Craftsman 580767301 Owner’s Manual
Owner's Manual
CRRFTSMRN°
6.5 HORSEPOWER
2400 PSI
2.2 GPM
PRESSUR WASHER
Model No. 580.767301
HOURS: Mon.- Fri. 8 a.m. to 5 p.m. (CT)
CAUTION" Before using this product,
read this manual and follow all Safety
Rules and Operating Instructions.
SEARS, ROEBUCK and CO., Hoffman Estates, IL 60179 U.S.A.
Visit our Craftsman website: www.sears.com/craftsman
Part No. 190239 Draft 1 (12/19/2001)
• Safety
• Assembly
• Operation
• Maintenance
• Parts
• Espahol
WARRANTY ................................... 2
SAFETY RULES .............................. 2-3
ASSEMBLY .................................. 4-6
OPERATION ................................ 7-10
MAINTENANCE ............................ 11-14
SPECIFICATIONS ............................. 11
STORAGE ................................. 15-16
TROUBLESHOOTING .......................... 17
REPLACEMENT PARTS ...................... 18-25
EMISSION CONTROL WARRANTY ................ 26
ESPANOL ................................. 27-43
HOW TO ORDER PARTS ............... BACK PAGE
LIMITED WARRANTY ON CRAFTSMAN PRESSURE WASHER
For one year from the date of purchase, when this Craftsman pressure washer is maintained and operated
according to the instructions in the owner's manual, Sears will repair, free of charge, any defect in material and
workmanship.
If this washer is used for commercial purposes, this warranty applies for only 90 days from the date of purchase.
If this pressure washer is used for rental purposes, this warranty applies for only 30 days after date of purchase.
This warranty does not cover:
• Expendable items such as spark plugs or air filters, which become worn during normal use.
• Repairs necessary because of operator abuse or negligence, including damage resulting from no water being
supplied to pump or failure to maintain the equipment according to the instructions contained in the owner's
manual.
Warranty service is available by returning the pressure washer to the nearest Sears service center or dealer in
the United States.
This warranty gives you specific legal rights and you may also have other rights, which vary from state to state.
Sears, Roebuck and Co., Dept. 817WA, Hoffman Estates, IL 60179
The engine exhaust from this product contains
chemicals known to the State of California to
cause cancer, birth defects, or other
reproductive harm.
CAUTION! When setting up, transporting,
adjusting or making repairs to your pressure
washer, always disconnect the spark plug wire
from the spark plug and place the wire where it
cannot contact spark plug.
DANGER! Engine exhaust gases contain
DEADLY carbon monoxide gas. This dangerous
gas, if breathed in sufficient concentrations, can
cause unconsciousness or even death. Operate
this equipment only in the open air where
adequate ventilation is available.
_ ARNING! Gasoline is highly FLAMMABLE
and its vapors are EXPLOSIVE. Do Not permit
smoking, open flames, sparks or heat in the
vicinity while handling gasoline. Avoid spilling
gasoline on a hot engine. Allow unit to cool
before refueling. Comply with all laws regulating
storage and handling of gasoline.
Read this manual carefully and become familiar
with your pressure washer. Know its applications,
its limitations, and any hazards involved.
• Locate this pressure washer in areas away from
combustible materials, combustible fumes or dust.
• The pressure equipment is designed to be used
with Sears authorized parts ONLY. If you use this
equipment with parts that do not comply with
minimum specifications, the user assumes all risks
and liabilities.
• Somechemicalsordetergentsmaybeharmfulif
inhaledor ingested,causingseverenausea,
faintingor poisoning.Theharmfulelementsmay
causepropertydamageorsevereinjury.
• DoNotallowCHILDRENtooperatethepressure
washeratanytime.
• Operateengineonlyatgovernedspeed.Running
theengineatexcessivespeedsincreasesthe
hazardofpersonalinjury.DoNottamperwithparts
whichmayincreaseordecreasethegoverned
speed.
• DoNotwearlooseclothing,jewelryoranything
thatmaybecaughtinthestarterorotherrotating
parts.
• Beforestartingthepressurewasherincold
weather,checkallpartsoftheequipmentandbe
sureicehasnotformedthere.See"Storage"on
page15forcoldweatherprotection.
• Neveruseaspraygunwhichdoesnothavea
triggerlockortriggerguardin placeandinworking
order.
• Keepthehoseconnectedtomachineorthespray
gunwhilethesystemispressurized.Disconnecting
thehosewhiletheunitispressurizedisdangerous.
