Craftsman 536885170 Owner’s Manual

InstructionBook

SnowThrower

Model 621500x89A

Manueld'instructions

Readand keep this book for future reference. This book contains important information on SAFETY,

ASSEMBLY,OPERATION,AND MAINTENANCE.

Lisez et conservez ce manuel pour r_f_rence.Ce manuel contient des informationsimportantes concernant laSECURITE,LE MONTAGE,L'UTILISATIONET L'ENTRETIEN.

chasse-neige

module 621500x89A

F-OO1168M

NOTE: This unit is equipped with an internal combustion engine and must not be used on or near any unimproved forest-covered, brush-covered or grass-covered land unless

the engine's exhaust system is equipped with a spark arrester meeting applicable local or state laws (if any). If a spark arrester

is used, it must be maintained in effective working order by the operator,

In the State of California, the above is required by law (Section

4442 of the California Public Resources Code), Other states may have similar laws, Federal laws apply on federal lands. See

an Authorized Service Center for a spark arrester for the muffler.

Engine Exhaust, some of its constituents, and

certain vehicle components contain or emit chemicals known to the State of California to

cause cancer and birth defects or other repro- ductive harm.

Battery posts, terminals and related accesso- ries contain lead and lead compounds, chemi-

cals known to the State of California to cause cancer and birth defects or other reproductive

harm. WASH HANDS AFTER HANDLING.

REMARQUE : cette machine est 6quip6e d'un moteur

combustion interne et ne dolt pas _tre utilis6e sur un terrain forestier, buissennant eu herbeux non pr6par6, a moins que le

dispositif d'6chappement seit pourvu d'un pare-6tincelles cenforme a la 16gislatien locale eu de 1'6tat (le cas 6ch6ant), Si

un pare-etincelles est utilis6, celui-ci dolt _tre maintenu en parfait 6tat de fonctionnement par I'utilisateur.

Au sein de 1'6tat de Californie, la Ioi exige la prise en compte des pr6cautions mentienn6es ci-dessus (clause 4442 du

California Public Resources Code). D'autres 6tats peuvent pr6senter des lois similaires. Les lois f6d@ales s'appliquent sur les terres f6d6rales, S'adresser & un centre de maintenance

agr66 pour I'achat d'un pare-6tincelles pour 1'6chappement.

Les gaz d'_chappement du moteur, certains

_ldments de leur composition, ainsi que certains organes du v_hicule contiennent ou

_mettent des substances chimiques qui, selon

I'Etat de Californie, peuvent causer ie cancer,

des malformations & la naissance, ou reprdsentent un danger pour la reproduction.

Les bornes et p61es de batterie et autres

accessoires de ce type contiennent du piomb et des composds de p/omb, substances chimiques qui, selon I'Etat de Californie,

peuvent causer le cancer, des malformations

la naissance, ou representent un danger pour la

reproduction.

Fq)O1168M 2

1 _2

Fq)O1168M 3

l._._z

F_OO1168M

1._33 14

Fq)O1168M 5

CONTENTS

PRODUCT INFORMATION 6 OWNER'S INFORMATION 6 INTERNATIONAL PICTORIALS 7

ASSEMBLY 9 OPERATION 10

MAINTENANCE 12 MAINTENANCE CHART 12

TROUBLE SHOOTING CHART 14

TWO YEAR LIMITED WARRANTY

Murray, Inc. warrants to the original purchaser that this unit shall be free from defects in

material and workmanship under normal use and service for a pedod of Two (2) Years from the date of purchase; however, this warranty

does not cover engines, accessories (such as electdc starters) and Normal Wear Parts (except

as noted below) as the companies that manufacture these items furnish their own

warranties and provide service through their authorized field service facilities. For additional

information, see the warranties covering these particular parts. If you are uncertain whether

your unit contains or is equipped with one or more of these pads, consult your dealer prior to

purchase. Subject to the terms and conditions noted in this Limited WarTanty, we shall, at our

option, repair or replace at no cost to the original purchaser any part covered by this Limited

Warranty during the applicable warranty period.

Normal Wear Parts are defined as drive belts, augers, shear pins, tires and headlights. These parts are warranted to be free from defects in material and workmanship as delivered with the

product. Any claim for repair or replacement of

Normal Wear Parts must be made within thirty (30) days of the date of purchase. No claims

involving damage caused from material use, abuse or misuse will be honored.

