![](/html/30/3015/3015d12b6a705366770375a87b200d7de8749bbb0227504251b5ad1eee335445/bg1.png)
Operator's Manual
ICRAFTSMAN°I
2.4 cu.in./40cc 2-Cycle
GASOLINE CHAIN SAW
Model No.
358,350811 - 18 in, Bar
• Safety
• Assembly
• Operation
• Maintenance
• Parts List
• Espar_ol, p. 25
WARNING:
Read and follow all Safety Rules and Operating
Instructions before first use of this product.
For answers to your questions about this product:
Call 7 am-7 pm, Mon-Sat; Sun, 10 am-7 pm
1-800-235-5878 (Hours listed are Central Time)
Sears, Roebuck and Co., Hoffman Estates, IL 60179 U.S.A.
545133482 11/30/06
![](/html/30/3015/3015d12b6a705366770375a87b200d7de8749bbb0227504251b5ad1eee335445/bg2.png)
Warranty 2 Storage 18
SafetyRules 2 TroubleshootingTable 19
Assembly 6 EmissionsStatement 21
Operation 7 PartsList 23
Maintenance 14 Spanish 25
ServiceandAdjustments 17 Parts&Ordering BackCover
ONEYEARFULLWARRANTYONCRAFTSMAN CHAINSAW
Whenusedandmaintainedaccordingtotheoperator'smanual,ifthisproductfails
duetoadefectinmaterialorworkmanshipwithinoneyearfromthedateofpur-
chase,returnittoanySearsstore,SearsServiceCenter,orotherCraftsmanoutletin
theUnitedStatesforfreerepair(orreplacementifrepairprovesimpossible).
Thiswarrantyexcludesthebar,chain,sparkplugandairfilter,whichareexpend-
ablepartsthatcanwearoutfromnormaluseinlessthanoneyear.
Thiswarrantyappliesforonly30daysfrompurchasedateifthisproductisused
forcommercialorrentalpurposes.
Thiswarrantygivesyouspecificlegalrights,andyoumayalsohaveotherrights
whichvaryfromstatetostate.
Sears,RoebuckandCo.,HoffmanEstates,IL60179
A
&IWARNING: Always disconnect
spark plug wire when making repairs ex-
cept for carburetor adjustments. Be-
cause a chain saw is a high-speed
wood-cutting tool, special precautions
must be observed to reduce the risk of
accidents. Careless or improper use of
this tool can cause serious injury.
PLAN AHEAD
• Restrict the use of your saw to adult
users who understand and can fol-
low safety rules, precautions, and
operating instructions found in this
manual.
Hearing / Safety Hat
Protection ._,_ j
_. _._ Eye
Snug
Fitting Heavy Duty
Clothing Gloves
"_ IIqPlPII- Protection
Safety Safety Chaps
Shoes
• Wear protective gear. Always use
steel-toed safety footwear with non-slip
soles; snug-fitting clothing; heavy-duty,
non-slip gloves; eye protection such
as non-fogging, vented goggles or
face screen; an approved safety hard
hat; and sound barriers (ear plugs or
mufflers) to protect your hearing. Reg-
ular users should have hearing
checked regularly as chain saw noise
can damage hearing.
• Secure hair above shoulder length. Do
not wear loose clothing or jewelry; they
can get caught in moving parts.
• Keep all parts of your body away from
the chain when the engine is running.
• Keep children, bystanders, and ani-
mals a minimum of 30 feet (10 me-
ters) away from the work area when
starting and using the saw.
• Do not handle or operate a chain
saw when you are fatigued, ill, or up-
set, or if you have taken alcohol,
drugs, or medication. You must be in
good physical condition and mentally
alert. If you have any condition that
might be aggravated by strenuous
work, check with doctor before oper-
ating.
• Do not start cutting until you have a
clear work area, secure footing, and,
if you are felling trees, a planned re-
treat path.
2
![](/html/30/3015/3015d12b6a705366770375a87b200d7de8749bbb0227504251b5ad1eee335445/bg3.png)
OPERATE YOUR SAW SAFELY
• Do not operate a chain saw with one
hand. Serious injury to the operator,
helpers, bystanders or any combina-
tion of these persons may result from
one-handed operation. A chain saw
is intended for two-handed use.
