Craftsman 706385580, 706385590, 706824452, 706824272, 706824240 Owner’s Manual
OPERATOR'S MANUAL
CRRFTSMRN°
i PROFESSIONAL i
PROFESSIONAL SERIES CANOPY
Caution" Read and follow all Safety Rules and Operating Instructions before first use of this
product. Retain this document for future reference.
Distributed by Sears Brands Management Corporation., Hoffman Estates, IL 60179
F1677
Use appropriate safety equipment when using power and hand tools. Failure to do so may cause personal injury or
product damage.
Use adequate manpower when assembling and moving this unit. Failure to do so may cause personal injury or
product damage.
DO NOT stand on this product. You may fall which may cause personal injury.
DO NOT mount this product on a truck bed or any other moving object. This may cause personal injury or
product damage.
Appropriately secure this product before moving it with a forklift.
DO NOT alter this product in any manner. For example, do not weld external lockbars or attach electrical
AFETY WARNINGS AND CAUTIONS:
equipment. This may cause product damage or personal injury.
Keep the product on level surfaces. The product may become unstable and tip if stored or moved on an un-level
surface, Which may cause personal injury or product damage.
DO NOT step on the shelves. You may fall which may cause personal injury.
TOOLS REQUIRED:
Socket Wrench Screwdriver, Torx Drill
5/16" Socket Screwdriver, Crosstip 1/2" Drill bit
3/8" Socket Hammer Tape Measure
1/2" Socket Center Punch
Hardware Included
1/4-20 X 5/8
Carriage bolt
14-10 X 5/8
Hex washer BB (4)
screw
1/4-20 X 7/16
Hex washer CC (8)
screw S-_
(20)
Bushing
Grommet
MM (2)
NN (2)
(
#8-32 X ½ Torx DE) (4) Grommet "
Self tapping screw ,,:!,,, _,, OO (4)
#6-32 X 1/2 ......
Pan head screw EE (2)
5/16
Washer
1/4-20 GG (24)
Flange nut
#6-32
Hex nut HH (4)
Plastic rivet KK (11) screw
FF (24)
Long hinge pin PP (2)
Short hinge pin
14-10 X 1-1/2
Hex washer
RR (2)
SS (7)
End cap
LL (2) Carriage bolt
1/4-20 X 2-1/4
Call 1-800-4MY-HOME (1-800-469-4663) for Service Parts.
efer to Service Parts Drawing for full listing of Service Parts.
JJ (4)
C
B
E
A
G
H
fSTEP 1 :
_STEP 2: _'_
/ sf" "\
AA (15) FF (15) GG (15)
Assemble back (B) to left side (A) and right side (D) using (4)
bolts (AA), (4) washers (FF), and (4) nuts (GG) in each side.
Front
Back
"a
• Attach top (C) to unit using (7) bolts (AA), (7) washers (FF),
and (7) nuts (GG).
• Square the unit and wrench tighten all fasteners.
AA (5) FF (9) GG (9)
JJ (4)
Note: Finger tighten all fasteners until instructed to wrench
tighten.
• Assemble top panel (E) and front panel (F) using (5) bolts
(AA), (5) washers (FF) and (5) nuts (GG).
• The top panel (E) should be outside of the front panel (F).
• Install (4) corner braces (J) using (2) bolts (TT), (2) washers
(FF), and (2) nuts (GG)in each set.
• Square the unit and wrench tighten all fasteners.
R
AA
Front
..... FF
GG
E
Top
AA .... T C
'j \\
GG
Front
_llll
©
i
i ....
J
_'STEP 3:
MM (2) BB (2)
PP (2)
Snap shaft ends of struts (J) over ball studs on canopy sides
as shown.
fSTEP 4: "_
• Install (2) grommets (NN)in outside holes of stiffeners on
lower door (G).
• Mount lock (I) to door (G) as shown, using mounting nut. The
access notch on the lock should be toward the top of the
door.
• Insert the key and rotate the lock 90 ° CCW to the lock
position.
• Insert one end of the lock rod (M) through a stiffener and
through grommet (NN) as shown.
• Repeat for the other end of the lock rod (M).
• Attach lock rod (M) to the lock (I) using adaptor nut as
shown.
• Because lock is in "Lock" position, rotate lock CW 180° to
"Unlock."
• Return the key to the middle position and remove key.
//
/
/
d
Ball stud
• Install (2) bushings (MM) in square in sides of unit as
shown.
• Attach door assembly to unit using (2) long pivot pins (PP)
and (2) screws (BB).
• Wrench tighten screws (BB). Do not overtighten.
Note: The ball studs for the door assembly are located on the
outside of the stiffener on the door, near the hinge pins.
• Snap piston end of struts over ball studs on the door
assembly.
PP
NN
Top
Access Notch
toward t_
-- _............ _,_^'4a_÷or
/'
/ Supplied with lock
/
/'
\\\\\\\\
MASTER LOCK ®
ONE-KEY TMLOCK
nut
Mounting nut
supplied with lock
M
quare
hole
Door
assembly
Ball stud
_11111 J
/
/
/
f
_"\\\\\\\\
\\ //
\\\ ///
J
Loading...