Craftsman 580767100 Owner’s Manual
Owner's Manual
CRRFTSMRN°
5.0 HORSEPOWER
2,100 PSI
2.0 GPM
HIGH PRESSUR
Model No. 580.767100
WASHER
HOURS: Mon.- Fri. 8 a.m. to 5 p.m. (CT)
CAUTION" Before using this product,
read this manual and follow all Safety
Rules and Operating Instructions.
SEARS, ROEBUCK and CO., Hoffman Estates, IL 60179 U.S.A.
Visit our Craftsman website: www.sears.com/craftsman
Part No. 187686 Draft 3 (4/6/2001)
• Safety
• Assembly
• Operation
• Maintenance
• Parts
• Espahol
WARRANTY ................................... 2
SAFETY RULES .............................. 2-3
ASSEMBLY .................................. 4-5
OPERATION ................................. 6-9
MAINTENANCE ............................ 10-13
SPECIFICATIONS ............................. 10
STORAGE ................................... 14
TROUBLESHOOTING .......................... 15
REPLACEMENT PARTS ...................... 16-23
EMISSION CONTROL WARRANTY ................ 24
ESPANOL ................................. 25-39
HOW TO ORDER PARTS ............... BACK PAGE
LIMITED WARRANTY ON CRAFTSMAN HIGH PRESSURE WASHER
For one year from the date of purchase, when this Craftsman pressure washer is maintained and operated
according to the instructionsin the owner's manual, Sears will repair, free of charge, any defect in material and
workmanship.
If this washer is used for commercial purposes, this warranty applies for only 90 days from the date of
purchase. If this high pressure washer is used for rental purposes, this warranty applies for only 30 days after
date of purchase.
This warranty does not cover:
• Expendable items such as spark plugs or air filters, which become worn during normal use.
• Repairs necessary because of operator abuse or negligence, including damage resulting from no water
being supplied to pump or failure to maintain the equipment according to the instructions contained in the
owner's manual.
Warranty service is available by returning the high pressure washer to the nearest Sears service center or
dealer in the United States.
This warranty gives you specific legal rights and you may also have other rights, which vary from state to state.
Sears, Roebuck and Co., Dept. 817WA, Hoffman Estates, IL 60179
This is the safety alert symbol. It is used to alert you to potential personal injury hazards.
Obey all safety messages that follow this symbol to avoid possible injury or death.
,_ WARNING! Gasoline is highly FLAMMABLE
and its vapors are EXPLOSIVE. Do Not permit
The engine exhaust from this product
contains chemicals known to the State of
California to cause cancer, birth defects, or
other reproductive harm.
CAUTION! When setting up, transporting,
adjusting or making repairs to your high
pressure washer, always disconnect the spark
plug wire from the spark plug and place the wire
where it cannot contact spark plug.
DANGER! Engine exhaust gases contain
DEADLY carbon monoxide gas. This dangerous
gas, if breathed in sufficient concentrations, can
cause unconsciousness or even death. Operate
this equipment only in the open air where
adequate ventilation is available.
smoking, open flames, sparks or heat in the
vicinity while handling gasoline. Avoid spilling
gasoline on a hot engine. Allow unit to cool
before refueling. Comply with all laws regulating
storage and handling of gasoline.
Read this manual carefully and become familiar
with your pressure washer. Know its applications,
its limitations, and any hazards involved.
• Locate this pressure washer in areas away from
combustible materials, combustible fumes or dust.
• The high pressure equipment is designed to be
used with Sears authorized parts only. If you use
this equipment with parts that do not comply with
minimum specifications, the user assumes all risks
and liabilities.
• Somechemicalsordetergentsmaybeharmfulif
inhaledoringested,causingseverenausea,
faintingorpoisoning.Theharmfulelementsmay
causepropertydamageorsevereinjury.
• DoNotallowCHILDRENtooperatethepressure
washerat anytime.
• Operateengineonlyatgovernedspeed.Running
theengineatexcessivespeedsincreasesthe
hazardofpersonalinjury.DoNottamperwithparts
whichmayincreaseordecreasethegoverned
speed.
• DoNotwearlooseclothing,jewelryoranything
thatmaybecaughtinthestarterorotherrotating
parts.
• Beforestartingthepressurewasherincold
weather,checkallpartsoftheequipmentandbe
sureicehasnotformedthere.See"Storage"on
page14forcoldweatherprotection.