• Operate the chain saw only in a well-
ventilated outdoor area.
• Do not operate saw from a ladder or
in a tree.
• Make sure the chain will not make
contact with any object while starting
the engine. Never try to start the saw
when the guide bar is in a cut.
• Do not put pressure on the saw at
the end of the cut. Applying pressure
can cause you to lose control when
the cut is completed.
• Stop engine before setting saw down.
• Hand carry saw only when engine is
stopped. Carry with muffler away
from body; guide bar & chain project-
ing behind you; guide bar preferably
covered with a scabbard.
• Do not operate a chain saw that is
damaged, improperly adjusted, or
not completely and securely as-
sembled. Always replace bar, chain,
hand guard, or chain brake immedi-
ately if it becomes damaged, broken
or is otherwise removed.
MAINTAIN YOUR SAW IN GOOD
WORKING ORDER
_WARNING: Disconnect the
spark plug before performing mainte-
nance except carburetor adjustments.
• Have all chain saw service performed
by a qualified service dealer with the
exception of the items listed in the
MAINTENANCE section of this manual.
• Make certain the saw chain stops
moving when the throttle trigger is
released. For correction, refer to
CARBURETOR ADJUSTMENT.
• Keep the handles dry, clean, and
free from oil or fuel mixture.
• Keep caps and fasteners securely
tightened.
• Nonconforming replacement compo-
nents or the removal of safety devices
may cause damage to the unit and
possible injury to the operator or by-
standers. Use only Craftsman acces-
sories and replacement parts as rec-
ommended. Never modify your saw.
• Maintain chain saw with care.
• Keep unit sharp and clean for better
and safer performance.
• Follow instructions for lubricating and
changing accessories.
• Check for damaged parts. Before fur-
ther use of the chain saw, a guard or
other part that is damaged should be
carefully checked to determine that it
will operate properly and perform its
intended function. Check for alignment
of moving parts, binding of moving
parts, breakage of parts, mounting and
any other conditions that may affect its
operation. A guard or other part that is
damaged should be properly repaired
or replaced by a Sears Service Center
unless otherwise indicated elsewhere
in the operator's manual.
• When not in use, chain saws should
be stored in a dry, high or locked-up
place out of the reach of children.
• When storing saw, use a scabbard or
carrying case.
HANDLE FUEL WITH CAUTION
• Do not smoke while handling fuel or
while operating the saw.
• Eliminate all sources of sparks or
flame in the areas where fuel is
mixed or poured.
• Mix and pour fuel in an outdoor area
and use an approved, marked con-
tainer for all fuel purposes. Wipe up
all fuel spills before starting saw.
• Move at least 10 feet (3 meters) from
fueling site before starting engine.
• Turn the engine off and let saw cool
in a non-combustible area, not on
dry leaves, straw, paper, etc. Slowly
remove fuel cap and refuel unit.
• Empty the fuel tank before storing or
transporting the unit. Use up fuel left in
the carburetor by starting the engine
and letting it run until it stops.
• Store the unit and fuel in an area
where fuel vapors cannot reach
sparks or open flames from water
heaters, electric motors or switches,
furnaces, etc.
GUARD AGAINST KICKBACK
Follow all safety rules to help avoid
kickback and other forces which can
result in serious injury.
X<._'_ _: Kickback Path
![](/html/30/3015/3015d12b6a705366770375a87b200d7de8749bbb0227504251b5ad1eee335445/bg4.png)
_WARNING:Avoidkickback
whichcanresultinseriousinjury.
Kickbackisthebackward,upwardor
suddenforwardmotionoftheguide
baroccurringwhenthesawchainnear
theuppertipoftheguidebarcontacts
anyobjectsuchasalogorbranch,or
whenthewoodclosesinandpinches
thesawchaininthecut.Contactinga
foreignobjectinthewoodcanalsore-
sultinlossofchainsawcontrol.
