Craftsman 580752630 Owner’s Manual
Operator'sIVlanual
3000 PSi MAX*
2.7 GPiViMAX
iViodelNo. 580.752630
®
,, Safety
HOURS: IVlon.- Fri. 8 a.rn. to 5 p.m. (CTI
,, Assembly
,, Operation
WARHIHG
Beforeusing this product, readthis
manualand follow all Safety Rules
and Operatinginstructions.
* This pressure washer is rated in accordance to the PressureWasher Manufacturers Association
(PWMA) standard PWI01 (Testing and Rating Performance of Pressure Washers).
* Esta limpiadora a presiOnest_ clasificada conforme a la norma PWl01 (comprobaciOn y clasificaciOn de rendimiento de limpiadoras
a presiOn)de la AsociaciOn defabricantes de bombas a presiOn(Pressure Washer Manufacturers Association, PWMA).
Sears, Roebuckand Co., HoffmanEstates,IL 60179 U.S.A.
Visit our Craftsman website: www.craftsrnan.corn
Part No. 208718GS Draft B (11/04/2009)
Antes de utilizar el producto, lea este
manualy siga todas las Reglasde
Seguridad e Instrucciones de Uso.
ADVERTENCiA
,, Maintenance
,, Parts
,, EspaNol,p. 32
WARRANTY .......................................... 2
REPAIRPROTECTIONAGREEMENT........................ 2
SAFETYRULES...................................... 3-5
FEATURESAND CONTROLS.............................. 6
ASSEMBLY........................................ 7-10
OPERATION....................................... 11-15
SPECIFICATIONS..................................... 16
MAINTENANCE.................................... 17-21
STORAGE........................................ 22-23
TROUBLESHOOTING.................................. 24
REPLACEMENTPARTS.............................. 25-28
NOTES............................................. 29
EMISSIONCONTROLWARRANTY..................... 30-31
ESPANOL......................................... 32-55
HOWTO ORDERPARTS ........................ BACKPAGE
CRAFTSMANLiMiTEDWARRANTY
If this Craftsmanproduct fails due to a defect in material or workmanship within two years from the date of purchase, return it
to anySearsstore, Sears Parts & RepairService Center,or other Craftsmanoutlet in the United Statesfor free repair (or
replacementif repair proves impossible).
This warranty appliesfor only 90 daysfrom the dateof purchase if this product is ever usedfor commercial or rental
purposes.
Thiswarranty coversOHLYdefects in material andworkmanship.Searswill HOTpayfor:
* Expendableitems that canwear out from normal usewithin the warranty period, suchas spray guns, hoses, nozzle
extensions, nozzles,filters and spark plugs.
. Repairsnecessarybecauseof accident, or failure to operateor maintain the product according to all supplied instructions.
. Preventivemaintenance,or repairs necessarydue to improper fuel mixture, contaminated or stalefuel.
This warranty givesyou specific legal rights, and you may also haveother rights which vary from stateto state.
Sears, Roebuck and Co,, Hoffman Estates, IL 60179
Congratulations on making a smart purchase.
Your new Craftsman® product is designed and manufactured
for years of dependableoperation. But like allproducts, it
may requirerepair from time to time. That's when having a
Repair Protection Agreement can saveyou money and
aggravation.
Here'swhat the RepairProtection Agreement* includes:
* Expertservice by our 10,000 professional repair
specialists
* Unlimited serviceand no chargefor parts and labor on
all coveredrepairs
. Product replacementupto $1500 if your covered
product can't be fixed
. Discount of 10% from regular priceof service and related
installed parts not covered by the agreement;also,10%
off regular price of preventivemaintenance check
* Fasthelp byphone-we caii it Rapid Resolution- phone
support from a Sears representative.Think of us as a
"talking owner's manual".
Onceyou purchasethe Repair Protection Agreement, a
simple phonecarlis all it takes for you to schedule service.
You cancall anytimeday or night, or scheduleaservice
appointment online.
The Repair ProtectionAgreement is a risk-free purchase. If
you cancelfor any reasonduring the product warranty
period,we will provide a full refund.Or, a prorated refund
anytime after the product warranty period expires. Purchase
your RepairProtectionAgreement today!
Some limitations and exclusions apply. Forprices and
additional informationin the U.S.A. call 1-800-827-6655.
* Coverage in Canadavaries on someitems. Forfuji
details, caii Sears Canadaat 1-800-361-6665.
SearsInstallation Service
ForSears professional installation of home appliances,
garagedoor openers,water heaters,and other major home
items, inthe U.S.A.or Canadacall 1-S00-4-MY-HOME®.
©2009
Readthis manual carefully and becomefamiliar
with yourpressurewasher. Knowits applications,
itslimitations, and any hazardsinvolved.
important Safety I.formation
Safety Symbolsand Meanings
A. WARNING Theengine exhaust from this product
contains chemicals known to the Stateof California to
cause cancer,birth defects,or other reproductive harm.
A. WARNING This product contains lead and lead
compounds, known to the Stateof Californiato cause
birth defects or other reproductive harm. Washyour
handsafter handling this product.
ToxicFumes Kickback
ElectricalShock
2
SlipperySurface Fall
Fire
Explosion Operator'sManual
ih
MovingParts Flying Objects Hot Surface
,A The safety alertsymbol indicatesapotentialpersonal
injury hazard.A signalword (DANGER,WARNING,or
CAUTION)is usedwith the alert symbol to designatea degree
or levelof hazardseriousness. A safety symbol may be used
to representthe typeof hazard.Thesignal word NOTICEis
usedto addresspractices not relatedto personal injury.
A. DANGERindicatesa hazardwhich, if not avoided, will
result in deathor serious injury.
