Craftsman 358794771 Owner’s Manual

Operator's Manual

I CRRFTSMRN°I

25cc/1.5 cu.in. 2-Cycle 215 MPH/470 CFM

GASOLINE POWERED BLOWERNAC

Model No.

358.794771

• Safety

• Assembly

• Operation

• Maintenance

• Parts List

• Espar_ol, p. 20

WARNING:

Read and follow all Safety Rules and Operating Instructions before first use of this product.

For answers to your questions about this product:

Call 7 am-7 pm, Mon.-Sat., or 10 am-7 pm, Sun.

1-800-235-5878 (Hours listed are Central Time)

Sears, Roebuck and Co., Hoffman Estates, IL 60179 U.S.A.

545154710 Rev. 2 1/3/08 BRW

Warranty Statement 2 Storage 13 Identification of Safety Symbols 2 Troubleshooting Table 14

Safety Rules 3 Emissions Statement 15 Assembly 5 Parts List 17 Operation 8 Spanish 20

Maintenance 11 Parts and Ordering Back Cover

TWO YEAR FULL WARRANTY ON CRAFTSMAN@ GAS BLOWER When used and maintained according to the operator's manual, if this product fails

due to a defect in material or workmanship within two (2) years from the date of pur- chase, return it to any Sears store, Sears Service Center, or other Craftsman outlet in the United States for free repair (or replacement if repair proves impossible).

This warranty excludes spark plug and air cleaner, which are expendable parts that can wear out from normal use in less than two years.

This warranty applies for only 30 days from the date of purchase if this product is used for commercial or rental purposes. This warranty gives you specific legal rights, and you may also have other rights which vary from state to state.

Sears, Roebuck and Co., Hoffman Estates, IL 60179

_IWARNING: This unit can be dangerous! Careless or

improper use can cause serious injury.

Read your operator's manual carefully until you completely un- derstand and can follow all warnings and safety rules before

operating the unit. Failure to do so can result in serious injury. Save operator's manual.

violently. You can be blinded or injured. Always wear hearing

protection and safety glasses The blower can throw objects

marked Z87. Always wear heavy, long pants, long sleeves,

boots and g oves=

Hazard zone for thrown objects. Keep children, bystanders, and animals away from work area a

minimum of 30 feet (10 meters) when starting or operating unit. Do not point blower nozzle in the direction of people or pets.

-2-

Do not wear jewelry, loose clothing, or clothing with loosing hanging straps, ties, tassels, etc. They can

be caught in moving parts.

before cleaning or servicing.

I i_ O _ Always stop unit and disconnect spark plug

WARNING: Stop the engine before opening the vacuum inlet door. The

engine must be stopped and the impeller blades no longer turning to avoid serious

injury from the rotating blades. Gently tilt the handle of the screwdriver toward the back of the unit to release the latch while pulling up on the vacuum inlet cover with

'our other hand.

When using the vacuum attachment, the unit is designed to

pick up dry material such as leaves, grass, small twigs, and bits

of paper. Do not vacuum stones, gravel, metal, broken glass, etc., to ave d severe damage to the mpe er.

@ _r uWeAtt_eNulnNitGn'eFirre haaz2r dorNpVaet_2(iiX'ciP°cUrng rsSmt°rktng,aSpline

II WARNING: Failure to follow all Safety Rules and Precautions can re-

sult in serious injury.

KNOW YOUR UNIT

• Read your instruction manual care- fully until you completely understand and can follow all warnings and

safety rules before operating the unit.

f ames, or work that can cause sparks),

WARNING: The muffler is very hot during and after use. Do not touch the muffler, muffler guard, or surrounding surfaces, or allow combustible material such as dry grass or fuel to do so.

1@1

• Restrict unit to users who understand and will follow all warnings and safety

rules in this manual.

_liWARNING: Inspect area before

starting unit. Remove all debris and hard objects such as rocks, glass,

wire, etc. that can ricochet, be thrown,

or otherwise cause injury or damage during operation.