• RotationalKickbackcanoccur
whenthemovingchaincontactsan
objectattheuppertipoftheguide
bar.Thiscontactcancausethe
chaintodigintotheobject,which
stopsthechainforaninstant.The
resultisalightningfast,reverse
reactionwhichkickstheguidebarup
andbacktowardtheoperator.
• Pinch-Kickbackcanoccurwhenthe
thewoodclosesinandpinchesthe
movingsawchaininthecutalong
thetopoftheguidebarandthesaw
chainissuddenlystopped.Thissud-
denstoppingofthechainresultsina
reversalofthechainforceusedto
cutwoodandcausesthesawto
moveintheoppositedirectionofthe
chainrotation.Thesawisdriven
straightbacktowardtheoperator.
• Pull4ncanoccurwhenthemoving
chaincontactsaforeignobjectinthe
woodinthecutalongthebottomof
theguidebarandthesawchainis
suddenlystopped.Thissuddenstop-
pingpullsthesawforwardandaway
fromtheoperatorandcouldeasily
causetheoperatortolosecontrolof
thesaw.
REDUCETHECHANCEOF
KICKBACK
• Recognizethatkickbackcanhap-
pen.Withabasicunderstandingof
kickback,youcanreducetheele-
mentofsurprisewhichcontributesto
accidents.
• Neverletthemovingchaincontact
anyobjectatthetipoftheguidebar.
• Keeptheworkingareafreefromob-
structionssuchasothertrees,
branches,rocks,fences,stumps,
etc.Eliminateoravoidany
obstructionthatyoursawchaincould
hitwhileyouarecutting.
• Whencuttingabranch,donotletthe
guidebarcontactbranchorotherob-
jectsaroundit.
• Keepsawchainsharpandproperly
tensioned.Alooseordullchaincan
increasethechanceofkickback.Fol-
lowmanufacturer'schainsharpening
andmaintenanceinstructions.Check
tensionatregularintervals,butnever
withtheenginerunning.Makesure
thebarnutsaresecurelytightened.
• Beginandcontinuecuttingatfull
speed.Ifthechainismovingata
slowerspeed,thereisgreater
chanceofkickbackoccurring.
• Useextremecautionwhenre-enter-
ingapreviouscut.
• Donotattemptcutsstartingwiththe
tipofthebar(plungecuts).
•Watchforshiftinglogsorotherforces
thatcouldcloseacutandpinchor
fallintochain.
• UsetheReduced-KickbackGuide
BarandLow-KickbackChainspeci-
fiedforyoursaw.
Avoid Pinch-Kickback:
• Be extremely aware of situations or
obstructions that can cause material
to pinch the top of or otherwise stop
the chain.
• Do not cut more than one log at a
time.
• Do not twist the saw as the bar is
withdrawn from an undercut when
bucking.
Avoid Pull-In:
• Always begin cutting with the engine
at full speed and the saw housing
against wood.
• Use wedges made of plastic or wood.
Never use metal to hold the cut open.
MAINTAIN CONTROL
Stand to the _eftof the saw
underside ,_
Thumb on \[
Elbow
locked
Never reverse hand positions
• A good, firm grip on the saw with both
hands will help you maintain control.
Don't let go. Grip the rear handle with
your right hand whether you are right
or left handed. Wrap the fingers of
your left hand over and around the
front handlebar, and your left thumb
under the front handlebar. Keep your
left arm straight with the elbow locked.
![](/html/30/3015/3015d12b6a705366770375a87b200d7de8749bbb0227504251b5ad1eee335445/bg5.png)
• Positionyourlefthandonthefront
handlebarsoitisinastraightline
withyourrighthandontherear
handlewhenmakingbuckingcuts.
Neverreverserightandlefthand
positionsforanytypeofcutting.
• Standwithyourweightevenlybal-
ancedonbothfeet.
• Donotoverreach.Youcouldbe
drawnorthrownoffbalanceandlose
controlofthesaw.
• Donotcutaboveshoulderheight.It
isdifficulttomaintaincontrolofsaw
aboveshoulderheight.
KICKBACKSAFETY FEATURES
_, WARNING: Tile following fea-
tures are included on your saw to help
reduce the hazard of kickback; however,
such features will not totally eliminate
this danger. Do not rely only on safety
devices. Follow all safety rules to help
avoid kickback and other forces which
can result in serious injury.
