Craftsman 536882650 Owner’s Manual

10 Horsepower 29 Inch Dual Stage

120V. Electric Start SNOW THROWER

MODEL NO.

536.882650

Caution: Read and follow all Safety

Rules and Operating Instructions before first use

of this product,

SEARS, ROEBUCK AND CO., Hoffman Estates 60179 U.S.A.

760211 10/01f96

Table of Contents 2 Service and Adjustments 18-23 Warranty 2 Storage 24 Safety Rules 2-4 Troubleshooting 25 Contents of Shipping Carton 4-5 Snow Thrower Repair Parts 26-38

Assembly 5-9 Engine Repair Parts 39-42 Operation I0-!4 Spanish(Espa5ol) 43-69 Maintenance t5- t7 Parts Ordering!Service Back Cover

LIMITED TWO-YEAR WARRANTY ON CRAFTSMAN SNOW THROWER

For two years from the date of purchase, when this Craftsman Snow Thrower is main- tained, lubricated, and tuned up according to the operating and maintenance instruc-

tions in the owner's manual, Sears will repair, free of charge, any defect in material or workmanship.

Ifthis Craftsman Snow Thrower is used for commercial or rental purposes, this war- ranty applies for only 90 days from the date of purchase. This warranty does not cover the following:

• items which become worn during normal use, such as spark plugs, drive belts and

shear pins

• Repairs necessary because of operator abuse or negligence, including bent crank

shafts and the failure to maintain the equipment according to the instructions con- tained in the owner's manual.

WARRANTY SERVICE IS AVAILABLE BY RETURNING THE CRAFTSMAN SNOW THROWER TO THE NEAREST SEARS SERVICE CENTER/DEPARTMENT INTHE UNITED STATES. THIS WARRANTY APPLIES ONLY WHILE THIS PRODUCT IS IN USE IN THE UNITED STATES.

This warranty gives you specific legal rights, and you may also have other rights which may vary from state to state.

Sears, Roebuck and Co., D817WA, Hoffman Estates, IL 60179

Look for this symbol to point out important safety precautions. It means--

ATTENTION!!! Become alert!!! Your safety is involved,

Z_ CAUTION: Always disconnect spark plug wire and place wire where it cannot

contact spark plug to prevent accidental starting when setting-up, transporting, adjusting or making repairs.

IMPORTANT: Safety standards require operator presence controls to minimize the risk of injury. Your snow thrower is equipped with such controls Do not attempt to defeat the function of the operator presence control under any circumstances

TRAINING 1 Read the operator's manual carefully.

Be thoroughly familiar with the controls and the proper use of the snow thrower.

Know how to stop the snow thrower and disengage the controls quickly.

2. Never allow children to operate the snow thrower and keep them away

while it is operating Never allow adults to operate the snow thrower without proper instruction Do not carry passen- gers.

3. Keep the area of operation clear of all persons, particularly small children and pets.

4 Exercise caution to avoid slipping or

falling, especially when operating in

reverse.

PREPARATION 1 Thoroughly inspect 1he area where the

snow thrower is to be used and remove all doormats, sleds, boards, wires and

other foreign objects

2 Disengage all clutches before starting

the engine (motor)

3 Do not operate the snow thrower

withoutwearingadequatewinterouter garments..Wearfootwearthatwill improvefootingonslipper,/surfaces.

4, Handlefuelwithcare;itishighly

flammable. (a) Useanapprovedfuelcontainer

(b} Neverremovefueltankcaporadd

fueltoarunningengineorhot engine.

care.Neverfillfueltankindoors.

(d) Replacefueltankcapsecurelyand

wipeupspilledfuel

(e) Neverstorefuelorsnowthrower

withfuelinthetankinsideofa

buildingwherefumesmayreach anopenflameorspark

(f) Checkfuelsupplybeforeeach use,

allowing space for expansion as the heat of the engine (motor) and/ or sun can cause fuel to expand

5. Use extension cords and receptacles as specified by the manufacturer for all

snow throwers with electric drive

motors or electric starting motors

6. Adjust the snow thrower height to clear

gravel or crushed rock surfaces.

7 Never attempt to make any adjustments

while the engine (motor) is running

(except when specifically recom- mended by the manufacturer),

8. Let engine (motor) and snow thrower

adjust to outdoor temperatures before starting to clear snow.

9. Always wear safety glasses or eye shields during operation or while

performing an adjustment or repair to protect eyes from foreign objects that

may be thrown from the snow thrower.

OPERATION

1. Do not operate this machine if you are

taking drugs or other medication which can cause drowsiness or affect your

ability to operate this machine.

2. Do not use this machine if you are

mentally or physically unable 1ooperate this machine safely.

3. Do not put hands or feet near or under rotating parts Keep clear of the

discharge opening at all times.

4 Exercise extreme caution when operat-

ing on or crossing gravel drives, walks, or roads Stay alert for hidden hazards

or traffic.

5. After striking a foreign object, stop the

engine (motor), remove the wire from

the spark plug, disconnect the cord on electric motors, thoroughly inspect the snow thrower for any damage, and repair the damage before restarting and operating the snow thrower

6 Ifthe snow thrower should start to

vibrate abnormally, stop the (motor) and check immediately for the cause Vibration is generally a warning of

trouble..

7. Stop the engine (motor) whenever you leave the operating position, before

unclogging the auger/impeller housing or

discharge guide, and when making any

repairs, adjustments, or inspections

8. When cleaning, repairing, or inspecting, make certain the auger/impeller and all

moving parts have stopped Disconnect the spark plug wire and keep the wire away from the plug to prevent accidental

starting.

9.. Take allpossible precautions when leaving the snow thrower unattended

Disengage the augerlimpeIler, stop

engine, and remove key

10 Do not run the engine indoors, except

when starting the engine and for transporting the snow thrower in or out of the building. Open the outside doors;

exhaust fumes are dangerous (contain- ing CARBON MONOXIDE, an ODOR-

LESS and DEADLY GAS).

tl Do not clear snow across the face of

slopes. Exercise caution when changing direction on slopes. Do not attempt to clear steep slopes

12 Never operate the snow thrower without

proper guards, plates or other safety protective devices in place.

