Craftsman 706407610 Owner’s Manual

OPERATOR'S MANUAL

CRRFTSMRN

Ball bearing slides Friction slides

BASIC PROJECT CENTERS

Some instructions and drawings may not apply to

your specific unit.

CALL 1-800-366-7278FOR SERVICE PARTS. Refer to Service Parts Drawing for full listing of Service Parts.

LOCATING MODEL # INFORMATION Model numbers and other information required for service parts is

located on a label on the interior right side of the top most drawer.

• The maximum weight for each drawer should be no more than 25 Ibs. for friction slides or 30 Ibs. for ball-bearing slides

• The maximum product weight, including contents, should be no

more than 400 Ibs.

• For casters, use high quality bearing grease (yearly).

• Lubricate the slides with grease or equivalent (twice yearly.)

• Lubricate lock with graphite (yearly).

Sears Brands Management Corporation, Hoffman Estates, IL 60179 USA F1973

• Periodically the drawer fronts, drawer trim, and other surfaces should be cleaned with a mild detergent and water.

• Auto wax will preserve the unit's luster finish. Apply the wax as

to a car. The wax will also help protect the unit against scratch-

es.

• Grease and oil can be removed with most standard cleaning

fluids. For safety, use a nonflammable cleaning fluid.

• If drawer liners are supplied, it is recommended they are used

to protect the finish inside the drawers and to make the drawers

easier to clean. The drawer liners may be cleaned with soap and water.

DANGER ,_, is used to indicate a hazardous situation which, if not avoided, will result in serious injury or death.

WARNING A'X indicates a hazardous situation which, if not avoided, could result in serious injury or death.

CAUTION is used to indicate a hazardous situation which, if not avoided, _ result in minor injury, moderate injury, or property

damage. CAUTION: Read and follow all Safety Rules and Operating In-

structions before first use of this product. DANGER ,_

• DO NOT stand on this product. You may fall or cause product to

tip.

• DO NOT open more than one drawer at a time. The product may become unstable and tip.

• DO NOT step in the drawers. You may fall or cause product to

tip.

• DO NOT mount this product on a truck bed or any other moving object.

• DO NOT move the product prior to closing and locking all the drawers. The drawers could come open and make the product

unstable and tip.

WARNING z_

• WEAR SAFETY GLASSES when removing or repositioning the slides.

• DO NOT pull this product when moving it. Push the product to prevent personal injury.

• USE THE BRAKES when not moving this product. This will pre- vent the product from rolling.

• DO NOT alter this product in any manner. For example, do not weld external Iockbars or attach electrical equipment.

• Keep the product on level surfaces. The product may become unstable and tip if stored or moved on an uneven surface.

• BE CAREFUL when closing the cover. Remove hands before

the cover closes completely.

CAUTION

• This product is not designed to be directly lifted with a fork lift, or

to be towed with any mechanical devices.

• The maximum weight for each drawer should never be exceed- ed.

• Only transport this product empty. Properly secure when trans- porting.

• DO NOT exceed maximum product weight, including contents. See Capacities section for load rating.

TOOLS REQUIRED: Screwdriver flathead

7/16" Wrench 3/8" Wrench

Rubber Mallet

HARDWARE REQUIRED: HARDWARE MAY VARY DEPENDING ON PROJECT

CENTER MODEL

]1111111111111111>#14-10 x 5/8 Screw (Qty: 4)

1/4 - 20 Nut (Qty: 16)

Project Center Handle Literature Tool Holder

Hardware bag Caster pack

NOTE: Not all assembly instructions will apply to your

model.

TOOL HOLDER AND HANDLE INSTALLATION

Items Needed: Grommet (Qty: 4)

#14 - 10 x 5/8 Screw (Qty: 4)

lllllllll>

Grommet (Qty: 4)

1/4 - 20 x 5/8 Screw (Qty: 16)

#14 - 10 x 3/4 Screw (Qty: 7)

#8 x 1.25 Screw (Qty: 4)

(used to mount outlet strip)

1/4 - Washer (Qty: 7)

• Insert (4) Grommets in (4) square mounting holes (two in each side). May need to tap into place with a hammer.

• Install the handle on the same end as the swivel casters by inserting the tabs under the plastic top.

• Attach with (2) #14 - 10 x 5/8 screws and wrench-tighten.

Do not overtighten.

• Attach the tool holder to the other end of the unit in the same manner.

_(4)

Handle

Grommet

Tab

. (4)

Plug (Qty: 1)

Tool

holder

CASTER INSTALLATION Items Needed:

1/4 - 20 x 5/8" (Qty: 16) 1/4 - 20 Nut (Qty: 16)

7/16-in Wrench

Process:

• Remove the bottom drawer. See operation section: Re- moving and Installing Drawers.

• Lay the cabinet on its back. Use packaging material to protect the finish.

• Attach the casters using (4) 1/4 - 20 x 5/8" screws and (4) 1/4 - 20 nuts per caster. Mount both swivel casters on

the same side of the unit as the side handle.

• Wrench tighten all screws.

• Return the unit to its upright position.

• Reinstall bottom drawers.

• Attach the top to the unit using (3) #14-10 x 3/4" screws and (3) 1/4" washers. Be sure the individual tops are snug against each other.

• Complete top attachment using (4) #14-10 x 3/4" screws and (4) 1/4" washers.

Screw

OUTLET STRIP INSTALLATION

Items Needed: #8 x 1.25 Screw (Qty: 4)

• Attach outlet strip to plastic top using the screws (4) provided with the outlet strip.

PLASTIC TOP INSTALLATION

Items Needed: #14 - 10 x 3/4 Screw (Qty: 7)

1/4 - Washer (Qty: 7)

• Slide the two plastic top pieces together and place on the unit.

• Insert plug into hole in the plastic top. NOTE: To use this hole for cord management, remove the center portion of the plug before installing.

• Place wood top on the plastic top.

NOTE:Notalloperationinstructionswillrelatetoyour

model.

LOCKINGBAR NOTE:Thelockingbarisstoredintheslotlocatedinthe

backcorneroftheplastictop,orinsideadrawer(depend- ingonyourunit).

• To lock the drawers, insert the top end of the lock bar through the slot in the top of the unit and over the staple on the base (or depending on your unit, you may need to insert the top end of the lock bar above the top drawer

and then over the staple on the base).

• To secure, lock with a padlock. (Padlock not included.)

• To unlock the drawers, reverse this procedure.

Lock Bar

Fit into slot on the bottom side

sheet

metal top

Lever Style - Lift or lower (depending on the slide) the release lever on both sides, (this allows the slides to ride

over the stops.) Pull out to remove.

Friction Style - Fully extend the drawer. Insert screw-

driver into the slot in the side and push in on the stop

until it clears the lance. Pull drawer just past lance before releasing stop. Repeat the process for the other slide.

REMOVING DRAWERS

• Empty the drawer.

• Fully extend the drawer.

Release

+ 8 hidden pages