Craftsman 706452750, 706452760, 706452720, 706452710 Owner’s Manual

OPERATOR'S MANUAL

CRFIFrSMRH°

[ s, L 1

• Periodically the drawer fronts, drawer trim, and other surfaces
should be cleaned with a mild detergent and water.

• Auto wax will preserve the unit's luster finish. Apply the wax
as to a car. The wax will also help protect the unit against
scratches.

• Grease and oil can be removed with most standard
cleaning fluids. For safety, use a nonflammable cleaning fluid.

• If drawer liners are supplied, it is recommended they are used

to protect the finish inside the drawers and to make the drawers

easier to clean. The drawer liners may be cleaned
with soap and water.

INDUSTRIAL ROLLER CABINET

564NCH CABINET

MAXIMUM WEIGHT LIMIT (4800) LBS.

75=INCH CABINET

MAXIMUM WEIGHT LIMIT (5600) LBS.

CALL 1-800=833-4405 FOR SERVICE PARTS. Refer to Service
Parts Drawing for full listing of Service Parts.

LOCATING MODEL # INFORMATION
Model numbers and other information required for service parts is

located on a label on the interior right side of the top most drawer.

• The maximum weight for each 2-inch deep drawer is
120 pounds.

• The maximum weight for each drawer 3-inches deep or more is

200 pounds.

• The maximum weight for the top 4-inch drawer on roller cabinets

is 320 pounds.

• The maximum weight for each drawer 9-inches deep or more is

400 pounds.

DANGER ,_ is used to indicate a hazardous situation which,
if not avoided, will result in serious injury or death.

WARNING /K indicates a hazardous situation which,
if not avoided, could result in serious injury or death.

CAUTION is used to indicate a hazardous situation which, if not
avoided, may result in minor injury, moderate injury, or property

damage.
CAUTION: Read and follow all Safety Rules and Operating

Instructions before first use of this product.

DANGER ,_

• DO NOT stand on this product. You may fall or cause product
to tip.

• DO NOT open more than one drawer. The product may
become unstable and tip.

• DO NOT step in the drawers. You may fall or cause product
to tip.

• DO NOT mount this product on a truck bed or any other
moving object.

• DO NOT move the product prior to closing and locking all the

drawers. The drawers could come open and make the product
unstable and tip.

• The work surface must be removed if a chest is placed on top

of a cabinet. Stacked products should be bolted together. The

products could become unstable and tip.

WARNING z_

• WEAR SAFETY GLASSES when removing or repositioning
the slides.

• DO NOT pull the unit, push it when moving.

• USE THE BRAKES when not moving this product. This will

prevent the product from rolling.

• DO NOT alter this product in any manner. For example, do not

weld external Iockbars or attach electrical equipment.

• Keep the product on level surfaces. The product may become

unstable and tip if stored or moved on an uneven surface.

CAUTION

• This product is not designed to be directly lifted with a fork lift, or
to be towed with any mechanical devices.

• The maximum weight for each drawer should never be exceeded.

• Only transport this product empty. Properly secure when trans-

porting.

• DO NOT exceed maximum product weight, including contents.

Ball bearing slides

• For casters, use high quality bearing grease (yearly).

• Lubricate the slides with grease or equivalent(twice yearly.)

• Lubricate lock with graphite (yearly).

Waterloo Industries, 139 West Forest Hill Avenue, Oak Creek, WI 53154, USA F1997

See Capacities for more information.

Use spacer blocks (1-1/2 minimum) in front and back for support
when lifting your box. Place support blocks as close to front and

back flanges as possible•

Always use adequate support to lift your box. Failure to do so
could result in product damage•

B,ocb,

1-1/2" min _z

support block F\
front and back i

TOOLS REQUIRED:
Screwdriver

SiDE HANDLE ATTACHMENT

° Attach handle using four 1/4-20 x 1-1/2 screws•

• Tighten with screwdriver•

REMOVING AND INSTALLING DRAWERS

NOTE: The drawers in these units can be rearranged

to fit your specific needs. This means that drawers

may be moved or replaced as desired. For example, a
{}-inch drawer may be replaced by a 2-inch and a 4=
inch drawer, or three 2=inch drawers. The quick
release slides detach easily from the drawers and the

unit.

HARDWARE INCLUDED:

1/4-20 x 1-1/2 Hex Screw
(Qty: 4)

Cabinet:

Literature
Hardware Bag

Handle

• Empty the drawer•

• Fully extend the drawer•

Release

LeverStyle- Lift or lower, depending on the slide, the

release lever on both sides, (this allows the slides to ride
over the stops.) Pull out to remove.

Tab Style - Depress the release tabs on both sides,
(this allows the slides to ride over the stops.)

Pull out to remove.

REMOVING AND iNSTALLiNG SLIDES

To remove the slide

• Remove the drawer. (See drawer removal section.)

• Position inside of slide for access. Remove retaining
screw from front slide connection.

• Push the slide toward back of unit to remove.

Retaining

To reinstall the slide

• Place the slide in the desired position in the unit.

• Pull the slide toward the front of the unit.

• Reinstall retaining screw to lock slide in place.

iNSTALLiNG DRAWERS

Ball bearing slide - Pull slides and slide carrier out to fully

extended position (see illustration.) Hold the slide on the
cabinet while aligning it with the slide on drawer. Slightly
insert one side and repeat for the other side. Slowly push
drawer to its fully closed position to engage slide. Open

drawer and reclose to ensure proper operation.

slide carrier

/

LOCKING THE UNiT

• Make sure drawers are fully closed.

• Insert the key and turn fully to the left.

• Return key to center position to remove key.

UNLOCKING THE UNiT

° insert the key and turn fully to the right.

• Return key to center position to remove key.