Craftsman 536887994 Owner’s Manual

ICRRFTSMRN 1

Operator's Manual

Snow Thrower

9 Horsepower

Electric Start Dual Stage

Model 536.887994

CAUTION: Before using this product,

read this manual and follow all of its Safety Rules and Operating Instructions.

Manual del usario Quitanieves

9 caballos de fuerza (hp)

Biet&pico

Arranque el_ctrico

Modelo 536.887994

PRECAUCION: Antes de usar este producto,

lea este manual y siga todas las reglas de seguridad e instrucciones de operaci6n.

Sears, Roebuck and Co., Hoffman Estates, IL 60179 U.S.A.

F-0310107L www.sears.com/craftsman

nl:l -I ! :llo]i[ilo]l II11lt,

WARRANTY STATEMENT ...... 2

SAFETY RULES ............... 2

INTERNATIONAL SYMBOLS .... 4

ASSEMBLY ................... 6

OPERATION .................. 10

MAINTENANCE ............... 16

SERVICE AND ADJUSTMENT .. 19

iflvh.lztz#:!l i i'it:t f:l d!_viI1 lid

LIMITED TWO-YEAR WARRANTY ON CRAFTSMAN SNOW THROWER

For two years from the date of purchase, when this Craftsman Snow thrower is maintained,

lubricated, and tuned up according to the operating and maintenance instructions in the

owner's manual, Sears will repair, free of charge, any defect in material or workmanship.

If this Craftsman Snow thrower is used for commercial or rental purposes, this warranty ap- plies for only 90 days from the date of purchase.

This warranty does not cover the following:

Items which become worn during normal use, such as spark plugs,drive belts and shear pins.

Repair necessary because of operator abuse or negligence, including bent crankshafts and the failure to maintain the equipment according to the instructions contained in the

owner's manual.

WARRANTY SERVICE IS AVAILABLE BY RETURNING THE CRAFTSMAN SNOW

THROWER TO THE NEAREST SEARS SERVICE CENTER IN THE UNITED STATES. THIS WARRANTY APPLIES ONLY WHILE THIS PRODUCT IS IN USE IN THE UNITED

STATES.

This warranty gives you specific legal rights, and you may also have other rights which may vary from state to state.

Sears, Roebuck and Co., D817WA, Hoffman Estates. [L 60179

STORAGE .................... 29

TROUBLESHOOTING TABLE . .. 30

REPAIR PARTS ............... 34

ENGINE REPAIR PARTS ....... 52

SPANISH (ESPAI%IOL) .......... 61

PARTS ORDERING/SERVICE ..

BACK COVER

_lb OOK FOR THIS SYMBOL TO POINT OUT IMPORTANT SAFETY PRECAUTIONS.

Engine Exhaust, some of its constituents, and certain vehicle components contain or emit chemicals known to the State of California to

cause cancer and birth defects or other repro- ductive harm.

Battery posts, terminals and related accessories contain lead and lead compounds, chemicals

known to the State of California to cause cancer and birth defects or other reproductive harm.

WASH HANDS AFTER HANDLING.

F-0310107L 2

IT MEANS-- ATTENTION!!! BECOME ALERT!!! YOUR SAFETY IS INVOLVED.

_i WARNING: Always discon-

IMPORTANT: Safety standards re-

quire operator presence controls to

minimize the risk of injury. Your snow

thrower is equipped with such controls.

Do not attempt to defeat the function of the operator presence control under any circumstances.

nect the spark plug wire and place it where it cannot

make contact with spark plug to prevent accidental starting during:

Preparation, Maintenance, or Stor- age of your snow thrower.

TRAINING

1. Read this operating and service instruction manual carefully. Be thoroughly familiar

with the controls and the proper use of the snow thrower. Know how to stop the snow thrower and disengage the controls quick-

2. Never allow children to operate the snow thrower. Never allow adults to operate the

snow thrower without proper instruction.

3. Keep the area of operation clear of all per- sons, particularly small children and pets.

4. Exercise caution to avoid slipping or falling especially when operating in reverse.

PREPARATION

1. Thoroughly inspect the area where the snow thrower is to be used and remove all

doormats, sleds, boards, wires, and other foreign objects.

2. Disengage all clutches before starting the engine (motor).

3. Do not operate the snow thrower without wearing adequate winter outer garments. Wear footwear that will improve footing on slippery surfaces.

4. Handle fuel with care; it is highly flam- mable.

a. Use an approved fuel container. b. Never remove fuel tank cap or add fuel

to a running engine (motor) or hot en- gine (motor).

c. Fill fuel tank outdoors with extreme

care. Never fill fuel tank indoors.

d. Replace fuel cap securely and wipe up

spilled fuel.

e. Never store fuel or snow thrower with

fuel in the tank inside of a building where fumes may reach an open flame

or spark.

f. Check fuel supply before each use, al-

lowing space for expansion as the heat of the engine (motor) and/or sun can

cause fuel to expand.

5. For all snow throwers with electric starting motors use electric starting extension cords cartified CSA!UL. Use only with a re- ceptacle that has been installed in accord- ance with local inspection authorities.

6. Never attempt to make any adjustments while the engine (motor) is running (except when specifically recommended by manu- facturer).

7. Let engine (motor) and snow thrower ad- just to o_door temperatures before starting

to clear snow.

F-0310107L

Always wear safety glasses or eye shields during operation or while performing an ad- justment or repair to protect eyes from foreign objects that may be thrown from the

snow thrower.

OPERATION

1. Do not operate thissnow thrower ifyou are taking drugs or other medication which can

cause drowsiness or affect your ability to operate this snow thrower.

2. Do not use the snow thrower if you are mentally or physically unable to operate the

snow thrower safely.

3. Do not put hands or feet near or under ro- tating parts. Keep clear of the discharge

opening at all times.

4. Exercise extreme caution when operating on or crossing gravel drives, walks or

roads. Stay alert for hidden hazards or traffic.

5. After striking a foreign object, stop the en- gine (motor), remove the wire from the

spark plug, thoroughly inspect snow thrower for any damage, and repair the damage before restarting and operating

the snow thrower.

6. If the snow thrower should start to vibrate abnormally, stop the engine (motor) and

check immediately for the cause. Vibration is generally a warning of trouble.

7. Stop the engine (motor) whenever you leave the operating position, before un- clogging the anger/impeller housing or dis- charge chute and when making any

repaire, adjustments, or inspections.

8. When cleaning, repairing, or inspecting, make certain the augedimpeller and all moving parts have stopped and all controls

are disengaged. Disconnect the spark plug wire and keep the wire away from the spark plug to prevent accidental starting.