• Front Hand Guard, designed to reduce
the chance of your left hand contact-
ing the chain if your hand slips off the
front handlebar.
• Position of front and rear handlebars,
designed with distance between han-
dles and "in-line" with each other. The
spread and "in-line" position of the
hands provided by this design work
together to give balance and resis-
tance in controlling the pivot of the
saw back toward the operator if kick-
back occurs.
• Reduced-Kickback Guide Bar, de-
signed with a small radius tip which
reduces the size of the kickback
danger zone on the bar tip. This type
of bar has been demonstrated to sig-
nificantly reduce the number and se-
riousness of kickbacks when tested
in accordance with ANSI B175.1.
Tip Guide Bar
_.f,, Small Radius
Large Radius [_ "_
Tip Guide Bar
• Low-Kickback Chain, has met kick-
back performance requirements
when tested on a representative
sample of chain saws below 3.8 cu-
bic inch displacement specified in
ANS! B175.1.
Low-Kickback Chain
_.,,_ longated Guard Link
CHAIN BRAKE
• Chain Brake, designed to stop tile
chain in the event of kickback.
,_&WARNING: WE DO NOT REP-
RESENT AND YOU SHOULD NOT AS-
SUME THAT THE CHAIN BRAKE WILL
PROTECT YOU IN THE EVENT OF A KICK-
BACK. Kickback is a lightning fast action
which throws the bar and rotating chain
back and up toward the operator. Kick-
back can be caused by allowing contact
of the bar tip in the danger zone with
any hard object. Kickback can also be
caused by pinching the saw chain along
the top of the guide bar. This action may
push the guide bar rapidly back toward
the operator. Either of these events may
cause you to lose control of the saw
which could result in serious injury or
even death. DO NOT RELY UPON ANY OF
THE DEVICES BUILT INTOYOUR SAW.
YOU SHOULD USE THE SAW PROPERLY
AND CAREFULLY TOAVOID KICKBACK.
Reduced-kickback guide bars and low-
kickback saw chains reduce tile chance
and magnitude of kickback and are rec-
ommended. Your saw has a low kick-
back chain and bar as original equip-
ment. Repairs on a chain brake should
be made by an authorized Sears Ser-
vice Center. Take your unit to the place
of purchase if purchased from a servic-
ing dealer, or to your nearest Sears Ser-
vice Center
• Tip contact in some cases may cause
a lightning fast reverse REACTION,
kicking guide bar up and back toward
operator.
• Pinching the saw chain along the top
of the guide bar may push the guide
bar rapidly back toward the operator.
• Either of these reactions may cause
you to lose control of the saw which
could result in serious injury. Do not
rely exclusively upon devices built into
your saw.
Contoured Depth Gauge
deflects kickback
force And allows
wood to gradually
ride into Cutter
![](/html/30/3015/3015d12b6a705366770375a87b200d7de8749bbb0227504251b5ad1eee335445/bg6.png)
Thisunitisnotequippedwithananti-
vibrationsystemandisintendedfor
occasionaluseonly.
SAFETYNOTICE:Exposuretovibra-
tionsthroughprolongeduseofgasoline
poweredhandtoolscouldcauseblood
vesselornervedamageinthefingers,
hands,andjointsofpeopleproneto
circulationdisordersorabnormalswell-
ings.Prolongeduseincoldweatherhas
beenlinkedtobloodvesseldamagein
otherwisehealthypeople.Ifsymptoms
occursuchasnumbness,pain,lossof
strength,changeinskincolorortexture,
orlossoffeelinginthefingers,hands,or
joints,discontinuetheuseofthistool
andseekmedicalattention.Ananti-vi-
brationsystemdoesnotguaranteethe
avoidanceoftheseproblems.Users
whooperatepowertoolsonacontinual
andregularbasismustmonitorclosely
theirphysicalconditionandthecondition
ofthistool.
CHAINBRAKE:Ifthissawistobe
usedforcommerciallogging,achain
brakeisrequiredandshallnotbere-
movedorotherwisedisabledtocom-
plywithFederalOSHARegulationsfor
CommercialLogging.