A. WARNINGindicates a hazardwhich, if not avoided, could
result in deathor serious injury.
A. CAUTIONindicates a hazardwhich, if not avoided, could
result in minor or moderate injury.
NOTICEaddresspractices not relatedto personal injury.
ChemicalBurn
FluidInjection
A. WARNING Runningenginegivesoff carbon
monoxide, an odorless, colorless, poison gas.
_ Breathingcarbon monoxide headache,
fatigue, dizziness,vomiting, confusion, seizures,
nausea,fainting or death.
Some chemicals or detergentsmay beharmful if inhaled
or ingested, causing severenausea,fainting, or
poisoning.
• OperatepressurewasherONLYoutdoors.
• Keepexhaustgasfromenteringa confinedareathrough
windows,doors,ventilationintakes,or otheropenings.
• DONOTstartorrunengineindoorsorinanenclosedarea,
evenifwindowsanddoorsareopen.
• Usearespiratoror maskwheneverthereisachancethat
vaporsmaybeinhaled.
• Readall instructionswith masksoyouarecertainthe maskwill
providethenecessaryprotectionagainstinhalingharmful
vapors.
A. WARNING ChemicalBurn Hazard.
Chemicalscould cause bodily injury, property
damageor death.
• DONOTusecausticliquidwith pressurewasher.
• UseONLYpressurewashersafedetergents/soaps.Followall
manufacturersinstructions.
can cause
A. WARNING Starter cord kickback(rapid retraction) can
result in bodily injury. Kickbackwill pull hand and
,_arm toward enginefaster thanyou can let go.
Broken bones,fractures, bruises, or sprains
could result.
• NEVERpullstarter cord without first relieving spray gun
pressure.
• When starting engine, pull cord slowly until resistance isfelt
andthen pull rapidly to avoid kickback.
• After each starting attempt, where enginefails to run, always
point spray gun insafe direction, pressred button and squeeze
spray gun trigger to releasehigh pressure.
• Firmly graspspray gunwith both hands when using high
pressure sprayto avoid injury when spraygun kicks back.
A. WARNING Risk of electrocution.
"_.dh Contactwith power source can causeelectric
shock or burn.
• NEVERspraynearpowersource.
A. WARNING The high pressure stream of water that
and its underlying tissues, leading to serious
this equipment produces can cut through skin
injury and possible amputation.
Spray gun traps high water pressure, even when engine is
stopped and water is disconnected, which can cause
injury.
• DONOTallow CHILDRENto operatepressure washer.
• NEVERrepairhigh pressure hose.Replaceit.
• NEVERrepairleaking connections with sealantof any kind.
Replaceo-ring or seal.
• NEVERconnect high pressurehose to nozzleextension.
• Keep high pressurehose connectedto pump and spraygun
while system is pressurized.
• ALWAYS pointspray gun in safedirection, press red button
andsqueezespray guntrigger to releasehigh pressure,every
time you stop engine.
• NEVERaim spray gun at people,animals, or plants.
• DO NOTsecure spray gun in open position.
• DO NOTleavespray gun unattendedwhile machine is running.
• NEVERuseaspray gun which does nothave a trigger lock or
trigger guard in placeand in working order.
• Always be certain spray gun, nozzlesand accessoriesare
correctly attached.
A. WARNING Fuel and its vapors are extremely
flammable and explosive.
Fire or explosion can cause severe burns
or death.
WHENADDING OR DRAININGFUEL
* Turn pressurewasher OFFand let it cool at least2 minutes
before removing fuel cap. Loosen capslowly to relievepressure
in tank.
, Fill or drain fuel tank outdoors.
, DONOToverfill tank. Allow spacefor fuel expansion.
, If fuel spills, wait until it evaporatesbeforestarting engine.
, Keepfuel away from sparks, open flames, pilot lights, heat,and
other ignition sources.
, DONOTlight a cigaretteor smoke.
WHENSTARTINGEQUIPMENT
* Ensurespark plug, muffler,fuel cap,and air cleanerare in place.
* DO NOTcrank enginewith spark plug removed.
WHENOPERATINGEQUIPMENT
, DONOTtip engine or equipmentat anglewhich causesfuel to
spill.
, DONOTspray flammable liquids.
WHENTRANSPORTING,MOVINGOR REPAIRINGEQUIPMENT
, Transport/move/repair with fuel tank EMPTYor with fuel shutoff
valveOFF.
, DONOTtip engine or equipmentat anglewhich causesfuel to
spill.
, Disconnectspark plug wire.
WHENSTORINGFUELOR EQUIPMENTWITH FUELIN TANK
* Store awayfrom furnaces, stoves, water heaters,clothes
dryers, or other appliancesthat have pilot light or other ignition
source becausetheycan ignitefuel vapors.
A. WARNING Contact with muffler area can result in
serious burns.
_ _ Exhaust heat/gases can ignite
fuel tank causing a fire.
• DO NOTtouch hot parts and AVOIDhot exhaust gases.
• Allow equipment to cool before touching.
• Keep at least5 feet (152 cm) of clearanceon all sides of
pressure washer including overhead.
• It is aviolation of California Public Resource Code,Section
4442, to use or operate the engine on any forest-covered,
brush-covered, or grass-covered landunless the exhaust
system is equipped with a spark arrester, as defined in Section
4442, maintained in effective working order. Other states or
federaljurisdictions may havesimilar laws.
Contactthe original equipment manufacturer, retailer, or dealer
to obtain a spark arrester designedfor the exhaust system
installed onthis engine.
• Replacement parts must bethe same and installed in the same
position as the original parts.
combustibles, structures or damage
_i, WARNING Use of pressure washer can create
_' Kickback from spray gun can cause you
• Operatepressurewasher from a stable surface.