• Neveroperateunitswithbrokenor missingparts,
orwithoutprotectivehousingorcovers.
• Checkthefuelsystemforleaksorsignsof
deterioration,suchaschafedorspongyhose,
looseormissingclamps,ordamagedtankorcap.
Correctalldefectsbeforeoperatingthepressure
washer.
• DoNotsprayflammableliquids.
• Usearespiratorormaskwheneverthereisa
chancethatvaporsmaybeinhaled.Readall
instructionswithmasksoyouarecertainthemask
willprovidethenecessaryprotectionagainst
inhalingharmfulvapors.
• Neveraimthespraygunatpeople,animalsor
plants.Thepressurestreamofwaterthatthis
equipmentproducescanpierceskinandits
underlyingtissues,leadingtoseriousinjuryand
possibleamputation.
• Neverallowanypartofthebodytocomein
contactwiththefluidstream.DoNotcomein
contactwithafluidstreamcreatedbyaleakinthe
highpressurehose.
• Alwaysweareyeprotectionwhenyouusethis
equipmentorwhenyouareinthevicinitywhere
theequipmentisinuse.
• Highpressurespraycancausepaintchipsorother
particlesto becomeairborne.
• DoNotoperatethepressurewasherabovethe
ratedpressure.
• Nevermovethemachinebypullingonthehigh
pressurehose.Usethehandleprovidedonthe
unit.
• Alwaysbecertainthespraygun,nozzlesand
accessoriesarecorrectlyattached.
• DoNotsecurethesprayguninthe(open)
position.
• Highpressurespraymaydamagefragileitems
includingglass.DoNotpointspraygunatglass
wheninthejetspraymode.
• Holdthespraygunfirmlyinyourhandbeforeyou
starttheunit.Failuretodosocouldresultinan
injuryfromawhippingspraygun.DoNotleavethe
spraygununattendedwhilethemachineis
running.
• Thecleaningareashouldhaveadequateslopes
anddrainagetoreducethepossibilityofafalldue
toslipperysurfaces.
• Keepwatersprayawayfromelectricwiringorfatal
electricshockmayresult.
• DoNotby-passanysafetydeviceonthis
machine.
• Themufflerandengineheatupduringoperation
andremainhotimmediatelyaftershuttingitdown.
Avoidcontactwithahotmufflerorengineasyou
couldbeseverelyburned.
• Operateandstorethisunitona stablesurface.
• Highpressurehosecandevelopleaksfromwear,
kinking,abuse,etc.Watersprayingfromaleakis
capableofinjectingmaterialintoskin.Inspecthose
eachtimebeforeusingit.Checkallhosesforcuts,
leaks,abrasionsorbulgingofcover,ordamageor
movementofcouplings.Ifanyoftheseconditions
exist,replacehoseimmediately.Neverrepairhigh
pressurehose.Replaceitwithanotherhosethat
exceedsmaximumpressureratingofyourunit.
• Themufflerandaircleanermustbeinstalledandin
goodconditionbeforeoperatingthepressure
washer.Thesecomponentsactassparkarresters
iftheenginebackfires.
IntheStateofCaliforniaasparkarresterisrequired
bylaw(Section4442oftheCaliforniaPublic
ResourcesCode).Otherstatesmayhavesimilarlaws.
Federallawsapplyonfederallands.
NOTE:Ifyouequipthemufflerwithasparkarrester,it
mustbemaintainedineffectiveworkingorder.You
canordera sparkarresterthroughyourauthorized
Searsservicedealer.
,_ THIS IS THE SAFETY ALERT SYMBOL. IT IS USED TO ALERT YOU TO POTENTIAL
PERSONAL INJURY HAZARDS. OBEY ALL SAFETY MESSAGES THAT FOLLOW THIS
SYMBOL TO AVOID POSSIBLE INJURY OR DEATH.
Your pressure washer requires some assembly and is
ready for use only after it has been properly serviced
with the recommended oil and fuel.
If you have any problems with the assembly of
your pressure washer, please call the pressure
washer helpline at 1-800-222-3136.
IMPORTANT: Any attempt to run the engine before it
has been serviced with the recommended oil will result
in an engine failure.
REMOVE PRESSURE WASHER
FROM CARTON
• Open carton and slice two corners opposite guide
handle from top to bottom so the panel can be
folded down flat.
• Remove hose reel box, fillers, and parts bag
shipped with your pressure washer.