9. Take all possible precautions when leaving the snow thrower unattended. Disengage

the auger/ impeller, stop engine (motor), and remove key.

10. Do not run the engine (motor) indoors, ex- cept when starting the engine (motor) and

for transporting the snow thrower in or out of_qe building. Open the outside doors; ex-

haust fumes are dangerous (containing CARBON MONOXIDE, an ODORLESS and DEADLY GAS).

11. Do not clear snow across the face of slopes. Exercise extreme caution when changing direction on slopes. Do not at- tempt to clear steep slopes.

12. Never operate the snow thrower without proper guards, plates or other safety pro- tective devices in place.

13.Neveroperatethesnowthrowernearen- closures,automobiles,windowwalls,drop- offs,andthelikewithoutproperadjustment

MAINTENANCE AND STORAGE

1. Check shear bolts and other bolts at fre_

ofthesnowdischargeangle.Keepchildren andpetsaway.

14.Donotoverloadthesnowthrowercapacity byattemptingtoclearsnowattoofasta

rate.

2. Never store the snow thrower with fuel in

15.Neveroperatethesnowthrowerathigh transportspeedsonslipperysurfaces.

Lookbehindandusecarewhenbacking up.

3. Always refer to operator's guide instruc-

16.Neverdirectdischargeatbystandersor allowanyoneinfrontofthesnowthrower.

17.Disengagepowertothecollector/impeller whensnowthroweristransportedornotin

4. Maintain or replace safety and instruction

use.

18.Useonlyattachmentsaedaccessoriesap-

5. Run the snow thrower a few minutes after

provedbythemanufacturerofthesnow thrower(suchastirechains,electricstart kits,ect.).

19. Never operate the snow thrower without good visibility or light. Always be sure of

your footing and keep a firm hold on the handles. Walk;never run.

20. Do not over-reach. Keep proper footing and balance at all times.

21. Do not attempt to use snow thrower on a roof.

_ WARNING: This snow thrower isfor use on sidewalks, driveways

Caution should be exercised while using on steep sloping surfaces. DO NOT USE

SNOW THROWER ON SURFACES ABOVE GROUND LEVEL such as roofs of resi- dences, garages, porches or other such

structures or buildings.

quent intervals for proper tightness to be sure the snow thrower is in safe working

condition.

the tank inside a building where ignition sources are present such as hot water and space heaters, clothes dryers, and the like. Allow the engine (motor) to cool before

storing in any enclosure.

tions for important details if the snow thrower is to be stored for an extended

period.

labels, as necessary.

throwing snow to prevent freeze-up of the auger/impeller.

and other ground level surfaces.

IMPORTANT: Many of the following symbols are located on your snow thrower or on litera- ture supplied with the product. Before you operate the snow thrower, learn and understand

the purpose for each symbol.

CONTROL AND OPERATING SYMBOLS

Slow Fast

Electric Start Engine Start Engine Run

I I-I N

Engine Off Engine Stop

On Choke Off Choke On Neutral

V,4 =-- G G

Throttle Primer Button Ignition Key

F-0310107L 4

Ignition Off Ignition On

Drive Clutch Forward Reverse

Auger Clutch Auger Collector Engage

Push To Engage Fuel

Electric Starter

Discharge DOWN Discharge UP Discharge LEFT Discharge RIGHT

Weight Transfer Weight Transfer Transmission Ignition Key

Lift Handle To Depress Pedal Insert To Run,

Engage To Disengage Pull Out To Stop.

Oil Fuel Oil Mixture

Safety Warning Symbols

DANGER

Thrown Objects.

Keep Bystanders Away.

DANGER

Thrown Objects.

Keep Bystanders Away.

WARNING

IMPORTANT

Read Owner's Manual

Before Operating

This Machine.

WARNING

Hot Surface

F-O310107L 5

DANGER

Avoid Injury From

Rotating Auger. Keep

Hands, Feet And

Clothing Away.

DANGER

Stop The Engine

Before Unclogging

Discharge Chute!

STOP

,F_,,"I-,,9_ tvAI:] I_'d

CONTENTS OF PARTS BAG (ACTUAL SIZE)

1 - Owner's Manual (not shown) 1 - Packet of Fuel Stabilizer (not shown)

1 - Warranty Card (not shown)

*Non-Assembly Parts,foundintoolboxlocatedon beltcover

PARTS PACKED SEPARATELY IN CARTON

(NOT SHOWN FULL SIZE)

2- Ignition Keys (Attached to engine in plastic bag)

F-0310107L 6

_ ARNING: Always wear

safety glasses or eye shields while assembling snow

thrower.

TOOLS REQUIRED FOR ASSEMBLY

1 - Knife to cut carton

2 - 1/2 inch wrenches

(or adjustable wrenches)

2 - 9/16 inch wrenches

(or adjustable wrenches)

2 - 3/4 inch wrenches

(or adjustable wrenches)

1 -Pliers (to spread cotter pin)

1 - Screwdriver 1 - Measuring tape or ruler

Figure 2 shows the snow thrower com- pletely assembled,

References to the right or left hand side

of the snow thrower are from the view-

point of the operator's position behind the unit,

Auger Drive Lever {,_ Traction

Drive Lever

Shifter

• Crank Assembly

Deflector

Height Adjust

Skid

Figure 1

Figure 1 shows the snow thrower in the

shipping position.

TO REMOVE SNOW THROWER

FROM CARTON

1, Locate all parts packed separately

and remove from the carton. NOTE: Place fuel stabilizer in a

safe place until needed for storage,

2, Remove and discard the packing

material from around the snow thrower.

3. Cut down all four corners of the car- ton and lay the panels flat.

4. For shipping purposes, the height

adjust skids are attached to the pallet. Remove the screw that se-

F-0310107L

Figure 2

cures each height adjust skid to the pallet. See Figure 2.

5. Roll snow thrower off the pallet by pulling on the lower handle. CAU-

TION: DO NOT back over control cables.

6. Remove all packing material from the unit.

7. Cut ties securing the dutch controt

cable to the lower handle and lay cable back away from the motor

frame.

,F_,,"I-,,9_ tvAI:] I_'d

TO ASSEMBLE THE HANDLE AND CRANK ASSEMBLY

1. Cut tie holding shift rod to lower handle and move shifter to the first

forward gear.

2. Cut and discard the plastic tie that secures the crank assembly.

3. Loosen, but do not remove, the screws, flatwashers, Iockwashers, and hex nuts in the upper holes of

the lower handle. See Figure 3.

