Craftsman 706182720, 706182500 Owner’s Manual

CHESTS

Please indicate the following
information from the service

part drawing provided.

SAFETY WARNINGS AND CAUTIONS:

• DO NOT stand on this product. You may fall which may cause personal injury.
Stacked products should be bolted together. The products could become unstable

and tip, which may cause personal injury or product damage.

• WEAR SAFETY GLASSES when removing or repositioning the slides. The tool
could slip which may cause personal injury.

• BE CAREFUL when closing the cover. Remove hands before the cover closes
completely to prevent personal injury.

• BE CAREFUL when opening more than one drawer. The product may become
unstable and tip, which may cause personal injury or product damage.

• DO NOT mount this product on a truck bed or any other moving object. This may
cause personal injury or product damage.

• DO NOT step in the drawers. You may fall which may cause personal injury.
Appropriately secure this product before moving it with a forklift.

• WEAR SAFETY GLASSES AND BE CAREFUL when repairing or servicing the
product. The spring loaded parts may cause personal injury.

• Close the cover and lock the drawers and doors before moving this product. The
drawers or doors could come open and make the product unstable and tip, which

may cause personal injury or product damage.

• DO NOT alter this product in any manner. For example, do not weld external
Iockbars or attach electrical equipment. This may cause product damage or

personal injury.

• Use adequate manpower to lift the chest.

• Keep the product on level surfaces. The product may become unstable and tip if
stored or moved on an un-level surface, which may cause personal injury or

product damage.

Model Number:

Model Description:

CAUTION:

Read and follow all Safety Rules and Operating Instructions before first use
of this product. Retain this document for future reference.

Sears, Roebuck and Co., Hoffman Estates, IL60179 USA

A

Call 1-800-366-7278 for Service Parts

Refer to Service Parts Drawing for full listing of Service Parts

F 1849

HARDWARE:

'_ i:'::: 10-24 x 546 Hex Screw

t_}_ ::_::_i:,:] 546-18 x 1 Hex Screw

TO UNLOCK UNIT:

• Pull handle lever out.

• Insert the key into the lock and turn it
clockwise.

• Release lever.

• If the drawers do not open, push all the
drawers completely closed to release
the lockbars.

Lever Style-Lift the release lever on the
right side, while depressing the lever on

the left side, (this allows the slides to
ride over the stops). Pull out to remove.
Tab Style-Depress the release tab on
both sides, (this allows the slides to
ride over the stops). Pull out to remove.

Release
Left

CHEST AND INTERMEDIATE
CHEST ATTACHMENT:
NOTE: Use adequate manpower to lift

the chest in this operation.

• Remove the top two drawers of the cart
(refer to the drawer removal

instructions).

• Lift the chest onto the cart. Line up the
holes in the bottom of the chest with the

holes in the top of the cart.

• Remove the wooden top from the cart
before mounting the chest.

• Attach the chest using four 5/16-18 x 1
hex screws inserted from the underside

of the top of the cart.

• Wrench tighten all screws.

• Replace the drawers (refer to drawer
installation instructions).

• To remove, reverse procedure.

DIVIDER INSTALLATION:
NOTE: Before installing the dividers in

the drawers, decide which position and
in which drawers they would best serve
your needs.

Dividers ....._, " / Drawer

///

10-24 x 546

• The dividers are cut-to litright to left in
the drawers. If you prefer to run them
front to back, they may be trimmed in
length to do so.

• Position the dividers in the desired
locations.

• Thread the #10-24 x 5/16 hex screws
through the bottom of the drawer and

into each divider. Tighten all the screws.

DRAWER LINER:

• Remove the non-slip drawer liner from
the roll. The drawer liner may be cut with
scissors to fit each drawer and around

the drawer dividers, if necessary.

Hex ,£crp-w.

kj

TO LOCK UNIT:

• Always check the unit to make sure all
the drawers are completely closed

before locking.

• Pull the handle lever.

• Insert the key into the lock and turn it
counterclockwise.

• Release Lever.

REMOVING AND INSTALLING
DRAWERS:

NOTE: The drawers in these units can
be rearranged to fit your specific

needs. This means that drawers may
be moved or replaced as desired. For
example, a 6-inch drawer may be
replaced by a 2-inch and a 4-inch
drawer, or three 2-inch drawers.

• Empty the drawer.

• Fully extend the drawer.

Release
Right

• To reinstall, push the drawer into the
slides until the drawer stops.

REMOVING AND INSTALLING
SLIDES:

NOTE: To remove the slide from the
unit, first remove the drawer.

• Lift and hold the spring retainer, and
push the slide toward the rear of the
unit. The slide may now be removed.

• To reinstall the slide, place the slide in
the appropriate position in the unit and
pull toward the front of the unit until the

spring retainer snaps into position and
secures the slide.

• For smooth operation, make sure that
the drawers are matched with their

original slides.

/

/

Spring
Retainer

3 4