• Remove spray gun, nozzle extension and engine
oil from fillers.
• Roll the pressurewasher out the open endofthe carton.
• Check carton for additional loose parts.
CARTON CONTENTS
Check all contents. If any parts are missing or damaged,
call the pressure washer helpline at 1-800-222-3136.
• The main unit
• Hose reel and mounting components
• High pressure hose
• Spray gun
• Nozzle extension with Hi/Lo adjustable nozzle
• Handle
• Engine oil
• Parts bag, which includes:
• Owner's manual
• Nozzle cleaning kit
• O-Ring kit
• Handle attachment hardware
• Registration card
Become familiar with each piece before assembling
the pressure washer. Check all contents against the
illustration shown on page 7. If any parts are missing
or damaged, call the pressure washer helpline at
1-800-222-3136.
ASSEMBLING YOUR PRESSURE
WASHER
Your Craftsman pressure washer was mostly
assembled at the factory. However, you will need to
perform these tasks before you can operate your
pressure washer:
• Attach handle and hooks.
• Attach hose reel.
• Add oil to engine crankcase.
• Add fuel to fuel tank.
• Connect high pressure hose to the spray gun and
the pump.
• Connect water supply to the pump.
Attach Handle and Hooks
• Place the handle onto the handle supports already
connected to the main unit. Make sure the holes in
the handle align with the holes on the handle
supports.
Handle
Align
Holes
Handle
Supports
NOTE: It may be necessary to move the handle
supports from side to side in order to align the handle
so it will slide over the handle supports.
• Insert the carriage bolt through the hole on the right
side of the handle (viewing from rear of unit) and
attach the plastic knob. Tighten the knob by hand.
• Insert one of the "L" bolts (detergent bottle hook)
through the hole on the left side of the handle
(viewing from rear of unit) and attach the plastic
knob. Tighten the knob by hand.
.J
Gun Hook
Detergent
Bottle Hook
I
• Insert the other "L" bolt (gun hook) through the hole
just under the billboard on the right side of the
handle (viewing from rear of unit). Hold the hook in
place with a pliers and attach the Iocknut with a
7/16" wrench.
NOTE: Be sure to hold the hook in place with the
pliers until tight.
Assembling Hose Reel
IMPORTANT: You must take the hose off the reel
when operating your pressure washer. The reel is for
storage purposes only.
• Attach the handle to the reel with Iocknuts, flat
washers, and bolts. Please note that the bolts are
inserted with their heads inside the hose reel.
Hose reel
Handle
Locknut
Flat washer
Bolt
Secure the hose reel on the handle, at the location
shown on page 7 with Iocknuts and bolts.
* The use of multi-viscosity oils (5W-30, 10W-30, etc.)
in temperatures above 40°F (4°C) will result in higher
than normal oil consumption. When using a multi-
viscosity oil, check oil more frequently.
** If using SAE 30 oil in temperatures below 40°F
(4°C), it will result in hard starting and possible
engine bore damage due to inadequate lubrication.
• Place pressure washer on a level surface.
• Clean area around oil fill.
• Remove oil fill cap.
• Pour oil slowly. Fill to the point of overflowing.
• Replace oil fill cap, tighten securely.
NOTE: Check oil often during engine break-in.
Add Gasoline
,_ WARNING! Never fill fuel tank indoors. Never
fill fuel tank when engine is running or hot. Do
Not smoke when filling fuel tank.
Clamp
Locknut
Hose Clip
Bolt
• Attach the spring clip with a black self tapping
screw in the hole provided on the clamp.
NOTE: There may be some hardware included with
the hose reel kit that is not used on this model.
Screw
Add Engine Oil
IMPORTANT: Any attempt to crank or start the engine
before it has been properly serviced with the
recommended oil may result in an engine failure.
NOTE: When adding oil to the engine crankcase, use
only high quality detergent oil rated with API service
classification SF, SG, SH, SJ or higher rated SAE 30
weight. Do Not use special additives.
• Choose a viscosity according to the table below:
,_ WARNING! Never fill fuel tank completely full.
Provide space for fuel expansion. Wipe away
any fuel spillage from engine and equipment
and let residue evaporate before starting.
• Use fresh, clean unleaded automotive gasoline and
store in approved, clean, covered containers. Use
clean fill funnels. Never use "stale" gasoline left
over from last season or gasoline stored for long
periods.
• Clean area around fuel fill cap, remove cap.