SPARKARRESTINGSCREEN:Your
sawisequippedwithatemperature
limitingmufflerandsparkarresting
screenwhichmeetstherequirements
ofCaliforniaCodes4442and4443.
AllU.S.forestlandandthestatesof
California,Idaho,Maine,Minnesota,
NewJersey,Oregon,andWashington
requirebylawthatmanyinternalcom-
bustionenginestobeequippedwitha
sparkarrestingscreen.Ifyouoperate
achainsawinastateorlocalewhere
suchregulationsexist,youarelegally
responsibleformaintainingtheoperat-
ingconditionoftheseparts.Failureto
dosoisaviolationofthelaw.Referto
theCustomerResponsibilitieschartin
theMAINTENANCEsection.
STANDARDS:Thischainsawislisted
byUnderwritersLaboratories,Inc.inac-
cordancewithAmericanNationalStan-
dardsforGasoline-PoweredChain
SawsSafetyRequirements(ANSI
B175.1-2000).
,t%
all.WARNING: Before using chain
saw, ensure all fasteners are secure.
CARTON CONTENTS
Check carton contents against the fol-
lowing list.
Model 358.350811
• Chain saw (fully assembled)
• Chain adjustment tool (bar tool)
• 2-cycle engine oil
• Carrying case
Examine parts for damage. Do not use
damaged parts.
If you need assistance or find that parts
are missing or damaged, please call
1-800-235-5878.
NOTE: It is normal to hear the fuel filter
rattle in an empty fuel tank.
Your unit has been factory tested and
the carburetor precisely adjusted. As a
result you may smell gasoline or find a
drop of oil/fuel residue on the muffler
when you unpack the unit.
ASSEMBLY
Your saw is fully assembled; no
assembly is necessary.
![](/html/30/3015/3015d12b6a705366770375a87b200d7de8749bbb0227504251b5ad1eee335445/bg7.png)
KNOWYOURCHAINSAW
READ THIS OPERATOR'S MANUAL AND SAFETY RULES BEFORE OPERATING YOUR
CHAIN SAW. Compare the illustrations with your unit to familiarize yourself with the
location of the various controls and adjustments. Save this manual for future ref-
erence.
Chain Front Hand Guard Front Handle
Adjustment Tool
(Bar Tool) "_ Starter Rope
ON/STOP
Switch Choke/
Chain Muffler Lever
Bar Bar Oil Fill Cap
Sprocket
Hole
Starter Housing
Fuel Mix Fill Cap
Cylinder Cover
Throttle
Lockout Direction
Rear
X., of Travel
X_ Chain Chain
Handle
CRi:IFTSI4RN"
Idle
Primer Bulb
Throttle Clutch Cover
Trigger Bar Nuts
ON/STOP SWITCH
The ON/STOP SWITCH is used to stop
the engine.
THROTTLE TRIGGER
The THROTi-LE TRIGGER controls en-
gine speed.
THROTTLE LOCK-OUT
The THROTFLE LOCK-OUT must be
pressed before you can squeeze the
throttle trigger. This feature prevents you
from accidentally squeezing the trigger.
CHOKE/FAST IDLE LEVER
The choke and fast idle are set by pull-
ing the CHOKE/FAST IDLELEVER out to
the full extent for cold starting or after
refueling. The choke provides additional
fuel to the engine during cold starting.
PRIMER BULB
The PRIMER BULB circulates fuel to the
carburetor to provide quicker starting.
Chain Guide Bar
Catcher
CHAIN BRAKE
The CHAIN BRAKE is a device designed
to stop the chain if kickback occurs. The
chain brake activates automatically in
the event of kickback. The chain brake
activates manually if the front hand
guard is pushed forward. The chain
brake is disengaged by pulling the front
hand guard back toward the front handle
as far as possible.
CHAIN TENSION
It is normal for a new chain to stretch
during the first 15 minutes of operation.
You should check your chain tension
frequently, See CHAINTENSION under
the MAINTENANCE section.
_WARNING: Muffler is very hot
during and after use. Do not touch the
muffler or allow combustible material
such as dry grass or fuel to do so.
