Craftsman 706331460 Owner’s Manual
OPERATOR'S MANUAL
I €RAFTSM AH°l
Floor Cabinet
10134 Red/Black
10140 Black/Platinum
CAUTION: Read and follow all Safety Rules and Operating Instructions before first use of this product.
Retain this document for future reference.
Distributed by Sears Brands Management Corporation., Hoffman Estates, IL 60179 F1702
SAFETY WARNINGS AND CAUTIONS:
r -]
• Use appropriate safety equipment when using power and hand tools. Failure to do so may cause personal injury or product damage. |
• Use adequate manpower when assembling and moving this unit. Failure to do so may cause personal injury or product damage. |
• DO NOT stand on this product. You may fall which may cause personal injury. |
• DO NOT mount this product on a truck bed or any other moving object. This may cause personal injury or product damage, l
• Appropriately secure this product before moving it with a forklift. |
• DO NOT alter this product in any manner. For example, do not weld external Iockbars or attach electrical equipment. This may cause |
product damage or personal injury. |
• Keep the product on level surfaces. The product may become unstable and tip ifstored or moved on an un-level surface, which may |
cause personal injury or product damage. |
• DO NOT step on shelves. You may fall which may cause personal injury. |
• Be sure to secure the Floor Cabinet to a studded or concrete wall. Failure to do so may cause the Floor Cabinet to become unstable and I
tip. This may cause personal injury or product damage. |
• The maximum weight for each shelf should be no more than 50 pounds, evenly distributed. |
The maximum product weight, including contents, should be no more than 250 pounds. |
Tools Required:
Socket wrench 1/4-20 X 5/8
3/8" socket Carriage bolt AA(14)
7/16" deep-well socket
7/16" open end wrench 1/4-20 X 3/4
Square Button Head BB(24)
Screwdriver, Flathead Screw
Screwdriver, Crosstip
Drill #8-32X 3/8
1/8" drill bit Self tapping screw CC(18)
1/4" drill bit
Parts Included:
Label Description Quantity
A Side 2
B Top 1
C Back 2
D Shelf 3
E Door (Left) 1
F Door (Right) 1
G Bottom 1
H Mounting Bracket 1
Hardware Included
5/16 DD(14)
Washer
1/4-20 EE(38)
Flange nut
Slider
Screw
Leveler
J
FF(1)
GG(4)
5/32" Hex key
#14-10 X 3
Hex screw
Call 1-800-4MY-HOME (1-800-469-4663) for Service Parts.
efer to Service Parts Drawing for full listing of Service Parts.
HH(1)
JJ(1)
B
C(2).
A(2)
/
/
H
D(3)
J
/
/
/
,\ j-
G
,J
Use adequate personnel to assemble and move cabinet.
Failure to do so could result in personal injury or product
damage.
_NOTE: While unpacking the cabinet, save packaging materials TM
to use as a scratch free surface.
f
STEP (2):
BB(3)
EE(3)
STEP (1):
BB(4)
EE(4)
For ease of assembly, finger tighten all fasteners until instructed
to wrench tighten in step 7.
• Place (1) side (A) with flange side down. Use packaging
material to prevent scratches.
• Insert (2) screws (BB) into middle (2) holes from bottom of
flange on (A).
• Place (1) back (C) over screws in flange on side (A). Attach
using (2) nuts (EE).
• Repeat the above procedure to assemble remaining side (A)
and back (C).
• Connect (2) back panels together using (3) screws (BB) and
(3) nuts (EE).
_111111
Use middle
(2) holes
Y
Y
A_
EE
\\
C_\\
\\\\\\\\\\\\\
BB
jj .......
\\
\
\
\71
T
BB
EE
,J
f
STEP (3):
AA(4)
BB(8)
DD(4)
EE(12)
• Insert top (B) into one end of cabinet and attach as follows.
• Use (4) bolts (AA), (4) washers (DD) and (4) nuts (EE) in
square holes.
• Use (4) screws (BB), and (4) nuts (EE) in round holes on
sides.
• Use (4) screws (BB), and (4) nuts (EE) in round holes on back.
STEP (4):
cc(2)
FF(1)
Note: Slide wilt need adjustment after doors are installed on the
unit.
• Place (1) shelf (D) with top down. Use packaging material to
prevent scratches.
• Install slider (FF) as shown, using (2) screws (CC).
• Move slider fully to the right and tighten screws. (Do not
overtighten.)
D
/
\
\
/ \\
AA
DD Insquare
..........CC
Use with (AA) holes
/
÷
i
i
i
/ I
/-
I
k.
IT
Iq_\
_.z _ _
/J"
jJ
BB EE
?i
FF
,J
Loading...