13 Never operate the snow thrower near

glass enclosures, automobiles, window wells, drop-offs, and the like without

proper adjustment of the snow discharge angle Keep children and pets away.

14.. Do not overload the machine capacity by attempting to clear snow at too fast a

rate.

15. Never operate the snow thrower at high transport speeds on slippery sudaces..

Look behind and use care when backing.

16 Never direct discharge at bystanders or

allow anyone in front of the snow thrower

17. Disengage power to the auger!impeller when snow thrower is transportedor not in use.

18 Use only attachmenls and accessories

approved by the manufacturer of the snow thrower (such as tire chains, electric start kits, etc).

19,Neveroperatethesnowthrower

withoutgoodvisibilityorlght.Nways

be sure of your footing, and keep a firm hoId on the bandies. Walk; never

run,

MAINTENANCE AND STORAGE 1,, Check shear bolts and other bolts

frequently for proper tightness to be

sure the snow thrower is in safe working condition

2, Never store the snow thrower with fue!

in the fuel tank inside a building where ignition sources are present such as

hot water and space heaters, clothes

5,,

A ZL_ WARNING: The engine exhaust

from this product contains chemicals known 1othe State of California to cause

cancer, birth defects or other reproductive

harm. /_ WARNING: This snow thrower is for

use on sidewalks, driveways and other ground level surfaces,

Caution should be exercised while using on steep sloping surtaces, DO NOT USE

SNOW THROWER ON SURFACES

ABOVE GROUND LEVEL such as roofs of residences, garages, porches or other such

structures or buildings

Contents el Parts Bag

1. Owner's Manual (not shown) 2- Parts Bags (not shown)

Non Assembly parts

* 2 - Spare Shear Bolts

1t4-20 x 1-3f4 In,,

2-3/8-16 x 2In, Hex Head Bolt

2 -3/8 In,,Flatwashers

2 - 3/8 in., Loekwasher

"2 - Spare t/4 - 20 Locknuts

2- 3/8 ln. Hex Nut

I -11/32 Inch

Flal washer

1 * Starter Motor Cord

I]lui]ll]lu-"l-"lIilllltllllllllltllllllltlillllllllllllllllllllllllllllllllllllfll 1

1- Cable Tie

'2 * Spare Spacers

Parts packed separately in carton (not shown full size)

2- Ignition Keys 1 - container_.k5W30 oil

(Attached toengine in ptastic bag) "__

1 - Mid-Crank Rod 1- Speed Control Rod

CAUTION: Afways wear safety

glasses or eye shields while assembling snow thrower_

TOOLS REQUIRED FOR ASSEMBLY

1 - Knife to cut carton and plastic ties

2 - 1/2 inch wrenches (or adjustable

wrenches)

2 - 9/t6 inch wrenches (or adjustable

wrenches)

t - Pliers (to spread cotter pin) I- Screwdriver

t - Air pressure gauge 1 - Measuring tape or ruler

The figure below shows the snow thrower in

the shipping carton.

The figure befow shows the snow thrower completely assembled

References to the right or left hand side

of the snow thrower are from the view_int of the operator's position behind the unit,

Auger Drive Lever

Remote Chute Deflector Lever

Speed Shifter Lever

Drive

Lever

Crank

Assembly

Cable

Deflector

Height Adjust

Skids

HOW TO SET UP YOUR SNOW THROWER

• Locate and remove container of 5W30 oil and parts bag found in parts box.

• Remove top pallet from carton

• Cut and discard the plastic ties securing the mid-chute rod and speed control rod to the pallet, place them aside Discard pallet

, Cut all four corners of the carton from top

to bottom and lay the panels flat

• Cut the bands holding the snow thrower to the lower pallet,

ASSEMBLE SNOW CHUTE

• Remove back carriage bolt, see figure

below

Carriagem Bolt

INSTALL THE UPPER HANDLE

• Cut ties securing the clutch control cables and remote chute control cable to the

lower handle. Lay cable away from

handles

• Remove the bolts securing the upper handles to the lower handles See figure below NOTE: Discard white plastic washer used for shipping purposes on

the right side,

• Remove upper handle assembly and place it into operating position Upper

handle should be on the outside of the lower handle

NOTE: Unless you have the assistance of another person, it maybe easier to install one

side of the handle at a time NOTE: Make sure the cables are not

caught between the upper and lower

handle

• Replace the bolts, flatwasher, Iockwasher,

and hex nuts removed earlier into the top holes Do not tighten.

//,,Upper handle

• Tilt chute back into operating 3osition See figure below

Chute in operating

position

Carriage-- _

Bolt

• Replace carnage boll

• Tighten carriage bolt securely. NOTE: Check all bolts in chute ring for tightness,

• Remove and discard packaging used to protect chute

Remove

J3/8 Flatwasher

3/8' hex Nu_

}_3/8 X 2" Screw

318"Lockwasher

• Install hardware supplied in parts bag (screws, flatwashers, Iockwashers, and

hex nuts) into the lower holes

• Tighten all four bolts

• Replace protective caps onto screws in upper holes

CONNECTHEADLIGHT

- Connectwireharnessterminalsto headlightassemblylocatedundercontrol

panelasshowninthefigurebelow

• TieheadlightcabletoIowerhandleswith theplasticcabletiesuppliedintheparts bagbythreadingthepointedendsofthe tiethroughthesquareendandpulling tightlyaroundtheheadfightcableand

handles.Seefigurebelow

NOTE:Onesideoftheplastictiehassmall notchesinit,whiletheothersideissmooth Thenotchedsidemustbeontheinsideof

theloopwhichisformedwhentheendsare puttogether..

Wire Harness Headlight Termina_ .__ Cable

Wire

Harness

Terrains

\Lower

Cable Tie

CONNECT REMOTE CHUTE . Push remote chute control lever into

"Chute Deflector

• Feed "Z" fitting through hole in remote chute bracket as shown in figure below.

• Snap remote chute control cable into remote chute bracket, see figure below

Chute Control / \ Bracket

Remote '__ _ (_ RemoteChute Bracket _._ _-_ote Chu,e

Up" _ position

Handle

• Connect "Z" fitting into remote chute control bracket as shown in figure below.,

• Push remote chute control lever into

"Chute Deflector Down" "_ position,

• Cut tie strap on chute deflector as shown in figure below

Chute Dellector

INSTALL MID-CHUTE ROD (set aside earlier)

• Carefully remove cotter pin and clevis pin from universal joint in the upper crank rod as shown in first figure below.