This Murray, inc. Two (2) Year Limited Warranty is your exclusive remedy; however,

this warranty is void or does not apply to any unit that has been tampered with, altered,

misused, abused or used for rental or other commercial and/or professional

(non-homeowner) uses. Your warranty does not cover minor mechanical adjustments which are

not due to any defect in material or workmanship. For assistance in making such adjustments, consult your instruction Book.

To make a claim under this Murray, inc. Two (2)

ENGLISH

Year Limited Warranty, return the unit (or if authorized in advance, the defective part) along

with your proof of purchase to an Authorized Service Center near you. To locate the nearest

Authorized Service Center, call the Central Parts

Distributor for your area shown in the list provided with your unit or check the Yellow Page

listings in your local telephone directory. If you

return the entire unit, we will repair the unit. ffwe authorize the return of the defective part only, we will either replace or repair the part.This Murray,

Inc. Two (2) Year Limited Warranty gives you specific legal rights, and you may also have

other rights which vary from state to state. This

Limited Warranty is given in lieu of all other expressed and implied warranties including

the implied warranty of merchantability and warranty of fitness for a particular purpose. If

you need additional information on this written warranty or assistance in obtaining service, write:

MURRAY, INC.

Outdoor Power Equipment Customer Service Department

no. Box 268

Brentwood, Tennessee 37027

1-800-251-8007

PRODUCT INFORMATION

The owner must be certain that all the product information is included with the unit. This

information includes the INSTRUCTION BOOKS, the REPLACEMENT PARTS and the

WARRANTIES. This information must be included to make sure state laws and other laws are followed.

OWNER'S INFORMATION

This instruction book is written for a person with some mechanical ability. Like most service

books, not all the steps are described. Steps on how to loosen or tighten fasteners are steps anyone can follow with some mechanical ability.

Read and follow these instructions before you use the unit.

Know your product: If you understand the unit and how the unit operates, you will get the best

performance. As you read this manual, compare the iIIustrations to the unit. Learn the location

and the function of the controls. To help prevent an accident, follow the operating instructions

and the safety rules. Keep this manual for future reference.

IMPORTANT: Many units are not assembled

and are sold in cartons. It is the responsibility of the owner to make sure the assembly instruc- tions in this manual are exactly followed. Other

units are purchased in an assembled condition. On assembled units, it is the responsibility of the

owner to make sure the unit is correctly as- sembled. The owner must carefully check the

unit according to the instructions in this manual before it is first used.

WARNING: Look for this symbol to indicate important safety precautions. This symbol

indicates: "Attention! Become Alert! Your

Safety Is At Risk."

Responsibility Of The Owner

The responsibility of the owner is to

follow the instructions below.

1. Carefully read and foIIowtherules for safe operation.

2. Follow all the assembly and preparation instructions.

3. Inspect the unit.

4. Make sure that the operator of the unit knows how to correctly use all standard

and accessory equipment.

5. Operate the unit only with guards, shields, and other safety items in place and working

correctly.

6. Correctly adjust the unit.

7. Service the unit only with authorized or ap- proved replacement pads.

8. Complete all maintenance on the unit.

Environmental Awareness

• Do not fill the engine's fuel tank completeIy full.

• Drain fuel for off-season storage.

• Use only unleaded gasoline.

• Service the air cleaner regularly.

• Tune-up the engine regularly.

• Keep equipment in efficient operating condition.

• Dispose of used engine oil properly.

Fq)O1168M 6

INTERNATIONAL PICTORIALS

IMPORTANT: The following pictorials are lo- cated on your unit or on literature supplied

with the product. Before you operate the unit, learn and understand the purpose for

each pictorial.

ENGLISH

Safety Warning Symbols

DANGER DANGER

Thrown Objects. Thrown Objects.

Keep Bystanders Away, Keep Bystanders Away. WARNING

DANGER

Stop The Engine

WARNING Before Unclogging

Hot Surface STOP Discharge Chutet

Control And 0perat_ols ) _

Slow Fast Electric Start Engine Start Engine Run Engine Off

IMPORTANT

Read Owner's Manual

Before Operating

This Machine.