• Neveruseaspraygunwhichdoesnothavea
triggerlockortriggerguardin placeandinworking
order.
• Keepthehoseconnectedtomachineorthespray
gunwhilethesystemispressurized.Disconnecting
thehosewhiletheunitispressurizedisdangerous.
• Neveroperateunitswithbrokenormissingparts,
orwithoutprotectivehousingorcovers.
• Checkthefuelsystemforleaksorsignsof
deterioration,suchaschafedorspongyhose,
looseormissingclamps,ordamagedtankorcap.
Correctalldefectsbeforeoperatingthepressure
washer.
• DoNotsprayflammableliquids.
• Usearespiratorormaskwheneverthereisa
chancethatvaporsmaybeinhaled.Readall
instructionswithmasksoyouarecertainthemask
willprovidethenecessaryprotectionagainst
inhalingharmfulvapors.
• Neveraimthegunatpeople,animalsorplants.
Thehighpressurestreamofwaterthatthis
equipmentproducescanpierceskinandits
underlyingtissues,leadingtoseriousinjuryand
possibleamputation.
• Neverallowanypartofthebodytocomein
contactwiththefluidstream.DoNotcomein
contactwithafluidstreamcreatedbyaleakinthe
highpressurehose.
• Alwaysweareyeprotectionwhenyouusethis
equipmentorwhenyouareinthevicinitywhere
theequipmentisinuse.
• Highpressurespraycancausepaintchipsorother
particlesto becomeairborne.
• DoNotoperatethepressurewasherabovethe
ratedpressure.
• Nevermovethemachinebypullingonthehigh
pressurehose.Usethehandleprovidedonthe
unit.
• Alwaysbecertainthespraygun,nozzlesand
accessoriesarecorrectlyattached.
• DoNotsecurethesprayguninthe(open)
position.
• Highpressurespraymaydamagefragileitems
includingglass.DoNotpointspraygunat glass
wheninthejetspraymode.
• Holdthespraygunfirmlyinyourhandbeforeyou
starttheunit.Failureto dosocouldresultinan
injuryfromawhippingspraygun.DoNotleavethe
spraygununattendedwhilethemachineis
running.
• Thecleaningareashouldhaveadequateslopes
anddrainagetoreducethepossibilityofafalldue
toslipperysurfaces.
• Keepwatersprayawayfromelectricwiringorfatal
electricshockmayresult.
• DoNotby-passanysafetydeviceonthis
machine.
• Themufflerandengineheatupduringoperation
andremainhotimmediatelyaftershuttingitdown.
Avoidcontactwithahotmufflerorengineasyou
couldbeseverelyburned.
• Operateandstorethisunitonastablesurface.
• Highpressurehosecandevelopleaksfromwear,
kinking,abuse,etc.Watersprayingfromaleakis
capableofinjectingmaterialintoskin.Inspecthose
eachtimebeforeusingit.Checkallhosesforcuts,
leaks,abrasionsorbulgingofcover,ordamageor
movementofcouplings.Ifanyoftheseconditions
exist,replacehoseimmediately.Neverrepairhigh
pressurehose.Replaceitwithanotherhosethat
meetsmaximumpressureratingofyourunit.
• Themufflerandaircleanermustbeinstalledandin
goodconditionbeforeoperatingthepressure
washer.Thesecomponentsactassparkarresters
iftheenginebackfires.
IntheStateofCaliforniaa sparkarresterisrequiredby
law(Section4442oftheCaliforniaPublicResources
Code).Otherstatesmayhavesimilarlaws.Federal
lawsapplyonfederallands.
NOTE:Ifyouequipthemufflerwithasparkarrester,it
mustbemaintainedineffectiveworkingorder.Youcan
ordera sparkarresterthroughyourauthorizedSears
servicedealer.
Yourpressurewasherrequiressomeassemblyandis
readyforuseonlyafterithasbeenproperlyserviced
withtherecommendedoilandfuel.
Ifyou haveanyproblemswiththeassemblyof
your pressurewasher,pleasecallthepressure
washerhelplineat1-800-222-3136.
IMPORTANT:Anyattempttoruntheenginebeforeit
hasbeenservicedwiththerecommendedoilwillresult
inanenginefailure.