NOTE: If this removes the universal joint

and universal joint pin. Place universal joint into yoke of upper crank rod lining up large

holes., insert universal joint pin (ensure opening in universal joint pin is in line with small openings in universal joint)

Upper

Clevis Pin Rod

Universal Joint Pin

___//Cotter Pin

, Place yoke of open end of mid-crank rod

around universal joint in upper crank rod. Insert clevis pin through assembly and

secure with cotter pin, Spread ends of cotter pin to lock in place See figure

below,

Mid-Crank Red

:rsal

'Crank

Rod

°Z"Fittin_ t Cable

- Cut tie securing the lower crank rod to the chute rod bracket See second figure

below.

• Carefully remove cotter pin and clevis pin from universal joint in lower end of mid-crank rod as shown in figure below

NOTE: If this removes the universal joint and universal ioint pin Place universal joint into yoke of upper crank rod lining up large holes Insert universal joint pin (ensure

opening in universal joint pinis in line with

small openings in universal joint)

"--..._"_"_.._ UniversalJoin! Pin

Lower E__-_,/_Universal Joint

Cran_

• Slide universal joint in mid*crank rod into yoke of lower crank rod Insert clevis pin

through assembly and secure with cotter pin,, Spread ends of cotter pin 1o lock in

place, See next figure

Crank Rodt_.

CONNECT CONTROL CABLES

• Remove wrap from upper handle which was used to protect clutch levers

NOTE: If control cables have become unattached from motor mount frame,

reconnect cables as shown below Traction drive Auger drive

spring (Long) spring (Short)

Auger drive

spring cable

. Connect control cables to control lever

as shown in figure below

NOTE: The control cables attached to the auger clutch lever and traction clutch lever

may need to be adjusted before you use

your snow thrower

'Z" Fitting

For instructions on checking or adjusting the control cables, (See To Adjust Clutch Corn

trol Cables paragraph on page 19)

• Rot! the snow thrower off the skid by pulling on the handle.

• Properly dispose ol discarded packing

INSTALL SHIFTER ROD

(set aside earlier)

• Place speed shifter lever into sixth gear position

. Insert speed control rod (the end with the

90'_bend) into the speed select bracket lower hole. see next figure

• Attach speed control rod to the speed se- lect bracket with one flatwasher and one

cotter pin found in parts bag, see next figure

Viewlrorn theleft side o! unit

ixth gear position

Speed Select Bracket

Speed Control Rod

spring lever

• Move speed shifter lever into Rlposition

• Remove lockwasher and nut from ball joint, see next figure

Attachballjointtospeedselectleverwith

tockwasherandnut,thentightenSee figurebelow.Thespeedcontrolrodand balljointhavebeenpreadjustedatthe factoryandshouldnotrequirereadjust-

ment.

Speed

Control

Rod-....._

_'--BallJoint

__,!e peed

e_ect

vet

NOTE: Your snow thrower is equipped ,with

height adjust skids (see second figure on page 5) on the outside of the auger housing

To adiust the skid height for different

conditions, (see To Adjust Skid Height para-

graph on page 18),

KNOW YOUR SNOW THROWER

READ THIS OWNER'S MANUAL AND SAFETY RULES BEFORE OPERATING YOUR SNOW THROWER Compare the illustrations with your SNOW THROWER to familiarize yourself with the location of various controls and adjustments Save this manual for future

reference

,i CHECKLIST

Before you operate your new snow thrower,

to ensure that you receive the best pedor-

mance and satisfaction from this quality product, please review the folbwing

checklist: v" A_Iassembly instructions have been

completed

,# The discharge chute rotates freely 4" No remaining loose parts in carton,

except for extra shear bolt assembly parts,

While learning how to use your snow thrower, pay extra attention to the follow{rig important items:

JJ Engine oil is at proper level J,I Make sure gas tank is filled properly

with clean, fresh, unleaded gasoline

J,f Become familiar with all controls-their

location and function Operate controls

before starting engine

Engine Choke Of! Run

Auger Drive Clutch

Discharge Chute Chute chute-Right Deflector Defleclor Up

The operation of any snow thrower can result in foreign obiects being thrown into the eyes, which can result in severe eye damage Always wear safety glasses or eye shields while operating the snow thrower

We recommend standard safety glasses or a wide vision safety mask for over your glasses, availabte at Sears Retail Stores or Service Centers

Fast Slow

Forward Reverse Discharge

Down

Stop Fuel Oil

chute-Left

Primer Engage Traction Button Drive

Clutch

Ignition Key

insert to run

pu_lout

to stop

Ignition

Control

Electric

Speed Shifter Lever

Remote Chute Contrei

Auger Drive

Button

Auger

Drive Lever

arge

Chute

Height Adit

Auger Drive Lever - Starts and stops the auger and impeller (snow gathering and throwing),

Traction Drive Lever - Propels the snow thrower forward and in reverse

Headlight - Turns on whenever engine is

running,

Speed Shifter Lever - Selects the speed of snow thrower (6 speeds forward and 2 speeds reverse)

Crank Assembly - Changes the direction of snow throwing through the discharge chute,

Chute Deflector - Changes the distance the snow is thrown

Discharge Chute - Changes the direction the snow is thrown,

Choke Control - Used to start a cold en- gine,

Height Adjust Skids - Adjusts the ground clearance of the auger housing,

Ignition Key - Must be inserted to start the engine

Primer Button - Injects fuei directly into the carburetor mani!old for fast starts in cold

weather, Recoil Starter Handle - Starts the engine

manually, Throltte Control- Controls the engine

speed, Electric Starter Button - Used to start the engine using the 120 V electric starter,

Remote Chute Controt Lever- Push for- ward to discharge snow high and far, Pull

remote lever back to discharge snow down Shear Bolts - Are special bolts that are de-

signed to break (to protect the machine) if an object becomes lodged in

the auger housing Use of a harder bolt will destroy the protection provided by the shear bolt.

