Craftsman 358791060 Owner’s Manual

Operator's Manual

32cc/1.9 cu.in. 2-Cycle

17 Inch Cutting Path/0.080 Inch Line

GASOLINE WEEDWAOKER ®

Model No.

358.791060

• Safety

• Assembly

• Operation

• Maintenance

• Parts List

• Espar_ol, p. 22

WARNING:

Read and follow all Safety Rules and Operating Instructions before first use of this product.

For answers to your questions about this product:

Call 7 am-7 pm, Mon.-Sat., or 10 am-7 pm, Sun.

1-800-235-5878 _Ho°_slisted are Central Time)

Sears, Roebuck and Co., Hoffman Estates, IL 60179 U.S.A.

545082983 9/12/06

WarrantyStatement 2 Storage 16 IdentificationofSymbols 2 TroubleshootingTable 17

SafetyRules 3 EmissionsStatement 18 Assembly 8 Operation 10 PartsList 20 Maintenance 14 Spanish 22

Service&Adjustments 15 PartsandOrdering BackCover

ONEYEAR FULL WARRANTY ON CRAFTSMAN ® GAS WEEDWACKER ®

When used and maintained according to the operator's manual, ifthis product fails due to a defect in material or workmanship within one year from the date of pur-

chase, return it to any Sears store, Sears Service Center, or other Craftsman outlet in the United States for free repair (or replacement if repair proves impossible).

This warranty excludes cutting line, spark plug and air filter, which are expendable parts that can wear out from normal use in less than one year.

This warranty applies for only 30 days from purchase date if this product is used for commercial or rental purposes.

This warranty gives you specific legal rights, and you may also have other rights which vary from state to state.

Sears, Roebuck and Co., Hoffman Estates, IL 60179

WARNING! This trimmer

can be dangerous! Careless or improper use can cause

serious or even fatal injury.

Always wear appropriate hearing protection, eye protection and head protection,

Read and understand the operator's manual before using the trimmer.

4_WARNING: When using gar- dening appliances, basic safety pre-

cautions must always be followed to reduce the risk of fire and serious

injury. Read and follow all instructions.

This power unit can be dangerous! Op-

erator is responsible for following instructions and warnings on unit and in

manual. Read entire operator's manual before using unit! Be thoroughly familiar

with the controls and the proper use of the unit. Restrict the use of this unit to

persons who have read, understand, and will follow the instructions and

warnings on the unit and in the manual. Never allow children to operate this unit.

OPERATOR'S SAFETY INFORMATION MANUAL ON THE UNIT

dl_ DANGER: Never use blades with line trimmer attachment, Never

use flailing devices with any attach- ment. This unit (when used with sup- plied line trimmer attachment) is de-

signed for line trimmer use only. Use of any other accessories with line trim-

mer attachment will increase the risk of injury.

@OO

_&WARNING: Trimmer line throws objects violently. You and others can be

blinded/injured. Wear eye and leg protection. Keep body parts clear of ro-

tating line.

Eye Protection

/_zardZone

-tl

lm. 8oots

_WARNING: Hazard zone for thrown objects. Trimmer line can

throw objects violently. Others can be blinded or injured. Keep children, by- standers, and animals 50 feet (15 me-

ters) away. Stop unit immediately if ap- proached.

If situations occur which are not cov- ered in this manual, use care and good judgment. If you need assis-

tance, contact your Sears Service Center or call 1-800-235-5878.

OPERATOR SAFETY

• Dress properly. Always wear safety

glasses or similar eye protection when operating, or performing main-

tenance, on your unit (safety glasses are available). Eye protec-

tion should be marked Z87.

• Always wear face or dust mask if op-

eration is dusty.

• Always wear heavy, long pants, long

sleeves, boots, and gloves. Wearing safety leg guards is recommended.

• Always wear foot protection. Do not go barefoot or wear sandals. Stay clear of spinning line.

• Secure hair above shoulder length. Secure or remove loose clothing or

clothing with loosely hanging ties, straps, tassels, etc. They can be

caught in moving parts.

• Being fully covered also helps pro- tect you from debris and pieces of

toxic plants thrown by spinning line.

• Stay Alert. Do not operate this unit when you are tired, ill, upset or un-

der the influence of alcohol, drugs, or medication. Watch what you are

doing; use common sense.