7
![](/html/30/3015/3015d12b6a705366770375a87b200d7de8749bbb0227504251b5ad1eee335445/bg8.png)
BEFORE STARTING ENGINE
_'WARNING: Be sure to read the
fuel handling information in the safety
rules section of this manual before you
begin. If you do not understand the
fuel handling information do not at-
tempt to fuel your unit. Seek help from
someone that does understand the in-
formation or call the customer assis-
tance help line at 1-800-235-5878.
GUIDE BAR AND CHAIN OIL
The bar and chain require lubrication.
The chain oiler provides continuous
lubrication to the chain and guide bar.
Be sure to fill the bar oil tank when you
fill the fuel tank (Capacity = 6.8 ft. oz.).
Lack of oil will quickly ruin the bar and
chain. Too little oil will cause overheat-
ing shown by smoke coming from the
chain and/or discoloration of the bar.
For maximum guide bar and chain life,
we recommend you use Craftsman
chain saw bar oil. If Craftsman bar oil
is not available, you may use a good
grade SAE 30 oil until you are able to
obtain Craftsman brand. The oil output
is automatically metered during opera-
tion. Your saw will use approximately
one tank of bar oil for every tank of fuel
mix. Always fill the bar oil tank when
you fill the fuel tank.
FUELING ENGINE
_WARNING: Remove fuel cap
slowly when refueling.
This engine is certified to operate on
unleaded gasoline. Before operation,
gasoline must be mixed with a good
quality synthetic 2-cycle air-cooled en-
gine oil. We recommend Craftsman
brand synthetic oil. Mix gasoline and
oil at a ratio of 40:1. A 40:1 ratio is ob-
tained by mixing 3.2 ounces of oil with
1 gallon of unleaded gasoline. Included
with this saw is a 3.2 ounce container of
oil. Pour the entire contents of this con-
tainer into 1 gallon of gasoline to
achieve the proper fuel mixture.
DO NOT USE automotive or boat oil.
These oils will cause engine damage.
When mixing fuel follow the instruc-
tions printed on the oil container. Once
oil is added to the gasoline, shake
container momentarily to assure that
the fuel is thoroughly mixed. Always
read and follow the safety rules relat-
ing to fuel before fueling your unit.
IMPORTANT
Experience indicates that alcohol-
blended fuels (called gasohol or using
ethanol or methanol) can attract mois-
ture which leads to separation and
formation of acids during storage. Acidic
gas can damage the fuel system of an
engine while in storage. To avoid engine
problems, the fuel system should be
emptied before storage for 30 days or
longer. Drain the gas tank, start the en-
gine and let it run until the fuel lines and
carburetor are empty. Use fresh fuel
next season. Never use engine or car-
buretor cleaner products in the fuel tank
or permanent damage may occur.
See the STORAGE section for additional
information
CHAIN BRAKE
Ensure chain brake is disengaged by
pulling the front hand guard back toward
the front handle as far as possible. The
chain brake must be disengaged before
cutting with the saw.
_IWARNING: The chain must not
move when the engine runs at idle
speed. If the chain moves at idle
speed refer to CARBURETOR ADJUST-
MENT within this manual. Avoid contact
with the muffler. A hot muffler can
cause serious burns.
STOPPING YOUR ENGINE
• Release tile throttle trigger.
• Move ON/STOP switch to the STOP
position.
STARTING POSITION
• To start the engine, bold tile saw
firmly on the ground as illustrated.
Make sure the chain is free to turn
without contacting any object.
Starter Rope Handle
Left Hand
on Front
Handle
Right Foot Through Rear Handle
IMPORTANT POINTS TO REMEMBER
When pulling the starter rope, do not
use the full extent of the rope as this
can cause the rope to break. Do not let
starter rope snap back. Hold the han-
dle and let the rope rewind slowly.
![](/html/30/3015/3015d12b6a705366770375a87b200d7de8749bbb0227504251b5ad1eee335445/bg9.png)
Forcoldweatherstarting,starttheunit
atFULLCHOKE;allowtheengineto
warmupbeforesqueezingthethrottle
trigger.