-3-

Use your unit as a blower for:

• Sweeping debris or grass clippings from driveways, sidewalks, patios, etc.

• Blowing grass clippings, straw, or leaves into piles, around joints, or be-

tween bricks.

Use your unit as a vacuum for:

• Picking up dry material such as leaves, grass, small twigs, and bits of

paper.

• For best results during vacuum use, operate your unit at high speed.

• Move slowly back and forth over the material as you vacuum. Avoid forc- ing the unit into a pile of debris as

this can clog the unit.

• Keep the vacuum tube about an inch above the ground for best results.

PLAN AHEAD

• Always wear eye protection when op- erating, servicing, or performing main- tenance on unit. Wearing eye protec-

tion will help to prevent rocks or debris from being blown or ricocheting into eyes and face which can result in

blindness and/or serious injury. Eye protection should be marked Z87.

• Always wear foot protection. Do not go barefoot or wear sandals.

• Always wear respirator or face mask when working with unit in dusty envi-

ronments.

• Secure hair above shoulder length. Secure or remove jewelry, loose

clothing, or clothing with loosely hanging straps, ties, tassels, etc.

They can be caught in moving parts.

• Do not operate unit when you are tired, ill, upset, or if you are under the

influence of alcohol, drugs, or medi- cation.

• Keep children, bystanders, and ani- mals away from work area a mini-

mum of 30 feet (10 meters) when starting or operating unit. Do not point blower nozzle in the direction of

people or pets.

HANDLE FUEL WITH CAUTION, IT IS HIGHLY FLAMMABLE

• Eliminate all sources of sparks or flame (including smoking, open flames, or work that can cause

sparks) in the areas where fuel is mixed, poured, or stored.

• Mix and pour fuel in an outdoor area; store fuel in a cool, dry, well ventilated

place; use an approved, marked con- tainer for all fuel purposes.

• Do not smoke while handling fuel or while operating the unit.

• Make sure the unit is properly as- sembled and in good operating

condition.

• Do not fill fuel tank while engine is

running.

• Avoid spilling fuel or oil. Wipe up fuel spills before starting engine.

• Move at least 10 feet (3 meters) away from fuel and fueling site be-

fore starting engine.

• Always store gasoline in a container approved for flammable liquids.

OPERATE YOUR UNIT SAFELY

_bWARNING: Stop the engine be- fore opening the vacuum inlet door. The

engine must be stopped and the impel- ler blades no longer turning to avoid se- rious injury from the rotating blades.

• Inspect unit before each use for worn, loose, missing, or damaged

parts. Do not use until unit is in proper working order.

• Keep outside surfaces free from oil and fuel.

• Never start or run engine inside a closed room, building or other un-

ventilated area. Breathing exhaust fumes can kill.

• To avoid static electricity shock, do

not wear rubber gloves or any other insulated gloves while operating unit.

• Do not set unit on any surface except a clean, hard area while engine is run-

ning. Debris such as gravel, sand,

dust, grass, etc. could be picked up by the air intake and thrown out through discharge opening, damaging unit,

property, or causing serious injury to bystanders or operator.

• Avoid dangerous environments. Do

not use in unventilated areas or

where explosive vapors or carbon

monoxide build up could be present.

• Do not overreach or use from unsta-

ble surfaces such as ladders, trees,

steep slopes, rooftops, etc. Keep firm footing and balance at all times.

• Never place objects inside the

blower tubes; always direct the blow- ing debris away from people, ani-

mals, glass, and solid objects such

as trees, automobiles, walls, etc. The force of air can cause rocks, dirt, or

sticks to be thrown or to ricochet which can hurt people or animals,

break glass, or cause other damage.

• Never run unit without the proper equipment attached. When using

your unit as a blower, always install

-4-

blower tubes. When using the op- tional vacuum kit, always install vac- uum tubes and vacuum bag assem-

bly. Make sure vacuum bag assem- bly is completely zipped.