:r Bolt

Z_ CAUTION: Read owner's manual before operating machine Never direct discharge

toward bystanders Release the auger control bar and stop the engine before unclog-

ging discharge chute or auger housing and before leaving the machine,

HOW TO USE YOUR SNOW THROWER

TO STOP YOUR SNOWTHROWER

• To stop throwing snow, release the auger drive lever (see figure below)

• To stop the wheels, release the traction drive lever

- To stop the engine, push the throttle con- trol lever to off and pull out (DO NOT TURN) the ignition key, see figure on

page 10

Traction Drive Lever AugerDrive Lever TO CONTROL SNOW DISCHARGE

• Turn the crank assembly to set the direc- tion of the snow throwing.

• Adjust snow chute deflector to set the distance Push remote lever forward to

discharge snow down Putt remote lever back to discharge snow high and far See figure below

- Engage the traction drive lever as shown in first figure on this page, left hand As

the snow thrower starts to move, maintain

a firm hold on the handles, and guide the snow thrower along the clearing path Do

not attempt to push the snow thrower.

• To move the snow thrower backward, move the speed shifter lever into first or

second reverse and engage the traction

drive lever (left hand)

IMPORTANT: Never move the speed shifter

lever while the traction lever is down

TO THROW SNOW

• Push down the auger drive lever, see first figure on this page

• Release to slop throwing snow

TO USE WHEEL LOCKOUT PIN

• The left hand wheel is secured to the axle with a klick pin, see figure below, This

unit was shipped with this klick pin in the locked position (klick pin through hole in

wheel),

2-Wheel Drive

Locked Posilion

TO MOVE FORWARD AND

BACKWARD

To shift, release the traction drive lever and move the speed shifter lever to the

speed you desire Ground speed is deter-

mined by snow conditions Seiect the

speed you desire by moving the speed shifter lever into the appropriate area on the control panel

Speeds 1, 2 - Wet, Heavy, Extra Deep Speed 3 - Light

Speed 4 - Very Light Speeds 5, 6 -Transport only

• For ease of maneuverability in light snow conditions, disconnect the ktick pin from

the wheel locked position and push into the single wheel drive position (klick pin

through axle hole only), see next figure

NOTE: Make sure that the klick pin is in the single wheel drive position, through axle only and not through the hole in wheel

Klick Pin

Single Wheel Drive

Unlocked Position

BEFORE STARTING THE ENGINE

• If the snow thrower must be moved with- out the aid of the engine, it is easier to pull

the snow thrower by the handles rather than pushing.

• Before you service or start the engine, fa- miliarize yourself with the snow thrower.

Be sure you understand the function and location of all controls.

NOTE: Check tension of clutch cables be- fore starting the engine (See To Adjust The

Control Cables paragraph on page 19).

• Be sure that all fasteners are tight.

- Make sure the height adjust skids are properly adjusted (See To Adjust Skid Height paragraph on page 18).

- Check tire pressure (14 to t7 pounds)_

See side of tire for maximum inflation. Do

not exceed listed maximum pressure

FILL OIL

This snow thrower was shipped with a con- tainer of 5W30 motor oil. This oil must be

added to the engine before operating, Re- move the of! fill cap/dipstick and fill the crank

case to (FULL) line on dipstick (26 ounces) (see figure below),

OilFilltDipstick ,,

"_' '_O1' t7 NOTE: Oil levelmusl be

NOTE: Engine may already contain some residual oil. Check frequently when fill-

ing the crankcase. Do not over fill,

Tighten the fill cap/dipstick securely each time you check the oil level

FILL GAS WARNING: Experience indicates that alco-

hol blended fuels (called gasohol or those

using ethanol or methanol) can attract mois- ture which leads to separation and formation of acids during storage. Acidic gas can damage the fuel system of an engine while

in storage. To avoid engine probtems, the fuel system

should be emptied before storage for 30 days or longer,.Start the engine and let it

run until the fuel lines and carburetor are empty Use the carburetor bowl drain to

empty residual gasoline from the float cham-

ber Use fresh fuel next season (See Storage instructions on page 23 and 24 for additional information)

NOTE: Oil must be changed after the first 2 hours of operation to extend engine life.

For extreme cold operating conditions of 0°F and below, use a partial synthetic 0W30

motor oil for easier starting Never use engine or carburetor cleaner

products in the fuel tank or permanent dam- age may occur Fill the fuel tank with clean, fresh, unleaded

grade automotive gasoline. Be sure that the container you pour the gasoline from is clean and free from rust or other foreign par- ticles, Never use gasoline that may be stale from long periods of storage in the con-

tainer.

CAUTION: Gasoline is flammable

and caution must be used when han- dling or storing it. Do not fill fuel tank while snow thro_ver is running, when it is hot, or when snow

thrower is in an enclosed area

Keep away from open flame or an electrical

spark and DO NOT SMOKE while filling the fuel tank,

Never fill the tank completely. Fill the tank to within 1/4"- 1/2" from the top to provide space for expansion of fuel

Always fill fuel tank outdoors and use a fun- nel or spout to prevent spilling, Make sure to wipe up any spilled fuel before

starting the engine, Store gasoline in a clean, approved con-

tainer and keep the cap in place on the con- tainer,

TO STOP ENGINE

, To stop engine, move the throttle control

lever to _ (STOP) position and remove key Keep the key in a safe place. The

engine will not start without the key. NOTE: DO NOT turn key.

TO START ENGINE (Electric Starter) Be sure that the engine has sufficient oil.

The snow thrower engine is equipped with a

120 volt A C. electric starter and recoil starter. Before starting the engine, be cer- tain that you have read the following infor-

mation:

.4k CAUTION: This starter is equipped ZJ_

with a three-wire power cord and plug and is designed to operate on 120 volt AC household current It must be properly

grounded at all times 1oavoid the possibility of electrical shock which may be injurious to operator, Follow all instructions carefully as

set forth in the "To Start Engine" section Determine that your house wiring is a three- wire grounded system, Ask a licensed elec-

trician if you are not sure If your house

wire system is not a three-wire system, do not use this electric starter under any condi-

tions. If your system is grounded and a three-hole receptacle is not available at the

point your starter will normally be used, one should be installed by a licensed electrician When connecting I20 volt AC power cord, always connect the cord to the switch box

on the engine first, then plug the other end

into the three-hole grounded receptacle. When disconnecting power cord, always unplug the end in the three-hole grounded receptacle first

COLD START

• Be sure the auger drive and traction drive

levers are in the disengaged (released) position.

