Craftsman 706331480 Owner’s Manual
OPERATOR'S MANUAL
I I:RAFTSM AH°l
Drawer accessory
10133 Red/Black
10139 Black/Platinum
For use with CRAFTSMAN workbench 10132 or 10138
\
\
y
CAUTION: Read and follow all Safety Rules and Operating Instructions before first use of this product.
Retain this document for future reference.
Distributed by Sears Brands Management Corporation., Hoffman Estates, IL 60179 F1703
SAFETY WARNINGS AND CAUTIONS:
• Use appropriate safety equipment when using power and hand tools. Failure to do so may cause personal injury or product |
damage. |
• Use adequate manpower when assembling and moving this unit. Failure to do so may cause personal injury or product |
damage. |
• DO NOT stand on this product. You may fall which may cause personal injury. |
• DO NOT mount this product on a truck bed or any other moving object. This may cause personal injury or product damage.|
• Appropriately secure this product before moving it with a forklift. |
• DO NOT alter this product in any manner. For example, do not weld external Iockbars or attach electrical equipment. This |
may cause product damage or personal injury. |
• Keep the product on level surfaces. The product may become unstable and tip if stored or moved on an un-level surface, |
which may cause personal injury or product damage. |
• BE CAREFUL when opening more than one drawer. The product may become unstable and tip, which may cause )ersonal|
injury or product damage. |
• DO NOT step in the drawers. You may fall which may cause personal injury. |
Maximum weight for each drawer should be no more than (35) pounds. /
Tools Required: Parts Included: Hardware Included:
Socket wrench Label Description Quantity 1/4-20 x 5/8
7/16" socket A Side 1 carriage bolt
11/32" wrench B Rail 1
Screwdriver, crosstip C Drawer (3") 2
Screwdriver, flathead D Drawer (4") 1
Square E Drawer (6") 1
F Drawer (9") 1
G Slide 10
5/16
washer
1/4-20
flange nut
8-32 X 3/8
self tapping screw
G (10)
A _/
/ _ truss head screw
C(2)
J
8-32 X 3/8
8-32
keps nut
Jl
AA(12)
BB(12)
CC(12)
DD(20)
EE(20)
FF(20)
Leveling
foot
Call 1-800-4MY-HOME (1-800-469-4663) for Service Parts.
efer to Service Parts Drawing for full listing of Service Parts.
EE(4)
STEP (1):
f
STEP (2):
AA(10)
_' BB(10)
\\. ..... /
GG(2)
cc(10)
Ensure that the leveling screws on the work bench are
extended to at least (1.5) inch, (38 mm). See operation
section; Leveling foot adjustment.
1,5"
(38 mm)
• Assemble (2) adjustment feet (GG) in side panel (A). Make
sure both leveling feet (GG) are fully retracted into A.
Note: Drawer kit may be installed on left or right side of
workbench. Installation is shown on right side.
• Lean side panel (A) at an angle to fit under the rails on the
workbench.
• Line up the side panel with notches on the top rails of the
workbench. Rotate side panel (A) to the upright position inside
notches.
• Attach side panel (A) using (6) bolts (AA), (6) washers (BB),
and (6) nuts (CC).
• Attach rail (B), as shown, using (4) bolts (AA), (4) washers
(BB), and (4) nuts CC.
• Adjust bench to desired height. (See operation section;
Leveling foot adjustment.)
Workbench Top
removed for clarity
i (A) fits in notch in
._" workbench rail
GG
A
_llllll
3
f
STEP (3):
EE(20)
FF(20)
• Separate slide parts. (See drawer removal instructions.)
eu
Gd
STEP (4):
DD(20)
• Install (10) frame slides (Gu) on workbench frame, as shown,
using (2) (DD)in each (Gu).
Workbench top removed for clarity.
• Attach (2) drawer slides (Gd) to each drawer (C, D, E, and F)
as shown.
• Wrench tighten.
Release
......... FF
EE
/
Drawer
Gd
NOTE: Drawers may be organized in several configurations,
below is the slide positioning for the recommended drawer
configuration.
1
3
=:>
F
R
O
N
T
k.
,J
Loading...