REMOVE PRESSURE WASHER
FROM CARTON
• Open carton and slice two corners opposite guide
handle from top to bottom so the panel can be
folded down flat.
• Remove fillers and parts box shipped with your
pressure washer.
• Roll the pressure washer out the open end of the
carton.
• Raise guide handle, secure in place.
ASSEMBLING YOUR PRESSURE
WASHER
Your Craftsman high pressure washer was mostly
assembled at the factory. However, you will need to
perform these tasks before you can operate your
pressure washer:
• Add oil to engine crankcase.
• Add fuel to fuel tank.
• Connect high pressure hose to the spray gun and
the pump.
• Connect water supply to the pump.
Add Engine Oil
IMPORTANT: Any attempt to crank or start the engine
before it has been properly serviced with the
recommended oil may result in an engine failure.
NOTE: When adding oil to the engine crankcase, use
only high quality detergent oil rated with API service
classification SF, SG, SH, SJ or higher rated SAE 30
weight. Do Not use special additives.
• Choose a viscosity according to the table below.
Lift the handle to upright
position and slide the
locking caps into place.
• Check carton for additional loose parts.
CARTON CONTENTS
Check all contents. If any parts are missing or
damaged, call the pressure washer helpline at
1-800-222-3136.
• The main unit
• Parts box (which includes items listed below)
High pressure hose
Spray gun
Nozzle extension with adjustable nozzle
Engine oil
Owner's manual
Nozzle cleaning kit
O-Ring maintenance kit
Registration card
Become familiar with each piece before assembling
the pressure washer. Compare contents against the
view on page 6. If any parts are missing or damaged,
call the pressure washer helpline at 1-800-222-3136.
_o_Io_
F -20 0 20 32 40 60 80 100
n n n I n n n n
C -3'0 -2'0 -1'0 0 1'0 25 30 4'0
STARTING TEMPERATURE RANGE ANTICIPATED BEFORE NEXT OIL CHANGE
* The use of multi-viscosity oils (5W-30, 10W-30, etc.)
in temperatures above 40°F (4°C) will result in higher
than normal oil consumption. When using a multi-
viscosity oil, check oil more frequently.
** If using SAE 30 oil in temperatures below 40°F
(4°C), it will result in hard starting and possible
engine bore damage due to inadequate lubrication.
• Place pressure washer on a level surface.
• Clean area around oil fill.
• Remove oil fill cap and dipstick.
• Wipe dipstick clean, insert it into oil fill hole and
tighten securely, remove dipstick. Add
recommended oil up to "Full" mark on dipstick.
@
Pour slowly. Wipe dipstick clean each time oil level
is checked. Do Not overfill.
• Installoilfillpluganddipstick,tightensecurely.
NOTE:Checkoiloftenduringenginebreak-in.
Add Gasoline
_ ARNING! Never fill fuel tank indoors. Never
fill fuel tank when engine is running or hot. Do
Not smoke when filling fuel tank.
_ ARNING! Never fill fuel tank completely full.
Provide space for fuel expansion. Wipe away
any fuel spillage from engine and equipment
before starting.
• Use clean unleaded automotive gasoline and store
in approved, clean, covered containers. Use clean
fill funnels. Never use "stale" gasoline left over
from last season or gasoline stored for long
periods.
• Clean area around fuel fill cap, remove cap.
• Slowly add gasoline to fuel tank. Use a funnel to
prevent spillage. Fill tank to about 1.5" below the
top of the filler neck.
_ _ _ /Tank
• Install fuel cap and wipe up any spilled gasoline.
Connect Hose and Water Supply to Pump
IMPORTANT: You must assemble nozzle extension
and attach all hoses before you start engine. Starting
engine without all hoses connected and water
supplied will damage pump.
• Uncoil high pressure hose and attach one end of
hose to the base of the spray gun. Tighten by
hand.
• Attach other end of high pressure hose to the high
pressure outlet on the pump. Tighten by hand.
Before you connect your garden hose to the water
inlet, inspect the inlet screen. Clean the screen if it
contains debris or have it replaced if damaged.
Do Not run the pressure washer if the inlet
screen is damaged. Never siphon inlet water.
Run water through garden hose for 30 seconds to
flush out any debris.
Inspect inlet
screen. Do
Not use if
ged;
clean if dirty.