• Slowly add gasoline to fuel tank. Use a funnel to
prevent spillage. Fill tank to about 1.5" below top of
the filler neck to allow for fuel expansion.
_'_ _ r-Tank
• Install fuel cap and wipe up any spilled gasoline.
Uorrl_I(
4
F -20 0 20 32 40 60 80 100
'C -30' -20' -15 _ 15 20 30 45
STARTING TEMPERATURE RANGE ANTICIPATED BEFORE NEXT OIL CHANGE
Connect Hose and Water Supply to Pump
IMPORTANT: You must attach all hoses before you
start engine. Starting engine without all hoses
connected and water supplied will damage pump.
• Uncoil high pressure hose and attach one end of
hose to the base of the spray gun. Tighten by
hand.
• Attach other end of high pressure hose to the high
pressure outlet on the pump. Tighten by hand.
Connect the garden hose to the water inlet. Tighten
by hand.
Inspect inlet
screen. Do
use if
damaged;
'clean if dirty.
%.
CAUTION! There MUST be at least ten feet of
unrestricted garden hose between the pressure
washer inlet and any flow shut off device, such as a 'Y'
shut-off connector or other convenience-type water
shut-off valve. Damage to pressure washer resulting
from disregarding this warning will not be covered by
the warranty.
• Turn ON the water (open supply valve completely).
CAUTION! Before starting the pressure
washer, be sure you are wearing adequate
eye protection.
• Before you connect your garden hose to the water
inlet, inspect the inlet screen. Clean the screen if it
contains debris or have it replaced if damaged.
DO NOT RUN THE PRESSURE WASHER IF THE
INLET SCREEN IS DAMAGED. NEVER SIPHON
INLET WATER.
• Run water through garden hose for 30 seconds to
flush it of debris.
wlCt EI_ISTBEFORE STARTING
• assembled unit to ensure you have
Check that hose reel fasteners are tight.
Check that oil has been added to proper level in
erformed all of the following:
engine crankcase.
Add proper gasoline to fuel tank.
• Check for properly tightened hose connections
(high pressure and water supply) and that there are
no kinks, cuts, or damage to the high pressure
hose.
• Provide proper water supply (not to exceed 100°F).
• Be sure to read "Safety Rules" and "Operation"
sections before using the pressure washer.
• If starting unit after storage, see "Storage" section
on page 15.
KNOW YOUR PRESSURE WASHER
Read the owner's manual and safety rules before operating your pressure washer.
Compare the illustrations with your pressure washer to familiarize yourself with the locations of various controls
and adjustments. Save this manual for future reference.
Fuel Cap
Nozzle Extension
Adjustable Nozzle
Thermal Relief
Valve
Spray Gun Detergent Pick-Up
Tube and Filter
High Pressure Hose
Hose Reel
Choke Lever
Fuel Valve
Throttle Control Lever
Recoil Starter
(on front of engine)
Air Filter
Oil Fill Cap
Water Inlet
Adjustable Nozzle- Always attached to nozzle
extension. Pull back for high pressure or push forward
for low pressure; turn clockwise for narrow spray or
turn counterclockwise for fan spray.
Air Filter - Dry type filter element limits the amount of
dirt and dust that gets in the engine.
Choke Lever - Used to help start a cold engine.
Chemical Injection Siphon/Filter - Used to siphon
detergent from chemical bottle to the low pressure
water stream.
Fuel Valve -- Used to turn fuel on and off to engine.
Fuel Cap - Engine is filled with regular unleaded
gasoline here.
High Pressure Hose - Connect one end to the spray
gun and other end to the high pressure outlet.
High Pressure Outlet - Connection for high pressure
hose.
Pump
High Pressure Outlet
Hose Reel -- Used for storing hose while unit is not in
use. Hose must be detached from unit and spray gun
before storage.
Nozzle Extension - Attach to spray gun to use
adjustable nozzle.
Oil Fill Cap - Engine is filled with oil here. See page 5
for oil recommendations and filling instructions.
Pump - Develops high water pressure.
Recoil Starter- Used for starting the engine.
Spray gun - Controls the application of water onto
cleaning surface with trigger device. Includes safety
latch.
Thermal Relief Valve - Discharges pump water if it
becomes too hot.
Throttle Control Lever - Sets engine in starting
mode for recoil starter and stops running engine.
Water Inlet - Connection for garden hose.
HOW TO USE YOUR PRESSURE
WASHER
If you have any problems operating your pressure
washer, please call the pressure washer helpline at
1-800-222-3136.