• Wear hearing protection.

• Never start or run inside a closed room or building. Breathing exhaust

fumes can kill.

• Keep handles free of oil and fuel.

• Always keep engine on the right hand side of your body.

• Hold the unit firmly with both hands.

• Keep trimmer head (or other option- al attachment) below waist level and

away from all parts of your body. Do not raise engine above your waist.

• Keep all parts of your body away from muffler and spinning line (or

other optional attachment). A hot muffler can cause serious burns.

• Keep firm footing and balance. Do not overreach or use from unstable

surfaces such as ladders, trees, steep slopes, rooftops, etc.

• Use only in daylight or good artificial light.

• Use only for jobs explained in this manual (or manuals for optional at- tachments).

UNIT / MAINTENANCE SAFETY

_,WARNING: Stop unit and dis- connect the spark plug before per-

forming maintenance (except carbure- tor adjustments).

• Look for and replace damaged or loose parts before each use. Look for and repair fuel leaks before use.

Keep in good working condition.

• Replace trimmer head parts that are chipped, cracked, broken, or dam-

aged in any other way before using the unit.

• Maintain unit according to recom- mended procedures. Keep cutting

line at proper length.

• Use only 0.080 inch (2 mm) diameter Craftsman_R_brand line. Never use

wire, rope, string, etc.

• Install required shield properly before using the unit. Use only specified trim-

mer head; make sure it is properly installed and securely fastened.

• Make sure unit is assembled cor- rectly as shown in this manual.

• Make carburetor adjustments with lower end supported to prevent line

from contacting any object.

• Keep others away when making car- buretor adjustments.

• Use only recommended Craftsman accessories and replacement parts.

• Have all maintenance and service not explained in this manual per- formed by a Sears Service Center.

FUEL SAFETY

• Mix and pour fuel outdoors.

• Keep away from sparks or flames.

• Do not smoke or allow smoking near fuel or the unit or while using the unit.

• Avoid spilling fuel or oil. Wipe up all fuel spills before starting engine.

• Move at least 10 feet (3 meters) away from fueling site before start-

ing engine. Stop engine and allow it to cool before removing fuel cap.

• Empty the fuel tank before storing or transporting the unit. Use up fuel left

in the carburetor by starting the en- gine and letting it run until it stops.

• Store unit and fuel in area where fuel vapors cannot reach sparks or open

flames from water heaters, electric motors or switches, furnaces, etc.

• Always store gasoline in a container approved for flammable liquids.

TRANSPORTING AND STORAGE

• Stop the unit before carrying.

• Allow engine to cool before storing or transporting in vehicle.

• Empty the fuel tank before storing or transporting the unit. Use up fuel left

in the carburetor by starting the en- gine and letting it run until it stops.

• Store unit and fuel in area where fuel vapors cannot reach sparks or

open flames from water heaters, electric motors or switches, furnaces,

etc.

• Store unit so line limiter blade can- not accidentally cause injury. The

unit can be hung by the shaft.

• Store unit out of reach of children.

This unit is not equipped with an anti- vibration system and is intended for

occasional use only. SAFETY NOTICE: Exposure to vibra-

tions through prolonged use of gaso-

line powered hand tools could cause blood vessel or nerve damage in the

fingers, hands, and joints of people

prone to circulation disorders or ab- normal swellings. Prolonged use in

cold weather has been linked to blood vessel damage in otherwise healthy

people. If symptoms occur such as

numbness, pain, loss of strength, change in skin color or texture, or loss of feeling in the fingers, hands, or

joints, discontinue the use of this tool and seek medical attention. An anti-

vibration system does not guarantee the avoidance of these problems. Us-

ers who operate power tools on a con- tinual and regular basis must monitor

closely their physical condition and the condition of this tool.

SPECIAL NOTICE: This unit is equipped with a temperature limiting

muffler and spark arresting screen which meets the requirements of Cali-

fornia Codes 4442 and 4443. All U.S. forest land and the states of California,

Idaho, Maine, Minnesota, New Jersey,

Oregon, and Washington require by

law that many internal combustion en- gines be equipped with a spark arrest-

ing screen. If you operate in a locale where such regulations exist, you are

legally responsible for maintaining the operating condition of these parts.