4. Remove the fasteners and the eye- bolt from the lower holes of the low-

er handle See Figure 5.

RightHand Side Of U

Loosen, but do not remove

11/32"

Flatwasher

5/16" Screw

Figure 3

NOTE: Make sure the cables are not caught between the upper and

lower handle.

5. Raise the upper handle into operat- ing position.

NOTE: If the cables have become dis- connected form the drive levers, rein- stall the cables as shown in Figure 4.

6. Install the fasteners that were re- moved in step 4. DO NOT tighten

until all bolts are in place.

Left Side Of _\ Upper Handle

3/8" Nylon

Eye Bolt Flatwasher

Figure 5

7. Attach the crank rod to the universal

joint assembly with the hair pin. See

Figure 6.

8. Tighten nut on eye bolt. Make sure eye bolt is properly aligned and the

crank can freely rotate.

9. Tighten all handle bolts.

Lever

"Z" Fitting

Control Cable Figure 4

F-O310107L 8

Cran_ _od

Figure 6

,F_,,"I-,,9_ tvAI:] I_'d

NOTE: If the cables have become dis- connected, connect cables as shown in

Figure 7.

Traction Drive Cable Auger Drive Cable

Figure 7

HOW TO SET THE SKID HEIGHT

Your snow thrower is equipped with height adjust skids on the outside of the

auger housing. To adjust the skid

height for different conditions, see To

Adjust Skid Height paragraph in the

Service And Adjustment section.

HOW TO SET THE LENGTH OF THE CABLES

The cables were adjusted at the factory and no adjustments should be neces-

sary. However, after the handles are put in the operating position, the cables can

_- CHECKLIST

Before you operate your new snow thrower, to ensure that you receive the best performance and satisfaction from

this quality product, please review the following checklist:

_" All assembly instructions have been

completed. _" The discharge chute rotates freely. _" No remaining loose parts in carton.

_" Check the fasteners. Make sure all

fasteners are tight.

_" On electric start models, the unit was

shipped with the starter cord plugged

into the engine. Before operating, un-

plug the starter cord from the engine.

be too tight or too loose. If an adjust- ment is necessary, see "How To Check

And Adjust The Cables" in the Service And Adjustment section.

While learning how to use your snow thrower, pay extra attention to the fol-

lowing important items:

_" Engine oil is at proper level. _" Make sure gas tank isfilled properly

with clean, fresh, unleaded gasoline.

_" Become familiar with all controls-

their location and function. Operate

controls before starting engine.

F-0310107L 9

[el ".]_=;ralilJell3

KNOW YOUR SNOW THROWER

READ THIS OWNER'S MANUAL AND SAFETY RULES BEFORE OPERATING YOUR SNOW THROWER. Compare the illustrations with your SNOW THROWER to familiarize yourself with the location of various controls and adjustments. Save

this manual for future reference,

Electric Auger Start Drive Lever Button (right hand)

Primer

Ignition Switch Crank

Gas

Tank

Choke Control Recoil

Throttle Starter

Control Handle

Auger Drive Lever - Starts and stops the auger and impeller (snow gathering

and throwing) Traction Drive Lever - Propels the

snow thrower forward and in reverse. Speed Shifter Lever - Selects the

speed of the snow thrower (6 speeds for- ward and 2 speeds reverse).

Crank Assembly - Changes the direc- tion of snow throwing through the dis- charge chute,

Chute Deflector - Changes the distance the snow is thrown.

Discharge Chute - Changes the height and direction the snow is thrown,

Height Adjust Skid - Adjusts the ground clearance of the anger housing,

Ignition Key - Must be inserted to start the engine.

F-0310107L 10

Height

Adjust Shear Pin Skid Scraper Bar Figure 8

Recoil Starter Handle - Starts the en-

gine manually. Choke Control - Used to start a cold

engine.

Primer Button - Injectsfuel directly into

the carburetor manifold for fast starts in cold weather,

Throttle Control - Controls the engine speed,

Electric Start Button - (if so equipped) Used to start the engine using the 120 V

electric starter,

Shear Pin -Shear pins are designed to break (to protect the machine) if an ob-

iect becomes lodged in the auger hous-

ing,

Toolbox - Spare shear pins and spacers are located in toolbox,

(left hand)

Assembly

Chute Deflector

Discharge Chute

Theoperationofanysnowthrowercan resultinforeignobjectsbeingthrown intotheeyes,whichcanresultinse- vereeyedamage.Alwayswearsafety glassesoreyeshieldswhileoperating

thesnowthrower. Werecommendstandardsafety

glassesora wide vision safety mask for

over your glasses.

i_ WARNING: Read Owner's

charge toward bystanders. Stop the engine before unclogging discharge

chute or auger housing and before leaving the machine.

TO STOP YOUR SNOW THROWER

1. To stop throwing snow, release the

2. To stop the wheels, release the

3. To stop the engine, push the

TO CONTROL SNOW DISCHARGE

1. Turn the chute control rod to set the

2. Loosen the wing knob on the chute

Manual before operating machine. Never direct dis-

auger drive lever.

traction drive lever,

throttle control lever to off and pull out the ignition key.

direction of the snow throwing.

deflector and move the deflector to set the distance. Move the deflector

(Up) for more distance, (Down) for less distance. Then tighten the

wing knob (See Figure 9).

the speed you desire by moving the

speed shifter lever left into the ap- propriate notches on the shift lever plate:

Speeds 1.2 - Wet, Heavy Speed 3 - Light

Speed 4 - Very Light Speed 5,6 - Transport only

Engage the traction drive lever (left hand), As the snow thrower starts

to move, maintain a firm hold on the

handles, and guide the snow throw- er along the clearing path. Do not

attempt to push the snow thrower.

3. To move the snow thrower back- ward, move the speed shifter lever

right into first or second reverse and engage the traction drive lever (left

hand),

IMPORTANT: Do not move the speed

shifter lever while the traction lever

is down.

TO THROW SNOW

1. Push down the auger driver lever

(right hand),

2. Release to stop throwing snow.

TO USE WHEEL LOCKOUT PIN

The right hand wheel is secured to the axle with a klick pin. This unit was shipped with this klick pin in the

locked position (through wheel hole). See Figure 10.

Figure g

HOW TO MOVE FORWARD AND BACKWARD

1. To shift, release the traction drive lever (left hand) and move the Locked

speed shifter lever to the speed you Position desire. Ground speed is deter-

mined by snow conditions. Select

F-0310107L 11

Klick Pin

2-Wheel Drive

Figure 10

Ill ".]_ l;rz_lil[i]_j

2. For ease of maneuverability in light snow conditions, disconnect the klick pin from the wheel locked position and push into the single

wheel drive position (unlocked axle

hole only). See Figure 11.