• The cleaning areashould have adequateslopesand drainageto
reducethe possibility of a fall due to slippery surfaces.
• Be extremely careful if you must usethe pressurewasherfrom
a ladder, scaffolding, orany other similar location.
• Firmly graspspray gunwith both hands when using high
pressure sprayto avoid injury when spraygun kicks back.
A, WARNING Unintentional sparking can result in fire or
WHENADJUSTINGOR MAKINGREPAIRSTO YOURPRESSURE
WASHER
• Disconnect the spark plug wire from the spark plug and place
the wire where it cannot contact spark plug.
WHENTESTINGFORENGINESPARK
• Use approved spark plug tester.
• DONOTcheck for spark with spark plug removed.
puddles and slippery surfaces.
to fall.
_¢ electric shock.
A, WARNING Starter and other rotating parts can
entanglehands, hair, clothing, or accessories.
. NEVERoperatepressurewasherwithoutprotectivehousingor
covers.
. DONOTwearlooseclothing,jewelryor anythingthat maybe
caughtin thestarterorotherrotatingparts.
* Tieuplonghairandremovejewelry.
A, WARNING Riskof eyeinjury.
Spray can splash backor propelobjects.
• Always wear indirect vented (chemical splash) safetygoggles
markedto comply with ANSIZ87.1 when using or in vicinity of
this equipment.
• NEVERsubstitute safetyglasses or dry-condition goggles for
indirect vented safety goggles.
NOTICE High pressure spray may damage fragile items
including glass.
= DONOTpointspraygunatglasswhenusingMAX(0°) nozzle.
= NEVERaimspraygunatplants.
NOTICE Improper treatment of pressure washer can
damage it and shorten its life.
• If you have questions about intended use,ask dealer or contact
Sears.
• NEVERoperate units with broken or missing parts, or without
protective housing or covers.
• DO NOTby-pass any safetydevice on this machine.
• DONOTtamper with governed speed.
• DONOToperate pressure washer above rated pressure.
• DONOTmodify pressure washer in any way.
• Before starting pressure washer in cold weather,check all parts
of the equipment to besure ice has not formed there.
• NEVERmove machine by pulling on hoses. Usehandleprovided
on unit.
• Check fuel system for leaks or signs of deterioration, such as
chafed or spongy hose,loose or missing clamps, or damaged
tank orcap. Correct all defects before operating pressure washer.
• This equipment is designedto be used with Searsauthorized parts
ONLY.If equipment is used with parts that DONOTcomply with
minimum specifications, userassumesall risksand liabilities.
KNOWYOURPRESSUREWASHER
Readthe Operator's Manual and safetyrules before operating your pressurewasher.
Compare the illustrations with your pressure washer to familiarize yourself with the locations of various controls and
adjustments. Save this manual for future reference.
A- Spray Gun-- Controls the application of water onto cleaning
surface with trigger device. Includestrigger lock.
B- PrecisionSprayTM Nozzles-- Max,General,Flush,Jet Soap and
Detergent Nozzles:for various cleaning applications.
C- AccessoryTray-- Provides convenient storagefor accessories,
such as gun, spray tips, etc.
D - ProjectPro® PerfectlVlixTM Siphon -- Mixes concentrate with
pressure washer spray.
E - Bottle Bracket -- Cleaning solution bottle fits in wire form
bracket here.Concentrate bottle not included.
F - Oil Fill/Dipstick -- Check,add and drain engine oil here.
G - Automatic Cool DownSystem-- Cycleswater through pump
when water reaches 125°-155°F. Warm waterwill dischargefrom
pump onto ground. This system prevents internal pump damage.
H - Pump-- Developshigh pressure.
J - DetergentSiphoningTube/Filter-- Useto siphonpressurewasher
safedetergentsinto the low pressurestream.
K- High PressureOutlet-- Connectionfor high pressurehose.
L - Water Inlet -- Connectionfor garden hose.
IVi- Air Filter -- Protects engine byfiltering dust and debris out of
intakeair.
N - Recoil Starter -- Used for starting the engine manually.
P- FuelTank -- Filltank with regular unleadedfuel. Always leave
room for fuel expansion.
R - Fold Down Handle-- Handle and accessory tray fold fiat atop
cold engine for space-saving storage.
S - NozzleExtensionwith QuickConnect -- Allows you to switch
betweenfive different PrecisionSprayTM nozzles.
T - Hose Wrap and High PressureHose-- Hosewrap provides
easytransport and handling of the high pressurehose. Connect
oneend of hoseto water pump and the other end to spray gun.
items Not Shown:
FuelValve -- Usedto turn fuel supply on and off to engine.
Engine Switch -- Sets engine in starting mode for recoil starter and
stops a running engine.
Choke Rod-- Prepares acold enginefor starting.
identificationLabel (near rear of base plate) -- Provides model
and serial number of pressure washer. Pleasehavethese readily
available if callingfor assistance.
Warning/Operating Instructions Tag-- Identifieshazardsand proper
procedureto start/stop pressurewasher.
Your pressurewasherrequires some assembly and is ready
for useonly after it has been properly serviced with the
recommendedoil andfuel.
If you haveany problemswith the assembly of your
pressurewasher, please call the pressurewasher helpline
at 1-800-222-3136.
UNPACKTHEPRESSUREWASHER
1. Removeeverything from carton except pressurewasher,
2. Opencarton completely by cutting eachcorner from top
to bottom.
3. Removepressure washer from carton.
CARTONCONTENTS
Checkall contents. If anyparts are missing or damaged,call
the pressure washer helplineat 1-800-222-3136.