DANGER

Avoid Injury From

Rotating Augen Keep

Hands, Feet And

Clothing Awa_

0 I I,I H N

Engine Stop On Choke Off Choke On Neutral Forward

Reverse Throttle Primer Button Ignition Key Ignition Off Ignition On

Electric Starter Engage Auger Clutch Auger Collector Discharge DOWN Discharge UP

Discharge LEFT Discharge RIGHT Drive Clutch Fuel

Oil Fuel Oil Mixture

Weight Transfer

Lift Handle To Engage

Weight Transfer

Depress Pedal To Disengage

Transmission

Insert To Run, Pull Out To Stop.

Ignition Key

Fq)O1168M 7

Safe Operation Practices for Snow Throwers

As Recommended By: American National Standards Institute.

ENGLISH

IMPORTANT: Safety standards require operator presence controls to minimize the risk of injury. Your snow thrower is equipped with such con-

trols. Do not attempt to defeat the function of the operator presence control under any circum-

stances.

Training

1. Read the operating and service instruction manual carefully. Be thoroughly familiar with

the controls and the proper use of the equip-

ment. Know how to stop the unit and disen-

gage the controls quickly.

2. Never allow children to operate the equip- ment. Never alow adults to operate the

equipment without proper instruction.

3. Keep the area of operation clear of alI per- sons, particularly smali chiIdren and pets.

4. Exercise caution to avoid slipping or falling especially when operating in reverse.

Preparation

1. Thoroughly inspect the area where the equip- ment is to be used and remove all doormats,

sleds, boards, wires, and other foreign ob-

jects.

2. Disengage all clutches before starting the en- gine (motor).

3. Do not operate the equipment without wear-

ing adequate winter outer garments. Wear

footwear that will improve footing on slippery

surfaces.

4. Handle fuel with care; it is highly flammable.

a. Use an approved fuel container. b. Never remove fueI tank cap or add fuel to

a running engine (motor) or hot engine (motor).

c. Fill fuel tank outdoors with extreme care.

Never fill fuel tank indoors.

d. Reptace fuel cap securely and wipe up

spilled fuel.

e. Never store fuel or snow thrower with fuel

in the tank inside of a building where fumes may reach an open flame or spark.

Check fuel supply before each use, allow- ing space for expansion as the heat of the

engine (motor) and/or sun can cause fuel

to expand.

5. For all units with electric starting motors use

electric starting extension cords certified CSA/UL Use only with a receptacle that has

been installed in accordance with local in- spection authorities.

6. Adjust the snow thrower height to dear gravel or crushed rock surface.

Never attempt to make any adjustments

while the engine (motor) is running (except when specifically recommended by manufac- turer).

Let engine (motor) and snow thrower adjust

to outdoor temperatures before starting to

dear snow.

Always wear safety glasses or eye shields

dudng operation or while performing an ad-

justment or repair to protect eyes from foreign

objects that may be thrown from the snow

thrower'.

Operation

Do not operate this machine if you are taking drugs or other medication which can cause

drowsiness or affect your ability to operate

this machine.

2. Do not use this machine if you are mentally or physically unable to operate this machine

safely.

3. Do not put hands or feet near or under rotat- ing parts. Keep clear of the discharge open-

ing at all times.

4. Exercise extreme caution when operating on or crossing gravel drives, walks or roads.

Stay alert for hidden hazards or traffic.

After striking a foreign object, stop the engine

(motor), remove the wire from the spark plug,

thoroughly inspect snow thrower for any

damage, and repair the damage before re- starting and operating the snow thrower.

If the unit should start to vibrate abnormally, stop the engine (motor) and check immedi-

ately for the cause. Vibration is generally a

warning of trouble.

Stop the engine (motor) whenever you leave

the operating position, before unclogging the

auger/impeller housing or discharge chute and when making any repairs, adjustments,

or inspections.

When cleaning, repairing, or inspecting, make

certain the augedimpeIler and all moving parts have stopped and all controls are dis-

engaged. Disconnect the spark plug wire and keep the wire away from the spark plug to

prevent accidental starting.

Take all possible precautions when leaving the snow thrower unattended. Disengage the

auger/impeller, stop engine (motor), and re- move key.

10.

Do not run the engine (motor) indoors, except

when starting the engine (motor) and for transporting the snow thrower in or out of the

building. Open the outside doors; exhaust

fumes are dangerous (containing CARBON

MONOXIDE, an ODORLESS and DEADLY GAS).