Figure 11

NOTE: Make sure that the klick pin is in the single wheel drive position of the

axle only and not through the locked position.

BEFORE STARTING THE ENGINE

1. Before you service or start the en- gine, familiarize yourself with the

snow thrower. Be sure you under- stand the function and location of all

controls.

2. Check the tension of clutch cable before starting the engine. See To

Adjust The Control Cable para- graph in the Service & Adjust-

ments section of this manual,

3, Be sure that all fasteners are tight, 4, Make sure the height adjust skids

are properly adjusted. See To Ad-

just Skid Height paragraph in the

Service & Adjustments section of

this manual.

5, Checktire pressure (14-17

pounds). Do not exceed maximum amount of pressure,

CHECK THE OIL: NOTE: The engine was shipped from

the factory filled with oil. Check the lev- el of the oil. Add oil as needed.

To Add Oil

1. Make sure the unit is level. NOTE: Do not check the level of the

oil while the engine runs.

F-O3tOIO7L

2. Remove the oil fill cap/dipstick. Check the oil.

3. If necessary, add oil until the oil reaches the FULL mark on the oil fill

cap/dipstick (see Figure 12). Do not add too much oil.

OII FillC._p/Dipstick

-_'_1 NOTE: Oil level 9 must be between

mark Figure 12

4. Tighten the fill cap/dipstick securely each time you check the oil level.

NOTE: S.A.E. 5W30 motor oil may be used to make starting easier in areas

where temperature is consistently 20°R or lower.

FILL GAS:

The engine is certified to comply with California and US EPA emission regula- tions for ULGE (Utility or Lawn and Gar-

den Equipment) engines. ULGE engines are certified to operate on reg-

ular unleaded gasoline.

,_ WARNING: Alcohol blended methanol) can attract moisture

which leads to separation and formation of acids during storage. Acidic gas can damage the fuel sys-

tem of an engine while in storage.

NOTE: To avoid engine problems, the

fuel system must be emptied before storage for 30 days or longer. Start the engine and let it run until the fuel lines

and carburetor are empty. Use fresh fuel next season. See the Storage

section in this manual for additional in- formation.

Never use engine or carburetor cleaner products in the fuel tank or permanent

damage may occur

fuels (called gasohol or

those using ethanol or

Ill ".]_l;ralil [i]_3

Fill the fuel tank only with a fresh, clean, unleaded regular, unleaded pre- mium, or reformulated automotive gas- oline. DO NOT use leaded gasoline.

Make sure that the container you pour the gasoline from is clean and free from rust or other foreign particles. Never

use gasoline that may be stale from long periods of storage in the container.

_ ARNING: Gasoline is flam-

gasoline.

• Do not fill fuel tank while snow

• Keep away from open flame or an

• Never fill the tank completely. Fill

• Always fill fuel tank outdoors and

• Make sure to wipe up any spilled

• Store gasoline in a clean, ap-

TO STOP ENGINE

To stop engine, move the throttle con- trol lever to "STOP" position and re- move key. Keep the key in a safe place. The engine will not start without the key.

TO START ENGINE

Be sure that the engine has sufficient oil. The snow thrower engine is equipped with a 120 volt A.C. electric

starter and recoil starten Before start- ing the engine, be certain that you have

read the following information.

F-O310107L

mable. Always use caution when handling or storing

thrower is running, when it is hot, or when snow thrower is in an en- closed area.

electrical spark and do not smoke while filling the fuel tank.

the tank to within 1/4"-1/2" from the top to provide space for ex-

pansion of fuel.

use a funnel or spout to prevent spilling.

fuel before stating the engine.

proved container and keep the cap in place on the container.

_ ARNING: The starter is

designed to operate on 120 volt AC

household current. It must be prop- erty grounded at all times to avoid the possibility of electrical shock which may be injurious to operator.

• Follow all instructions carefully

• Determine that your house wiring

• If your system is grounded and a

• When connecting 120 volt AC

How To Start A Cold Engine

1. Be sure auger drive and traction

2. Move throttle control to "FAST"

3. Insert the ignition key into the igni-

4. Rotate choke knob clockwise to the

5. (Electric Start) Plug the power cord

equipped with a three-wire power cord and plug and is

as set forth in the "To Start En- gine" section.

is a three-wire grounded system.

Ask a licensed electrician if you are not sure. If your house wire

system is not a three*wire system, do not use this electric starter un-

der any conditions.

three-hole receptacle is not avail* able at the point your starter will

normally be used, one should be installed by a licensed electrician.

"Power Cord", always connect the

cord to the Switch Box on the en- gine first, then plug the other end

into the three*hole grounded re-

ceptacle. When disconnecting

"Power Cord", always unplug the

end in the three*hole grounded re- ceptacle first.

drive levers are in the disengaged (RELEASED) position.

position.

tion slot. Make sure it snaps into

place, Do not turn key.

choke ON position.

intothe switch box on the engine.

Plug the other end of power cord into a three-hole, grounded 120

VOLT, AC receptacle.

[e] ".]_ =;rz_lil[e]_3

6. Push the primer button as speci- fied below. Remove finger from

primer button between pushes.

Do not push if temperature above 50° F (10° C).

Push two times if temperature is 50° F (10° C) to 15°F (-10° C).

Push four times if temperature is below 15° F (-10 ° C).

Push five times if temperature is below0 ° F (-18 ° C).

7. (Electric Start) Push down on the

starter button until the engine starts. Do not crank for more than

10 seconds at a time. This electric starter is thermally protected. If

overheated it will stop automatically

and can be restarted only when it has cooled to a safe temperature (a

wait of about 5 to 10 minutes is re-

quired).

8. (Recoil Start) Rapidly pull the re-

coil starter handle. Do not allow

the recoil starter handle to snap

back. Slowly return the recoil start-

er handle.

9. If the engine does not start in 5 or 6 tries, See Difficult Starting in the

"Troubleshooting Table".

10. When the engine starts, move the choke control to "1/2 choke" posi-

tion. When engine runs smoothly,

move choke control to the off Position.

11. (Electric Start) First disconnect power cord from receptacle. Then,

disconnect the power cord from the

switch box.

12. Run engine at full throttle "FAST"

when throwing snow.

Allow the engine to warm up for several minutes before blowing snow in temper-

atures below 0°F.