* Main Unit
* Handle
* AccessoryTray
* High PressureHose
* Spray Gun
* NozzleExtensionwith Quick ConnectFitting
* Oil Bottle
* HoseWrap
* DetergentSiphoning Hose/Filter
* Bottle BracketWireform (2)
* PerfectMWMSiphoning Unit/Hose
* Parts Bag(which includes the following):
* Operator's Manual
* Owner's Registration Card
* Bag containing 5 PrecisionSprai MNozzles
* HandleFasteningHardwareKit (whichincludes):
* HandleBolts (2)
* CarriageBolt (2)
* Plastic Knobs for Handle(2)
* Plastic Knob (2)
* TreeClips (4)
Becomefamiliar with eachpiece beforeassembling the
pressure washer. Identify all contents with the illustration on
page 6. if any partsare missing or damaged,call the
pressure washer helpline at1-800-222-3136.
7. Connectwater supply to pump.
8. Attach nozzleextension to spray gun.
9. Select/attach quick connect PrecisionSprai Mnozzleto
nozzleextension.
Attach Handle and Accessory Tray
1. Placehandle(A) onto handle supports (g) connectedto
main unit. Make sure holes (C) in handlealign with holes
(C) on handlesupports.
.
insert handlecarriagebolts (D) through holes from
inside of unit and attach aplastic knob (E) from outside
of unit. Tighten by hand. Byloosening both knobs to the
middle section of the attachmentbolt, the upper handle
canfold forward to store fiat atop the cold engine.
NOTICE
hot.
3.
DONOTfold the handledown while the engine is
Placeaccessory tray (F) over holes (6) on handle
(viewing from backof unit). Pushthe tree clips (H) into
the holes until they sit fiat against the accessory tray.
ASSEMBLINGPRESSUREWASHER
Your Craftsmanpressure washer will needassembly before
operation:
1. Fill out and sendin registration card.
2. Attach handle and accessory tray.
3. Connectdetergent siphon hoseto pump.
4. Add oil to engine crankcase.
5. Add fuel to fuel tank.
6. Connectpressure hose to spray gun and pump.
,
insert multi-colored quick connect nozzlesand other
supplied accessories in spacesprovided in accessory
tray. SeeHow to UseAccessory Tray.
.
Align hosewrap (A) to the back side of accessorytray.
Locate notch with "unlock"icon (B) on hose wrap.
Position notch at top with hose wrap in vertical position.
Clips in the back of accessorytray should slide into the
grooves on the inside surface of hosewrap. Slide hose
wrap on back of accessorytray and rotate 1/8 turn until
"locked"icon (6) is in vertical position. Hosewrap is
easily removed from the accessorytray for wrapping and
unwrapping of the high pressure hose. A clip to secure
the hose on the reel makesit easyto wrap the hose
while it is detachedfrom the accessorytray.
2-1N-1SoapSystem
The pressure washer is equippedwith two detergent
siphoning hoses.
ProjectPro PerfectMixTM Siphon
Bluetube with blue bottle cap:
,._, Whenusing the blue PerfectiViixTMsiphon, use
the PerfectMWMExtremeConcentratestraight
from the bottle.
StandardSiphonTube
Cleartube with filter:
When using the clear siphon tube, dilute
1 part PerfectlViixTMExtremeConcentrate
to 16 parts water (4 ozof concentrate
makes1/2 gallon of mix.)
Attach Project Pro® PerfectMix TM Siphon to
Pump
Attach the hose end of the blue PerfectiVlixTMSiphon (6) to
the barbed hosefitting (I-I)on the pump.
.
Attach bottle brackets (D) to handle with carriage bolts
(E) and black plastic knobs (F). Tighten by hand.
Attach PerfectMix TM Detergent Siphon to
Concentrate BotUe
PlacePerfectMixTMbottle (not included) in the wire-form
bracketon the handle. Removecap from bottle and insert the
PerfectMixTMSiphon (6). Screw the siphon unit to the top of
the bottle (J). Usethe clip on the cap (1{)to snap siphon to
wire form bracket when siphon is not in a concentrate bottle.
AddEngineOil
1. Placepressure washer on a flat, levelsurface.
2. Cleanarea around oil fill and remove yellow oil fill
cap/dipstick.
3. Using oil funnel (optional), slowly pour contents of
provided oil bottle into oil fill opening.
NOTICE Improper treatment of pressure washer can
damage it and shorten its life.
• DO NOTattempt to crank or start the enginebefore it has been
properly servicedwith the recommendedoil. This may result in an
enginefailure.
4. Replaceoil fill cap/dipstick and fully tighten.
1. Useclean, fresh, regular unleadedfuel with a minimum
of 86 octane with equipment. DONOTmix oil with fuel.
2. Placepressurewasher on a levelsurface.Cleanarea
around fuel fill cap, remove cap.
3. Slowly add regularunleadedfuel to bottom of fuel level
limit in neck of fuel tank. Becareful not to overfill.
Add Fuel
A. WARNING Fuelandits vapors areextremely
flammable and explosive.
_._ ire or explosion can causesevere burns
or death.
WHEN ADDINGFUEL
• Turn pressure washerOFFand let it cool at least2 minutes
before removing fuel cap. Loosen capslowly to relieve pressure
in tank.
• Fill fuel tank outdoors.
• DONOToverfill tank. Allow spacefor fuel expansion.
• If fuel spills, wait until it evaporatesbefore starting engine.
• Keepfuel awayfrom sparks, open flames, pilot lights, heat,and
other ignition sources.
• DONOTlight a cigarette orsmoke.
MA×IMUM FUEL LEVEL
.