NOTE:Donotattempttocutmaterial
withthechoke/fastidleleverintheFULL
CHOKEposition.
STARTING A COLD ENGINE (or warm
engine after running out of fuel)
NOTE: In the following steps, when the
choke/fast idle lever is pulled out to the
full extent, the correct throttle setting for
starting is set automatically.
IGNITION
SWITCH
ON
STOP
\\ Lever
1. Move ON/STOP switch to the ON
position.
2. Pull choke/fast idle lever out to the
full extent (to the FULL CHOKE posi-
tion).
3. Slowly press primer bulb 6 times.
4. Pull the starter rope sharply 5 times
with your right hand. Then, pro-
ceed to the next step.
NOTE: If the engine sounds as if it is try-
ing to start before the 5th pull, stop pull-
ing and immediately proceed to the next
step.
5. Push the choke/fast idle lever in to
the HALF CHOKE position.
CHOKE/FAST IDLE LEVER
OFF
HALF
FULL
6. Pull the starter rope sharply with
your right hand until the engine
starts.
7. Allow the engine to run for approxi-
mately 30 seconds. Then, squeeze
and release the throttle trigger to
allow engine to return to idle
speed.
STARTING A WARM ENGINE
1. Move ON/STOP switch to the ON
position.
2. Pull the choke/fast idle lever out to
the FULL CHOKE position to set the
fast idle, then push the lever in to
the HALF CHOKE position.
3. Slowly press primer bulb 6 times.
4. Pull the starter rope sharply with
your right hand until the engine
starts.
5. Squeeze and release throttle trigger
to allow engine to return to idle
speed.
DIFFICULT STARTING (or starting a
flooded engine)
The engine may be flooded with too
much fuel if it has not started after 10
pulls.
Flooded engines can be cleared of ex-
cess fuel by pushing the choke/fast
idle lever in completely (to the OFF
CHOKE position) and then following the
warm engine starting procedure listed
above. Ensure the ON/STOP switch is
in the ON position.
Starting could require pulling the start-
er rope handle many times depending
on how badly the unit is flooded. If en-
gine fails to start, refer to the TROU-
BLESHOOTING TABLE or call
1-800-235-5878.
CHAIN BRAKE
_,WARNING: If the brake band is
worn too thin it may break when the
chain brake is triggered. With a broken
brake band, the chain brake will not
stop the chain. The chain brake must
be replaced if any part is worn to less
than 0.020" (0.5 mm) thick. Repairs on
a chain brake should be made by your
Sears Service Center. Take your unit
to the place of purchase or to the near-
est Sears Service Center.
• This saw is equipped with a chain
brake. The brake is designed to stop
the chain if kickback occurs.
• The inertia-activated chain brake is
activated if the front hand guard is
pushed forward, either manually (by
hand) or automatically (by sudden
movement).
• If the brake is already activated, it is
disengaged by pulling the front hand
guard back toward the front handle
as far as possible.
• When cutting with the saw, the chain
brake must be disengaged.
9
![](/html/30/3015/3015d12b6a705366770375a87b200d7de8749bbb0227504251b5ad1eee335445/bga.png)
Disengaged
Engaged
Braking function control
CAUTION: The chain brake must be
checked several times daily. The en-
gine must be running when performing
this procedure. This is the only
instance when the saw should be
placed on the ground with the engine
running.
Place the saw on firm ground. Grip the
rear handle with your right hand and
the front handle with your left hand.
Apply full throttle by fully depressing
the throttle trigger. Activate the chain
brake by turning your left wrist against
the hand guard without releasing your
grip around the front handle. The chain
should stop immediately.
Inertia activating function control
_WARNING: When performing
the following procedure, the engine
must be turned off.
Grip the rear handle with your right hand
and the front handle with your left hand.
Hold the chain saw approximately 14
inches (35 cm) above a stump or other
wooden surface. Release your grip on
the front handle and use the weight of
the saw to let the top of the guide bar
fall forward and contact the stump.
When the tip of the bar hits the stump,
the brake should activate.
OPERATING TIPS
• Check chain tension before first use
and after 1 minute of operation. See
CHAIN TENSION in the MAINTENANCE
section.
