Craftsman 706452740, 706452730, 706452700, 70645270 Owner’s Manual

OPERATOR'S MANUAL

INDUSTRIAL CANOPY

®

DANGER is used to indicate a hazardous situation which,
if not avoided, wit__Jiresult in serious injury or death.

WARNING z_ indicates a hazardous situation which,
if not avoided, could result in serious injury or death.

CAUTION is used to indicate a hazardous situation which, if not
avoided, _ result in minor injury, moderate injury, or property

damage.
CAUTION: Read and follow all Safety Rules and Operating

instructions before first use of this product.

DANGER

- DO NOT stand on this product. You may fatt or cause product
to tip.
DO NOT mount this product on a truck bed or any other moving

object.

WARNING A

- Use appropriate safety equipment when using power and hand
tools.

- DO NOT alter this product in any manner. For example, do not

weld externat iockbars or attach electrical equipment.

- Use adequate manpower when assembling and moving this
unit.

- Keep the product on ievei surfaces. The product may become

unstable and tip if stored or moved on an uneven surface.

- BE CAREFUL when closing the cover. Remove hands before

the cover closes completely.

- DO NOT step on the shelves.

CALL 1-800-833-4405 FOR SERVICE PARTS. Refer to Service
Parts Drawing for fuji listing of Service Parts.

LOCATING MODEL # iNFORMATiON
Model numbers and other information required for service parts is

located on a label on the interior right side.

Lubricate the slides with grease or equivaient,(twice yearly.)
Lubricate lock with graphite, (yearly).

Periodically surfaces should be cleaned with a mild detergent

and water.

Auto wax wiii preserve the unit's luster finish. Apply the wax
as to a car. The wax wiii also help protect the unit against
scratches.

Grease and oil can be removed with most standard
cleaning fluids. For safety, use a nonflammable cleaning fluid.

CAUTION

- Appropriately secure this product before moving it with a
forklift.

Waterloo Industries, 139 West Forest Hill Avenue, Oak Creek, WI 53154, USA F1996

TOOLS REQUIRED:

Socket Wrench Hammer
5/16-in Socket Center Punch

3/8-in Socket Ddil

1/2-in Socket 1!2-in Drill Bit

Cross-tip Screwdriver Tape Measure
Torx Screwdriver

HARDWARE INCLUDED:

1/4 - 20 x 5/8-in Carriage Bolt
(Qty: 20)

#14 - 10 x 5/8 Hex Washer

Screw (Qty: 4)

1/4 - 20 x 7/16 Hex Washer
Screw (Qty: 8)

Bushing (Qty: 2)

Grommet (Qty: 2)

Grommet (Qty: 2)

Long Hinge Pin (Qty: 2)

Short Hinge Pin (Qty: 2)

©

©

#8 - 32 x 1/2 Torx Self Tapping

Screw (Qty: 4)

#6 - 32 x 1/2 Pan Head Screw

(Qty: 2)

5/16 Washer (Qty: 24)

1/4 - 20 Flange Nut (Qty: 24)

#6 - 32 Hex Nut (Qty: 4)

Plastic Rivet (Qty: 11)

14 - 10 x 1-1/2 Hex Washer
Screw (Qty: 7)

1/4 - 20 x 2-1/4 Carriage Bolt
(Qty: 4)

Top

Back / S!de

Left
S!de

Lock Rod Door

Right

Top
Pane!

Lower

End Cap (Qty: 2)

Gas Strut (2) _:_ ..........................Outlet

Corner Brace (4)

Magnetic Light

BACK, SIDE AND TOP CONSTRUCTION

Items Needed:

1/4 - 20 x 5/8-in Carriage Bolt (Qty: 15)

5/16 Washer (Qty: 15)

1/4 - 20 Flange Nut (Qty: 15)

+

UPPER DOOR ASSEMBLY

Items Needed:
1/4 - 20 x 5/8-in Carriage Bolt (Qty: 5)

5/16 Washer (Qty: 9)
1/4 - 20 Flange Nut (Qty: 9)
1/4 - 20 x 2-1/4 Carriage Bolt (Qty: 4)

PrOCeSS:

+Assemble back to left side and right side using (4) bolts,

(4) washers, and (4) nuts in each side.

Left Side Flange

Nut

Washer

Front

Carriage
Bolt

Back

Back

Right
Side

+Attach top to unit using (7) bolts, (7) washers, and (7)

nuts.
Square the unit and wrench tighten all fasteners.

Process:

NOTE: Finger tighten all fasteners until instructed to
wrench tighten.

Assemble top panel and front panel using (5) bolts, (5)
washers and (5) nuts.
The top panel should be outside of the front panel.

Install (4) corner braces using (2) bolts, (2) washers, and

(2) nuts in each set.
Square the unit and wrench tighten all fasteners

Corner

Brace _ l_

Front Panel _ U_,_

Bolt "_"-. J_ _---_"_----- Coa[;dage

_e_ _'N F_ang_ :_shern

Washer

Nut

Bolt

Front

Top

i .......

L................... ,

D

o

.........+..............€

i

MOUNTING UPPER DOOR

items Needed:
Bushing (Qty: 2)

#14 - 10 x 5/8 Hex Washer Screw (Qty: 2)
Long Hinge Pin (Qty: 2)

LOCK INSTALLATION
Items Needed:

Grommet (Qty: 2)

PrOCeSS:

- Snap shaft ends of struts (J) over bail studs on canopy
sides as shown.

Ball Stud

Gas Strut

- install (2) bushings in square holes in sides of unit as
shown.

Attach door assembly to unit using (2) tong pivot pins

and (2) screws.

Wrench tighten screws. Do not overtighten.

Process:

- InstatJ (2) grommets in outside hoJes of stiffeners on
lower door.

Mount lock to door as shown, using mounting nut and

two brackets.

insert the key and rotate the lock 90 ° CCW to the lock

position.

insert one end of the lock rod through a stiffener and

through grommet as shown.

Repeat for the other end of the lock rod.
Attach lock rod to the lock using adaptor nut as shown.
Because Jock is in "Lock" position, rotate lock CW 180 °

to "UnJock."

Return the key to the middle position and remove key.

Grommet

Adaptor Nut

Supplied with Lock

NOTE: The ball studs for the door assembly are
located on the outside of the stiffener on the door,

near the hinge pins.

Snap piston end of struts over bah studs on the door

assembly.

Screw Square Hole

Bushing

Ball Stud Doo_

Mounting
Nut

Washer

Lock

.1

/S _ " MounttngNut

"_ Supplied w_th Lock

X

Lock

Brackets

Lock Rod

@tor Nut

Supplied with
Lock

Rod