Failure to do so is a violation of the

law. For normal homeowner use, the

muffler and spark arresting screen will

not require any service. After 50 hours of use, we recommend that your muf- fler be serviced or replaced by a

Sears Service Center.

LINE TRIMMER SAFETY

WARNING: Inspect the area to be trimmed before each use. Remove objects (rocks, broken glass, nails,

wire, etc.) which can be thrown by or become entangled in line. Hard ob-

jects can damage the trimmer head and be thrown causing serious injury.

• Only use the trimmer attachment for

trimming, scalping, mowing and sweeping. Do not use the trimmer

attachment for edging, pruning or hedge trimming.

• Cut only from your left to your right.

Cutting on right side of the shield will throw debris away from the operator.

ADDITIONAL SAFETY RULES

FOR OPTIONAL ATTACHMENTS

_WARNING: For each optional attachment used, read entire opera-

tors manual before use and follow all warnings and instructions in manual

and on attachment.

_WARNING: Ensure handlebar is installed when using edger or brush-

cutter attachments. Attach handlebar above arrow on safety label on the up- per shaft (engine end of unit). If your

edger or brushcutter attachment does not include a handlebar, a handlebar

accessory kit (#530071451 ) is avail- able from your Sears Service Center.

EDGER SAFETY

WARNING: Inspect the area to

be edged before each use. Remove objects (rocks, broken glass, nails, wire, etc.) which can be thrown by the

blade or can wrap around the shaft.

• Blade rotates momentarily after the

trigger is released. The blade can seriously cut you or others.

• Allow blade to stop before removing

it from the cut.

Blade rotates Allowbladetostop

after the fromthe cut. J

release_

td_lgeris _/

• Throw away blades that are bent, warped, cracked, broken or dam-

aged in any other way. Replace parts that are cracked, chipped, or

damaged before using the unit.

• Do not attempt to remove cut materi- al nor hold material to be cut when

the engine is running or when cut- ting blade is moving.

• Always keep the wheel and depth adjusting skid in contact with the

ground.

• Always push the unit slowly over the ground. Stay alert for uneven side-

walks, holes in the terrain, large roots, etc.

• Always use the handlebar when us- ing edger attachment.

BLOWERNACUUM SAFETY

_,WARNING: Inspect area before starting unit. Remove all debris and

hard objects such as rocks, glass,

wire, etc. that can ricochet, be thrown, or otherwise cause injury or damage during operation.

• Do not set unit on any surface ex- cept a clean, hard area while engine

is running. Debris such as gravel, sand, dust, grass, etc., could be picked up by the air intake and

thrown out through discharge open- ing, damaging unit, property, or

causing serious injury to bystanders or operator.

• Never place objects inside the blow- er tubes, vacuum tubes or blower

outlet. Always direct the blowing de- bris away from people, animals,

glass, and solid objects such as trees, automobiles, walls, etc. The

force of air can cause rocks, dirt, or sticks to be thrown or to ricochet

which can hurt people or animals, break glass, or cause other damage.

• Never run unit without the proper equipment attached. When using your unit as a blower, always install blower tubes.

beforeremovingit #

• Checkairintakeopening,blower tubesorvacuumtubesfrequently,

alwayswithenginestoppedand sparkplugdisconnected.Keep

ventsanddischargetubesfreeof

debriswhichcanaccumulateand restrictproperairflow.

• Neverplaceanyobjectinairintake openingasthiscouldrestrictproper

airflowandcausedamagetothe

unit.

• Neveruseforspreadingchemicals, fertilizers,orothersubstanceswhich

maycontaintoxicmaterials.

• Toavoidspreadingfire,donotuse nearleaforbrushfires,fireplaces,

barbecuepits,ashtrays,etc.

BRUSHCUTTER SAFETY

DANGER: Blade can thrust vio-

lently away from material it does not cut. Blade thrust can cause amputa-

tion of arms or legs.

4t_WARNING: Do not use trimmer head as a fastening device for the

blade.

etc.) which can be thrown or become entangled in the blade or trimmer line.

• Throw away and replace blades that are bent, warped, cracked, broken

or damaged in any other way.

• Install required shield properly be- fore using the unit. Use the metal

shield for all metal blade use.

_,WARNING: Only use brushcut- ter attachments that provide a metal

shield with protruding nose.