• Connect the garden hose to the water inlet. Tighten
by hand.
CAUTION! There MUST be at least ten feet of
unrestricted garden hose between the pressure
washer inlet and any flow shut off device, such as a 'Y'
shut-off connector or other convenience-type water
shut-off valve. Damage to pressure washer resulting
from disregarding this warning will not be covered by
the warranty.
• Turn ON the water and squeeze the trigger on the
gun to purge the pump system of air and
impurities.
_ CAUTION! Before starting the pressure
washer, be sure you are wearing adequate
eye protection.
CHECKLIST BEFORE STARTING
ENGINE
Review the unit to ensure you have performed all of
the following:
• Check that oil has been added to proper level in
engine crankcase.
• Add proper gasoline to fuel tank.
• Check for properly tightened hose connections
(high pressure and water supply) and that there are
no kinks, cuts, or damage to the high pressure
hose.
• Provide proper water supply (not to exceed 100°F).
• Be sure to read "Safety Rules" and "Operation"
sections before using the pressure washer.
• If starting unit after storage, see "Storage" section
on page 14.
KNOW YOUR PRESSURE WASHER
Read the owner's manual and safety rules before operating your pressure washer.
Compare the illustrations with your pressure washer to familiarize yourself with the locations of various controls
and adjustments. Save this manual for future reference.
High Pressure Hose
Spray Gun
Throttle Control
Lever
Choke Lever
Air Filter
Nozzle Extension
Adjustable Nozzle
Recoil Starter
Gas Cap
Detergent Pick-Up
Tube and Filter
Oil Fill Cap and Dipstick
Water Inlet
High Pressure Outlet
Pump
Adjustable Nozzle - Adjust for high or low pressure;
narrow or fan spray.
Air Filter - Dry type filter element limits the amount of
dirt and dust that gets in the engine.
Choke Lever - Used to help start a cold engine.
Detergent Pick-Up Tube and Filter- Used to siphon
detergent from chemical bottle to the low pressure
water stream.
Gas Cap - Fill fuel tank with regular unleaded
gasoline here.
High Pressure Hose - Connect one end to the spray
gun and other end to the high pressure outlet.
High Pressure Outlet - Connection for high pressure
hose.
Nozzle Extension - Attached to spray gun for more
convenient use.
Oil Fill Cap and Dipstick - Check and fill engine with
oil here. See page 4 for oil recommendations and
filling instructions.
Pump - Develops high water pressure.
Recoil Starter- Used for starting the engine.
Spray Gun - Controls the application of water onto
cleaning surface with trigger device. Includes safety
latch.
Throttle Control Lever - Sets engine in starting
mode for recoil starter and stops running engine.
Water Inlet - Connection for garden hose.
HOW TO USE YOUR PRESSURE
WASHER
If you have any problems operating your pressure
washer, please call the pressure washer helpline at
1-800-222-3136.
To Start Your Pressure Washer
To start your engine-powered pressure washer for the
first time, follow these instructions step-by-step. This
starting information also applies whenever you start
the engine after you have let the pressure washer sit
idle for at least a day.
• Place the pressure washer in an area close
enough to an outside water source capable of
supplying water at a flow rate greater than
2.2 gallons per minute.
• Check that the high pressure hose is tightly
connected to the spray gun and to the pump. See
"Assembling Your Pressure Washer" for
illustrations.
• Make sure unit is in a level position.
• Connect the garden hose to the water inlet on the
pressure washer pump. Turn ON the water.
CAUTION! Do Not run the pump without the water
supply connected and turned on. You must follow this
caution or the pump will be damaged.
• Squeeze trigger on gun to purge pump system of
air and impurities.
• Attach nozzle extension to spray gun. Tighten by
hand.
• Move the throttle lever to "Fast" position, shown
here as a rabbit.
• Move the choke lever to the "Choke" position.
NOTE: For a warm engine, be sure the choke lever is
in the "Run" position.
• Place your left foot on the lower frame and grasp
the handle as shown. Your unit may appear slightly
different from that shown here.
• Position the nozzle in the low pressure mode (slide
nozzle forward) and squeeze the trigger on the
spray gun to relieve pressure caused by turning
ON the water. Water will flow out of the gun in a
thin stream. Continue to hold trigger until there is a
steady stream of water and no air remains in the
system. Release the trigger.