Install fuel cap and allow any spilled fuel to evaporate
beforestarting engine.
CAUTION!Alcohol-blendedfuels (calledgasohol,ethanol or
methanol) canattract moisture, which leadsto separation and
formation of acids during storage.Acidic gas candamage the
fuel system of an enginewhile in storage.
To avoid engineproblems, the fuel system should be emptied
beforestorage of 30 days or longer. Drain the fuel tank, start
the engineand let it run until the fuel lines andcarburetor are
empty. Usefresh fuel next season. See Storagefor additional
information.
NEVERuse engine or carburetor cleaner products in the fuel
tank as permanent damagemayoccur.
Connect Hose and Water Supply to Pump
NOTICE DONOTrun the pump without the water supply
connectedand turned on.
= Damagetoequipmentresultingfrom failuretofollowthis
instructionwill voidwarranty.
4. Runwater through garden hosefor 30 secondsto flush
it of debris. Turn off water.
NOTICE DONOTsiphon standing water for the water
supply. Use ONLYcold water (less than 100°F).
5. Connectgarden hose(not to exceed50 feet in length) to
water inlet. Tightenby hand.
NOTICE Removeand discard the shipping capsfrom the
pump's high pressure outlet and water inlet before attaching
hoses.
1. Uncoil high pressurehose and attachone endof hoseto
baseof spray gun. Tighten by hand.
_i, WARNING The high pressure stream of water that
and its underlying tissues, leading to serious
this equipment produces can cut through skin
injury and possible amputation.
• NEVERconnect high pressurehose to nozzleextension.
• Keep high pressurehose connectedto pump and spraygun
while system is pressurized.
• Always becertain spray gun, nozzlesandaccessoriesare
correctly attached.
2. Attach other endof high pressure hoseto high pressure
outlet on pump. Tightenby hand.
NOTICE Using a OneWay Valve (vacuum breakeror check
valve) at pump inlet can causepump or inlet connector
damage.
• ThereMUSTbeat leasttenfeetofunrestrictedgardenhose
betweenthepressurewasherinletandanydevice,suchasa
vacuumbreakeror checkvalve.
• Damageto equipment resulting from failure to follow this
instruction will void warranty.
A, WARNING Riskof eyeinjury.
Spray can splash backor propelobjects.
• Always wear indirect vented (chemical splash) safetygoggles
markedto comply with ANSIZ87.1 when using or in vicinity of
this equipment.
• NEVERsubstitute safetyglasses or dry-condition goggles for
indirect vented safety goggles.
6. Turn ONthe water, press red button (B) on the gun and
squeezethe trigger to purgethe pump system of air and
impurities.
.
Beforeconnecting garden hoseto water inlet, inspect
inlet screen (A). Cleanscreen if it contains debris or have
it replacedif damaged.DO NOTrunpressurewasher if
inlet screenis damaged or missing.
Checklist Before Starting Engine
Reviewthe unit to ensureyou haveperformedall of the
following:
1. Besure to read SafetyRulesand Operationsections
before using the pressure washer.
2. Makesure handleis in placeand secure.
3. Checkthat oil has beenaddedto proper levelin engine
crankcase.
4. Add properfuel to fuel tank.
5. Checkfor proper hoseconnections (high pressureand
water supply) andthat there are no kinks, cuts, or
damageto the high pressure hose.
6. Provide proper water supply (not to exceed100%).
10
HOWTOUSEYOURPRESSUREWASHER
If you haveanyproblems operating your pressure washer,
pleasecall the pressure washer helpline at 1-800-222-3136.
PressureWasherLocation
PressureWasherCJearance
_i, WABNING Exhaustheat/gases can ignite
combustibles, structures or damagefuel tank
causing a fire.
* Keepat least5 ft. (152 cm) clearanceon all sides of pressure
washer including overhead.
Placepressure washer outdoors inan area that will not
accumulate deadlyexhaust gas. DONOTplace pressure
washer where exhaust gas (A) could accumulateandenter
inside or be drawn into a potentially occupied building.
Ensureexhaust gas is kept awayfrom any windows, doors,
ventilation intakes, or other openingsthat can allow exhaust
gasto collect in aconfined area. Prevailingwinds and air
currents should betakeninto considerationwhen positioning
_ressurewasher.
_i, WARNING Running enginegives off carbon
monoxide,an odorless, colorless, poisonousgas.
_ Breathing cancause headache,
fatigue, dizziness,vomiting, confusion, seizures,
nausea,fainting or death.
• OperatepressurewasherONLYoutdoors.
• Keepexhaustgasfromenteringa confinedareathrough
windows,doors,ventilationintakes,or otheropenings.
• DONOTstartorrunengineindoorsor in anenclosedarea,
evenifwindowsanddoorsareopen.
carbon monoxide
To Start YourPressureWasher
To start your engine-powered pressurewasherfor the first
time, follow these instructions step-by-step. This information
alsoapplies wheneveryou start the engine after you havelet
the pressure washer sit idle for at leasta day.
1. Placepressurewasher outside nearan water source
capableof supplying water at a flow rate greaterthan
3.7 gallons perminute and nolessthan 20 PSi at
pressurewasher endof garden hose.
2. Checkthat high pressure hose is tightly connected to
spray gun andpump. SeeAssemblyfor illustrations.
3. Makesure unit is in a levelposition.
4. Connectgarden hoseto water inlet on pressurewasher
pump.
NOTICE DONOTrun the pump without the water supply
connectedand turned on.
• Damageto equipmentresultingfromfailureto followthis
instructionwill voidwarranty.
5. Turn ONthe water, pressredbutton onthe gun and
squeezethe trigger to purge the pump system of air and
impurities.