How To Start A Warm Engine

if restarting a warm engine after a short

shutdown, leave the choke lever in the off position and do not push the primer

button. If the engine fails to start, follow

the Cold Start instructions.

FROZEN STARTER

if the starter is frozen and will not turn

engine:

1. Pull as much rope out of the starter as possible.

2. Release the starter handle and let it snap back against the starter. Re-

peat until the engine starts.

To help prevent possible freeze-up of

recoil starter and engine controls, pro-

ceed as follows after each snow remov- al job.

1. With the engine running, pull the starter rope hard with a continuous

full arm stroke three or four times.

Pulling of starter rope will produce a loud clattering sound. This is not harmful to the engine or starter.

2. With the engine not running, wipe all snow and moisture from the carbu-

retor cover in area of control levers.

Also move throttle control, choke

control, and starter handle several

times.

_IL ARNING: Never run en-

gine exhaust contains CARBON

MONOXIDE, AN ODORLESS AND DEADLY GAS. Keep hands, feet,

hair and loose clothing away from any moving parts on engine and snow thrower.

• The temperature of muffler and

* DO NOT allow children or young

gine indoors or in enclosed, poorly ventilated areas. En*

nearby areas may exceed 150°F.

Avoid these areas.

teenagers to operate or be near snow thrower while it is operat*

ing.

F-0310107L 14

TO REMOVE SNOW FROM AUGER

_b WARNING: Do not attempt

auger without taking the following precautions:

A cleaning stick is attached to the top of the auger housing, Use the cleaning

to remove snow or debris that may become lodged in

stick to remove snow from the auger

housing.

Release auger drive lever. Move throttle lever to stop position. Remove (do not turn) ignition key. Disconnect spark plug wire. Do not place your hands in the au-

ger or discharge chute. Use the

cleaning stick to remove snow.

SNOW THROWING TIPS

1. For maximum snow thrower efficien- cy in removing snow, adjust ground

speed, NEVERthe throttle. Go slower in deep, freezing or wet snow. If the wheels slips, reduce

forward speed. The engine is de-

signed to deliver maximum perfor- mance at full throttle and should be

run at this power setting at all times.

2. Most efficient snow throwing is ac- complished when the snow is re- moved immediately after if falls.

3. For complete snow removal, slightly

overlap each path previously taken.

4. The snow should be discharged down wind whenever possible.

5. For normal usage, set the skids so

that the scraper bar is 1/8" above the skids. For extremely hard-

packed snow surfaces, adjust the

skids upward so that the scraper bar touches the ground.

6. On gravel or crushed rock surfaces, set the skids at 1-1/4" below the

scraper bar. See To Adjust Skid Height paragraph in the Service &

Adjustments section of this manu-

al. Rocks and gravel must not be picked up and thrown by the ma-

chine.

7. After the snow throwing job has been completed, allow the engine to idle for a few minutes, which will

melt snow and accumulated ice off

the engine.

8. Clean the snow thrower thoroughly after each use.

g. Remove ice and snow accumulation

and all debris from the entire snow

thrower, and flush with water (if pos-

sible) to remove all salt or other chemicals. Wipe snow thrower dry.

F-0310107L 15

SERVICERECORDS

Fillindatesasyou Before Every Every Every

completeregular Each 5 10 25 Each Betore SERVICE

service. Use Often Hours Hours Hours Season Stcrage DATES

Chain Lubrication

Change Engine Oil _/ _/

Remove Fuel _/

* Adjust after 2 to 4 hours of use,

GENERAL RECOMMENDATIONS The warranty on this snow thrower

does not cover items that have been subjected to operator abuse or negli- gence. To receive full value from the

warranty, the operator must maintain the snow thrower as instructed in this

manual, Some adjustments will need to be

made periodically to properly maintain your snow thrower.

F-0310107L 16

AFTER EACH USE

Run the machine to clear the auger of snow.

To prevent freezing of the auger or controls, remove all snow and slush

from the snow thrower.

Check for any loose or damaged parts. Tighten any loose fasteners. Check and maintain the auger. Check controls to make sure they

are functioning properly. If any parts are worn or damaged,

replace immediately.

PRODUCT SPECIFICATIONS

HORSEPOWER 9 HP

DISPLACEMENT 19.34cu.in.

GASOLINE 4 quarts CAPACITY (unleaded)

OIL CAPACITY 5W30

(20 oz capacity)

PARK PLUG: Champion RJ19LM

VALVE CLEARANCE: Intake: ,010 In,

(Gap .030 in.) or equivalent

Exhaust: .010 In.

SNOW THROWER

AUGER DRIVE BELT

Adjust the auger drive belt after the first 2 to 4 hours of use, again about mid-

season and twice each season thereaf- ter (See to "Belt Adjustment" in the

Service and Adjustment section). CHAIN LUBRICATION

EVERY 25 HOURS

1. Position speed selector lever in first (1) forward gear.

2. Stand the snow blower up on the auger housing end.

NOTE: When the crank case if

filled with oil, do not leave the

snow blower standing up on the auger housing for an extended period of time.

3. Remove the bottom panel.

4. Lubricate the chains with a chain

type lubricant.

5. For storage, wipe the hexshaft and sprockets with 5W30 motor oil.

NOTE: Clean all excess grease or oil found on the rubber friction

wheel or the disc drive plate.

CAUTION: Do not allow grease or

oil to contact the rubber friction

wheel or the disc drive plate.

6, Install the bottom panel,

F-0310107L

Hexshaff

Figure 13

AUGER GEAR BOX The auger gear box is lubricated at the

factory and should not require addition- al lubrication. If for some reason the

lubricant should leak out, have auger

gear case checked by a competent re-

pairman.

ENGINE

LUBRICATION

Check the crankcase oil level before starting the engine and after each five

(S) hours of continuous use. See

Figure 14. Add S.A.E. 5W30 motor oil as needed. Tighten fill cap/dipstick se- curely each time you check the oil lev- el.

Oil Fill Cap/Dis_

_re 14

Change the oil every twenty-five (25)

hours or at least once a year if the snow thrower is not used for twenty- five (25) hours.

TO CHANGE ENGINE OIL

1. Position the snow thrower so that the oil drain plug is at the lowest

point on the engine.

2. Remove the oil drain plug and the oil fill cap/dipstick. Drain the oil

into a suitable container.

NOTE: The oil will drain more freely

when the engine is warm.

3. After draining all the oil, reinstall the oil drain plug securely.

4. Fill the engine crankcase with

S.A.E. 5W30 motor oil, pouring slowly. DO NOT OVERFILL. See

"To Add Oil" in the Operation Sec-

tion.