To Start Your Pressure Washer
To start your engine-powered pressure washer for the
first time, follow these instructions step-by-step. This
starting information also applies whenever you start
the engine after you have let the pressure washer sit
idle for at least a day.
• Place the pressure washer in an area close
enough to an outside water source capable of
supplying water at a flow rate greater than
2.4 gallons per minute.
• Check that the high pressure hose is tightly
connected to the spray gun and to the pump. See
"Assembling Your Pressure Washer" for
illustrations.
• Make sure unit is in a level position.
• Connect the garden hose to the water inlet on the
pressure washer pump. Turn ON the water.
CAUTION! Do Not run the pump without the water
supply connected and turned on. You must follow this
caution or the pump will be damaged.
• Squeeze trigger on gun to purge pump system of
air and impurities.
• Attach nozzle extension to spray gun. Tighten by
hand.
• Position the nozzle in the low pressure mode (slide
nozzle forward) and squeeze the trigger on the
spray gun to relieve pressure caused by turning
ON the water. Water will flow out of the gun in a
thin stream. Continue to hold trigger until there is a
steady stream of water and no air remains in the
system. Release the trigger.
• Engage the safety latch to the spray gun trigger.
@ Safety Latch
• Rotate the fuel shut-off valve to the "On" position
(fully counter-clockwise).
Fuel Valve shown in
"On" position
• Move the throttle lever to "Fast" position.
Throttle Lever in
"Fast" Position
• Move the choke lever to the "Choke" position.
Choke Lever "
Shown in
"Run" Position
NOTE: For a warm engine, be sure the choke lever is
in the "Run" position.
• Grasp the unit's handle with your left hand. Pull the
starter grip lightly with your right hand until you feel
some resistance, then pull briskly.
• Return the starter grip handle slowly. Do Not let
rope "snap back" against starter.
• When engine starts, slowly move choke lever to
the "Run" position. If engine falters, move choke
lever to the "Choke" position, then to the "Run"
position.
• If engine fails to start after six pulls, move choke
lever to the "Run" position. If engine fires, but does
not continue to run, move choke lever to the
"Choke" position, then to the "Run" position.
NOTE: If the recoil starter is hard to pull, it may be
necessary to squeeze the gun trigger to relieve
internal pump pressure.
How to Stop Your Pressure Washer
• Move throttle lever to "Stop" position.
• Turn the fuel shut-off valve to the "Off" position
(fully clockwise).
• Squeeze trigger on the spray gun to relieve
pressure in the hose.
NOTE: A small amount of water will squirt out when
you release the pressure.
How To Use the Adjustable Nozzle
Now that you know how to START and STOP your
pressure washer, the information in this section will tell
you how to adjust the spray pattern and apply
detergent or other cleaning chemicals.
_ CAUTION! Never adjust spray pattern when
spraying. Never put hands in front of nozzle to
adjust spray pattern.
On the end of your spray gun is an adjustable nozzle
that you can use to adjust the spray pattern and the
spray pressure.
• Slide the nozzle forward for low pressure spray;
slide it backward for high pressure spray.
• For most effective cleaning, keep the spray nozzle
between 8 to 24 inches away from cleaning
surface.
• If you get the spray nozzle too close, especially
using high pressure mode, you may damage the
surface being cleaned.
• Do Not get closer than 8 inches when cleaning
tires.
Applying Detergent with the Adjustable
Nozzle
IMPORTANT: Use chemicals designed specifically
for pressure washers, Household detergents could
damage the pump.
IMPORTANT: You MUST attach all hoses before you
start the engine. Starting the engine without all the
hoses connected and without the water turned ON will
damage the pump.
To apply detergent, follow these steps:
• Review the use of the adjustable nozzle.
• Prepare detergent solution as required by the job.
• Hang the detergent solution container on the
lowest hook attached to the handle.
Slide nozzle backward for Slide nozzle forward for
high pressure mode. low pressure mode and
detergent application.
• Point the nozzle towards a hard surface, disengage
the safety latch, and press the trigger to test the
pattern.
Rotating the nozzle adjusts the spray pattern from
a narrow pattern to a fan pattern.
Twist nozzle counter-
clockwise for fan pattern.
Twist nozzle clockwise for
narrow spray pattern.
• Place the filter end of the detergent siphoning tube
into the detergent container.
CAUTION! When inserting the filter into the detergent
container, route the tube so as to keep it from
inadvertently contacting the hot muffler.