6. Attach nozzleextension to spray gun. Tighten by hand.
,
ChoosePrecisionSprayTM nozzleyou wantto use, pull
backon collar of nozzleextension, insert nozzleand
releasecollar. Tug on nozzleto makesure it is securely in
place.SeeHow to Use PrecisionSpraSMNozzleSystem.
8. Turn fuel valve (B) to "On" position.
ON
11
OFF
9. Pullchokerod(A)to"Closed"position.
Closed
NOTICE Fora warm engine, besure the choke rod(A) is in
the "Open" position.
10. Move engine stop switch (B)to "On" position.
NOTICE Beforestarting the pressurewasher, be sureyou
are wearing safety goggles asdescribed below.
A. WARNING Risk of eyeinjury.
Spraycan splash backor propel objects.
A. WARNING Starter cord kickback (rapid retraction) can
result in bodily injury. Kickback will puff hand and
_,__ arm toward engine faster than you can let go.
Broken bones, fractures, bruises, or sprains
could result.
• NEVERpull starter cord without first relieving spraygun
pressure.
• When starting engine, pull cord slowly until resistance isfelt
andthen pull rapidly to avoid kickback.
• After each starting attempt, where enginefails to run, always
point spray gun in safedirection, pressred button and squeeze
spray gun trigger to releasehigh pressure.
• Firmly graspspray gun with both handswhen using high
pressure sprayto avoid injury when spraygun kicks back.
2. Return recoil starter slowly. DO NOT let rope "snap
back" against starter.
13. When engine starts, slowly move choke rod to "Open"
position as engine warms. If engine falters, move choke
rod to "Closed" position, then to "Open" position.
• Always wear indirect vented(chemical splash) safety goggles
markedto comply with ANSIZ87.1 when using or in vicinity of
this equipment.
• NEVERsubstitute safetyglasses or dry-condition goggles for
indirect vented safety goggles.
1. When starting engine, position yourself as
recommendedand grasp starter grip handle and pull
slowly until you feel someresistance. Then pull rapidly
to start engine.
_i, WARNING The high pressure stream of water that
and its underlying tissues, leading to serious
this equipment produces can cut through skin
injury and possible amputation.
Spray gun traps high water pressure, even when engine is
stopped and water is disconnected, which can cause
injury.
• DONOTallow CHILDRENto operatepressure washer.
• Keep high pressurehose connectedto pump and spraygun
while system is pressurized.
• NEVERaim spraygun at people,animals, or plants.
• DO NOTsecure spray gunin open position.
• DO NOTleavespray gun unattendedwhile machine is running.
• NEVERuse aspray gun which does not have a trigger lock or
trigger guard inplace and in working order.
• Always be certain spray gun, nozzlesandaccessoriesare
correctly attached.
A. WARNING Contact with muffler area can result in
serious burns.
,_ heat/gases can ignite
fuel tank causing a fire.
• DO NOTtouch hot parts and AVOIDhot exhaust gases.
• Allow equipment to cool before touching.
• Keep at least5 feet (152 cm) of clearanceon all sides of
pressure washer including overhead.
• It isa violation of California Public ResourceCode,Section
4442, to use or operate the engine on any forest-covered,
brush-covered, or grass-covered landunlessthe exhaust
system is equippedwith a spark arrester, as defined in Section
4442, maintained ineffective working order. Otherstates or
federaljurisdictions may havesimilar laws.
Contactthe original equipment manufacturer,retailer, or dealer
to obtain a sparkarrester designedfor the exhaustsystem
installed onthis engine.
• Replacementparts must bethe same andinstalled in the same
position as the original parts.
Exhaust
combustibles, structures or damage
12
How to Stop Your Pressure Washer
1. Releasespray guntrigger and let engineidle for two
minutes.
2. Move engine stop switch to "Off" position.
3. ALWAYSpoint spraygun in asafedirection, push red
button and squeezespraygun trigger to releaseretained
high water pressure.
flOTICE Spraygun traps high water pressure, evenwhen
engine is stopped and water is disconnected.
_i, WARNING The high pressurestream of waterthat
and its underlying tissues, leadingto serious
this equipment produces cancut through skin
injury and possible amputation.
Spraygun traps high water pressure,even when engine is
stopped and water is disconnected, which can cause
injury.
• Keephighpressurehoseconnectedto pumpandspraygun
whilesystemispressurized.
• ALWAYSpointspraygunin safedirection,pressredbutton
andsqueezesprayguntriggerto releasehighpressure,every
timeyoustopengine.
How to Use Accessory Tray
The unit is equipped with an accessorytraywith places to
store your spray gun, nozzleextension and quick connect
spray tips. Thereis also adetachablehosewrap at the back
of the accessorytray to hold your highpressure hose.
1. Placenozzleextension in clip on back of accessorytray.
How to Use PrecisionSpray TM Nozzle System
The quick-connect on the nozzJe extension aJJows you to
switch betweenfivedifferent PrecisionSprayTM system
nozzles.PrecisionSprayTM nozzlescan be changed while
pressure washer is running oncespray guntrigger lock is
engaged.
Followthese instructions to changePrecisionSprayTM
nozzles:
1. Pull back coJJar on quick-connect and puJJ current
PrecisionSprayTM nozzleoff. Store PrecisionSprayTM
nozzlesin holder providedon the accessorytray.
_i, WARNING The highpressure stream of water that
this equipment produces can cut through skin
and its underlying tissues, leadingto serious
injury and possible amputation.
• NEVERexchangePrecisionSprayTM nozzleswithoutthetrigger
lockbeingengagedonthespraygun.
• DONOTtwist PrecisionSprayTM nozzleswhilespraying.
.
