Craftsman 706323180 Owner’s Manual

OPERATOR'S MANUAL

T °

6-DRAWER BB TOOL CENTER - MODEL # 32318

CALL 1-800-366-7278 FOR SERVICE PARTS. Refer to Service
Parts Drawing for full listing of Service Parts.

LOCATING MODEL # INFORMATION
Model numbers and other information required for service parts is

located on a label on the interior right side of the top most drawer.

Ball bearing

• Periodically the drawer fronts, drawer trim, and other surfaces
should be cleaned with a mild detergent and water.

• Auto wax will preserve the unit's luster finish. Apply the wax as to
a car. The wax will also help protect the unit against scratches.

• Grease and oil can be removed with most standard cleaning

fluids. For safety, use a nonflammable cleaning fluid.

• If drawer liners are supplied, it is recommended they are used

to protect the finish inside the drawers and to make the drawers

easier to clean. The drawer liners may be cleaned with soap and
water.

DANGER _, is used to indicate a hazardous situation which,
if not avoided, will result in serious injury or death.

WARNING z_ indicates a hazardous situation which, if not
avoided, could result in serious injury or death.

CAUTION is used to indicate a hazardous situation which, if not
avoided, may. result in minor injury, moderate injury, or property

damage.
CAUTION: Read and follow all Safety Rules and Operating

Instructions before first use of this product.
DANGER

• DO NOT
pe_onal

• DO NOT
i_ury.

• USE THE BRAKES when not moving this product. This will pre-
vent the product from rolling, which may cause personal injury or

product damage.

• APPROPRIATELY SECURE this product before moving with a
forklift.

• DO NOT tow with power equipment. The product could tip, which
may cause personal injury or prduct damage.

A

stand on this product. You may fall, which may cause
injury.

step in drawers. You may fall, which may cause personal

WARNING z_

• The maximum weight for each drawer should be no more than
30 Ibs.

• Empty weight of the unit is: 71 Ibs

• The maximum product weight, including contents, should be no

more than 500 Ibs.

• For casters, use high quality bearing grease, (yearly).

• Lubricate the slides with grease or equivalent,(twice yearly.)

• Lubricate lock with graphite, (yearly).

Sears Brands Management Corporation, Hoffman Estates, IL 60179 USA F1963

• WEAR SAFETY GLASSES when removing or repositioning the
slides. The tool could slip, which may cause personal injury.

• DO NOT mount this product on a truck bed or any other moving
object. This may cause personal injury or product damage.

• DO NOT alter this product in any manner. For example, do not
weld external Iockbars or attach electrical equipment. This may
cause personal injury or product damage.

• UNIT MUST BE located on a level surface. The product may be-
come unstable and tip if stored or moved on an un-level surface,

which may cause personal injury or product damage.

• LOCK the drawers before moving this product. The drawers could
come open and make the product unstable and tip, which may
cause personal injury or product damage.

• DO NOT pull this product when moving it. Push the product to
prevent personal injury.

CAUTION

• BE CAREFUL when opening more than one drawer. The product
may become unstable and tip, which may cause personal injury or
product damage.

& ,$ T

TOOLS REQUIRED:
Flat-tip Screwdriver

3/8-in Wrench

HARDWARE REQUIRED:

1/4-20 Hex Nut (Qty: 16)

1/4-20 x .438-in Screw (Qty: 16)

1/4-14 x 5/8 Sheet Metat Screw

(Qty: 4)

Chest:

Literature

Cabinet:

Literature
Hardware bag

Caster pack

REMOVE CHEST FROM ROLL-AWAY

The unit comes with the chest secured to the inside of
the rotbaway by either two or four 1/4-14 x 5/8 screws.

Lay the rolbaway down on its back. Use packaging
material to protect the paint finish.

Remove the securing screws from the underside of the
roll-away. Save the screws for mounting the chest to the
roll-away.

Remove the chest.

_ CASTER INSTALLATION

Items Needed:

1/4-20 x A38qn Screw (Qty: 16)
1/4-20 Hex Nuts (Qty: 16)

Process:

NOTE: Use adequate manpower for this operation.

- Open the bulk storage panel.
Lay the unit on its back, use packaging material to

protect the paint finish.
Attach the casters to unit using (4) 1/4-20 x .438-in
Screws and (4) 1/4-20 Nuts per caster. Mount both

swivel casters on the same side of the unit. Wrench-
tighten.

Return the unit to its upright position.
Close the bulk storage panel.

Nut

Caster pack

Screw

MOUNTING CHEST

Remove the drawer from the roll-away (refer to the
drawer removal instructions).
Lift the chest onto the rolbaway. Line up the holes in
the bottom of the chest with the holes in the top of the
roll-away.

Attachthechestusingtwo1/4-14x5/8screwsthatwere
usedtosecurethechesttothebottomoftheroll-away.
Wrenchtightenallscrews.

Replacethedrawer(refertothedrawerinstaJtationinstruc-

tions).
Toremovethechest,reversetheprocedure.

LABELS (iF APPLICABLE)

@

PrOCeSS:

- Apply a Jight film of glass cJeaner to the surface where
the label is to be applied.

- PeeJ the JabeJfrom the backing and place the label in
position.

- Check aJignment of the Jabel and adjust accordingly.

- Hold the Jabet in position and squeegee off excess Jiquid
with a towel, working from the center toward each end of

the Jabet.

- Suggested label location is shown.

0 _ _± 0 7

REMOVING DRAWERS

Empty the drawer.
FutJyextend the drawer

_, Release

/

Lever Style - Lift or lower (depending on the slide) the
release lever on both sides, (this allows the stides to ride

over the stops). Putt out to remove.

\\\

\