Craftsman 706335090 Owner’s Manual

OPERATOR'S MANUAL

RnrrsMRN

4-DRAWER BB BOTTOM CHEST

MODEL # 33509

CALL 1-800=833=4405 FOR SERVICE PARTS. Refer to Service
Parts Drawing for full listingof Service Parts. Please have the

model number ready at time of call.

LOCATING MODEL # iNFORMATiON
Model numbers and other information required for service parts is

located on a label on the interior right side of the top most drawer.

• The maximum weight for each drawer should be no more than
25 pounds.

- Empty weight of the unit is 67 Ibs

• The maximum product weight, including contents, should be no

more than 300 pounds.

• For casters, use high quality bearing grease, (yearly).

• Lubricate the slides with grease or equivalent,(twice yearly.)

• Lubricate lock with graphite, (yearly).

• Periodically the drawer fronts, drawer trim, and other surfaces
should be cleaned with a mild detergent and water.

• Auto wax will preserve the unit's luster finish. Apply the wax as to

a car. The wax will also help protect the unit against scratches.

• Grease and oil can be removed with most standard cleaning

fluids. For safety, use a nonflammable cleaning fluid.

• If drawer liners are supplied, it is recommended they are used

to protect the finish inside the drawers and to make the drawers

easier to clean. The drawer liners may be cleaned with soap and

water.

DANGER _ is used to indicate a hazardous situation which,
if not avoided, will result in serious injury or death.

WARNING Z_ indicates a hazardous situation which, if not
avoided, could result in serious injury or death.
CAUTIONis used to indicate a hazardous situation which, if not
avoided, mAY result in minor injury, moderate injury, or property
damage.

CAUTION: Read and follow all Safety Rules and Operating
Instructions before first use of this product.

DANGER ,A

• DO NOT stand on this product. You may fall or cause product to

tip.

• DO NOT open more than one drawer. The product may become
unstable and tip.

° DO NOT step in the drawers. You may fall or cause product to

tip.

° DO NOT mount this product on a truck bed or any other moving

object.

° DO NOT move the product prior to closing and locking all the

drawers. The drawers could come open and make the product
unstable and tip.

WARNING z_

• WEAR SAFETY GLASSES when removing or repositioning the
slides.

° DO NOT pull this product when moving it. Push the product to

prevent personal injury.

° USE THE BRAKES when not moving this product. This will

prevent the product from rolling.

° DO NOT alter this product in any manner. For example, do not

weld external Iockbars or attach electrical equipment.

° Keep the product on level surfaces. The product may become

unstable and tip if stored or moved on an uneven surface.

° BE CAREFUL when closing the cover. Remove hands before

the cover closes completely.

CAUTION

• This product is not designed to be directly lifted with a fork lift, or

to be towed with any mechanical devices.

° The maximum weight for each drawer should never be exceed-

ed.

° Only transport this product empty. Properly secure when trans-

porting.

° DO NOT exceed maximum product weight, including contents.

See Operations Sections: Capacities for more information.

Distributed by Sears Brands Management Corporation, Hoffman Estates, IL 60179 F1885

TOOLS REQUIRED:
3/8" wrench

Hardware Included:

1/4 - 20 x 5/8 Screw (Qty: 16)

1/4 - 20 Nut (Qty: 16)

CASTER iNSTALLATiON
items Needed:
1/4 - 20 x 5/8" (Qty: 16)

1/4 - 20 Nut (Qty: 16)
Screwdriver

3/8-in Wrench

Process:

• Remove bottom drawers. (See Operation Section, Part

B.)

• Lay the cabinet on its back. Use packaging material to
protect the finish.

•Attach the casters using (4) 1/4 - 20 x 5/8" screws and
(4) 1/4 - 20 nuts per caster.

• Wrench tighten all screws. It is recommended not to
exceed 80 inch pounds of torque.

• Return the unit to its upright position.

• Reinstall bottom drawers. (See Operation Section, Part
C.)

Cabinet:
Literature

Hardware bag
Caster pack

Caster pack

\

\

\

Screw

NOTE: Not all operation instructions will relate to

your model.

THE LOCKBAR FOR THE ROLL-AWAY IS STORED IN A
SLOT iN THE TOP FRONT CORNER OF THE UNIT.

TO LOCK ROLL=AWAY

Process:

- insert the straight end of the Iockbar into the slot in the

base.

- Move the Iockbar toward the unit until the bent end fits

into the slot near the lock.

- Lock with the key.

NOTE: If your unit is equipped with a storage compartment

with a panel at the bottom, pull panel out, lift up and push
panel back into unit to gain access to compartment.

REMOVINGDRAWERS

• Empty the drawer.

• Fully extend the drawer.

Lever Style - Lift or lower (depending on the slide) the
release lever on both sides, (this allows the slides to ride

over the stops.) Pull out to remove.

Release

INSTALLING DRAWERS
Ball bearing slide - Pull slides and slide carrier out to fully

extended position (see illustration.) Hold the slide on the
cabinet while aligning it with the slide on drawer. Slightly

insert one side and repeat for the other side. Slowly push
drawer to its fully closed position to engage slide. Open
drawer and reclose to ensure proper operation.

slidecarder

/

slide

REMOVING AND INSTALLING SLIDES

To remove the slide from the unit, first remove the
drawer.

• After removing the drawers drill out the rivets, use a 5/32-
in drill bit. The rivets will need to be replaced.

• To reinstall the slide, place the slide in the appropriate

position in the unit and pull toward the front of the unit.
Replace rivets to secure slide to the unit.

• For smooth operation, make sure the drawers are

matched with their original slides.

Ddll out rivet

J

/