Select desired PrecisionSprayTM nozzle:
* Select orange general PrecisionSprayTM nozzlefor all
purpose cleaning. Cleansvinyl siding, brick patios,
concrete driveways and other surfaces.
GENERAL
2. Placespray gun through hole on accessorytray on right
side of unit.
3. insert multi-colored PrecisionSprayTM nozzlesin spaces
provided in accessorytray.
4. Wrap high pressure hoseon hosewrap then attach hose
wrap to back of accessorytray.
5. Hook providedon back of accessorytray for safely
storing safety goggles.
Selectred max PrecisionSprayTM nozzlefor maximum
cleaning.Greatfor cleaningstubborn stains,including
grease,tar, wax,and other hard to removestains.
O MAX
Select cyanjet flush PrecisionSprayTM nozzlefor
quick high flow clean up and long reachcleaning of
second story siding andwindows.
JET FLUSH
13
SelectmagentajetsoapPrecisionSprayTM nozzleto
launch soap to second story siding and windows.
JET SOAP
Select black fan soap PrecisionSprayTM nozzlefor
general cleaning. Greatfor applying soap to
vehicles, boats, driveways, decks, andpatios.
FAN SOAP
3. Pull backon collar,insert newPrecisionSprayTM nozzle
and releasecollar.Tug onnozzleto makesureit issecurely
in place.
UsageTips
* For most effective cleaning, keep PrecisionSprayTM nozzle
from 8 to 24 inches (20 to 61 cm) awayfrom cleaning
surface.
* If you get PrecisionSprayTM nozzletoo close, especially
using a high pressure nozzle,you may damagesurface
being cleaned.
* DONOTget closer than 6 inches (15 cm) when cleaning
tires.
2-m-I SoapSystem
_i, WARNING Chemical Burn Hazard.
i_ Chemicalscould cause bodily injury, property
damageor death.
• DONOTusecausticliquidwithpressurewasher.
• UseONLYpressurewashersafedetergents/soaps.Followall
manufacturersinstructions.
CleaningandApplyingDetergentwith the
Project Pro® PerfectMixTM Siphon
To apply undiluted detergent using the blue
PerfectMWMsiphon, follow these steps:
1. Reviewuse of PrecisionSprayTM nozzles.
2. Attach PerfectMWMsiphon hoseto pump
and PerfectMWMconcentratebottle.
NOTICE Contact with the hot muffler can damage detergent
siphoning tube.
• When inserting the siphon into a detergent solution bottle, route
the tube so asto keep it from inadvertently contacting the hot
muffler.
3. Makesure fan soap (black) or jet soap nozzle(magenta)
is installed.
NOTICE Detergentcannot be applied with the high pressure
nozzles(Cyan, Orangeor Red).
4. Makesure garden hoseis connectedto water inlet.
Checkthat high pressure hose is connectedto spray gun
and pump. Turn on water.
NOTICE You must attach all hoses before you start the
engine.
• Starting the engine without all the hoses connected andwithout
the water turned ONwill damagethe pump.
• Damageto equipment resulting from failure to follow this
instruction will void warranty.
5. Start enginefollowing instructions Howto Start Your
Pressure Washer.
6. Apply detergentto a dry surface, starting at lower
portion of areato be washed and work upward, using
long, even, overlapping strokes.
7. Allow detergent to "soakin"for 3-5 minutes before
washing and rinsing. Reapplyas neededto prevent
surfacefrom drying. DO NOTallow detergent to dry on
(prevents streaking).
Cleaningand ApplyingDetergentwith __
the StandardClear Siphon
To apply diluted detergent using the
standard clearsiphon tube, follow these
steps:
1. Reviewuse of PrecisionSprayTM nozzles.
2. Attach clear siphon hoseto barbedfitting on pump.
3. Mix detergentsolution as required by job.
4. Placesmall filter end of clear siphoning tube into
container with diluted solution as describedabove.
NOTICE DONOTinsert standard siphon hose in Extreme
Concentrate.Failure to dilute concentratewill causeexcessive
application and consumption of solution.
NOTICE Makesure the filter is fully submerged in fluid
while applying solution.
NOTICE Contact with the hot muffler can damage detergent
siphoning tube.
• When inserting the siphon into a detergent solution bottle, route
the tube so asto keep it from inadvertently contacting the hot
muffler.
5. Makesure fan soap (black) or jet soap nozzle(magenta)
is installed.
14
NOTICE Detergentcannot be applied with the high pressure
nozzles(Cyan, Orangeor Red).
6. Make sure garden hose is connectedto water inlet.
flush itwith clean water beforestopping the engine,
Checkthat high pressure hose is connected to spray gun
and pump.Turn on water.
NOTICE You must attach all hosesbefore you start the 2.
engine.
* Startingtheenginewithoutallthehosesconnectedandwithout 3.
thewaterturnedONwill damagethepump.
, Damageto equipmentresultingfromfailureto followthis 4.
instructionwill voidwarranty. 5.
.
Start enginefollowing instructions How to Start Your
Pressure Washer.
8.
Apply detergent to a dry surface, starting at lower
portion of areato be washedand work upward, using
long, even,overlapping strokes.
9. Allow detergent to "soak in"for 3-5 minutes before
washing andrinsing. Reapplyas neededto prevent
surfacefrom drying. DO NOTallow detergentto dry on
(prevents streaking).
NOTICE You must flush the detergentsiphoning system
after each use by placingthe filter into a bucket of clean
water, then run the pressure washer in low pressure for 1-2
minutes.
Pressure Washer Rinsing
ForRinsing:
1. Removesoap PrecisionSprayTM nozzlefrom nozzle
extension.