• Check air intake opening, blower tubes, and vacuum tubes frequently,

always with engine stopped and spark plug disconnected. Keep vents

and discharge tubes free of debris which can accumulate and restrict

proper air flow.

• Never place any object in air intake opening as this could restrict proper air flow and cause damage to the unit.

• Never use for spreading chemicals, fertilizers, or other substances which

may contain toxic materials.

• To avoid spreading fire, do not use near leaf or brush fires, fireplaces,

barbecue pits, ashtrays, etc.

• Use only for jobs explained in this manual.

MAINTAIN YOUR UNIT PROPERLY _,WARNING: Disconnect spark

plug before performing maintenance except for carburetor adjustments.

• Have all maintenance other than the recommended procedures described

in the instruction manual performed by a Sears Service Center.

• Use only recommended Craftsman replacement parts; use of any other

parts may void your warranty and cause damage to your unit.

• Empty fuel tank before storing the unit. Use up fuel left in carburetor by

starting engine and letting it run until it stops.

• Do not use any accessory or attach- ment other than those recommended

by manufacturer for use with your unit.

• Do not store the unit or fuel in a closed area where fuel vapors can reach

sparks or an open flame from hot water heaters, electric motors or

switches, furnaces, etc.

• Store in a dry area out of reach of children.

SAFETY NOTICE: Exposure to vibra-

tions through prolonged use of gaso-

line powered hand tools could cause blood vessel or nerve damage in the

fingers, hands, and joints of people

prone to circulation disorders or abnor- mal swelling. Prolonged use in cold

weather has been linked to blood ves- sel damage in otherwise healthy

people. If symptoms occur such as numbness, pain, loss of strength,

change in skin color or texture, or loss of feeling in the fingers, hands, or

joints, discontinue the use of this tool

and seek medical attention. An anti-

vibration system does not guarantee the avoidance of these problems. Us-

ers who operate power tools on a con-

tinual and regular basis must monitor

closely their physical condition and the condition of this tool.

SPECIAL NOTICE: This unit is equipped with a temperature limiting

muffler and spark arresting screen

which meets the requirements of Cali- fornia Codes 4442 and 4443. All U.S.

forest land and the states of California,

Idaho, Maine, Minnesota, New Jersey, Oregon, and Washington require by law that many internal combustion en- gines be equipped with a spark arrest-

ing screen. If you operate in a locale

where such regulations exist, you are

legally responsible for maintaining the operating condition of these parts. Fail-

ure to do so is a violation of the law. Refer to the MAINTENANCE section for

information on maintenance of the muffler and spark arresting screen.

CARTON CONTENTS Check carton contents against the fol- lowing list.

Model 358.794771

• Blower

• Upper blower tube

• Lower blower tube

• High velocity nozzle

• Elbow tube

• Vacuum bag

• Upper vacuum tube

• Lower vacuum tube

• 2-Cycle engine oil

NOTE: It is normal for the fuel filter to rattle in the empty fuel tank.

ASSEMBLY

_WARNING: Stop engine and be

sure the impeller blades have stopped

turning before opening the vacuum in-

let door or attempting to insert or re- move the vacuum tubes, The rotating

blades can cause serious injury.

-5-

411 WARNING: If you receive your unit assembled, repeat all steps to en- sure your unit is properly assembled

and all fasteners are secure.

• A standard screwdriver is required for assembly.

BLOWER ASSEMBLY

BLOWER TUBE ASSEMBLY If you have already assembled your

unit for use as a vacuum, remove the vacuum tubes and collection bag.

1. Align the rib on the upper blower tube with the groove in the blower

outlet; slide the tube into place.

NOTE: Knob must be loose enough to

allow blower tube to be inserted in blower outlet. Loosen knob by turning

counterclockwise.

__ Blower Outlet

2= Secure the tube by turning the

knob clockwise.

