is
located on a label on the interior right side of the top most drawer.
The maximum weight for each drawer should be no more than
25 Ibs.
The maximum product weight, including contents, should be no
more than 500 tbs. for each model combination with 4 x 2 inch
casters and friction style drawer slides
For casters, use high quality bearing grease, (yearly).
Lubricate the slides with grease or equivatent,(twice yearly.)
Lubricate lock with graphite, (yearly).
DANGER A
DO NOT stand on this product. You may fall, which may cause
personal injury.
DO NOT step in drawers. You may fall, which may cause personal
injury.
USE THE DRAKES when not moving this product. This will pre-
vent the product from rolling, which may cause personal injury or
product damage.
APPROPRIATELY SECURE this product before moving with a
forklift.
• DO NOT tow with power equipment. The product could tip, which
may cause personal injury or prduct damage.
WARNING Z_
WEAR SAFETY GLASSES when removing or repositioning the
slides. The tool could slip, which may cause personal injury.
DO NOT mount this product on a truck bed or any other moving
object. This may cause personal injury or product damage.
DO NOT alter this product in any manner. For example, do not
weld external lockbars or attach electrical equipment. This may
cause personal injury or product damage.
UNIT MUST BE located on a level surface. The product may be-
come unstable and tip if stored or moved on an unqevet surface,
which may cause personal injury or product damage.
LOCK the drawers before moving this product. The drawers could
come open and make the product unstable and tip, which may
cause personal injury or product damage.
DO NOT pull this product when moving it. Push the product to
prevent personal injury.
v H i
CAUTION
DE CAREFUL when opening more than one drawer. The product
may become unstable and tip, which may cause personal injury or
product damage.
Sears Brands Management Corporation, Hoffman Estates, IL 60179 USA F1977
TOOLS REQUIRED:
Ftat4ip Screwdriver
3/8-in Wrench
7/16-in Wrench
5/16-in Drill Bit
HARDWARE REQUIRED:
MIDDLE CHEST
1/4 - 20 x 5/8" (Qty: 4)
@
1/4 - 20 Nut (Qty: 4)
CASTER INSTALLATION
Items Needed:
1/4 - 20 x 5/8 Screw (Qty: 16)
1/4 - 20 Nut (Qty: 16)
Process:
NOTE: Use adequate manpower for this operation.
Open and remover the bottom drawer. (See operation
"Removing Drawers")
Lay the unit on its back, use packaging material to
protect the paint finish.
Attach the casters to unit using (4) 1/4 - 20 x 5/8 screws
and (4) 1/4 - 20 nuts per caster. Mount both swivel
casters on the same side of the unit. Wrench4ighten.
Return the unit to its upright position.
Reinstall bottom drawer.
HARDWARE REQUIRED:
CABINET
1/4 - 20 x 5/8" (Qty: 16)
@
Chest:
Literature
Cabinet:
Literature
Hardware bag
Caster pack
1/4 - 20 Nut (Qty: 16)
Caster pack
Nut
.........._
Bolt
OPTION I oMOUNTING TOP CHEST TO MIDDLE CHEST
Remove enough drawers to access the top and bottom
mounting surfaces of the units (refer to the drawer
removal instructions).
Place the chest in the desired location on top of the
middle chest and mark the mounting hole locations.
Remove the chest and drill four 5/16" (8mm) holes
through the top of the middle chest.
Secure the units together using four 1/4- 20 x 5/8 inch
screws.
- Wrench tighten att screws.
- Replace the drawer (refer to the drawer installation
instructions).
- To remove the chest, reverse the procedure.
REMOVINGANDiNSTALLiNGDRAWERS
Fullyextend the drawer. Push it back 1/4 inch.
Insert a screwdriver into the slot in the slide and depress
the stop until itclears the lance.
Repeat the procedure on the other slide. Remove the
drawer.
Jbricate
To reinstall the drawer, prythe stop far enough out to
engage the lance (3/16" to 1/4") and push the drawer onto
the slides until the stops pass over the lances.
REINSTALL DRAWERS
Friction stide =Fully extend slides in cabinet. Hold the
slide on the cabinet while alighning it with the slide on
the drawer. Push the drawer into the unit until the drawer
fully engages slides. Open drawer and rectose to ensure
proper operation. (If stop does not engage slide, lightly
deflect the stop with a screwdriver.)
TO LOCK CHEST
Insert the tockbar (which stores in the top tray), tabbed
end up, into the slot in the top tray and down into the
slot inthe base. Close the cover and lock with the key.
TO LOCK ROLLING CABINET
The tockbar for the cabinet is stored in a slot in the top
front corner of the unit.
Insert the straight end of the tockbar into the slot in
the base.
Move the tockbar toward the unit until the bent end fits
into the slot near the lock. Lock with the key.
Loading...