• Move the throttle control to '_ (FAST)

position See figure on page 10

• Remove the keys from the plastic bag

Insert one key into the ignition slot. Be

sure it snaps into place, DO NOT TURN KEY Keep the second key in a safe

place.

• Rotate the choke knob to (FULL) choke

position, See figure on page 10,

• Connect the power cord to the switch box

on the engine.

• Plug the other end of the power cord into a three-hole, grounded !20 volt A C receptacle,

o Push the primer button while covering the

vent hole as follows: (Remove finger from primer blitton between primes) See figure on page I0 for tocalion,

Do not prime if temperature is above 50°F,

Two times if temperature is 50°F to t5°F., Four times if temperature is below 15_F

• Push clown on the starter button until the engine starts, Do not crank lor more than

10 seconds at a time. This electric starter is thermally protected, Ifoverheated it will

stop automatically and can be restarted only when il has cooled to a safe temperature (a wait ot about 5 to 10 minutes is required),

• When the engine starts, release the starter button and slowly rotate the choke to (OFF) position, If the engine falters, rotate the choke to(FULL) and then

gradually to (OFF)

• Disconnect the power cord from the receptacle first and then from the switch box on engine

NOTE: Allow the engine to warm up for a few minutes because the engine will not de- velop full power until it reaches operating temperature_

• Run the engine al full throttle '_ (FAST) when throwing snow.

TO START ENGINE (Recoil Starter) Be sure that the engine has sufficient oil

The snow thrower engine is equipped with a recoil starter.. Belore starting the engine, be

certain that you have read the following in- tormation:

COLD START

. Be sure the auger drive and traction drive

levers are in the disengaged (released) position,

• Move the throttle control to '_ (FAST) position See figure on page 10 for loca-

tion

• Remove the keys from the plastic bag In- sert one key into the ignition slot, Be sure it snaps into place. DO NOT TURN KEY Keep the second key in a safe place

• Rotate the choke contro! to (FULL) choke position See figure on page t0

• Push the primer button, see figure on page 10, while covering the vent hole as

follows: (Remove linger from primer but-

ton between primes)

Do not prime if temperature is above 50oF

Two times il temperature is 50_F to 15°E Four times if temperature is below 15°F,

• Pull the recoil starter handle rapidly. Do not allow the handle to snap back, but at- low it to rewind slowly while keeping a

firm hold on the starter handle

• Astheenginewarmsupandbeginstoop- erateevenly,rotatethechokecontrol slowlytothe(OFF)positionIftheengine falters,returnto(FULL)choke,then slowlymovetothe(OFF)position

NOTE:Allowtheenginetowarmupfora

fewminutesbecausetheenginewillnotde- velopfullpoweruntilitreachesoperating

temperature

• Runtheengineatfullthrottle._ (FAST)

when throwing snow

WARM START

If restarting a warm engine after a short shutdown, leave choke at (OFF) and do not push the primer button. If the engine fails to

start, follow the Cold Start instructions above,

FROZEN RECOIL STARTER

If the starter is frozen and wilt not turn

engine: . Pull as much rope out of the starter as

possible,

• Release the starter handle and let it snap

back against the starter.

Ifthe starter still fails to turn engine, repeat the two previous steps until the starter en-

gages Then continue with the directions for coJd start

To help prevent possible freeze-up of recoil starter and engine controls, proceed as fol- lows after each snow removal job

• With the engine running, putt the starter

rope hard with a continuous full arm stroke three or four times,, Pulling of starter rope will produce a loud clattering

sound This is not harmful to the engine or starter

• With the engine not running, wipe all snow and moisture from the carburetor

cover in area of control levers, Also move throttle control, choke control, and starter

handle several times

_ CAUTION: Never run engine indoors

or in enclosed, poorly ventilated areas.

Engine exhaust contains carbon monoxide, an odorless and deadly gas, Keep hands, feet, hair and loose clothing away from any

moving parts on engine and snow thrower, WARNING: Temperature of muffler and

nearby areas may exceed I50 ° F Avoid these areas

DO NOT allow children or young teenagers to operate or be near snow thrower while it

is operating,

Z_ CAUTION: Do no attempt to remove

any item that may become lodged in

auger without taking the following precau- tions:

• Release auger drive and traction drive levers.

- Move Ihrottle lever to stop position.

• Remove (DO NOT TURN) ignition key o Disconnect spark plug wire . Do not place your hands in the auger or

discharge chute, Use a pry bar,

SNOW THROWING TIPS

• For maximum snow thrower efficiency in removing snow, adjust ground speed, NEVER the throttle Go slower in deep, freezing, or wet snow,, If the wheels slip, reduce forward speed The engine is de- signed to deliver maximum performance

at full throttle and should be run at this power setting at all times. Most efficient

snow blowing is accomplished when the snow is removed immediately after it falls,

• For complete snow removal, slightly over- lap each path previously taken, Use more overlap in deep snow to prevent overload- ing

• The snow should be discharged down

wind whenever possible In windy condi- tions, lower the chute deflector to direct

discharged snow close to the ground, where it is less likely 1oblow into un-

wanted areas

- For normal usage, set the skids so that the scraper bar is t/8" above the skids

For extremely hard-packed snow sur- faces, adjust the skids upward so that the scraper bar touches the ground.

• On gravel or crushed rock surfaces, set the skids at 1-t/4" below the scraper bar (See To Adjust Skids Height paragraph on

page 18) Stones and gravel must not be picked up and thrown by the machine,

• After the snow throwing job has been completed, allow the engine to idle tora

few minutes, which will melt snow and ac- cumulated ice off the engine

- Clean the snow thrower thoroughly after each use

• Remove ice and snow accumulation and

all debris from the entire snow thrower, and flush with water (if possible) to re-

move all salt or other chemicals, Wipe

snow thrower dry,

CUSTOMER RESPONSIBILITIES

SERVICE SCHEDULE SERVICE RECORDS DATES

Fill in dates as

you complete

regularservice

Tigh!en AIJ Screws & Nuts ,v" , _ J ........