3= Align the slots on the lower blower

tube with the tabs on the upper

blower tube.

6. To remove the tubes, turn the knob counterclockwise to loosen the

tubes; remove the tubes.

HIGH-SPEED NOZZLE ASSEMBLY

When greater air speed is desired, use the high-speed nozzle.

1. Align the slots on the nozzle with the tabs on the lower blower tube.

High-Speed Nozzle

Lower Blower

Tube

2. Slide the nozzle onto the lower blower tube.

3. Turn the nozzle clockwise until a click is felt to secure the nozzle to

the lower blower tube.

VACUUM ASSEMBLY

VACUUM BAG ASSEMBLY

1. Open the zipper on the vacuum bag and insert the elbow tube.

2. Push the small end of the elbow tube through the small opening in

the bag.

Elbow Tube

Rib

4. Slide the lower blower tube onto the upper blower tube.

5= Turn the lower blower tube clock-

wise until a click is felt to secure the lower blower tube to the upper

blower tube.

NOTE: When the upper and lower blower tubes are assembled together properly, the arrows on both tubes will

be aligned.

Opening

Small Opening NOTE: Make sure edge of the small opening is flush against the flared area

of the elbow tube, and the rib on the elbow tube is on the bottom.

3. Close the zipper on the bag. Make sure the zipper is closed completely.

4. Remove blower tubes from engine.

5= Insert the elbow tube into the blow-

er outlet. Make sure elbow tube rib is aligned with the blower outlet

groove.

-6-

6. Turn knob clockwise to secure el- bow tube.

VACUUM TUBE ASSEMBLY _,WARNING: Stop engine and be

sure the impeller blades have stopped turning before opening the vacuum inlet door or attempting to insert or remove

the vacuum or blower tubes. The rotat- ing blades can cause serious injury.

1. Insert the tip of a screwdriver into the latch area of the vacuum inlet.

Latch Area

Vacuum Inlet Cover

2. Gently tilt the handle of the screw- driver toward the front of the unit to

release the latch while pulling up on the vacuum inlet cover with your

other hand.

3. Hold the vacuum inlet cover open until upper vacuum tube is installed.

Vacuum

Inlet

Cover

Inlet

4. Align the tabs on the inside of the

vacuum inlet with the slots in the

upper vacuum tube.

Tab Slot

5. Push the upper vacuum tube into the vacuum inlet. Turn the tube counterclockwise until a click is felt

to secure the tube to the blower unit.

6. Align slanted end of lower vacuum tube as shown. Firmly push lower

vacuum tube into upper vacuum tube.

Slanted end of

lower vacuum tube

HOW TO CONVERT UNIT FROM

VACUUM USE TO BLOWER USE

1. Remove the elbow tube and vacu- um bag by turning the knob coun-

terclockwise to loosen the elbow tube.

2. Remove the vacuum tubes by turn- ing the tubes clockwise.

3. Close the vacuum inlet cover and make sure it is latched closed.

4. Reinstall the blower tubes (see BLOWER TUBE ASSEMBLY).

VACUUM BAG SHOULDER STRAP ADJUSTMENT

1. Hold the unit as shown with the muffler side facing away from your

body and clothes.

2. Pass the shoulder strap over your head and onto your right shoulder.

3. Extend your left arm toward the rear of the vacuum bag.

4. Adjust shoulder strap until the vacu- um bag/shoulder strap seam lies be- tween your thumb and index finger.

5. Make sure air flows freely from the elbow tube into bag. If bag is kinked, the unit will not operate

properly.

-7-

SHOULDER STRAP ATTACHMENT

(optional accessory #71-85783)

1. Pass the shoulder strap over your head and onto your left shoulder.

2. Snap the hook onto the retainer

(see following illustration).

BLOWER USE VACUUM USE

Retah_er _ _--_

__"---'_ "_--_ I Retainer

KNOW YOUR BLOWER

READ THIS iNSTRUCTiON MANUAL AND SAFETY RULES BEFORE OPERATING YOUR

UNIT. Compare the illustrations with your unit to familiarize yourself with the location of the various controls and adjustments. Save this manual for future reference.