• Engage the safety latch to the spray gun trigger.
y Latch
• Pull the starter grip handle lightly with your right
hand until you feel some resistance, then pull
briskly.
• Return the starter grip handle slowly. Do Not let
rope "snap back" against starter.
• When engine starts, slowly move choke lever to
the "Run" position. If engine falters, move choke
lever to the "Choke" position, then to the "Run"
position.
• If engine fails to start after six pulls, move choke
lever to the "Run" position. If engine fires, but does
not continue to run, move choke lever to the
"Choke" position, then to the "Run" position.
NOTE: If the recoil starter is hard to pull, it may be
necessary to squeeze the gun trigger to relieve
internal pump pressure.
How to Stop Your Pressure Washer
• Move the throttle lever to "Stop" position.
• Squeeze trigger on the spray gun to relieve
pressure in the hose.
NOTE: A small amount of water will squirt out when
you release the pressure.
How To Use the Adjustable Nozzle
You now should know how to START your pressure
washer and how to STOP it. The information in this
section will tell you how to adjust the spray pattern
and apply detergent or other cleaning chemicals.
_ CAUTION! Never adjust spray pattern when
spraying. Never put hands in front of nozzle to
adjust spray pattern.
On the end of your spray gun is a nozzle handle that
can adjust the spray pressure and the spray pattern.
• Point the nozzle toward the ground, disengage the
safety latch, and press the trigger to test the
pattern.
Rotating the nozzle adjusts the spray pattern from
a narrow pattern to a fan pattern.
I ,
Twist nozzlecounter- Twist nozzle clockwise for
clockwise for fan pattern, narrow spray pattern.
For most effective cleaning, keep the spray nozzle
between 8 to 24 inches away from cleaning
surface.
If you get the spray nozzle too close, especially
using high pressure mode, you may damage the
surface being cleaned.
Do Not get closer than 8 inches when cleaning
tires.
Sliding the nozzle forward and back adjusts the
spray pressure.
Applying Detergent with Adjustable Nozzle
IMPORTANT: Use chemicals designed specifically for
pressure washers. Household detergents could
damage the pump.
IMPORTANT: You must attach all hoses before you
start the engine. Starting the engine without all the
hoses connected and without the water turned ON will
damage the pump.
To apply detergent, follow these steps:
• Review the use of the adjustable nozzle.
• Prepare the detergent solution as required by the
job.
• Hang the detergent solution container on the hook
attached to the handle.
Slide nozzle backward for
high pressure mode.
Slide nozzle forward for low
pressure mode and
detergent application.
• Place the filter end of the detergent siphoning tube
into the detergent container.
CAUTION! When inserting the filter into the detergent
container, route the tube so as to keep it from
inadvertently contacting the hot muffler.
• Slide the adjustable nozzle forward to low pressure
mode. Detergent cannot be applied with the nozzle
in high pressure position.
• Make sure the garden hose is connected to the
water inlet. Check that the high pressure hose is
connected to the spray gun and the pump. Start
the engine.
• Apply detergent to a dry surface, starting from the
bottom and working up.
• Allow the detergent to "soak in" for 3-5 minutes
before rinsing. Reapply as needed to prevent
surface from drying.
• For washing, start at lower portion of area to be
washed and work upward, using long, even,
overlapping strokes.
IMPORTANT: You must flush the chemical injection
system after each use by placing the filter into a clean
bucket of water and running the pressure washer in
low pressure for 1-2 minutes.
Pressure Washer Rinsing
_ ARNING! Be extremely careful if you use the
pressure washer from a ladder, scaffolding or
any other relatively unstable location. Pressure
in a running washer builds as you climb. When
you press the trigger, the recoil from the initial
spray could cause you to fall. The high pressure
spray could also cause you to fall if you are too
close to the cleaning surface.
For Rinsing:
• Slide the nozzle backward to high pressure, press
the trigger and wait for the detergent to clear.
NOTE: You can also stop detergent flow by removing
detergent siphoning tube from container.
• Keep the spray gun a safe distance from the area
you plan to spray.
• Apply a high pressure spray to a small area, then
check the surface for damage. If no damage is
found, it is okay to continue cleaning.
• Start at the top of the area to be rinsed, working
down with same overlapping strokes as you used
for washing and applying detergent.
