Craftsman 706380960 Owner’s Manual

OPERATOR'S MANUAL

CRRFr HRH °

2-DRAWER BB - MIDDLE CHEST

\\

\\\\\\

\

CALL 1-800-4MY=HOME OR (1=800-469=4663) FOR SERVICE
PARTS. Refer to Service Parts Drawing for full listing of Service

Parts.
LOCATING MODEL # iNFORMATiON

Model numbers and other information required for service parts is
located on a label on the interior right side of the top most drawer.

• The maximum weight for each drawer should be no more than
30 pounds.

• Empty weight of the unit is 33 Ibs.

• The maximum product weight, including contents, should be no
more than 125 pounds.

• Lubricate the slides with grease or equivalent, (twice yearly.)

• Lubricate lock with graphite, (yearly).

• Periodically the drawer fronts, drawer trim, and other surfaces
should be cleaned with a mild detergent and water.

• Auto wax will preserve the unit's luster finish. Apply the wax as

to a car. The wax will also help protect the unit against scratch-

es.

• Grease and oil can be removed with most standard cleaning

fluids. For safety, use a nonflammable cleaning fluid.

• If drawer liners are supplied, it is recommended they are used

to protect the finish inside the drawers and to make the drawers

easier to clean. The drawer liners may be cleaned with soap and
water.

DANGER ,_ is used to indicate a hazardous situation which,
if not avoided, wil__!lresult in serious injury or death.

WARNING /ix indicates a hazardous situation which, if not
avoided, could result in serious injury or death.

CAUTIONis used to indicate a hazardous situation which, if not
avoided, _ result in minor injury, moderate injury, or property

damage.
CAUTION: Read and follow all Safety Rules and Operating

Instructions before first use of this product.
DANGER A,

• DO NOT stand on this product. You may fall or cause product to
tip.

• DO NOT open more than one drawer. The product may become

unstable and tip.

• DO NOT step in the drawers. You may fall or cause product to
tip.

• DO NOT mount this product on a truck bed or any other moving
object.

• DO NOT move the product prior to closing and locking all the
drawers. The drawers could come open and make the product

unstable and tip.

WARNING z_

• WEAR SAFETY GLASSES when removing or repositioning the
slides.

• DO NOT pull this product when moving it. Push the product to

prevent personal injury.

• USE THE BRAKES when not moving this product. This will

prevent the product from rolling.

• DO NOT alter this product in any manner. For example, do not
weld external Iockbars or attach electrical equipment.

• Keep the product on level surfaces. The product may become

unstable and tip if stored or moved on an uneven surface.

• BE CAREFUL when closing the cover. Remove hands before
the cover closes completely.

CAUTION

This product is not designed to be directly lifted with a fork lift, or
to be towed with any mechanical devices.

• The maximum weight for each drawer should never be exceed-
ed.

• Only transport this product empty. Properly secure when trans-

porting.

• DO NOT exceed maximum product weight, including contents.

See Operations Sections: Capacities for more information.

Ball bearing slides

Distributed by Sears Brands Management Corporation, Hoffman Estates, IL 60179 Rev C F1818

Tools Required:
3/8 inch wrench
5!16=inch dritt bit

HARDWARE INCLUDED:

1/4 =20 x 5/8-in (Qty: 4)

1/4 =20 Nut (Qty: 4)

0" _± O

NOTE: Not att operation instructions wilt relate to your model.

TO LOCK INTERMEDIATE CHEST
The Iockbar for the intermediate chest is stored in the

top drawer.

Process:

[}Insert the lockbar into the slot in the base.
[}Move the tockbar toward the unit until the bent end fits

into the slot near the lock.

[}Lock with the key.

TO UNLOCK INTERMEDIATE CHEST
[}Reverse above procedure.

REMOVING DRAWERS

- Empty the drawer.
Fully extend the drawer.

intermediate Chest:
Literature

Hardware bag

_, V, t,

TO ATTACH CHEST

Process:

Remove enough drawers to access the top and bottom
mounting surfaces of the units. Refer to drawer removal
instructions.

Place the chest in the desired location on top of the
cabinet and mark the mounting hole locations onto the
cabinet top.

Remove the chest and drill two 5/16" (8mm) holes
through the top of the cabinet.
Secure the units together using (2) 1/4 - 20 x 5/8" screw
and (2) 1/4 - 20 nut at each joint. The hardware is pro-
vided in the bag located with the unit.

Release

Lever Style =Lift or lower (depending on the slide) the
release lever on both sides, (this allows the slides to ride
over the stops.) Putt out to remove.