MULCHING BLADES

Your blower is equipped with mulching blades as a standard feature. When using the vacuum attachment, the mulching blades automatically reduce debris at a

ratio of up to 16:1.

Throttle Position Lever

Upper Vacuum Tube

STOP Switch

Throttle Trigger

R°P X

Fuel Mix Fill Cap _,

Primer Bulb

STOP SWITCH

The STOP switch is used to stop the engine. To stop the engine, push and

hold the STOP switch in the STOP posi- tion until the engine stops.

Spark Plug

Upper Blower TubeStarter

Vacuum Handle

Elbow Tube

Lower Vacuum Tube

Lower Blower Tube High-

THROTTLE TRIGGER

The THROTTLE TRIGGER is used to se-

lect the desired engine speed.

-8-

Speed

Nozzle

THROTTLE POSITION LEVER

The THROlq-LE POSITION LEVER is de- signed to allow setting engine speed during blower use only. To avoid caus- ing damage to the unit, DO NOT at-

tempt to use the throttle position lever during vacuum use.

PRIMER BULB The PRIMER BULB removes air from the carburetor and fuel lines and fills

them with fuel. This allows you to start the engine with fewer pulls on the starter rope. Activate primer bulb by

pressing it and allowing it to return to its original position.

OPERATING TIPS

• While vacuuming or blowing debris,

hold the unit with the muffler side fac- ing away from your body and clothes

(see OPERATING POSITION below).

• To reduce the risk of hearing loss

associated with sound level(s), hear- ing protection is required.

• To reduce the risk of injury associated

with contacting rotating parts, stop the engine before installing or removing attachments. Do not operate without guard(s) in place.

• Operate power equipment only at rea-

sonable hours-not early in the morn- ing or late at night when people might be disturbed. Comply with times listed

in local ordinances. Usual recommen- dations are 9:00 a.m. to 5:00 p.m., Monday though Saturday.

• To reduce noise levels, limit the num-

ber of pieces of equipment used at any one time.

• To reduce noise levels, operate pow-

er blowers at the lowest possible throttle speed to do the job.

• Use rakes and brooms to loosen

debris before blowing.

• In dusty conditions, slightly dampen

surfaces or use a mister attachment when water is available.

• Conserve water by using power blow-

ers instead of hoses for many lawn and garden applications, including areas such as gutters, screens, patios, grills, porches, and gardens.

• Watch out for children, pets, open

windows, or freshly washed cars. Blow debris away safely.

• Use the full blower nozzle extension

so the air stream can work close to the ground.

START LEVER

The START LEVER helps to supply fuel to the engine to aid in starting. Activate

the starting system by moving the start

lever to the START position. DO NOT squeeze the throttle trigger until the

engine has started and runs. After the

engine starts, allow the engine to warm-up 10-15 seconds, then fully squeeze the throttle trigger to deacti-

vate the starting system (start lever re- turns to RUN position).

• After using blowers and other equip- ment, CLEAN UP! Dispose of debris in trash receptacles.

OPERATING POSITION

Blower Vacuum

BEFORE STARTING ENGINE

_IL WARNING: Be sure to read the fuel information in the safety rules

before you begin. If you do not understand the safety rules, do not

attempt to fuel your unit. Call 1-800-235-5878.

FUELING ENGINE

_WARNING: Remove fuel cap

slowly when refueling.

This engine is certified to operate on un-

leaded gasoline. Before operation, gaso- line must be mixed with a good quality

synthetic 2-cycle air-cooled engine oil.