11. Do not clear snow across the face of slopes. Exercise extreme caution when changing

direction on slopes. Do not attempt to dear steep slopes.

12. Never operate the snow thrower without proper guards, plates or other safety protec-

tive devices in place.

13. Never operate the snow thrower near enclos- ures, automobiles, window wells, drop-offs,

and the like without proper adjustment of the snow discharge angle. Keep children and

pets away.

14. Do not overload the machine capacity by at- tempting to clear snow at too fast a rate.

15. Never operate the machine at high transport speeds on slippery surfaces. Look behind

and use care when backing up.

16. Never direct discharge at bystanders or aliow anyone in front of the unit.

17. Disengage power to the collector/impeller when snow thrower is transported or not in

use.

18.

Use only attachments and accessories ap- proved by the manufacturer of the snow

thrower (such as tire chains, electric start kits, ect.).

19.

Never operate the snow thrower without good visibility or light. Always be sure of your foot-

ing and keep a firm hold on the handles. Walk;never run.

20.

Do not over-reach. Keep proper footing and balance at all times.

21.

Exercise caution if operating on steep siop- ing surfaces.

22.

This snow thrower is for use on sidewalks, driveways and other ground level surfaces.

23.

Do not use the snow thrower on surfaces above ground level such as roofs of resi- dences, garages, porches or other such

structures or buiidings.

Maintenance And Storage

1. Check shear"bolts and other bolts at frequent intervals for proper tightness to be sure the

equipment is in safe working condition.

2. Never store the snow thrower with fuel in the tank inside a building where ignition sources

are present such as hot water and space heaters, clothes dryers, and the like. Allow the engine (motor) to cool before storing in

any enclosure.

3. Always refer to operator's guide instructions for important details if the snow thrower is to

be stored for an extended period.

4. Maintain or replace safety and instruction Ia- bels, as necessary.

5. Run the snow thrower a few minutes after throwing snow to prevent freeze-_p of the auger/impelIer.

Fq)O1168M 8

ASSEMBLY

Read and follow the assembly and adjustment instructions for your snow thrower. All fasteners are in the parts bag. Do not discard any parts or

material until the unit is assembled.

assembly or maintenance to the

m_lL WARNING: Before doing any

snow thrower, remove the wire

from the spark plug.

NOTE: In this instruction book, left and right describe the location of a part from the oper- ator's position behind the unit.

NOTE: Torque is measured in foot pounds (metric N.m). This measurement describes how tight a nut or bolt must be. The torque is

measured with a torque wrench. NOTE: Illustrations begin on page 3.

Tools Required

1 Knife 1 Pliers

1 1/2 inch adjustable open end wrenches 1 9/16 inch adjustable open end wrenches 1 3/4 inch adjustable open end wrenches

1 Measuring tape or ruler 1 Screwdriver

How To Remove The Snow Thrower From The Carton

1. Locate all parts that are packed separately and remove from the carton.

2. Remove and discard the packing material from around the snow thrower.

3. Cut down all four corners of the carton and lay the side panels fiat.

4. Hold onto the lower handle and pull the snow thrower off the carton.

CAUTION: DO NOT back over cables.

5. Remove the packing material from the han- dle assembly.

How To Assemble The Handle

1. Remove the packing material from the upper and lower handles.

2. (Figure 1) Loosen the knobs (1) on each side of the handle (2).

3. Raise the upper handle (2) to the operating

position.. Hold the upper handle (2) apart to prevent scratching the lower handle.

NOTE: Make sure the cables are not

caught between the upper and lower han- dle.

4. Tightenthe knobs (1).

How To Prepare The Engine

A WARNING: Follow the engine

'_ type of fuel and oil to use. Always

See the engine manufacturer's instructions for the type of fuel and oil to use. Before you use

the unit, read the information on safety, opera- tion, maintenance, and storage.

manufacturer's instructions for the

use a safety fuel container. Do not smoke when adding the fuel mixture to the engine.

When inside an enclosure, do not fill the fuel tank. Before you add the fuel mixture,

stop the engine. Let the engine cool for several minutes.