SPARK PLUG

Check the spark plug every twenty- five (25) hours. Replace the spark plug

if the electrodes are pitted or burned or if the porcelain is cracked.

1, Make sure the spark plug is clean,

Clean the spark plug by carefully scraping the electrodes (do not

sand blast or use a wire brush),

2, Check the spark plug gap with a

feeler gauge and reset gap to 0,30"

if necessary. See Figure 15,

3. Before installing the spark plug, coat the threads lightly with oil for

easy removal. Tighten the spark plug to a torque of 15 foot-pounds.

FeelerGauge

0.030"

Spark Plug

Figure 15

F-0310107L 18

_hb ARNING: Always discon*

make contact with spark plug to pre- vent accidental starting when mak-

ing any adjustments or repairs.

nect the spark plug wire and place it where it cannot

TO ADJUST SKID HEIGHT

This snow thrower is equipped with two

height adjustment skids, located on the outside of the auger housing. See

Figure 16. These skids elevate the front of the snow throwen

raise the adjustable skids. Tighten

the mounting nuts. See Figure 16.

NOTE: For rocky or uneven surfaces, raise the front of the snow thrower by

moving the skids down.

_IL ARNING: Be certain to

area to be cleared. Objects such as gravel, rocks or other debris, if

struck by the impeller, may be thrown with sufficient force to cause

personal injury, property damage or

damage to the snow thrower.

maintain proper ground clearance for your particular

Nuts

Auger t- Height Adjust Skid

Figure 16

For normal hard surfaces, such as a paved driveway or walk, adjust the

skids as follows.

1. Position the snow thrower on a level surface.

2. Make sure both tires are equally in- flated. Proper tire pressure is 14 to

17 PSI. See side of tire for maxi- mum inflation. Do not exceed maxi-

mum sidewall pressure on tire.

3. Place the extra shear bolts supplied

(found in parts bag) under each end of the scraper bar next to the

adjustable skids.

4. Loosen the mounting nuts that hold

the adjustable skids. To bring the front of the snow thrower down,

TO ADJUST SCRAPER BAR

After considerable use, the metal scrap- er bar will have a definite wear pattern.

The scraper bar in conjunction with the skids should always be adjusted to al-

low 1/8" between the scraper bar and

the sidewalk or area to be cleaned.

1, Position the snow thrower on a level

surface.

Make sure both tires are equally in-

flated. Proper tire pressure is 14 to

17 PSi. See side of tire for maxi- mum inflation. Do not exceed maxi- mum sidewall pressure on tire.

Loosen the carriage bolts and nuts securing the scraper bar to the au-

ger housing.

Adjust the scraper bar to the proper

position.

Tighten the carriage bolts and nuts,

making sure that the scraper bar is parallel with the working surface.

For extended operation, the scraper bar may be reversed, if the scraper

bar must be replaced due to wear, remove the carriage bolts and nuts

and install a new scraper bar.

F-0310107L 19

BELT ADJUSTMENT

Traction Drive Belt The traction drive belt has constant

spring pressure and does not require an adjustment. If the traction drive belt

is slipping, replace the belt. See "How To Replace The Belts" in the Service

And Adjustment section.

Auger Drive Belt

Ifyour snow blower will not discharge

snow, check the control cable adjust- ment. If it is correct, then check the

condition of the auger drive belt. If it is damaged or loose, replace it (see "How To Replace The Belts" in this section of

the manual).

1. Disconnect spark plug wire.

2, Remove screw from belt cover.

Remove belt cover (see Figure 17),

5. Have someone engage auger drive clutch. Check tension on belt (op-

posite idler pulley). Belt should de-

flect about 1/2 inch (12.5 mm) with

moderate pressure (Figure 18). You may have to move idler pulley more

than once to obtain the correct ten-

sion.

Auger

( _ __ EDnliVlee

--,/_ r, Pulley j _,_O 1/2 inch

.-- "._ (12.5mm)

Idler_._.-C/'_ ._'_\/ Deflection

Pulley }to, 1- ;\

Engaged _ ',

L "

Figure 18

6. Reinstall belt cover.

3. Loosen nut on auger idler pulley and move auger idler pulley towards belt about 1/8 inch (3 mm) (see

Figure 20).

4. Tighten nut.

F-0310107L

7. Whenever belts are adjusted or re- placed, the cables will need to be adjusted. (See Cable Adjustment in

this section of the manual).

8. Attach the spark plug wire.

HOW TO REPLACE THE BELTS

The drive belts are of special construc- tion and must be replaced with original

equipment replacement belts available from your nearest Sears service centen

Some steps require the assistance of a second person.

How To Remove the Auger Drive Belt If the auger drive belt is damaged, the

snow thrower will not discharge snow.

Replace the damaged belt as follows.

1. Disconnect the spark plug wire.

2. Loosen the bolts on each side of

the bottom panel (see Figure 19).

3, Remove the bottom panel.

Bolt Bottom

Panel

Auger

Housing

4. Remove screw from belt cover, Remove the belt cover (see

Figure 17).

5. Loosen the belt guide. Pull the belt guide away from the auger drive

pulley (see Figure 20).

6. Pull the idler pulley away from the auger drive belt.

7. Remove the old auger drive belt

from the auger drive pulley and

_ Traction Drive Be,t

Engine Pulley

from the engine pulley, Replace the auger drive belt with an original

equipment replacement belt avail- able from a Sears service center.

8. Install the new auger drive belt onto the auger drive pulley and

onto pulley.

9. Adjust the auger drive belt. See

"How To Adjust The Auger Drive Belt" in the Service And Adjustment

section.

10. Adjust the belt guide. See "How To Adjust The Belt Guide" in the Ser-

vice And Adjustment section.

11. Install the belt cover. Tighten

screw (See Figure 17).

12. Check the adjustment of the cables.

See "How To Check And Adjust The Cables" in the Service And Adjust-

ment section.

13. Install the bottom panel (see

Figure 19).

14. Tighten the bolts on each side of the bottom panel.

15. Connect the spark plug wire.

Belt Guide

Auger Idler Pulley

E-Ring

Swing Plate

Axle Rod

F-03t0107L 21

Auger Drive Pulley

Auger Drive Belt

Traction Drive

Spring

Traction Drive Belt

Traction

Drive Pulley

Engine Pulley

Figure 20

How To Remove

The Traction Drive Belt

Ifthe snow thrower will not move for-

ward, check the traction drive belt for

wear or damage. If the traction drive belt is worn or damaged, replace the

belt as follows,

1, Disconnect the spark plug wire,

2, Remove the auger drive belt. See

"How To Remove The Auger Drive Belt" in the Service And Adjustment

section,

plate is properly secured (see Figure 21),

3, Remove the e-ring from one end of

the swing plate axle rod. Remove the swing plate axle rod to allow

the swing plate to pivot forward (see

Figure 20).

