Craftsman 706333940 Owner’s Manual

OPERATOR'S MANUAL

3-DRAWER BB BOTTOM CHEST

MODEL # 33394

CALL 1-800=833=4405 FOR SERVICE PARTS. Refer to Service
Parts Drawing for full listing of Service Parts. Please have the

model number ready at time of call.
LOCATING MODEL # iNFORMATiON

Model numbers and other information required for service parts is
located on a label on the interior right side of the top most drawer.

• The maximum weight for each drawer should be no more than
25 pounds.

- Empty weight of the unit is 70 Ibs

• The maximum product weight, including contents, should be no
more than 300 pounds.

• For casters, use high quality bearing grease, (yearly).

• Lubricate the slides with grease or equivalent,(twice yearly.)

• Periodically the drawer fronts, drawer trim, and other surfaces
should be cleaned with a mild detergent and water.

• Auto wax will preserve the unit's luster finish. Apply the wax as to

a car. The wax will also help protect the unit against scratches.

• Grease and oil can be removed with most standard cleaning

fluids. For safety, use a nonflammable cleaning fluid.

• If drawer liners are supplied, it is recommended they are used

to protect the finish inside the drawers and to make the drawers

easier to clean. The drawer liners may be cleaned with soap and

water.

DANGER _, is used to indicate a hazardous situation which,
if not avoided, will result in serious injury or death.

WARNING /iX indicates a hazardous situation which, if not

avoided, could result in serious injury or death.
CAUTIONis used to indicate a hazardous situation which, if not
avoided, m_m_&v_result in minor injury, moderate injury, or property

damage.
CAUTION: Read and follow all Safety Rules and Operating

instructions before first use of this product.

DANGER ,_,

• DO NOT stand on this product. You may fall or cause product to
tip.

• DO NOT open more than one drawer. The product may become

unstable and tip.

• DO NOT step in the drawers. You may fall or cause product to
tip.

• DO NOT mount this product on a truck bed or any other moving
object.

• DO NOT move the product prior to closing and locking all the
drawers. The drawers could come open and make the product

unstable and tip.

WARNING Z_

• WEAR SAFETY GLASSES when removing or repositioning the
slides.

• DO NOT pull this product when moving it. Push the product to

prevent personal injury.

• USE THE BRAKES when not moving this product. This will

prevent the product from roiling.

• DO NOT alter this product in any manner. For example, do not
weld external Iockbars or attach electrical equipment.

• Keep the product on level surfaces. The product may become

unstable and tip if stored or moved on an uneven surface.

• BE CAREFUL when closing the cover. Remove hands before
the cover closes completely.

CAUTION

• This product is not designed to be directly lifted with a fork lift, or
to be towed with any mechanical devices.

• The maximum weight for each drawer should never be exceed-

ed.

• Only transport this product empty. Properly secure when trans-

porting.

• DO NOT exceed maximum product weight, including contents.

• Lubricate lock with graphite, (yearly).

Distributed by Sears Brands Management Corporation, Hoffman Estates, IL 60179 F1890

See Operations Sections: Capacities for more information.

TOOLS REQUIRED:
3/8" wrench

Ftat-tip Screwdriver

Hardware Included:

1/4-20 Hex Nut (Qty: 16)

1/4-20 x A38-in HW Screw (Qty: 16)

CASTER INSTALLATION

@

Items Needed:
1/4 =20 x A38" (Qty: 16)

1/4 =20 Nut (Qty: 16)
Screwdriver

3/8=in Wrench

Process:

- Remove bottom drawers. (See Operation Section, Part
B.)

- Lay the cabinet on its back. Use packaging materiat to
protect the finish.

oMount both swivel casters on the same side of the unit as

the side handle.

-Attach the casters using (4) 1/4 - 20 x 518" screws and (4)
1/4 - 20 nuts per caster.

oWrench tighten all screws, it is recommended not to

exceed 80 inch pounds of torque.

oReturn the unit to its upright position.

- Reinstall bottom drawers. (See Operation Section, Part

C.)

Nut ......

Chest:

Literature
Hardware bag

Caster pack

Caster pack

\

\

\

Screw

NOTE: Not all operation instructions witt relate to your

model.

O THE LOCKBAR FOR THE ROLL-AWAY iS STORED iN A

SLOT iN THE TOP FRONT CORNER OF THE UNIT.

TO LOCK ROLL-AWAY

Process:

oinsert the straight end of the tockbar into the slot in the

base.

oMove the tockbar toward the unit until the bent end fits

into the slot near the lock.

oLock with the key.

TO UNLOCK ROLL-AWAY CABINET
oReverse above procedure.

NOTE: If your unit is equipped with a storage compartment
with a panel at the bottom, pull panel out, lift up and push
panel back into unit to gain access to compartment.

REMOVINGDRAWERS
oEmptythedrawer.

Fullyextendthedrawer.

Release

Lever Style = Lift or lower (depending on the slide) the
release lever on both sides, (this allows the slides to ride

over the stops.) Putt out to remove.

REMOVING AND iNSTALLiNG SLIDES

®

. To remove the slide from the unit, first remove the

drawer.

oAfter removing the drawers drill out the rivets, use a 5132-

in dritt bit. The rivets witl need to be replaced.

oTo reinstall the slide, place the slide in the appropriate

position in the unit and putt toward the front of the unit.

Replace rivets to secure slide to the unit.

oFor smooth operation, make sure the drawers are

matched with their originat slides.

\

/

iNSTALLiNG BRAWERS
BaH bearing shale = Putt slides and slide carrier out to fully

extended position (see illustration.) Hotd the slide on the
cabinet while aligning it with the slide on drawer. Slightly

insert one side and repeat for the other side. Slowly push
drawer to itsfutty closed position to engage slide. Open
drawer and rectose to ensure proper operation.

slidecarrier

i

/

REMOVING AND iNSTALLiNG SLIDES FROM UNtT

@

oFirst remove the drawer. (See section A)
To remove the slide:

oPush slide to the ctosed position.
oinsert flat tip screw driver between stide and unit, behind

rear rectangular cutout.(See illustration.)

oRotate screw driver ½ turn to force stide away from unit.
oPush on front of slide pushing it towards back of the unit.

To attach the slide:

- Extend stide and locate lances within respective

cutout in carrier.

- Putt slide forward until slide locks back into place.

oReinstall drawer following drawer installation proce-

dure.(See section B)

\

\,

\