Protrudin g

• Use only specified blade and make sure it is properly installed and se- curely fastened.

• Cut from your left to your right.

• Always use the handlebar and a properly adjusted shoulder strap

with blade (see ASSEMBLY instruc- tions in brushcutter attachment

operator's manual).

CULTIVATOR SAFETY _WARNING: Rotating tines can

cause serious injury. Keep away from

rotating tines. Stop the engine and disconnect the spark plug before un- clogging tines or making repairs.

• The blade continues to spin after the throttle is released or engine is turned

off. The coasting blade can throw ob- jects or seriously cut you if accidental-

ly touched. Stop the blade by contact- ing the right hand side of the coasting

blade with material already cut.

S_a°cPC_yStio_rgact ,

with cut mat_ L

41WARNING: Inspect the area to be cut before each use. Remove ob-

jects (rocks, broken glass, nails, wire,

dMI=WARNING: Inspect the area to

be cultivated before starting the unit. Remove all debris and hard and sharp

objects such as rocks, vines, branch- es, rope, string, etc.

• Avoid heavy contact with solid objects that might stop the tines. If heavy con-

tact occurs, stop the engine and in- spect the unit for damage.

• Never operate the cultivator without the tine cover in place and properly secured.

• Keep the tines and guard clear of debris.

• After striking a foreign object, stop the engine, disconnect the spark

plug and inspect the cultivator for damage. Repair before restarting.

• Disconnectattachmentfromthedrive enginebeforecleaningthetineswith

ahoseandwatertoremoveany build-up.Oilthetinestopreventrust.

• Alwaysweargloveswhenservicingor cleaningthetines.Thetinesbecome

verysharpfromuse.

• Donotrununitathighspeedunless cultivating.

HEDGE TRIMMER SAFETY

DANGER: RiSK OF CUT; KEEP

HANDS AWAY FROMBLADE - Blade moves momentarily after the trigger is

released. Do not attempt to clear away cut material when the blade is in mo-

tion. Make sure the switch is in the OFF position, the spark plug wire is discon- nected, and the blade has stopped

moving before removing jammed mate- rial from the cutting blade. Do not grab

or hold the unit by the cutting blade.

Blades move

momentarily

after the

triggeris

eased.

Allow blades to stop before removing

them from the cut.

,_WARNING: A coasting blade/ro-

tating chain can cause injury while it continues to move after the engine is

stopped. Maintain proper control of the

unit until the blade/chain has completely

stopped moving. Keep hands, face and feet at a distance from all moving parts.

Do not attempt to touch or stop the blade or chain when it is moving.

_bWARNING: Falling objects can cause severe head injury. Wear head

protection when operating this unit

with a pole pruner attachment.

,_WARNING:

fore starting the unit. Remove all de- bris and hard objects such as rocks, glass, wire, etc. that can ricochet, be

thrown, or otherwise cause injury or damage during operation.

• Do not use a cutting blade that is bent, warped, cracked, broken or

damaged in any other way. Have worn or damaged parts replaced by

your Sears Service Center.

• Always keep unit in front of your body. Keep all parts of your body

away from the cutting blade.

• Keep the cutting blade and air vents clear of debris.

POLE PRUNER SAFETY

_,WARNING: The reciprocating blade/rotating chain can cause severe

injury. Inspect the unit before use. Do not operate unit with a bent, cracked

or dull blade or dull chain. Keep away from the blade/chain.

WARNING: The reciprocating

blade/rotating chain is sharp. Do not touch. To prevent serious injury, always stop engine and ensure blade/chain

has stopped moving, disconnect spark plug, and wear gloves when changing or handling the blade or chain.

Inspect the area be-

A _______

4_WARNING: To prevent serious

injury, do not use more than one boom

extension with a pole pruner attach-

ment.

&WARNING: Keep the pruner away from power lines or electrical

wires.

• Only use for pruning limbs or branches up to 4 inches (10 cm) in

diameter.

• Do not operate the unit faster than the speed needed to prune. Do not

run the unit at high speed when not pruning.

• Always stop the unit when work is delayed or when walking from one cutting location to another.

• If you strike or become entangled with a foreign object, stop the engine immediately and check for damage.

Have any damage repaired by a Sears Service Center before at-

tempting further operations. Discard blades that are bent, warped,

cracked or broken.

