Craftsman 706149430 Owner’s Manual

OPERATOR'S MANUAL PART# F1726
BACKWALL WITH METAL PEGBOARD
CAUTION: Backwall MUST be attached to the Workbench before the top is attached.
CAUTION: Read and follow all Safety Rules and Operating Instructions before first use of this product.
Distributed by Sears Brands Management Corporation., Hoffman Estates, IL 60179 F1726
Use appropriate safety equipment when using power and hand tools. Failure to do so may cause personal injury or product damage. Use adequate manpower when assembling and moving this unit. Failure to do so may cause personal injury or product damage.
DO NOT stand on this product. You may fall which may cause personal injury. DO NOT mount this product on a truck bed or any other moving object. This may cause personal injury or product damage.
Appropriately secure this product before moving it with a forklift.
DO NOT tow with power equipment. The product could tip, which may cause personal injury or product damage. DO NOT alter this product in any manner. This may cause product damage or personal injury. Keep the product on level surfaces. The product may become unstable and tip if stored or moved on an un-level surface, which may
cause personal injury or product damage.
Be sure the workbench is flat on the floor before installing the Workbench Backwall. Failure to do so may cause personal injury or product damage.
The maximum weight allowed to hang on or be in any way supported from the backwall is 65 pounds. If the limit is exceeded the product
may tip and cause personal injury or product damage.
AFETYWARN,NGSANDCAUT,ONS'.
Be sure to secure the unit to a studded or concrete wall. Failure to do so may cause the unit to become unstable and tip. This may
cause personal injury or product damage.
Use only the provided pegboard on Workbench Backwall. Backwatl with Metal Pegboard is only to be attached to one of the following Workbenches: 14929, 14928, 14925 and 14940. Failure to
,do so may cause personal injury or product damage.
Tools Required:
Socket Wrench 7/16" Socket 3/8" wrench Drill 3/32" Drill Bit
1/8" Drill Bit Screwdriver, Crosstip
Screwdriver, Flathead Hammer
_ii_ AA (20) _ FF(6) LL(2)
J
Hardware Included:
BB(20) i}_ GG(2) _ MM(4)
NN(2)
CC(20) HH(5)
DD(6) _ JJ(2)
PP(2)
EE(6) J_ KK(2)
all 1-800-4MY-HOME (1-800-469-4663) for Service Parts. Refer to Service Parts Drawing for full listing of Service Parts.
RR(2)
,J
jJ
j-
.J
©
\\\
\\\
,J
f
WARNING: Backwall with Metal Pegboard is only to be attached to one of the following Workbenches: 14929, 14928, 14925 and
14940.
TOP REMOVAL:
Remove and reuse fasteners from wood top.
Remove top from workbench base.
cc AA
D
BB
STEP 1 :
Remove and reuse the top and bottom fasteners from the top back of the workbench.
Attach (2) A to workbench, as shown, using existing hardware (8) AA, (8) BB and (8) CC.
Finger tighten.
Flange pointed back
A
Existing Hardware
CC
\
\\
E C
*Note: Part E is symmetrical and can be used on either side.
STEP 3:
MM(4)
Install (4) MM in flanges of C and D.
STEP 2:
AA(8)
BB(8)
cc(8)
\. _j_
Attach (1) C and (1 D to (2) E and (2) A, as shown, using (8) AA, (8) BB and (8) CC.
Finger tighten.
Wrench tighten fasteners from step 1.
Fasteners
from step 1
/
ii /
/
J
f
STEP 4:
HH(1) (8'ONLY) KK(2)
LL(2)
Assemble (2) LL and (2) JJ loosely together.
Place hardware assembly into top slots in light housing F.
Tighten so each JJ locks LL into place.
Attach light assembly into B and secure with (2) KK.
On the 8' Workbench insert (1) HH into hole of B to protect light cord.
STEP 5:
DD(6)
EE(6)
RR(2)
CC(4)
Attach light assembly B to Backwall using (4) AA, (4) BB, (4) CC, (6) DD, and (6) EE as shown.
DD
\4
\\
KK
LL
AA
EE _ _ EE
DD _'\CC
BB Back of workbench
Use (2) RR where appropriate to support the light wire.
/
/
(Not used on 6'
Workbench)
HH
\\,
B
\
\
\
\
/
\\\
F
_11111,
Loading...
+ 11 hidden pages