Lubricate Pivo[Poinls p,," pJ LubricaEeAuger Shaft iSee = =

Shear Boll Replacement _ t,"

Lubricale Disc Drive PIate Zerk _ Check Spark Plug ,_ Check Engine Oil Lever it' p,_

Change Engine Oil _ _ Check FueI ;I'

Drain Fuei _,_

Check Auger Clutch Cabte _ ...........

Adjustment (See Cabie Adj) Check Traction Clutch Cable

Adjustment (See Cable Adj) _ Check Drive Belts _ _

PRODUCT SPECIFICATIONS

HORSE POWER: 10 HP

A.er BeforeA_ EVo_E_or_E_e_ E_ch Before

iirst 2 Each Needed: 5 t0 25 Season Storage Hours Use Hours Hours Hours

......... = ......

.... = ....

................... = ; ;

• = - . .......rE .. ! _ ! [,,

Some adjustments will need to be made pe- riodically to properly maintain your snow

thrower

DISPLACEMENT: 21 82 cu in,

GASOLINE CAPACITY: 4 quart

(unleaded)

OIL (26 oz, Capacity) : 5W-30 SPARK PLUG: Champion RJ19LM

(Gap 030) or Equivalent

VALVE CLEARANCE: Intake: 0 !0 In,

Exhaust: .010 tn,

GENERAL RECOMMENDATIONS

The warranty on this snow thrower does not cover items that have been subjected to op-

erator abuse or negligence To receive full value from the warranty, the operator must

maintain the snow thrower as instructed in this manual The above chart is provided to

assist the operator in properly maintaining the snow thrower,

LUBRICATION CHART

Lubricate Disc Drive

Plate Zerk

with a Hi Temp EP

Moiy Grease

Lub_'icale the Auger Shaft Coat with a clinging _ype grease

such as Lubriplate or fiber impregnated grease

SNOW THROWER

AFTER FIRST USE

• Check for any loose or damaged parts after each use

• Tighten any loose fasteners

• Check and maintain the auger,

AFTER EACH USE

• Remove all snow and slush off the snow

thrower to prevent freezing of auger or controls

• Check controls to make sure they are functioning properly

• I!any parts are worn or damaged, replace immediately.

SNOW TH ROWER

LUBRICATION- EVERY 10 HOURS

• Auger Shaft- Using a hand grease gun, lubricate the auger shaft zerk fittings (See

figure below) every ten (10)operating

hours. Each time a shear bolt is replaced

(See To Replace Auger Shear Bolt on page 22), the auger shaft MUST be

greased,.

• For storage or when replacing shear bolts, remove shear bolts and lubricate

auger shaft zerks Rotate augers several times on the shaft and reinstall the shear

bolts,

, See Lubrication Chart diagram on page

15 for lubrication points and type of lubri-

cant,

LUBRICATION - EVERY 25 HOURS

• Lubricate Disc Drive Plate ever,/twenty- five (25) hours and at the end of the sea- son and/or before storage

To Lubricate: , Position speed selector lever infirst gear.

,' Stand the snow thrower up on the auger

housing end,

Friction

Wheel

(Require No

LubricatiS'n)

Friction

Shaff

Wheel Grease

Bearing

Place coin in gap between lriclion

wheel and disc drive

I }

pta_e

should be v_sibte

E_:_}--Grease Zerk

• Remove the bottom panel (see second figure on page 21 )

o Turn disc drive plate clockwise by hand

until grease zerk is clearly visible at front

center. See next figure,

• Place a coin or (a shim of equal thick-

ness) between the rubber friction wheel and disc drive plate to prevent rubber fric-

tion wheel contacting the drive disc,

• To grease zerk, use a hand grease gun,

lubricate with a Hi Temp EP Moly grease See inset of figure above DO NOT over

fill or allow grease to come in contact with the disc drive plate or friction wheel or

damage will result Fill zerk only until grease becomes visible be}ow bearing as-

sembly located under grease zerk see in- sert above,,

IMPORTANT: Remove coin and ensure that agap exists between friction wheel and disc

drive p_ate. NOTE: Clean all excess grease found on

friction disc hub

CAUTION: Do not allow grease to contact

friction wheel and disc drive plate

LUBRICATION- BEFORE STORAGE

• Remove both wheels, grease (any auto- motive type grease) both axles, see figure

below, and replace wheels Do this at least once a year and/or prior to storage

Disc

grease

LUBRICATION

• HexShaftandGears-Hexshaftand gearsrequirenolubrication.Allbearings

andbushingsarelifetimelubricatedand requirenomaintenance

NOTE:Anygreasingoroilingoftheabove componentscancausecontaminationof

thefrictionwheel,tfthediscdriveplateor frictionwheelcomesincontactwithgrease oroil,damagetothefrictionwheelwillre-

sult. Shouldgreaseoroilcomeincontactwith

thediscdriveplateorfrictionwheel,besure

tocleantheplateandwheelthoroughly.

NOTE:Forstorage,thehexshaftand gearsshouldbewipedwith5W-30motoroil

topreventrustingSeefirstfigureonthis page.

• AugerGearBox-Theaugergearboxis lubricatedatthefactoryandshouldnot

requireadditionallubrication.Ifforsome reasonthelubricantshouldleakout,orif

theaugergearboxhasbeenserviced,

add Lubripfate No. 630-AA or equivalent. Maximum 3-1/4 ounces should be used

Remove filler plug as seen in figure below once a year. If grease is visible, do not add.. If grease is not visible, use a piece

of fine wire like a dipstick, to check if there is grease in the gearbox. Add grease if necessary Reinstall gear box

filler

OIL RECOMMENDATION

Only use high quality detergent oil rated with API service classitication SG. Select

the oil's viscosity grade according to your

expected operating temperature: NOTE: For extreme cold operating condi-

tions of 0° and below, use a partial synthetic 0W30 motor oil for easier starting.

Change the oil after first two (2) hours of operation, every twenty-five (25) hours

thereafter, and at the beginning of each

season

• Position the snow thrower so that the oil drain plug is at the lowest point on the en-

gine.. Remove the oil drain plug and the oil fill cap/dipstick. Drain the oil into a suit-

able container Oif will drain more freely when warm.