Automatic Cool Down System
(Thermal Relief)
If you run the engine on your pressure washer for
3-5 minutes without pressing the trigger on the spray
gun, circulating water in the pump can reach
temperatures between 140-145°F. The automatic cool
down system engages at this temperature and cools
the pump by discharging the warm water onto the
ground, preventing internal pump damage.
OWNER'S RESPONSIBILITIES
Follow the hourly or calendar intervals, whichever occurs first.
More frequent service is required when operating in adverse conditions noted below.
MAINTENANCE SCHEDULE
FILL IN DATES AS YOU COMPLETE
REGULAR SERVICE
HOURLY OPERATING
INTERVAL
SERVICE DATES
MAINTENANCE TASK
PRESSURE WASHER
Check/clean water inlet screen
Check hiah pressure hose
Check deteraent hose
Check spray gun and assembly for
leaks
Purae Duma of air and contaminants
Prepare pump for storaqe below 32°F
ENGINE
Check oil level
Chanae enaine oil
Service air cleaner
Service spark Dlua
Service spark arrester
Prepare for storage
1 Clean if clogged. Replace if perforated or torn.
2 Change oil after the first (5) operating hours and every 50 hours or yearly thereafter.
Change sooner when operating under dirty or dusty conditions.
3 Replace more often under dirty or dusty conditions.
PRODUCT SPECIFICATIONS
Pressure Washer Specifications
Pressure...................... 2,100 PSI
FlowRate ..................... 2.0 GPM
Chemical Mix................... Useas directed
Water Supply Temperature ........ Not to exceed 100°F
Engine Specifications
Rated Horsepower................ 5.0 HP
Spark Plug Type:
Resistor ................... Champion RJ-19LM
SetGap To: .................. 0.030inches (0.76mm)
Gasoline Capacity ............... 1.6Quarts
Oil ....................... SAE 30
Before
Each Use
X1
x
x •
X
x
See "Storaqe" on ,aqe 14.
X ........
x_
}) ; ×3
} x
} x
If unit is to remain idle for
longer than 30 days.
GENERAL RECOMMENDATIONS
The pressure washer warranty does not cover items
that have been subjected to operator abuse or
negligence. To receive full value from the warranty,
the operator must maintain pressure washer as
instructed in this manual including proper storage as
detailed in "Storage" on page 14.
Some adjustments will need to be made periodically to
properly maintain your pressure washer.
All service and adjustments should be made at least
once each season. Follow the requirements in the
"Maintenance Schedule" chart above.
NOTE: Once a year you should clean or replace the
spark plug and replace the air filter. A new spark plug
and clean air filter assure proper fuel-air mixture and
help your engine run better and last longer.
10
BEFORE EACH USE
• Check engine oil level.
• Check water inlet screen for damage.
• Check in-line filter for damage.
• Check high pressure hose for leaks.
• Check chemical filters for damage.
• Check gun and nozzle extension assembly for
leaks.
• Purge pump of air and contaminants.
3. Place the in-line filter screen into the threaded end
of the nozzle extension. Direction does not matter.
Push the screen in with the eraser end of a pencil
until it rests flat at the bottom of the opening. Take
care to not bend the screen.
4. Place the o-ring into the recess. Push the o-ring
snugly against the in-line filter screen.
5. Assemble the nozzle extension to the spray gun,
as described earlier in this manual.
Purge Pump of Air and Contaminants
PRESSURE WASHER
MAINTENANCE
Check and Clean Inlet Screen
Examine garden hose inlet screen. Clean if it is
clogged or replace if it is torn.
Check High Pressure Hose
High pressure hoses can develop leaks from wear,
kinking, or abuse. Inspect hose before each use.
Check for cuts, leaks, abrasions, bulging of cover, or
damage or movement of couplings. If any of these
conditions exist, replace hose immediately.
_ AUTION! Never repair a high pressure hose.
Replace with hose that exceeds the maximum
pressure rating of your pressure washer.
Check Gun and Nozzle Extension
Examine hose connection to gun and make sure it is
secure. Test trigger by pressing it and making sure it
springs back into place when you release it. Engage
safety latch and test trigger. You should not be able to
press trigger. Replace gun immediately if it fails any of
these tests.