• Stop the unit immediately if you feel excessive vibration. Vibration is a

sign of trouble. Inspect thoroughly for loose nuts, bolts or damage

beforecontinuing.ContactSears Serviceforrepairorreplacementof

affectedpartsasnecessary.

SNOW THROWER SAFETY

,_WARNING: Keep hands and feet away from the rotor when starting or running the engine. Never attempt

to clear the rotor with the engine/motor running. Stop engine and disconnect spark plug before unclogging snow or

debris from discharge chute or when adjusting vanes.

miWARNING: Never lean over dis- charge chute. Rocks or debris could

be thrown into the eyes and face and cause serious injury or blindness.

_,WARNING: Inspect the area where the unit is to be used. Remove

objects that could be thrown or dam- age the unit. Some objects may be

hidden by fallen snow -- be alert for the possibility.

• Direct material discharge away from glass enclosures, automobiles, etc.

• Do not run engine at high speed while not removing snow.

• Be attentive when using the snow- thrower, and stay alert for holes in

the terrain and other hidden haz- ards.

• Make sure the rotor will spin freely before attaching the snowthrower to

the powerhead.

• If the rotor will not rotate freely due to frozen ice, thaw the unit thorough- ly before attempting to operate

under power.

• Keep the rotor clear of debris.

• Do not throw snow near other people. The snow thrower could

propel small objects at high speed causing injury.

• After striking a foreign object, stop the engine, disconnect spark plug

and inspect the snowthrower for damage and repair if necessary be-

fore restarting unit.

• Never operate the snowthrower near glass enclosures, automobiles and

trucks.

• Never attempt to use the snow- thrower on a roof.

• Never operate the snowthrower near window wells, dropoffs, etc.

• Never discharge snow onto public roads or near moving traffic.

• Clear snow from slopes by going up and down; never across. Use cau-

tion when changing directions. Nev- er clear snow from steep slopes.

• Let snowthrower run for a few min- utes after clearing snow so moving

parts do not freeze.

• Look behind and use care when backing up. Exercise caution to

avoid slipping or falling, especially when operating in reverse.

• Know how to stop quickly.

CARTON CONTENTS Check carton contents against the fol-

lowing list. Model 358,791060

• Powerhead

• Trimmer attachment

• Shield

• Wing Nut (screwed onto shield)

• Container of oil Examine parts for damage. Do not

use damaged parts.

NOTE: If you need assistance or find

parts missing or damaged, call

1-800-235-5878. It is normal for the fuel filter to rattle in

the empty fuel tank.

Finding fuel or oil residue on muffler is normal due to carburetor adjustments

and testing done by the manufacturer. ASSEMBLY

_,WARNING: Always stop unit and disconnect spark plug before per-

forming any assembly procedures. _bWARNING: If received as-

sembled, repeat all steps to ensure your unit is properly assembled and all

fasteners are secure.

INSTALLING TRIMMER ATTACH- MENT

CAUTION: When installing trimmer attachment, place the unit on a flat

surface for stability.

1. Loosen the coupler by turning the

knob counterclockwise.

Coupler

Shipph_g protector

TIGHTEN

Knob

2. Remove shipping protector from

coupler.

3. Remove the shaft cap from the

trimmer attachment (if present).

4. Position locking/release button of

attachment into guide recess of coupler.

5. Push the attachment into the cou-

pler until the locking/release button snaps into the primary hole.

6. Before using the unit, tighten the

knob securely by turning clock-

wise.

Coupler Primary Hole

Guide Recess

Upper Locking/ Attachment

Release

Shaft

Button

mlWARNING: Make sure the lock- ing/release button is locked in the pri-

mary hole and the knob is securely tightened before operating the unit. All

attachments are designed to be used in the primary hole unless otherwise

stated in the applicable attachment op- erator's manual. Using the wrong hole could lead to serious injury or damage

to the unit,

ATTACHING SHIELD

,_kWARNING: The shield must be

properly installed. The shield provides partial protection from the risk of thrown

objects to the operator and others and

is equipped with a line limiter blade

which cuts excess line to the proper

length. The line limiter blade (on under-

side of shield) is sharp and can cut you.

For proper orientation of shield, see KNOW YOUR TRIMMER illustration in OP- ERATION section.

1, Remove wing nut from shield.