• Slide the adjustable nozzle forward to low pressure
mode. Detergent cannot be applied with the nozzle
in high pressure position.
• Make sure the garden hose is connected to the
water inlet. Check that the high pressure hose is
connected to the spray gun and the pump. Start
the engine.
• Apply detergent to a dry surface, starting from the
bottom and working up.
• Allow the detergent to "soak in" for 3-5 minutes
before rinsing. Reapply as needed to keep the
surface wet.
• For washing, start at lower portion of area to be
washed and work upward, using long, even,
overlapping strokes.
Pressure Washer Rinsing
WARNING! Be extremely careful if you use the
pressure washer from a ladder, scaffolding or
any other relatively unstable location. Pressure
in a running washer builds as you climb. When
you press the trigger, the recoil from the initial
spray could cause you to fall. The high pressure
spray could also cause you to fall if you are too
close to the cleaning surface.
For Rinsing:
• Slide the nozzle backward to high pressure, press
the trigger and wait for the detergent to clear.
NOTE: You can also stop detergent flow by removing
detergent siphoning tube from container.
• Keep the spray gun a safe distance from the area
you plan to spray.
• Apply a high pressure spray to a small area, then
check the surface for damage. If no damage is
found, it is okay to continue cleaning.
• Start at the top of the area to be rinsed, working
down with same overlapping strokes as you used
for washing and applying detergent.
Automatic Cool Down System
(Thermal Relief)
If you run the engine on your pressure washer for
3-5 minutes without pressing the trigger on the spray
gun, circulating water in the pump can reach
temperatures between 140-145°F. The automatic cool
down system engages at this temperature and cools
the pump by discharging the warm water onto the
ground, preventing internal pump damage.
How to Use the Hose Reel
Your pressure washer is equipped with a hose reel
that is designed to store your hose when unit is not in
use. These instructions are for short term storage
only. For long term storage see "Storage" on page 15.
After each use:
• Disconnect hose from spray gun and high pressure
outlet on pump.
• Drain water from hose.
• Slide one end of the hose into the hole on the hose
reel. Turn the hose reel with the handle to coil the
hose onto the reel.
ring
l "
• Push the other end of the hose into the clip on the
handle of your unit.
IMPORTANT: Do Not use your pressure washer with
the hose coiled onto the hose reel. The hose reel is for
storage purposes only.
Adjustable Hose Reel Spring Tension
The hose reel is provided with a spring tension
adjustment knob, as shown above.
Although the operator can loosen or tighten the knob
to achieve the desired reel tension, the manufacturer
recommends that the knob be fully hand tightened
(clockwise).
Tension
Knob
10
OWNER'S RESPONSIBILITIES
Follow the hourly or calendar intervals, whichever occurs first.
More frequent service is required when operating in adverse conditions noted below.
MAINTENANCE SCHEDULE
FILL IN DATES AS YOU COMPLETE
REGULAR SERVICE
HOURLY OPERATING
INTERVAL
SERVICE DATES
MAINTENANCE TASK
PRESSURE WASHER
Check/clean water inlet screen
Check hiah pressure hose
Check deteraent hose
Check spray gun and assembly for
leaks
Purae Duma of air and contaminants
Prepare pump for storaqe below 32°F
ENGINE
Check oil level
Chanae enaine oil
Service air cleaner
Service spark Dlua
Service spark arrester
Prepare for storage
1 Clean if clogged. Replace if perforated or torn.
2 Change oil after the first (5) operating hours and every 50 hours or every year, whichever occurs first, thereafter.
Change sooner when operating under dirty or dusty conditions.
Replace more often under dirty or dusty conditions.
Before Hours or Hours or
Each Use Yearly Yearly
X1
x
x
x ............
X
x .....! i!!!,;iiiiiill
}_ }; x
}) x
PRODUCT SPECIFICATIONS
Pressure Washer Specifications
Pressure ................... 2400 PSI
Flow Rate .................. 2.2 GPM
Chemical Mix ............... Use as directed
Water Supply Temperature ..... Not to Exceed 100°F
Shipping Weight ............. 94 Ibs.
Engine Specifications
Rated Horsepower ........... 6.5 liP
Spark Plug Type:
Resistor ............... Champion RC12YC
Long Life Platinum ....... Champion RC12PYP
Set Gap To: .............. 0.020 inches(0.50 mm)
Gasoline Capacity ............ 3.0 Quarts
Oil
Every 50 Every 100
See"Storage on 'age 15
x_
x3
If unit is to remain idle for
Ionqer than 30 days.