How To Mix The Fuel Mixture

The two cycle engine, used on this snow throw- er, requires a mixture of gasoline and oil for lu-

brication of the beadngs and other moving parts. The correct fuel mixture ratio is 50:1 (2.6 oz. oil

per one gallon of gas - see the Fuel Mixture Chart). Gasoline and oil must be pre-mixed in a clean gasoline container. Always use fresh,

clean, unleaded gasoline.

ENGLISH

FUEL MIXTURE CHART (mixture 50:1)

I 0s I '"pE"''LI s'(""o I

Mix gasoline and oil as folIows:

1. Pour one (1) U.S. quart of fresh, clean, un- leaded automotive gasoline into a one gallon

size gasoline container.

2. Add 2.6 ounces of clean, high quality, two- cycle oil to the gasoline container.

IMPORTANT: Do not use outboard motor oil or multi-viscosity oils,such as 10W-30

or 10W_,0.

3. Install the fuel cap onto the gasoline contain-

er. Vigorously shake the gasoline container

to mix the oil with the gasoline.

4. Add an additional three (3) U.S. quarts of gasoline to the gallon container. Again shake

the gasoline container.

Before You Operate Before you operate your new snow thrower,

please review the following checklist:

• Make sure all assembly instructions have been completed.

• Make sure the discharge chute rotates freely.

• Make sure that no loose parts remain in the

carton.

As you ieam how to propedy use the snow thrower, pay extra attention to the foilowing im-

portant items.

• Make sure the fuel tank is filled with the

correct mixture o1gasoline and oil.

• Become familiar with the location of all

controls and understand their function.

• Before starting the engine, make sure aii

controls operate correctly.

Do not fill the fuel tank with gasoline that does not have oil mixed in it. Shake the gasoline container before each filling of the fuel tank.

Oll Add more gas (2.6ozl Shake Can (3U. S. Quarts)

1 U.S. Galton container '_-

Fq)01168M 9

OPERATION

NOTE: Illustrations begin on page 3.

Know Your Snow Thrower (Figure 2)

Read this Instruction Book and safety rules be- fore operation the snow thrower'. Compare the illustration with your snow thrower to familiarize

yourself with the location of various controls and adjustments.

Crank Assembly (2) - Changes the direction of the discharge chute.

Discharge Chute (3) - Changes the distance the snow is thrown.

Auger Drive Lever (5) - Starts and stops the au- ger which propels the snow thrower.

Ignition Key (8) - Must be inserted and turned to the on position to start the engine.

Primer Button (9) - Injects fuel directly into the carburetor for fast starts in cold weather.

Electric Start Button (10)-On electric start mod- ds, used to start the engine.

Switch Box (11) - On electric start models, used to attach a 120 vdt dectric power cord.

Recoil Starter Handle (12) - Use to manually start the engine.

Choke Control (14) - Use to start acdd engine.

Spark Plug Access Panel (15) - Remove to ac- cess the spark plug.

How To Control The Discharge Of The Snow

charge of snow toward bystanders.

WARNING: Never direct the dis-

_IIL ARNING: Always stop the engine

1. (Figure 2) Turn the crank assembly (2) to

2. (Figure 3) Loosen the wing knob (1) on the

3. Move the chute deflector (2) up for more

4. Tighten the wing knob (1).

How To Throw Snow (Figure 2)

1. Engage the auger drive lever (5).

2. To stop throwing snow, release the auger

_ ARNING: The operation of any

before unclogging the discharge chute or the auger housing and be-

fore leaving the snow thrower.

change the discharge direction of the snow.

chute deflector (2).

distance or down for less distance.

drive lever (5).

snow thrower can result in foreign objects being thrown into the eyes,

which can result in severe eye damage. Always wear safety glasses or eye shields

while operating the snow thrower. We rec- ommend standard safety glasses or use a wide vision safety mask over your glasses.

Fq)01168M

How To Stop Discharging Snow

(Figure 2)

1. To stop discharging snow, release the auger drive lever (5).

2. To stop the engine, turn the ignition key (8) to the off position.

How To Move Forward (Figure 4)

1. Hold the auger drive lever (5) against the handle (2). The auger will begin rotating.

2. To go forward, raise the handle (2) to allow the rubber auger blades (f) to contact the

ground. Maintain a firm hold on the handle (2) as the snow thrower starts to move for- ward. Guide the snow thrower by moving the

handle (2) either left or right. Do not attempt

to push the snow thrower.