2. Selectand install desiredhigh pressure nozzlefollowing
instructions How to UsePrecisionSprayMNozzleSystem.
3. Keepspray guna safedistance from areayou plan to
spray.
_i, WARNING Kickbackfrom spray gun cancauseyou to
AutomaticCoolDownSystem(Thermal Relief)
the warm water onto the ground.
Cleanin9 Detergent Siphonin9 Tube
If you usedthe cleardetergentsiphoning tube, you must
1. Placedetergent siphoning tube/filter ina bucketfull of
cleanwater.
Removehigh pressure nozzlefrom nozzleextension.
Select and install asoap nozzlefollowing instructions
How to Use PrecisionSprayTMNozzleSystem.
Flushfor 1-2 minutes.
Shut off engine following instructions How to Stop
Pressure Washerandturn off water supply.
6. ALWAYSpoint spray gun in a safe direction push red
button andsqueezespray guntrigger to release retained
high water pressure.
NOTICE Spray guntraps highwater pressure,evenwhen
engine is stopped and water is disconnected.
_i, WARNING The highpressure stream of water that
and its underlying tissues, leadingto serious
this equipment produces can cut through skin
injury and possible amputation.
Spray gun traps high water pressure,evenwhen engineis
stopped and water is disconnected, which can cause
injury.
• Keephighpressurehoseconnectedto pumpandspraygun
whilesystemispressurized.
• ALWAYSpointspraygunin safedirection,pressredbutton
andsqueezesprayguntriggerto releasehighpressure,every
timeyoustopengine.
If you runthe engine on your pressure washer for
3-5 minutes without pressing the trigger on the spraygun,
circulating water in the pump can reachtemperatures above
125°F.The systemengagesto cool the pump by discharging
fall.
• Operatepressurewasherfromastablesurface.
= Beextremelycarefulif youmustusethepressurewasherfrom
a ladder,scaffolding,or anyothersimilarlocation.
= Firmlygraspspraygunwith bothhandswhenusinghigh
pressuresprayto avoidinjurywhenspraygunkicksback.
4. Apply a high pressure spray to asmall areaand then
checksurface for damage, if no damageis found, you
can assume it is okayto continue rinsing.
5. Start attop of areato be rinsed, working down with
same overlapping strokes as you used for cleaning.
15
Pressure Washer Specifications
Max OutletPressure ...................... 3,000 PSI*
Max Flow Rate............................. 2.7 GPM
DetergentMix ........................ Useas directed
Water Supply Temperature .......... Not to exceedIO0°F
Engine Specifications
Bore ............................... 2.7 in. (69 mm)
Stroke ............................. 2.0 in. (50 ram)
Displacement .................... 11.4 cu. in. (187 cc)
Spark Plug
Resistor ............................ NGKBPR6ES
Set GapTo: ........... 0.028-0.031 in (0.70-0.80 mm)
IntakeValve Clearance ........... 0.15 + 0.04 mm (cold)
ExhaustValve Clearance.......... 0.20 + 0.04 mm (cold)
FuelCapacity .................... 0.25 Gallons (0.93 I)
Oil Capacity ...................... 18.56 ft. oz.(0.55 I)
* This pressure washer is rated in accordanceto the
PressureWasher Manufacturers Association (PWMA)
standard PWI01 (Testing and Rating Performance of
PressureWashers).
16
OWHER'SRESPOHSIBILITIES
Follow the hourly or calendarinteHals,whichever occurs
first. More frequentservice is required when operating in
adverseconditions noted below.
* Changeengine oil
* Check/clean water inlet screen'
Checkhigh pressure hose
Checkdetergent siphoning hose
Checkspray gun and assembly for leaks
Cleandebris
Checkengine oil level
GeneralBecommendaUons
Regularmaintenancewill improvethe performanceand
extend the life of the pressure washer. Seeany Searsor
other qualified servicedealer for service.
The pressurewasher warranty does not cover items that
havebeensubjected to operator abuseor negligence. To
receivefull valuefrom the warranty, the operator must
maintain pressure washer as instructed in this manual
including proper storage as detailedin Storage.
Some adjustments will needto be madeperiodically to
properly maintain your pressure washer.
All service and adjustments should be madeat least once
each season. Follow the requirements inthe Maintenance
Schedulechart above.
NOTICE Onceayearyou should cleanor replacethe spark
plug and replacethe air filter. A newspark plug and cleanair
filter assure proper fuel-air mixture and help your engine run
better and last longer.
Cleanengine air cleaner2
Changeengine oiF
Check/adjustspark plug
Inspect muffler and spark arrester
Check/adjustidle speeds
Check/adjustvalve clearances
* Cleanfuel tank & filters
* Cleancombustion chambers
* Replaceengineair cleaner
* Replacespark plug
Checkfuel tubes(Replaceif necessary)
' Cleanif clogged. Replace if perforated or torn.
2Service more often under dirty or dusty conditions.
sThese items should be serviced by your servicing dealer.
Pump Oil
DONOTattempt anyoil maintenanceon this pump. The
pump is pre-iubricated andsealedfrom the factory, requiring
no additional maintenance for the life of the pump.
Emissions Control
Maintenance, replacement,or repair of the emissions
controldevices and systemsmay be performedby any non-
roadengine repair establishment or individual. However,
to obtain "no charge" emissions control service, the work
must be performed by afactory authorizeddealer. Seethe
Emissions Warranty.
Before Each Use
1. Checkengine oil level.
2. Cleandebris.
3. Checkwater inlet screenfor damage.
4. Checkhigh pressure hose for leaks.
5. Checkgun and nozzleextension assemblyfor leaks.
6. Purge pump of air and contaminants.
17
Loading...