Craftsman 706335110 Owner’s Manual

OPERATOR'S MANUAL

RRFr$MRN

53-in 8 DRAWER BB WORKSTATION

MODEL # 33511

I_ ..............

• Periodically the drawer fronts, drawer trim, and other surfaces
should be cleaned with a mild detergent and water.

• Auto wax will preserve the unit's luster finish. Apply the wax
as to a car. The wax will also help protect the unit against
scratches.

• Grease and oil can be removed with most standard
cleaning fluids. For safety, use a nonflammable cleaning fluid.

• If drawer liners are supplied, it is recommended they are used

to protect the finish inside the drawers and to make the drawers

easier to clean. The drawer liners may be cleaned

with soap and water.

DANGER ,_ is used to indicate a hazardous situation which,
if not avoided, will result in serious injury or death.

WARNING ,4X indicates a hazardous situation which,
if not avoided, could result in serious injury or death.
CAUTION is used to indicate a hazardous situation which, if not
avoided, _ result in minor injury, moderate injury, or property
damage.

CAUTION: Read and follow all Safety Rules and Operating
Instructions before first use of this product.

CALL 1-800-833-4405 FOR SERVICE PARTS. Refer to Service
Parts Drawing for full listingof Service Parts. Please have model

number ready at time of call.
LOCATING MODEL # iNFORMATiON

Model numbers and other information required for service parts is
located on a label on the interior right side of the top most drawer.

• The maximum weight for each drawer should be no more than
25 Ibs.

• Empty weight of the unit is 166 Ibs.

• The maximum product weight, including contents, should be no

more than 500 Ibs.

• For casters, use high quality bearing grease, (yearly).

• Lubricate the slides with grease or equivalent,(twice yearly.)

• Lubricate lock with graphite, (yearly).

DANGER

• DO NOT

tip.

• DO NOT
unstable

• DO NOT
tip.

• DO NOT
o_e_.

• DO NOT
drawe_.
unstable

WARNING Z_

• WEAR SAFETY GLASSES when removing or repositioning

the slides.

• DO NOT pull the unit, push it when moving

• USE THE BRAKES when not moving this product. This will

prevent the product from rolling.

• DO NOT alter this product in any manner. For example, do not

weld external Iockbars or attach electrical equipment.

• Keep the product on level surfaces. The product may become

unstable and tip if stored or moved on an uneven surface.

• BE CAREFUL when closing the cover. Remove hands before

the cover closes completely.

CAUTION

• This product is not designed to be directly lifted with a fork lift, or

to be towed with any mechanical devices.

• The maximum weight for each drawer should never be exceeded.

• Only transport this product empty. Properly secure when

transporting.

• DO NOT exceed maximum product weight, including contents.

See Capacities for more information.

A

stand on this product. You may fall or cause product to

open more than one drawer. The product may become
and tip.

step in the drawers. You may fall or cause product to

mount this product on a truck bedor any other moving

move the product prior to closing and locking all the
The drawers could come open and make the product

and tip.

Distributed by Sears Brands Management Corporation, Hoffman Estates, IL 60179 F1891

TOOLS REQUIRED:

3/8-in wrench

HARDWARE INCLUDED:

1/4 - 20 x 5/8-in (Qty: 16)

1/4- 20 Nut (Qty: 16)

NOTE: Not all assembly instructions will relate to your model.

CASTER iNSTALLATiON
items Needed:

1/4 - 20 x 5/8-in (Qty: 16)
1/4 - 20 Nut (Qty: 16)

3/8-in Wrench

Process:

• Remove bottom drawers. (See Operation Section, Part

A.)

• Lay the cabinet on its back. Use packaging material to
protect the finish.

• Mount both swivel casters on the same side of the unit.

• Attach the casters using four screws and nuts per caster.

• Wrench tighten all screws. It is recommended not to
exceed 80 inch pounds of torque.

• Return the unit to its upright position.

• Reinstall bottom drawers. (See Operation Section, Part

B.)

Cabinet:

Literature
Caster pack

Screw

REMOVING DRAWERS

• Empty the drawer.

• Fully extend the drawer.

Release

Caster pack

Lever Style - Lift or lower (depending on the slide) the
release lever on both sides, (this allows the slides to ride

over the stops.) Pull out to remove.

iNSTALLING DRAWERS

Ball bearing slide - Pull slides and slide carrier out to fully
extended position (see illustration.) Hold the slide on the
cabinet while aligning itwith the slide on drawer. Slightly
insert one side and repeat for the other side. Slowly push

drawer to its fully closed position to engage slide. Open
drawer and reclose to ensure proper operation.

REMOVING AND iNSTALLiNG SLIDES

To remove the slide from the unit, first remove the
drawer.

• After removing the drawers drill out the rivets, use a
5/32-in drill bit. The rivets will need to be replaced.

• To reinstall the slide, place the slide in the appropriate
position in the unit and pull toward the front of the unit.
Replace rivets to secure slide to the unit.

• For smooth operation, make sure the drawers are
matched with their original slides.

\

\

\

\

\\\\\\

\ Y

slide carrier

slide

_ OCKING THE UNIT

Cabinets:

/

• For units with a lock, insert the locking bar into the slot
in the center of the base. Move the locking bar toward

the unit until the other end fits into the slot in the top next
to the lock. Lock with the key.

• To unlock, reverse the procedure.

• Remove key.

kLj L