We recommend Craftsman brand syn- thetic oil. Mix gasoline and oil at a ratio

of 40:1. A 40:1 ratio is obtained by mix- ing 3.2 ounces of oil with 1 gallon of un-

-9-

leaded gasoline. Included with this blow- er is a 312 ounce container of oil. Pour the entire contents of this container into

1 gallon of gasoline to achieve the prop-

er fuel mixture. DO NOT USE automotive oil or boat oil. These oils will cause en-

gine damage. When mixing fuel, follow instructions printed on container. Once

oil is added to gasoline, shake container momentarily to assure that the fuel is

thoroughly mixed. Always read and fol- low the safety rules relating to fuel be-

fore fueling your unit. IMPORTANT

Experience indicates that alcohol

blended fuels (called gasohol or using ethanol or methanol) can attract mois- ture which leads to separation and

formation of acids during storage. Acidic gas can damage the fuel sys-

tem of an engine while in storage. To avoid engine problems, empty the

fuel system before storage for 30 days or longer. Drain the gas tank, start the engine and let it run until the fuel lines

and carburetor are empty. Use fresh fuel next season. Never use engine or

carburetor cleaner products in the fuel tank or permanent damage may occur.

Fuel stabilizer is an acceptable alter-

native in minimizing the formation of fuel gum deposits during storage. Craftsman brand oil is already blended

with fuel stabilizer. See the STORAGE section for additional information.

HOW TO STOP YOUR ENGINE

• Release the throttle trigger.

• Push and hold the STOP switch in the STOP position until the engine stops.

HOW TO START YOUR ENGINE

_WARNING: You MUST make sure the tubes are secure before using the

unit.

• Fuel engine. Move at least 10 feet (3 meters) away from the fueling site.

• Hold the unit in the starting position as shown. Make sure the blower end

is directed away from people, ani- mals, glass, and solid objects.

STARTING POSITION

Blower

_IL WARNING: When starting engine,

hold the unit as illustrated. Do not set unit on any surface except a clean, hard

area when starting engine or while en- gine is running. Debris such as gravel,

sand, dust, grass, etc. could be picked

up by the air intake and thrown out

through the discharge opening, damag-

ing the unit or property, or causing seri- ous injury to bystanders or the operator.

STARTING A COLD ENGINE (or

warm engine after running out of fuel)

1. Move the throttle position lever (cruise control) to the idle position.

Throttle

Position Lever

(Oruise

Control)

2. Slowly press the primer bulb 6 times.

3. Move the start lever to the START position.

-10-

Starter _;_. /"

Handl_

4. This unit has the Sim-pul " starting system. You do not have to pull the

starter rope handle sharply or briskly. Pull starter rope handle 5

times with a controlled and steady

motion (no more than 3 times above 90°F). If engine starts and

runs prior to 5 pulls, allow engine to run for 5 seconds; then, fully

squeeze the throttle trigger to dis- engage the starting system (start lever returns to RUN position).

Steps 5 and 6 are not necessary.

5. Fully squeeze the throttle trigger to disengage the starting system (start

lever returns to RUN position).

6. Pull starter rope handle with a con- trolled and steady motion while squeezing throttle trigger until engine starts and runs.

STARTING A WARM ENGINE

1. Squeeze and hold the throttle trigger.

2. Pull starter rope handle with a con- trolled and steady motion while squeezing throttle trigger until en-

gine starts and runs.

NOTE: Normally, the warm starting procedure can be used within 5-10 minutes after the unit is turned off. If

the unit sits for more than 10 minutes without being used, it will be necessary

to start the unit by following the steps

under STARTING A COLD ENGINE or fol- lowing the starting instruction steps

shown on the unit.

STARTING A FLOODED ENGINE

Flooded engines can be started by mov- ing the start lever to the RUN position

and fully squeezing the throttle trigger. Pull the starter handle repeatedly while

squeezing throttle trigger until engine

starts and runs. This could require pull-

ing the starter handle many times, de-

pending on how badly the unit is flooded. If the unit still doesn't start, re- fer to the TROUBLESHOOTING TABLE or

call 1-800-235-5878.