• Replace the oil drain plug and tighten se- curely.

SPARK PLUG

• Make sure that the spark plug is tight- ened securely inlo the engine and the spark plug wire is attached Io the spark plug

, II a torque wrench is available, torque

plug to 18 to 23 foot pounds.

• Clean the area around the spark plug base before removal to prevent dirt from entering the engine

• Clean the spark plug and reset the gap periodically at 030 inch.

r Box Filler

Plug

ENGINE

LUBRICATION Check the crankcase oil level (see figure be-

low) before starting the engine and after each five (5) hours of continuous use Add

S.AE 5W30 motor oi! as needed Tighten lill cap/dipstick securely each time you

check the oil level

CAUTION: Always disconnect the

spark plug wire and tie back away from

the plug before making any adjustments or repairs

TO ADJUST SKID HEIGHT

This snow thrower is equipped with two height adjustment skids, located on the out-

side of the auger housing (see figure be-

low) These skids elevate the front of the

snow thrower

Auger Housing

Height Adjust Skids

Skid Mounting N

For normal hard surfaces, adjust the skids as lollows:

• Check tire pressure (14 to I7 pounds). See side ol tire for maximum inflation. Do

not exceed maximum pressure on side of

tire,

- Place the extra shear bolts supplied (found in parts bag) under each end of

the scraper bar near but not under the skid

• Loosen the skid mounting nuts (see fig- ure above) and adiust the skids up to

bring the front of the snow thrower down

• Re-tighten the mounting nuts

• Set the skid on the other side at the same height

For rocky or uneven surfaces, adjust the skids as follows:

• Raise the front o_the snow thrower by moving the skids down This will help pre-

vent rocks and other debris from being picked up and thrown by the auger

NOTE: Be sure that snow thrower is set at same height on both sides

TO ADJUST SCRAPER BAR

After considerable use, the metal scraper bar will have a definite wear pattern The scraper bar in coniunclion with the skids should always be adjusted to allow t/8" be-

tween the scraper bar and the sidewalk or area to be cleaned, The scraper bar may

have to be returned to its original lower set- ting to maintain the original performance

level To adjust:

• Position the snow thrower on a level sur- face.

• Make sure both tires are equa!ly inflated

• Loosen the carriage bolts and nuts secur- ing the scraper bar to the auger housing

• Adjust the scraper bar to the proper posi- tion

• Tighten the carriage bolts and nuts, mak- ing sure that the scraper bar is parallel with the working surface

- For extended operation, the scraper bar may be reversed It the scraper bar must be replaced due to wear, remove the car- riage bolts and nuts and install a new scraper bar

/_k CAUTION: Be certain to maintain

proper ground clearance for your par- ticular area to be cleared Objects such as gravel, rocks or other debris, if struck by the impeller, may be thrown with sufficient force

to cause personal injury, property damage or damage to the snow thrower

TO ADJUSTTHE CLUTCH CONTROL CABLES

Periodic adjustment of the cables may be required due to normai stretch and wear on the bells To check for correct adiustment,

disconnect "Z" Fitting at clutch lever, move clutch lever to the full forward position, just contacting the plastic bumper The control cables are correctly adjusted when the cen-

ter of the "Z" fitting is between the center and top of the hole and there is no droop in the cable (see figure below), If adjustment is

necessary:

Control Lever

be in full

Plastic torward position

Bumper (Just Contacling

Plastic Bumper)

when checking

• Remove fuel from tank, and stand blower on end,

• Pull rubber boot off the top of the spring Push the cable through the spring (see figure below) to expose the threaded por-

tion of the cable

TO ADJUST BELTS

Belts stretch during normal use If you need to adjust the belts due to wear or stretch, proceed as follows:

AUGER DRIVE BELT If your snow thrower will not discharge

snow, check the control cable adjustment, tf it is correct, then check the condition of the

auger drive belt, it may be loose or dam- aged If it is damaged, replace it (See To Replace Belts paragraph on page 20). If the

auger drive belt is loose, adjust as follows:

• Disconnect the spark plug wire_ , Remove the belt cover (See second

figure on page 20)

• Loosen the nut on the auger idler pulley (See figure below) and move the pulley

toward the belt about t!8".

• Tighten the nut

Traction

Traction Drive Belt Drive Drive Belt Idler

\ Belt Guide _y

Belt Guide (Right

Left Hand)

,Loosen nut

,tare end

Locknut

• Hold the square end of the threaded por- tion with pliers and adjust the tocknut in or

out until the excess slack is removed,

• Pull the cable back through the spring and connect the cable.

• Do the same for the other lever cable, if needed.

NOTE: Whenever the traction drive or au- ger belts are adjusted or replaced, the

cables will need to be adjusted_

Jger Idler

Pulley

- Press the auger drive lever_Check the tension on the belt (opposite auger idler pulley) The belt should deflect about !12" with moderate pressure (See figure below)

NOTE: You may have to move the auger idler pulley more than once to obtain the

correct tension

.r_ Drive Pulley

Auger ldter ---"-{,..,_ ..._,_'-t/2 inch

Engaged

Pulley _Deflection

• Replace the belt cover.

• Check the clutch control cable adjustment

• Reconnect the spark plug wire

TRACTION DRIVE BELT

The traction drive belt (see figure below) has constant spring pressure and does not

require adjustment,

• Replace the traction drive belt if it is slip- ping (see To Replace Belts paragraph on this page),

TO REPLACE BELTS The drive belts on this snow thrower are of

special construction and should be replaced with original equipment belts available from

your nearest SEARS Store or Service Cen-

ter.. You will need the assistance of a second person while replacing the belts, Drain the gasoline from the fue! tank by re-

moving the fuel line at the carburetor,. Drain the gas into a container and reinstall the rue!line,

/_. CAUTION: Drain the gasoline out-

doors, away from the fire or flame,

AUGER DRIVE BELT If your snow thrower will not discharge

snow, and the auger drive belt (see figure below for location) is damaged, replace it as follows:

Auger Drive Belt

Pulley er Drive

Traction Pulley Drive Bell

Bett Guide (Right Hand) (Left Hand)

Auger Idler

Pulley

- Disconnect the spark plug wire

• Remove the belt cover (see next figure ).