4. Remove the traction drive spring.

5, Remove the old traction drive belt

from the traction drive pulley and from the engine pulley, Replace

the traction drive belt with an origi-

nal equipment replacement belt available from a Sears service cen-

ter,

6, Install the new traction drive belt

onto the traction drive pulley and onto engine pulley,

7. Make sure the traction drive idler

pulley is properly aligned with the

traction drive belt.

8. Attach the traction drive spring.

9, Install the swing plate axle rod and

secure with the e-ring removed earlier.

10, The bottom of the swing plate must

be positioned between the align- ment tabs. Make sure the swing

F-0310107L

Alignment Tabs Figure 21

NOTE: If the drive will not engage after the traction drive belt has

been replaced, then check to

make sure that the swing plate is positioned between the align* ment tabs.

11,

Install and adjust the auger drive belt. See "How To Remove The Au-

ger Drive Belt" in the Service And Adjustment section,

12, Adjust the belt guide, See "How To

Adjust The Belt Guide" in the Ser-

vice And Adjustment section,

13, Install the bottom panel (see

Figure 19),

14, Tighten the bolts on each side of

the bottom panel,

15, Install the belt cover. Tighten

screw (see Figure 17),

16, Check the adjustment of the cables,

See "How To Check And Adjust The Cables" in the Service And Adjust-

ment section.

17, Connect the spark plug wire.

BELT GUIDE ADJUSTMENT

1, Remove spark plug wire, 2, Have someone engage auger drive, 3, Measure the distance between the

belt guide and belt, The distance should be 1/8 inch (3.175 mm) for

guide, See Figure 22.

"Z" Fitting

__. Belt Guide _'t" d 1/8 inch

Auger idler f_", _ _'_" (3.175 ram)

EPnu_eYed%__

Figure 22

4. If adjustment is necessary, loosen

belt guide mounting bolt. Move belt

guide to the correct position. Tight-

en mounting bolt.

5. Reinstall belt cover.

6. Reconnect spark plug wire.

HOW TO CHECK AND ADJUST THE CABLES

The cables are adjusted at the factory and no adjustment should be neces- sary. If the cables have become

stretched or are sagging adjustment will be necessary. Whenever belts are adjusted or re-

placed, the cables will need to be ad- justed.

To check for correct adjustment, un- hook "Z" fitting at clutch lever (see

Figure 23),

1. Move clutch ]ever to the full forward position (just contacting plastic

bumper). Holding cable tight, note position of fitting to hole in clutch le-

ver.

F-O310107L

2, The center of the "Z" fitting should

be between the center and top of

the hole in the clutch lever. Adjust

either the auger drive cable or the

traction drive cable as as necessary

according to the following instruc-

tions,

Auger Drive Cable Adjustment

1. Run the engine until the fuel tank is empty and the engine stops.

2. Stand the snow thrower up on the front end of the auger housing.

3. Push cable through spring to ex- pose the threaded portion of the cable (see Figure 24).

Square End

Cable Spdng

Locknut

4, Hold square end of threaded portion

with pliers and adjust Iocknut in or out until correct adjustment is

reached. Pull cable back through spring and connect cable.

Figure 23

Figure 24

_'_l,]= WlI I.,y:l .,]qiU_,._lIiviIQI i i

TRACTION DRIVE CABLE ADJUSTMENT

1, Runthe engine until the fuel tank is 7, Pushthe bottomof thetraction

empty and the engine stops.

2. Stand the snow thrower up on the front end of the auger housing.

3. Loosen the bolts on each side of the bottom panel (see Figure 25).

Bolt Bottom Panel

Auger

Housing

Figure25

4. Remove the bottom panel.

5. Disconnect the "Z" fitting from the

drive lever (see Figure 23).

6. Slide the cable boot off the cable

adjustment bracket (see Figure 26).

drive cable through the cable ad-

justment bracket until the "Z"

hook can be removed.

8. Remove the "Z" hook from the cable adjustment bracket. Move

the "Z" hook down to the next ad- justment hole.

9. Pull the traction drive cable up

through the cable adjustment

bracket.

10. Put the cable boot over the cable

adjustment bracket.

11. Install the "Z" hook to the traction drive lever (see Figure 23).

12. To check the adjustment, depress

the drive lever and check the length of one of the drive springs. In cor-

rect adjustment, the length of the drive spring is: minimum 3" (76 mm.)

maximum 3-3/8" (85 mm.) (see Figure 27).

3" min.,

3-3/8" max.

/ /

TractiooS

,)_able riveB°ot_-_jCable/,}

,#:-Y 4_¢ _-

Cable_Adjustment /_ "Z" Hook Bracket Figure26

F-0310107L 24

Drive Spring Figure 27

HOW TO ADJUST OR REPLACE

THE FRICTION WHEEL

How To Check The Friction Wheel Ifthe snow thrower will not move for-

ward, check the traction drive belt, the

traction drive cable or the friction wheel.

Ifthe friction wheel is worn or damaged, it must be replaced. See "How To Re- place the Friction Wheel" in this section.

Ifthe friction wheel is not worn or dam- aged, check as follows.

1. Run the engine until the fuel tank is empty and the engine stops.

2. Stand the snow thrower up on the front end of the auger housing

(see Figure 28).

3. Disconnect the spark plug wire.

4. Loosen the bolts on each side of the bottom panel (see Figure 28).

5. Remove the bottom panel.

6. Position the shift speed lever in the lowest forward speed.

7. Note the position of the friction wheel (see Figure 29). The correct

distance "A" from the right side of

the friction wheel to the outside of the motorbox is as follows:

Tire Size Distance "A"

12 and 13 inch 4-1/8" 16 inch 4-5/16"

If the friction wheel is not in the correct position, adjust according to

the following instructions.

5. Install the bottom panel (see Figure 28).

6. Tighten the bolts on each side of the bottom panel.

Bolt Bottom Panel

Auger Housing

Bolt

Figure28

Figure29

Speed Control Rod

Lo'--_sen Bolts

How To Adjust The Friction Wheel

1. Position the shift speed lever in the lowest forward speed.

2. Loosen the bolts on the speed control rod (see Figure 30).

3. Move the friction wheel to the cor- rect position (see Figure 29).

4. Tighten the bolts on the speed control rod (see Figure 30).

F-03t0107L

Figure 30

How To Replace The Friction Wheel

Ifthe friction wheel is worn or damaged,

the snow thrower will not move forward. The friction wheel must be replaced as

follows.