3. To stop, rdease the auger drive lever (5).

NOTE: If the auger continues to rotate, see

"How To Adjust The Auger Control Cable" in the Service and Adjustments section.

Before Starting The Engine

1. Before you service or start the engine, famii- iarize yourself with the snow thrower'. Be

sure you understand the function and loca- tion of all controls.

2. Make sure that all fasteners are tight.

3. Make sure the fuel tank is filled with the cor- rect mixture of gasoline and oil.

4. Become familiar with the location of all con-

trois and understand their function.

5. Before starting the engine, make sure all

controIs operate corrently.

Add The Fuel Mixture

_k ARNING: Follow the engine

manufacturer's instructions for the

type of fuel and oil to use. Always

use a safety fuel container. Do not smoke when adding the fuel mixture to the engine. When inside an enclosure, do not fill the

fuel tank. Before you add the fuel mixture, stop the engine. Let the engine cool for

several minutes.

(Figure 4) Fill the fuel tank (3) to the full posi- tion with a fresh, clean furl mixture. See "How

To Mix The Fuel Mixture" in the Assembiy sec- tion.

How To Stop The Engine (Figure 2)

To stop the engine, turn the ignition key (8) to the off position. Keep the ignition key (8) in a

safe place. The engine will not start without the ignition key (8).

How To Start The Engine (Figure 2)

Models equipped with an Electric Starter

NOTE: An electric starter kit can be added to

recoil start engines. Electric starter kits are

available from your nearest authorized ser- vice center.

ENGLISH

,_ WARNING: The starter is equipped

How To Start A Cold Engine (Figure 2)

1. Fill the fuel tank with a fresh, clean fuel mis-

2. Move the choke control to FULL position.

3. Make sure the auger drive lever (5) is in the

4. Insert the ignition key (8) and turn to the on

5. Move the choke control (14) to the full

6. (Electric Start) Connect the power cord to

7. (Electric Start) Plug the other end of the

8. Push the primer button (9). Every time you

9. (Electric Start) Push on the electric start

10. (Recoil Start) Rapidly pull the recoil starter

11. If the engine does not start in 5 or 6 tries,

12. (Electric Start) When the engine starts, re-

13. (Electric Start) First disconnect the power

with a three-wire power cord and plug and is designed to operate on

120 volt A.C. household current. The power

cord must be properly grounded at all times

to avoid the possibility of electrical shock which can injure the operator. Carefully fol-

low all instructions in the "How To Start The

Engine" section. Make sure that your house wiring is a three-wire grounded system. If you are not sure, ask a licensed electrician.

If your house wire system is not a three-wire grounded system, do not use

this electric starter under any conditions. If your system is grounded but a three-hole grounded receptacle is not available to start

the engine, have a three-hole grounded re- ceptacle installed by a licensed electrician. To connect a 120 volt A.C. power cord, al-

ways connect the power cord to the switch

box (11) on the engine first. Then, plug the other end into the three-hole grounded re- ceptacle. When disconnecting the power cord, always unplug the end from the

three-hole grounded receptacle first.

ture. See "How To Mix The Fuel Mixture" in the Assembly section.

disengaged (released) position.

position.

choke position.

the switch box (11) located on the engine.

power cord into a three-hole, grounded 120

VOLT, A.C. receptacle. (See the WARNING

in this section).

push the primer button (9), wait two sec-

onds. For the number of times required to

push the primer button (9), see the engine manufacturer's instructions.

button (10) until the engine starts. Do not

crank for more than 10 seconds at a time. The electric starter is thermally protected. If

the electric starter overheates, it will auto-

matically stop and can only be restarted

when it has coded to a safe temperature. A wait of about 5 to 10 minutes is required to

allow the electric starter to cool.

handle (12). Do not allow the recoil starter handle (12) to snap back. Slowly return the recoil starter handle (12).

See the "Trouble Shooting Chart" Instruc-

tions.

lease the electric start button (10) and move the choke control (14) to 1/2 choke position. When the engine runs smoothly,

move the choke control (14) to the off posi-

tion.

cord from the three-hole receptacle. Then, disconnect the power cord from the switch

box (11).

NOTE: In temperatures below O°F, allow

the engine to warm up for several minutes before blowing snow.