2. Insert bracket into slot as shown.

3. Pivot shield until bolt passes through hole in bracket.

4. Securely tighten wing nut onto bolt.

PIVOT

Shield Slot

Bracket

Line Umiter

Blade

Wing

Nut

ADJUSTING THE HANDLE

,40&WARNING: When adjusting tile assist handle, be sure it remains above the safety label and below the mark or

arrow on the shaft.

1, Loosen wing nut on handle.

2. Rotate the handle on the shaft to an upright position; retighten wing nut,

Secoedary Hote

Locking/Release Button in Primary Hole

For optional attachments, see the AS- SEMBLY section of the applicable at- tachment operator's manual.

KNOWYOUR TRIMMER

READ THiS OPERATOR'S MANUAL AND SAFETY RULES BEFORE OPERATING YOUR UNIT. Compare the illustrations with your unit to familiarize yourself with the location of

the various controls and adjustments. Save this manual for future reference.

Assist Handle

Coupler

Shield

Throttle Trigger

Start Lever

Trimmer

Head

Line Limiter Blade

Shaft

ON/OFF SWITCH The ON/OFF switch is located on the

trigger handle and is used to stop the engine. Move the switch to the OFF

position to stop the engine.

PRIMER BULB The PRIMER BULB removes air from

the carburetor and fuel lines and fills them with fuel. This allows you to start the engine with fewer pulls on the

starter rope. Activate the primer bulb by pressing it and allowing it to return

to its original form.

BEFORE STARTING ENGINE

_WARNING: Be sure to read the fuel information in the safety rules

before you begin. If you do not under- stand the safety rules, do not attempt

to fuel your unit. Call 1-800-235-5878.

FUELING ENGINE ,_WARNING: Remove fuel cap

slowly when refueling. This engine is certified to operate on

unleaded gasoline. Before operation, gasoline must be mixed with a good

quality synthetic 2-cycle air-cooled en- gine oil. We recommend Craftsman

brand synthetic oil. Mix gasoline and oil at a ratio of 40:1. A 40:1 ratio is ob-

tained by mixing 3.2 ounces of oil with 1

ON/OFF Switch

Starter Handle

Primer Bulb

Muffler

START LEVER

The START LEVER helps to supply fuel to the engine to aid in starting. Acti- vate the starting system by moving the

start lever to the START position. DO

NOT squeeze the throttle trigger until

the engine has started and runs. After the engine starts, allow the engine to

warm-up 5 seconds, then fully squeeze the throttle trigger to deacti-

vate the starting system (start lever

returns to RUN position).

COUPLER

The COUPLER enables optional at- tachments to be installed on the unit.

gallon of unleaded gasoline. Included with this trimmer is a 3.2 ounce contain-

er of oil. Pour the entire contents of this container into 1 gallon of gasoline to

achieve the proper fuel mixture. DO

NOT USE automotive oil or marine oil. These oils will cause engine damage. When mixing fuel, follow instructions

printed on container.

Once oil is added to gasoline, shake container momentarily to assure that the fuel is thoroughly mixed. Always

read and follow the safety rules relat-

ing to fuel before fueling your unit.

IMPORTANT

Alcohol blended fuels (called gasohol or using ethanol or methanol) can at-

tract moisture which leads to separa- tion and formation of acids during star-

age.Acidicgascandamagethefuel systemofanenginewhileinstorage. Toavoidengineproblems,emptythe

fuelsystembeforestoragefor30days orlonger.Drainthegastank,startthe

engineandletitrununtilthefuellines andcarburetorareempty.Usefresh

fuelnextseason.

Neveruseengineorcarburetorclean- erproductsinthefueltankorperma- nentdamagemayoccur. SeetheSTORAGEsectionforaddition-

alinformation.

HOWTO STOP YOUR UNIT

• Release the throttle trigger.

• Move the ON/OFF switch to the OFF

position.

ON/OFF Switch

HOW TO START YOUR UNIT _WARNING: Avoid any contact

with the muffler, A hot muffler can cause serious burns.

_ '_"St arting Position

STARTING A COLD ENGINE

NOTE: DO NOT squeeze tile throttle

trigger until the engine has started and runs.

1. Set unit on a flat surface.

2. Move ON/OFF switch to the ON

position.

3. Slowly press the primer bulb 6

times.