Check In-Line Filter
Refer to the illustrationand service the in-line filter if it
becomes clogged, as follows:
In-line Filter
Nozzle extension
O-ring
To remove air from the pump, follow these steps:
• Set up the pressure washer as described in the
"Assembling Your Pressure Washer" section and
connect the water supply.
• Pull the trigger on the gun and hold until a steady
stream of water appears.
To remove contaminants from the pump, follow these
steps:
• Set up the pressure washer as described in the
"Assembling Your Pressure Washer" section, and
connect the water supply.
• Remove the nozzle extension from the gun.
• Start the engine according to instructions in "How
To Use Your Pressure Washer" section.
• Pull the trigger on the gun and hold.
• When the water supply is steady and constant,
engage the safety latch and refasten the nozzle
extension.
Nozzle Maintenance
A pulsing sensation felt while squeezing the spray gun
trigger may be caused by excessive pump pressure.
The principal cause of excessive pump pressure is a
nozzle clogged or restricted with foreign materials,
such as dirt, etc. To correct the problem, immediately
clean the nozzle using the tools included with your
pressure washer and follow these instructions:
1. Shut off the engine and turn off the water supply.
2. Remove the nozzle from the end of the nozzle
extension. Separate the nozzle extension from the
spray gun. Twist the nozzle clockwise to the
stream position. Using the supplied 2mm (5/64)
allen wrench, remove the nozzle from the end of
the nozzle extension.
1. Detach nozzle extension from gun and remove
o-ring and screen from nozzle extension. Flush the
screen, gun, and nozzle extension with clean water
to clear debris.
2. If the screen is damaged, the o-ring kit contains a
replacement in-line filter screen and an o-ring. If
undamaged, reuse screen.
\
3. Remove the in-line filter from the other end of the
nozzle extension.
4. Use the wire included in the kit (or a small paper
clip) to free any foreign material clogging or
restricting the nozzle.
11
Insert wire into nozzle and turn back
and forth to clear obstruction.
5. Using a garden hose, remove additional debris by
back flushing water through the nozzle extension.
Back flush between 30 to 60 seconds. Turn the
adjustable nozzle extension to stream spray and
move the nozzle from low to high while flushing.
6. Reinstall the nozzle and in-line filter into the nozzle
extension. Do Not overtighten the nozzle with the
allen wrench.
7. Reconnect the nozzle extension to the spray gun.
8. Reconnect the water supply, turn on the water, and
start the engine.
9. Test the pressure washer by operating with nozzle
in the high and in the low positions.
1 o-ring, yellow, (p/n B2264) for the end of the
high pressure hose.
NOTE: The above two o-rings are close in size.
Please match carefully to assure proper o-ring usage.
• 1 rubber washer, (p/n B2385) for the inside of the
garden hose connector.
• 1 water inlet screen (p/n B2384) for the garden
hose connector.
O-Ring Maintenance
Through the normal operation of your pressure
washer, the o-rings keep the connections of the hoses
and gun tight and leak-free. They may become worn
or damaged with use.
Provided with your pressure washer is an O-Ring
Maintenance Kit which includes replacement o-rings,
rubber washer and water inlet filter. Refer to the
instruction sheet provided in the kit to service your
unit's o-rings. Note that not all of the parts in the kit
will be used on your unit.
Parts in the O-Ring Kit include:
• 1 o-ring, red, (p/n B2726) for the end of the spray
gun connection between gun and nozzle extension.
To remove a worn or damaged O-Ring:
• Use a small flathead screwdriver to get underneath
the o-ring and pry it off.
ENGINE MAINTENANCE
Checking Oil Level
Oil level should be checked prior to each use or at
least every 8 hours of operation. Keep oil level
maintained.
Changing Oil
Change engine oil after the first 5 hours and every
50 hours thereafter. If you are using your pressure
washer under extremely dirty or dusty conditions, or in
extremely hot weather, change oil more often.
_ CAUTION! Avoid prolonged or repeated skincontact with used motor oil. Used motor oil has
been shown to cause skin cancer in certain
laboratory animals. Thoroughly wash exposed
areas with soap and water.
KEEP OUT OF REACH OF CHILDREN. DON'T
POLLUTE. CONSERVE RESOURCES.
RETURN USED OIL TO COLLECTION
CENTERS.
Change oil while engine is still warm from running,
as follows:
• Drain fuel tank by running pressure washer until
fuel tank is empty.
12
Loading...