_lk ARNING: Never run the engine

How To Start A Warm Engine (Figure 2)

If an engine has been running and is still warm,

leave the choke control (14) in the off position and do not push the primer button (9). If the

engine fails to start, follow the instructions "How To Start A Cold Engine".

NOTE: Do not use the primer button (9) to

start a warm engine.

How To Start An Engine With A Frozen Electric

Starter (Figure 2)

If the electric starter is frozen and will not turn

the engine, follow the instructions below.

1. Pull out the recoil starter handle (12) as far

2. Quickly release the recoil starter handle

If the engine still fails to start, repeat the two pre-

vious steps until the engine starts. Then, contin- ue with the directions "How To Start A Cold

Engine". To help prevent the possible freeze-up of the

recoil starter and of the engine controls, proceed as follows after each snow removal job.

1. With the engine running, quickly pull the re-

indoors or in enclosed, poorly ven- tilated areas. Engine exhaust con-

tains carbon monoxide, an odorless and deadly gas. Keep hands, feet, hair and

loose clothing away from any moving parts located on the engine or the snow thrower.

The temperature of muffler and nearby areas may exceed 150°F. Avoid these

areas.

as possible.

(12). Allow the recoil starter handle (12) to snap back against the recoil starter.

coil starter handle (12) three or four times with a continuous full arm stroke. This will

produce a loud clattering sound that is not harmful to the engine or starter.

2. Stop the engine. Wipe all snow and moisture from the carburetor cover', control levers and cables. Also move the choke control (14) and recoil starter handle (12) several times.

How To Remove Snow or Debris From

The Auger Housing (Figure 2)

_ ARNING: Do not attempt to re-

1. Release the auger drive lever (5).

2. Remove the ignition key (8).

3. Disconnect the spark plug wire.

4. Do not place your hands in the auger hous-

Snow Throwing Tips

1. This snow thrower will propel itself forward

2. Most efficient snowthrowing is accomplished

3. For complete snow removal, slightly overlap

4. Whenever possible, discharge the snow

5. The distance the snow will be discharged

6. In windy conditions, lower tbechute deflector

7. For safety and to prevent damage to the

move snow or debris that may be- come lodged in auger housing

without taking the following precautions.

ing (4) orthe discharge chute (3). Use a pry bar to remove any snow or debris.

when the handle is raised enough to cause the auger blades to contact the ground. The auger should stop when auger control bar is

released. If it does not stop, see "How To Ad-

just The Auger Control Cable" in the adjust-

ment section.

when the snow is removed immediately after

if falls.

each previous path.

down wind.

can be adjusted by moving the discharge chute deflector. Raise the deflector for more

distance or lower the deflector for less dis- tance.

to direct the discharged snow close to the ground where it is less likely to blow into un-

wanted areas.

snow thrower, keep the area to be cleared free of stones, toys and other foreign objects.

ENGLISH

8. Do not use the auger propelling feature when clearing gravel or crushed rock driveways.

Move the handle down to slightly raise the auger.

9. The forward speed of the snow thrower is dependent on the depth and weight of the

snow. Experience will establish the most ef-

fective method of using the snow thrower un- der different conditions.

10.After each snow throwing job, allow the en- gine to run for a few minutes. The snow and

accumulated ice will melt off the engine.

11. Clean the snow thrower after each use.

12. Remove ice, snow and debris from the entire

snow thrower. FIush with water to remove all salt or other chemicals. Wipe snow thrower

dry.

Dry And Average Snow

1. Snow up to eight inches deep can be re-

moved rapidly and easily by walking at a

moderate rate. For snow or drifts of a greater depth,slow your pace to allow the discharge chute to dispose of the snow as rapidly as the auger receives the snow.

2. Plan to have the snow discharged in the di- rection the wind is blowing.

W_ Packed Snow

Move slowly into wet, packed snow. If the wet, packed snow causes the auger to slow down or

the discharge chute begins to clog, back off and

begin a series of short back and forth jabs into

the snow. These short back and forth jabs, four to six inches, will "belch" the snow from the

chute.

Snow Banks And Drifts

In snow of greater depth than the unit, use the same "jabbing" technique described above. Turn the discharge chute away from the snow bank.

More time will be required to remove snow of this type than level snow.

Fq)O1168M 11

+ 25 hidden pages