Craftsman 70645280 Owner’s Manual
OPERATOR'S MANUAL
LOCKERS
CALL 1o800o833o4405 FOR SERVICE PARTS. Refer to Service
Parts Drawing for futt listing of Service Parts.
LOCATING MODEL # iNFORMATiON
Model numbers and other information required for service parts is
located on a label on the interior right side of the top most drawer.
DANGER _ is used to indicate a hazardous situation which,
if not avoided, wit===Jresult in serious injury or death.
WARNING z_ indicates a hazardous situation which, if not
avoided, could result in serious injury or death.
CAUTION is used to indicate a hazardous situation which, if not
avoided, _ result in minor injury, moderate injury, or property
damage.
CAUTION: Read and follow all Safety Rules and Operating
Instructions before first use of this product.
DANGER
- DO NOT stand on this product. You may fatt or cause product to
tip.
DO NOT open more than one drawer. The product may become
unstable and tip.
DO NOT step in the drawers. You may fatt or cause product to
tip.
DO NOT mount this product on a truck bed or any other moving
object.
Lock the door before moving this product. The door could come
open and make the product unstable and tip, which coutd cause
personat injury or product damage.
WARNING z_
WEAR SAFETY GLASSES when removing or repositioning
the stides.
DO NOT tow with power equipment. The product may cause
personal injury or product damage.
DO NOT alter this product in any manner. For example, do not
weld extemat iockbars or attach electrical equipment.
Keep the product on level surfaces. The product may become
unstable and tip if stored or moved on an uneven surface.
• A heavy duty side cabinet must be used on an equally heavy
duty cart.
" E1v 'it1 - I
• Empty weight 147 Ibs.
• The maximumproduct weight, includingcontents, should be no more
than 400 pounds.
Lubricate the stides with grease or equivalent,(twice yearly.)
Lubricate lock and locking system components with graphite,
(yearly).
Periodically the drawer fronts, drawer trim, and other surfaces
should be cleaned with a mild detergent and water.
Auto wax wiii preserve the unit's luster finish. Apply the wax as
to a car. The wax wiii also help protect the unit against scratch-
es.
Grease and oil can be removed with most standard cleaning
fluids. For safety, use a nonflammable cleaning fluid.
if drawer liners are supplied, it is recommended they are used
to protect the finish inside the drawers and to make the drawers
easier to clean. The drawer liners may be cleaned with soap and
water.
CAUTION
DO NOT exceed maximum product weight, including contents.
See Operations Sections: Capacities for more information.
USE ADEQUATE MANPOWER WHEN LIFTING OR IVIOVo
ING THE CHEST OR CABINET.
Waterloo Industries, 139 West Forest Hill Avenue, Oak Creek, WI 53154, USA F1995
TOOLS REQUIRED:
Screwdriver
Cross-tip Screwdriver
3/8" Wrench
BRACKET INSTALLATION
Items Needed:
3/8-16 x 3/4 Pan Head Screw (Qty: 2)
Cross-tip Screwdriver
Hardware Inc_uded:
_}) _1 _\_1 3/8-16 3/4 Pan Head Screw
X
(Qty: 2)
(_ _ 14-10 x 5/8 Hex Screw (Qty: 2)
Locker:
Literature
Hardware bag
Upper Bracket
Note: The hanging brackets and bumpers can be
mounted to either side of the cabinet.
Process:
- Attach the adhesive-backed rubber bumpers at the
bottom corners of the side cabinet.
Attach the bracket to the side of the cabinet using two
3/8-16 x 3/4 pan head screws.
Bracket
Lower Bracket
Bumper
Drawer Liner Roll
Screw
Bumper
Lower
Bracket
REVERSIBLE DOOR MOUNTING INSTRUCTIONS
TO MOUNT DOOR TO OPPOSITE SIDE
Items Needed:
Screwdriver
Process:
- Remove door and hinge assembly by removing screws
on hinge.
Turn upside down and refit to opposite side using the
same screws.
Note: Adjust door to assure optimum performance prior ro
wrench tightening screws.
ATTACHINGSIDECABINETTOUNiT
itemsNeeded:
14-10x5/8HexScrew(Qty:2)
3/8"Wrench
Beforeinstallingthesidecabinet,removethehandle
byfollowingthesidehandleinstructions. The chest
must be moved for the locker attachement. Reattach
chest to cabinet before moving the unit.
PrOCeSS:
- Using adequate help hang the locker on the unit.
- Place the bottom bracket over the bottom flange of the
unit and attach to the underside of the side cabinet using
two 14-10 x 5/8 hex screw.
J
J
o _ :± ®
' REMOVING AND iNSTALLiNG DRAWERS
Q
Empty the drawer.
Fully extend the drawer.
Release Left
Release Right
Side
Cabinet
Lower
Bracket Screw
_!_ REMOVING AND iNSTALLiNG SLIDES
Slide Removal -
- The drawers in these units can be rearranged to fit your
specific needs. This means that drawers may be moved
or replaced as desired. For example, a 6=inch drawer
may be replaced by a 2-inch and a 4-inch drawer, or
three 2-inch drawers.
- First remove the drawer (Refer to Operation A).
- Lift and hold the spring retainer, and push the slide to=
ward the rear of the unit. The slide may now be removed.
Spring Retainer
Slide Installation -
Place the slide in the appropriate position in the unit and
pull toward the front of the unit until the spring retainer
snaps into position and secures the slide.
For smooth operation, make sure that the drawers are
matched with their original slides.
Loading...