1. Run the engine until the fuel tank is empty and the engine stops.

2. Stand the snow thrower up on the front end of the auger housing (4).

(see Figure 28).

3. Disconnect the spark plug wire.

4. Remove the fasteners that secure the right wheel. Remove the right

wheel from the axle (see Figure 31)

5. Loosen the bolts on each side of the bottom panel.

6. Remove the bottom panel.

7. Remove the fasteners that secure the drive sprocket to the axle (see

Figure 32).

8. Remove the left wheel, axle, and

drive sprocket.

9. Remove the four bolts that hold the

bearings on each side of the hex shaft (see Figure 33).

Bottom Panel

Chain

Wheel

Figure 31

Figure 32

Bolts

10. Remove the hex shaft and bear- ings.

NOTE: Take special note of the posi- tion of the washers on the hex shaft.

F-03t0107L 26

Figure 33

11. Remove the three fasteners that hold the friction wheel to the hub (see Figure 34).

12. Remove the friction wheel from the

hub. Slip the friction wheel off the hex shaft.

13. Assemble the new friction wheel

onto hub with the fasteners re-

moved earlier.

14. Install the hex shaft and bearings

with the four bolts removed earlier

(see Figure 35).

Make sure the washers are prop* erly installed in the original posi-

tion. Also, make sure the two washers are properly aligned

with the actuator arms.

15. Make sure the hex shaft turns free- ]y.

16. Install the left wheel, axle, and drive sprocket with the fasteners removed earlier. Install the chain

onto the drive sprocket (see

Figure 32).

17. Check the adjustment of the friction wheel. See "How To Adjust The

Friction Wheel" in this section.

18. Make sure the friction wheel and the

disc drive plate are free from grease

or oil.

19. Install the bottom panel (see

Figure 31).

20. Tighten the bolts on each side of the bottom panel.

21. Install the right wheel to the axle with the fasteners removed earlier.

22, Connect the spark plug wire.

Fasteners Hub Wheel

Hex Sha_

Friction

Fasteners

Figure 34

Actuator Arms

Bearings

Washer

F-0310107L 27

Bearings

Washer

Figure 35

HOW TO REPLACE

THE AUGER SHEAR BOLT

The augers are secured to the auger shaft with special shear bolts. These

shear bolts are designed to break and protect the machine if an object be-

comes lodged in the auger housing. Do not use a harder bolt as the protection

provided by the shear bolt will be lost.

2. Disconnect the spark plug wire.

Make sure all moving parts have stopped.

3. Align the hole in the auger with the hole in the auger shaft. Install the new shear pin and spacer, See

Figure 36.

4. Connect the spark plug wire.

,_ WARNING: For safety and to

shear bolts.

To replace a broken shear bolt, proceed as follows. Extra shear bolts were pro-

vided in the assembly parts bag.

1. Move the throttle control to the stop

protect the machine, use only original equipment

position. Disengage all controls.

TO ADJUST THE CARBURETOR

Ifyou think your carburetor needs ad- justing, contact your nearest Sears Ser- vice Center. Engine performance

should not be affected at altitudes up to 7,000 feet. For operation at higher

elevations, contact your nearest Sears Service Center

IMPORTANT: Never tamper with the engine governor, which is factory set for

proper engine speed. Over-speeding

-- 4rP'°er

• /F, ore30

the engine above the factory high speed setting can be dangerous. If you think the engine-governed high speed

needs adjusting, contact your nearest

Sears Service Center, which has the

proper equipment and experience to make any necessary adjustments. For

the location of the nearest Sears Ser- vice Center, call Sears Service at

1-800-4-MY-HOME®.

F-O310107L 28

,_lb WARNING: Never store your

snow thrower indoors or in an enclosed, poorly venti-

lated area. If gasoline remains in the tank, fumes may reach an open

flame, spark or pilot light from a fur- nace, water heater, clothes dryer,

cigarette, etc.

To prevent damage (if snow thrower is not used for more than 30 days) follow the steps below.

SNOW THROWER

1, Thoroughlycleanthesnowthrower,

2, Lubricate all lubrication points,See

the Maintenancesection,

3. Be sure that all nuts, bolts and

screws are securely fastened, in- spect all visible moving parts for

damage, breakage and wear. Re- place if necessary.

4. Touch up all rusted or chipped paint

surfaces; sand lightly before paint- ing.

5. Cover the bare metal parts of the

blower housing auger and the im- peller with rust preventative, such

as a spray lubricant.

NOTE: A yearly checkup or tune-up by a Sears service center is a good way of

ensuring that your snow thrower will provide maximum performance for the

next season.

ENGINE

Gasoline must be removed or treated to prevent gum deposits from forming in

the fuel tank, filter, hose, and carburetor during storage. Also, during storage al-

cohol blended gasoline that uses etha- nol or methanol (sometimes called

gasohol) attracts water, it acts on the gasoline to form acids which damage

the engine.

Run the engine until the fuel tank is empty and the engine stops.

If you do not remove the gasoline, use fuel stabilizer supplied with unit

or purchase Craftsman Fuel Stabi-

lizer No. 3550. Add fuel stabilizer to any gasoline left in the tank to mini-

mize gum deposits and acids. If the

fuel tank is almost empty, mix stabi-

lizer with fresh gasoline in a sepa- rate container and add some to the

fuel tank.

Always follow the instructions on the

stabilizer container. After the stabi- lizer is added to the fuel tank. run

the engine at least ten minutes to

allow the mixture to reach the car- buretor.

Change the engine oil.

Lubricate the piston/cylinder area. First, remove the spark plug and

squirt a few drops of clean engine

oil into the spark plug hole. Next,

cover the spark plug hole with a rag

to absorb oil spray. Then, pull two or three times on the recoil starter rope

to rotate the engine. Finally, install the spark plug and attach the spark

plug wire.

OTHER

1, if possible, store your snow thrower

indoors and cover it to give protec-

tion from dust and dirt.

2. If the snow thrower must be stored outdoors, put the snow thrower on

blocks to raise it off of the ground.

3. Cover the snow thrower with a suit- able protective cover that does not retain moisture. Do not use plastic.

IMPORTANT: Never cover snow

thrower while engine and exhaust areas are still warm.

F-O310107L 29

+ 67 hidden pages

Craftsman 536887994 Owner’s Manual

Specifications and Main Features

Frequently Asked Questions

User Manual