GENERAL RECOMMENDATIONS
The pressure washers warranty does not cover items
that have been subjected to operator abuse or
negligence. To receive full value from the warranty,
the operator must maintain pressure washer as
instructed in this manual including proper storage as
detailed in "Storage" on page 15.
Some adjustments will need to be made periodically to
properly maintain your pressure washer.
All service and adjustments should be made at least
once each season. Follow the requirements in the
"Maintenance Schedule" chart above.
NOTE: Once a year you should clean or replace the
spark plug and replace the air filter. A new spark plug
and clean air filter assure proper fuel-air mixture and
help your engine run better and last longer.
Above 40°F .......... SAE 30
0°F - 40°F ........... SAE 5W-30 or 10W-30
11
BEFORE EACH USE
• Check engine oil level.
• Check water inlet screen for damage.
• Check high pressure hose for leaks.
• Check chemical filters for damage.
• Check spray gun and nozzle extension assembly
for leaks.
• Purge pump of air and contaminants.
PRESSURE WASHER
MAINTENANCE
Check and Clean Inlet Screen
Examine garden hose inlet screen. Clean if it is
clogged or replace if it is torn.
Check High Pressure Hose
High pressure hoses can develop leaks from wear,
kinking, or abuse. Inspect hose before each use.
Check for cuts, leaks, abrasions, bulging of cover, or
damage or movement of couplings. If any of these
conditions exist, replace hose immediately.
_ ANGER! Never repair a high pressure hose.
Replace with hose that exceeds the maximum
pressure rating of your pressure washer.
Check Spray Gun and Nozzle Extension
Examine hose connection to spray gun and make sure
it is secure. Test trigger by pressing it and making
sure it springs back into place when you release it.
Engage safety latch and test trigger. You should not
be able to press trigger. Replace spray gun
immediately if it fails any of these tests.
Check In-Line Filter
Refer to the illustrationand service the in-line filter if it
becomes clogged, as follows:
In-line Filter
Nozzle Extension _O _(._)
O-ring
.
Detach spray gun and nozzle extension from high
pressure hose. Detach nozzle extension from
spray gun and remove o-ring and screen from
nozzle extension. Flush the screen, spray gun,
and nozzle extension with clean water to clear
debris.
.
If the screen is damaged, the o-ring kit contains a
replacement in-line filter screen and an o-ring. If
undamaged, reuse screen.
. Place the in-line filter screen into the threaded end
of the nozzle extension. Direction does not matter.
Push the screen in with the eraser end of a pencil
until it rests flat at the bottom of the opening. Take
care to not bend the screen.
4. Place the o-ring into the recess. Push the o-ring
snugly against the in-line filter screen.
5. Assemble the nozzle extension to the spray gun,
as described earlier in this manual.
Purge Pump of Air and Contaminants
To remove air from the pump, follow these steps:
• Set up the pressure washer as described in the
ASSEMBLY section and connect the water supply.
• Pull the trigger on the spray gun and hold until a
steady stream of water appears.
To remove contaminants from the pump, follow these
steps:
• Set up the pressure washer as described in the
ASSEMBLY section, and connect the water supply.
• Remove the nozzle extension from the spray gun.
• Start the engine according to instructions in
OPERATION section.
• Pull the trigger on the spray gun and hold.
• When the water supply is steady and constant,
engage the safety latch and refasten the nozzle
extension.
Nozzle Maintenance
A pulsing sensation felt while squeezing the spray gun
trigger may be caused by excessive pump pressure.
The principal cause of excessive pump pressure is a
nozzle clogged or restricted with foreign materials,
such as dirt, etc. To correct the problem, immediately
clean the nozzle using the tools included with your
pressure washer and follow these instructions:
1. Shut off the engine and turn off the water supply.
2. Detach the nozzle extension from the spray gun.
Twist the nozzle clockwise to the stream position.
Using the supplied 2mm (5/64) allen wrench,
remove the nozzle from the end of the nozzle
extension.
\
.
Remove the in-line filter from the other end of the
nozzle extension.
4.
Use the wire included in the kit (or a small paper
clip) to free any foreign material clogging or
restricting the nozzle.
12
Insert wire into nozzle and turn back
and forth to clear obstruction.
5. Using a garden hose, remove additional debris by
back flushing water through the nozzle extension.
Back flush between 30 to 60 seconds. Turn the
adjustable nozzle extension to stream spray and
move the nozzle from low to high while flushing.
