Craftsman 706139910 Owner’s Manual

Owner's Manual

STATIONARY STOOGE

UNIT

Stationary Storage Unit

Stationary Storage Unit Ii

WARNINGS AND CAUTIONS:

- DO NOT stud on this product You may fail which may cause personal injury,

• WEAR SAFETY GLASSES AND GLOVES when cutting the banding material, The bands may snap which may cause personal injury.

. BE CAREFUL when opening more than one drawer, The product may become

uns_ble and tip, which may cause personal injury or product damage, DO NOT mount this product on a truck bed or any other moving object This may

cause personal injury or product damage, DO NOT step in the dra'_rs. You may fall which n_y _use personal injury,

. Appropriately _ure this product before moving it _th a forklift, . DO NOT alter this product in any manner, For example, do not weld external Iockbars

or attach electfica_ equipment, This may cause product damage or personal inju_. Ciose the drovers and doors before moving this product, The dr_rs or doors could come open and make the product unstable and tip, which may cause personal injury or product damage.

. The maximum weight for each drawer should be no more than 50 pounds. . Weight limit an the top of the workbench is t,00O pounds, if the limit is exc_ the

product could collapse and cause _rsonal injury or product damage.

r ..... ii, ;......... _......... ........ ........ • ..................... .... ...................... ...............................

CaUi 1o800-366-7278 for Service Parts

PARTS:

STATIO_R¥ STOOGE UNIT

KEY DESCRIPTION qTY.

A SiDE 2

B CENTER SUPPORT 4 C 9" D_WER ASSY, 2

D 4" DRAWER ASSY, 9 E 2" DRAWER ASSY 2 F F4AE_, 6

G SHELF 2

H TOP 1

Refer to Service Parts Drawing for fu!l listing

of Service Parts

CAUTION:

Read and follow all Safety Rules and Operating

instructions before first use

of this product.

Sears, Roebuck and Co., Hoffman Estates, IL 60179 USA

Made in the U,S,A.

Fg07A1

NOTE: Slides wot shown.

STATIONARY STORAGE UNIT II

KEY DESCRIPTION QTY,

A SiDE 2

B CENTER SUPPORT 2 C 9" DRAWER ASSY. 1 D 4" DRAWER ASSY 2 E 2" D_WER ASSY. 2 F R4IL 4

G SHELF 2 t{ _TOP t

NOTE: Varies slightly from

picture. Slides and door not shown.

A -\.

HARDWARE:

(Hard.re depe_ant on model)

_} _ 1'4-20 X t/2 Slei_ed Screw

6) @_,_ "/4_,20X V2 Tamper Proof Screw

Slotted

iqole

SLIDE ASSEMBLY: NOTE: These units are designed so that

the drawers and shelves may be positioned to suit your needs. During installation of" the slides, start at either

the top or the bottom oftl_ unit a_ work to_rd the other end.

D_WER INSTALLATION:

Before instaJling the drawers, lubricate the top and bottom channels of the

drawer slides,

O _ _,_2_x 7,,I_He×screw

These instructions pertain to two units. Most of the steps relate to both units;

however, the specific unit will _ called out if the assembly belongs only to iL

RAIL AND CENTER SUPPORT ASSEMBLY:

STATIO_Y STORAGE UNIT: This unit has six rails and four _nter suppers. Attach the center supports (B) to

the center of the rails (F) using sixt_n 1/4- 20 x 7/16 hex screws and sixteen 1/4_20

hex nuts, Finger tighten.

SIo[[ed"f_''":_- ._

21--_

Slot

bole

STATIONARY STORAGE UNIT I1:

This unit has four rails and tv_ center

supped& Make sure that the slots in the top rail are on top and the slots in the bottom rail are dove, and that the word "Top" on

the center supports is toward the top, Attach the center supports (B) to the rails (F) using two 1/4-20 x 7/16 hex screv_ and

t/4-20 hex nuts per joint Finger

tighten.

Hole

SIDE ASSEMBLY: _TE: Do not insert screws in the top

holes of t_ side and rail assemblies until the top is in place.

- Attach the rail and center support assembly to the side using one 1/4_20 x 7/16 hex screw and one 1/4-20 nut per

comer at the top joints, Attach the bottom

joints with two 1/4-20 x 7/16 hex ssrevcs and nuts. _TE: For Stationary Storage Unit attach the middle rails to

each side _th _ 1/4-20 x 7/16 hex screws and nuts per joint, Finger

tighten.

The open areas between the center supports (B) and sides (A) must

measure 18 1/2" for proper fit of the drav,_rs, Square up the frame and wench tighten the screws,

• Place the rear of the outside slide at the rear of the unit, line up the holes and

attach the slide with tw'3 1/4-20 x 7/16 hex screws and _ 1/2=20 hex nuts,

Finger tighten, Attach the remaining

slides leaving a gap between them according to the dra_r size.

- Before instaJling the inside slide, lubricate the top and bottom channels of the outside slide.

- Guide the inside slide into the channel at the front end of the outside slide. R_ly

push the inside slide past the slide stop on the outside slide. Repeat this step for

the remaining slides.

TOP ASSEMBLY:

• Place the top (H) on the rail and side assembly; line up the four hobs and

attach the top using four 1/4-20 x 7/16 hex screws and 1/4-20 hex nuts.

i°

/! °

• Wrench tighten all screws and nu_s.

• Move the unit to a permanent location,

. Install the drawer by in_rting the drawer

slides into the instalbd siide assemblbs Make sure that the slides on both sides line up, Push the drav_r until it is fully

close, The dra_,-_r is now securely in place Repeat the procedure for the remaining drawers.

NOTE: Door, lock, and door catch a_mblies are for Stationary Storage

Unit II only.

DOOR ASSEMBLY: NOTE: The door may be mounted on

either side of the unit, CAUTION: O_e the door hinge screws are tightened

they cannot be removed with a screwdriver.

o The door catch, lock, a_ mounting

hard.re is in a _parate bag,

• Remove the knockouts from the front end panel on the side that the d_r is to

be hung, Position the door on the side of the work

bench opening se!ected and line up the holes on the hinge and the bench front,

3 4

+ 1 hidden pages