Bert

1!4X t/2 Ihchself4apping Screw

• Loosen the belt guides (see first figure on this page) and pull away from the auger drive pulley

. Remove belt from auger drive pulley, , Remove top two bolls that secure auger

housing to motor mount frame, Loosen bottom two bolts Auger housing and mo-

tor mount frame will separate, hinged by bottom two bolts (see second figure on

page 21)

• Remove old belt from the auger drive pul- ley.,

• Position new belt on auger pulley

, Replace top two bolts, and re4ighten bot-

tom two bolts

• Adjust the belt guides (see To Adjust The Belt Guides paragraph on page 21),

• Reinstall the belt cover

, Reconnect the spark plug wire,, TRACTION DRIVE BELT

tt your snow thrower will not move forward, check the traction drive belt (see first figure

on this page) for wear (Check other causes also in the Trouble Shooting Points section).

If the traction drive belt needs to be re- placed, proceed as follows:

- Disconnect the spark plug wire

• Remove the belt cover (see figure above),

• Loosen the belt guides and pull away from auger drive pulley (see first figure

on this page)

• Remove auger drive belt from auger pul-

ley (see first figure on this page)

• Pull the traction drive bell idler pulley

away from the traction drive belt (see first figure on this page)

• Remove the traction drive belt

• Position new traction drive belt onto trac-

tion pulley

• Pulf idler pulley away from belt, allowing

belt to be positioned onto auger pulley

• Release idler pulley.. Ensure idler pulley is properly engaged with bell

. Reinstall auger drive belt

• Adjust the belt guides and tighten mount- ing screws (see To Adjust The Belt

Guides paragraph on this page)

- Adjust idler on auger bell

- Reinstall the belt cover

, Reconnect the spark plug wire.

TO ADJUSTTHE BELT GUIDES

There are two belt guides on your snow thrower, a left and right After you replace

the traction drive belt, you need to adjust one or both of the belt guides. Proceed as follows for each belt:

- Disconnect the spark plug wire.

- Remove the belt cover (see second fig- ure on page 20)

. Engage the auger drive clutch lever

• Measure the distance belween the belt guides and the belt (see figure below).

The distance should be 3/32" for each guide.

Pulley

3/32 iuide

Bel! Gu r) (Right Inch

Auger

• Disconnect the spark plug wire.

• Drain the gasoline from the gas tank

• Stand snow thrower on the auger housing end.

• Remove the bottom panel (see figure be-

low),

RemoveTop Bolts (EachSide)

Housing

Leo botlom bolls (each side) (Bottom View)

• Position the shifter lever in first (1) gear

• Note the position of the friction wheel on the disc drive plate The right outer side of the disc drive plate should be 3" from the

center of the friction wheel (see figure be- low)

Wheel

• If adjustment is necessary, loosen the bell guide mounting bolts. Move the bell

guides to the correcl position Tighten the mounting bolls,

, Reinstall the belt cover

• Reconnect the spark plug wire.

TO ADJUST THE FRICTION WHEEL

If the snow thrower will not move forward,

you need to check the traction drive belt, the traction drive cable or the friction wheel If

the friction wheel is damaged, it will need to be replaced (see the To Replace Friction

Wheel paragraph on page 22) 1(the friction wheel is not worn, check the adjustment, as

follows:

, i

If adiustment is necessary:

• Loosen nut "A" on the speed select rod. Remove the ball joint by removing nut "B" from shift yoke assembly. Lengthen or

shorten the rod by turning the adaptor to

obtain the correct friction wheel position

(see figure below)

, Reinstall the ball joint and nut "B" Tighten

nut "A".

• ReinstaIlthe bottom panel.

select "\\\

Rod \<_

Nut"A"-._

Adapter...-..."_

Ball Joint J

TO REPLACE FRICTION WHEEL

tf the snow thrower wilt not move forward, and the frict{on wheel is worn or damaged, you need to replace it as follows: (First allow

the engine to cool),.

• Drain the gasoline from the fuel tank by removing the fuel line at the carburetor..

Drain the fuel in a container and reinstall the fuei line.,

Z_ CAUTION: Drain gasoline outdoor

away from fire or flame.

• Disconnect the spark plug wire.

- Stand the snow thrower up on the auger housing end

• Remove the bottom panel (see second figure on page 21).

• Remove the three (3) _asteners securing the friction wheel to the hub (see figure

below),

Friction Wheel', r-.

"_ ,,,Lockwasher

Bolt _ Lockwasher

• Remove the four bolts securing the bear- ing plates (both sides), (see second fig- ure on this page).

• Remove right side bearing plate, Leave hex shaft in original position

• Remove friction wheel from hub. Slip fric- tion wheel off hex shaft towards right

side

- Slip new friction wheel onto hub with re- cessed or cupped end away from hub

(see figure above).,

• Install bearing plates to original position. Ensure hex shaft is engaged with both

bearing p_ates,

• Secure bearing plates, using bolts re*

moved earlier.

• Secure friction wheel to hub using fasten- ers removed earlier Ensure hex shaft

turns freely

Bearing Plate Bolts

Bearin Plate

Fasteners (Bolts.

and nuts).,

i .... i

i //

Auger

NOTE: Ensure friction wheel and triction disc are free from grease or oil

. Replace bottom panel

• Lower the snow thrower onto the tires,

TO REPLACE AUGER SHEAR BOLT

The augers are secured to the auger shaft with special bolts (see figure below) that are designed to break (to protect the machine)

if an object becomes lodged in the auger

housing Use of a harder bolt will destroy the

protection provided by the shear bolt, IMPORTANT: To ensure satety and perfor-

mance levels, only original equipment shear bolls should be used When replacing shear bolts, be sure to replace shear bolt spacers

• To replace a broken shear bolt, proceed as follows:

• Move the throttle to 1_ (STOP) and turn off all controls

• Disconnect the spark plug wire Be sure all moving parts have stopped..

• Lubricate the auger shaft zerk fitting (See the Maintenance section on pages 15-

17).

+ 50 hidden pages

Craftsman 536882650 Owner’s Manual

Specifications and Main Features

Frequently Asked Questions

User Manual