CUSTOMER RESPONSIBILITIES _, WARNING: Disconnect the spark plug before performing maintenance,

service, or adjustments.

CARE & MAINTENANCE TASK Check for loose fasteners and parts

Check for damaged or worn parts Inspect and clean unit and labels

Clean air filter Replace spark plug

Replace fuel filter Check muffler mounting screws

_WARNING: Avoid touching muf- fler unless engine and muffler are cold.

A hot muffler can cause serious burns. _WARNING: Stop engine and be

sure the impeller blades have stopped turning before opening the vacuum in- let door or attempting to insert or re-

move the vacuum or blower tubes. The rotating blades can cause serious

injury. Always disconnect the spark

WHEN TO PERFORM

Before each use Before each use

After each use Every 5 hours of operation

Yearly Yearly

Yearly

plug before performing maintenance or

accessing movable parts.

GEN ERAL RECOMMEN DATIONS The warranty on this unit does not cov-

er items that have been subjected to

operator abuse or negligence. To re-

ceive full value from the warranty, the

operator must maintain unit as instruct-

ed in this manual. Various adjustments will need to be made periodically to

properly maintain your unit.

-11 -

CHECK FOR LOOSE

FASTENERS AND PARTS

• Muffler

• Spark Plug Boot

• Air Filter

• Housing Screws CHECK FOR DAMAGED OR

WORN PARTS Contact Sears Service Center for re-

placement of damaged or worn parts.

• Throttle Lever - Ensure throttle lever functions properly by moving the

throttle lever to the STOP position. Make sure engine stops; then restart engine and continue.

• Fuel Tank - Do not use unit iffuel tank shows signs of damage or leaks.

• Vacuum Bag - Do not use vacuum bag if it is torn or damaged.

INSPECT AND CLEAN UNIT AND LABELS

• After each use, inspect complete unit for loose or damaged parts. Clean the unit using a damp cloth with a

mild detergent.

• Wipe off unit with a clean dry cloth.

CLEAN AIR FILTER A dirty air filter decreases engine per- formance and increases fuel consump- tion and harmful emissions. Always

clean after every 5 hours of operation.

5. Apply a few drops of oil to the filter; squeeze filter to distribute oil.

6. Replace parts.

REPLACE SPARK PLUG

Replace spark plug each year to ensure

the engine starts easier and runs better.

Set spark plug gap at 0.025 inch. Igni-

tion timing is fixed, nonadjustable.

1. Twist, then pull off spark plug boot.

2. Remove spark plug from cylinder and discard.

3. Replace with Champion RCJ-6Y spark plug and tighten securely with a 3/4 inch socket wrench.

4. Reinstall the spark plug boot.

REPLACE FUEL FILTER

To replace fuel filter, drain unit by run-

ning it dry of fuel, then remove fuel cap/retainer assembly from tank. Pull

filter from tank and remove it from the fuel line. Install new fuel filter on fuel

line; reinstall parts.

Fuel Filter

Fuel Line

Button /_._

Air Filer J'1

Cleaning the air filter:

1. Clean the cover and the area around it to keep debris from falling

into the carburetor chamber when

the cover is removed.

NOTE: Move start lever to RUN posi-

tion before opening air filter cover.

2. Open air filter cover by pushing button (see illustration). Remove

air filter.

NOTE: Do not clean filter in gasoline

or other flammable solvent. Doing so can create a fire hazard or produce

harmful evaporative emissions.

3. Wash the filter in soap and water.

4. Allow filter to dry.

CHECK MUFFLER MOUNTING

SCREWS

Once each year, ensure muffler mounting screws are secure and tight-

ened properly to prevent damage.

Muffler

Mounting Screw

INSPECT MUFFLER AND SPARK

ARRESTING SCREEN

,_ WARNING: The muffler on this

product contains chemicals known to

the State of California to cause cancer. As the unit is used, carbon deposits

build up on the muffler and spark ar-

-12-

+ 28 hidden pages