4. Move the start lever to the START

position.

_,/Starter Handle

Start

Primer Bulb

Muffler

5. This unit has the Sim-pul" starting system. You do not have to pull the

starter rope handle sharply or brisk- ly. Pull starter rope handle with a

controlled and steady motion until engine starts and runs.

6. Allow unit to run for 5 seconds, then fully squeeze the throttle trigger to

disengage the starting system (start lever returns to RUN position).

STARTING A WARM ENGINE

1. Move ON/OFF switch to the ON position.

2. Squeeze and hold the throttle trig- ger. Keep throttle trigger fully

squeezed until engine runs smoothly.

3. Pull starter rope handle with a con- trolled and steady motion while

squeezing throttle trigger until en- gine starts and runs.

NOTE: Normally, the warm starting procedure can be used within 5-10

minutes after the unit is turned off. If

the unit sits for more than 10 minutes without being used, it will be neces-

sary to start the unit by following the steps under STARTING A COLD EN-

GINE or following the starting instruc- tion steps shown on the unit.

STARTING A FLOODED ENGINE

Flooded engines can be started by placing the ON/OFF switch in the ON

position. Move the start lever to the RUN position and fully squeeze throttle

trigger. Pull the starter rope handle re-

peatedly while squeezing throttle trig-

ger until engine starts and runs. This could require pulling the starter rope

handle many times, depending on how badly the unit is flooded.

If the unit still doesn't start, refer to

TROUBLESHOOTING TABLE or call

1-800-235-5878.

CRAFTSMAN ®

CONVERTIBLE TM FEATURE

This model is equipped with a coupler which enables optional attachments to

be installed. The optional attachments

are:

Edger ................. 358.79240

Cultivator .............. 358.79241

Blower ................ 358.79242

Brushcutter ............ 358.79244

Pruner ................ 358.79245

&WARNING: Always stop unit and disconnect spark plug before re-

moving or installing attachments.

REMOVING TRIMMER ATTACH-

MENT (OR OTHER OPTIONAL AT- TACHMENTS)

CAUTION: When removing or instal-

ling attachments, place the unit on a flat surface for stability.

1. Loosen the coupler by turning the knob counterclockwise.

Upper Shaft

Coupler

.OOSEN

Attachment

TIGHTEN Knob

2. Press and hold the locking/release button.

Locking/Release Button

CouF Upper Shaft

Attachment

3. While securely holding the engine and upper shaft, pull the attach- ment straight out of the coupler.

INSTALLING OPTIONAL ATTACH-

MENTS

1. Remove the shaft cap from tile at- tachment (if present).

2. Position locking/release button of attachment into guide recess of

coupler.

3. Push the attachment into the cou- pler until the locking/release button snaps into the primary hole.

4. Before using the unit, tighten the knob securely by turning clock-

wise.

Coupler Primary Hole

Upper Locking/ Attachment

Shaft Release

Guide Recess

Button

_WARNING: Make sure the lock- ing/release button is locked in the pri-

mary hole and the knob is securely tightened before operating the unit. All

attachments are designed to be used in the primary hole unless otherwise stated in the applicable attachment op-

erator's manual. Using the wrong hole could lead to serious injury or damage

to the unit.

Secondary Hole

Locking/Release Button in Primary Hole

OPERATING INSTRUCTIONS To maximize operating efficiency, do

not run the engine for longer than 1 minute at a time at full throttle.

OPERATING POSITION

ALWAYS USE: Hearing

Protection Eye Protection

Long Pants

Shoes

Heavy ,,_

Cut from your right to your left.

_'WARNING: Always wear eye

protection and hearing protection. Never lean over the trimmer head. Rocks or

debris can ricochet or be thrown into eyes and face and cause blindness or

other serious injury. When operating unit, stand as shown

and check for the following:

• Wear eye protection, hearing protec- tion and heavy clothing.

• Hold trigger handle with right hand and assist handle with left hand.

• Hold unit so that engine is below waist level.

• Cut only from your right to your left to ensure debris is thrown away from

you. Without bending over, keep line near and parallel to the ground and

not crowded into material being cut.

Do not run the engine at a higher speed

than necessary. The cutting line will cut efficiently when the engine is run at less

than full throttle. At lower speeds, there

is less engine noise and vibration.

+ 27 hidden pages