6. Reinstall the nozzle and in-line filter into the
nozzle extension. Do Not overtighten the nozzle
with the allen wrench.
7. Reconnect the nozzle extension to the spray gun.
8. Reconnect the water supply, turn on the water,
and start the engine.
9. Test the pressure washer by operating with nozzle
in the high and in the low positions.
O-RING MAINTENANCE
Your pressure washer uses o-rings to keep hose and
spray gun connections tight and leak-free. Through
the normal operation of your unit, these o-rings may
become worn or damaged.
Provided with your pressure washer is an O-Ring
Maintenance Kit which includes replacement o-rings,
rubber washer and water inlet filter. Refer to the
instruction sheet provided in the kit to service your
unit's o-rings. Note that not all of the parts in the kit
will be used on your unit.
Parts in the O-Ring Kit Include:
• 1 o-ring, red, (p/n B2726) for the end of the spray
gun connection between spray gun and nozzle
extension.
O
• 1 o-ring, yellow, (p/n B2264) for the end of the
high pressure hose.
NOTE: The above two o-rings are close in size.
Please match carefully to assure proper o-ring usage.
• 1 water inlet screen (p/n B2384) for the garden
hose connector.
To remove a worn or damaged O-Ring:
• Use a small flathead screwdriver to get underneath
the o-ring and pry it off.
ENGINE MAINTENANCE
Checking Oil Level
Oil level should be checked prior to each use or at
least every 5 hours of operation. Keep oil level
maintained.
Changing Oil
Change engine oil after the first 5 hours and every
50 hours thereafter. If you are using your pressure
washer under extremely dirty or dusty conditions, or in
extremely hot weather, change oil more often.
Change oil while engine is still warm from running, as
follows:
• Drain fuel tank by running pressure washer until
fuel tank is empty.
• Disconnect spark plug wire and keep it away from
the spark plug.
• Remove oil drain plug and drain oil into appropriate
receptacle.
• Reinstall drain plug. Remove oil fill cap.
• Fill to point of overflowing at oil fill cap with
recommended oil.
• Reinstall oil fill plug and tighten securely.
• Wipe up any remaining oil.
• Reconnect spark plug wire to the spark plug.
13
Service Air Cleaner
Your engine will not run properly and may be
damaged if you run it with a dirty air cleaner.
Replace the air cleaner every 100 hours of operation
or once each year, whichever comes first. Replace
more often if operating under dirty or dusty conditions.
To service the air cleaner, follow these steps:
• Loosen screw and tilt cover down.
• Carefully remove cartridge assembly.
• To clean cartridge, gently tap pleated paper side
on a flat surface.
• Reinstall clean or new cartridge inside cover.
Tabs and Slots
Cartridge
Service Spark Plug
Service the spark plug every 100 hours of operation or
yearly, whichever occurs first.
,_ CAUTION! Disconnect spark plug wire from
spark plug and keep wire away from spark plug
while servicing engine.
• Clean area around spark plug.
• Remove and inspect spark plug.
• Replace spark plug if the electrodes are worn, or if
the insulator is cracked or chipped.
• For replacement use either the standard resistor
spark plug, Champion RC12YC or the long life
platinum spark plug, Champion RC12PYP.
• Check electrode gap with wire feeler gauge and set
gap at 0.020 inches (0.50mm), if necessary.
Base
Screw Cover
• Insert cover's tabs into slots in bottom of base.
• Tilt cover up and tighten screw securely to base.
NOTE: You can purchase new air filter elements by
calling 1-800-366-PART.
• Install spark plug, tighten securely.
NOTE: You can purchase a new spark plug by calling
1-800-366-PART.
Carburetor
If you think your carburetor needs adjusting, see your
nearest Sears service center. Engine performance
may be affected at attitudes above 7000 feet. For
operation at higher elevations, contact your nearest
Sears service center.
Spark Arrester Service
Your engine is not factory-equipped with a spark
arrester. In some areas, it is illegalto operate an
engine without a spark arrester. Check local laws and
regulations. A spark arrester is available from your
nearest Sears service center. If you need to order a
spark arrester, please call 1-800-366-PART.
The spark arrester must be serviced every 50 hours to
keep it functioning as designed.
If the engine has been running, the muffler will be very
hot. Allow the muffler to cool before servicing the
spark arrester.
• Remove spark arrester screen for cleaning and
inspection.
• Replace if screen is damaged.
14
Loading...