• Cut wood only. Do not cut metal, plas-
tics, masonry, non-wood building ma-
terials, etc.
• Stop the saw if the chain strikes a
foreign object. Inspect the saw and
repair or replace parts as necessary.
• Keep the chain out of dirt and sand.
Even a small amount of dirt will quickly
dull a chain and thus increase the
possibility of kickback.
• Practice cutting a few small logs us-
ing the following techniques to get
the "feel" of using your saw before
you begin a major sawing operation.
• Squeeze the throttle trigger and allow
the engine to reach full speed before
cutting.
• Begin cutting with the saw frame
against the log.
• Keep the engine at full speed the
entire time you are cutting.
• Allow the chain to cut for you. Exert
only light downward pressure. If
you force the cut, damage to the
bar, chain, or engine can result.
• Release the throttle trigger as soon
as the cut is completed, allowing
the engine to idle. Ifyou run the saw
at full throttle without a cutting load,
unnecessary wear can occur to the
chain, bar, and engine. To maxi-
mize operating efficiency, do not
run the engine for longer than 30
seconds at a time at full throttle.
• To avoid losing control when cut is
complete, do not put pressure on
saw at end of cut.
• Stop the engine before setting the
saw down after cutting.
TREE FELLING TECHNIQUES
Ai_WARNING: Check for broken or
dead branches which can fall while cut-
ting causing serious injury. Do not cut
near buildings or electrical wires if you
do not know the direction of tree fall, nor
cut at night since you will not be ale to
see well, nor during bad weather such
as rain, snow, or strong winds, etc. If
the tree makes contact with any utility
line, the utility company should be noti-
fied immediately.
• Carefully plan your sawing operation
in advance.
• Clear the work area. You need a clear
area all around the tree so you can
have secure footing.
• The chain saw operator should keep
on the uphill side of the terrain as the
tree is likely to roll or slide downhill
after it is felled.
• Study the natural conditions that can
cause the tree to fall in a particular di-
rection.
Natural conditions that can cause a tree
to fall in a particular direction include:
• The wind direction and speed.
• The lean of the tree. The lean of a
tree might not be apparent due to un-
even or sloping terrain. Use a plumb
or level to determine the direction of
tree lean.
• Weight and branches on one side.
• Surrounding trees and obstacles.
lO
![](/html/30/3015/3015d12b6a705366770375a87b200d7de8749bbb0227504251b5ad1eee335445/bgb.png)
Look for decay and rot. If the trunk is
rotted, it can snap and fall toward the
operator. Check for broken or dead
branches which can fall on you while
cutting. Make sure there is enough
room for the tree to fall. Maintain a dis-
tance of 2-1/2tree lengths from the near-
est person or other objects. Engine
noise can drown out a warning call.
Remove dirt, stones, loose bark, nails,
staples, and wire from the tree where
cuts are to be made.
Plan a clear retreat path to the rear
and diagonal to the line of fall.
• After removing the wood from the
notch, make the felling cut on the op-
posite side of the notch. This is done
by making a cut about two inches (5
cm) higher than the center of the
notch. This will leave enough uncut
wood between the felling cut and the
notch to form a hinge. This hinge will
help prevent the tree from falling inthe
wrong direction.
Hinge holds tree on stump and helps
control fall
Opening
of felling
? Plan a clear retreat path
(}--_'- Direction of Fall
-t
45° / ._.
",.//o_
b¢,"_.€¢"
FELLING LARGE TREES
(6 h_ches(15 cm) h_diameter or larger)
The notch method is used to fell large
trees. A notch is cut on the side of the
tree in the desired direction of fall. After
a felling cut is made on the opposite
side of tree, the tree will tend to fall into
the notch.
NOTE: If the tree has large buttress
roots, remove them before making the
notch. If using saw to remove buttress
roots, keep saw chain from contacting
ground to prevent dulling of the chain.
NOTCH CUT AND FELLING THE
TREE
• Make notch cut by cutting the top of
the notch first. Cut through 1/3of the
diameter of the tree. Next complete
the notch by cutting the bottom of the
notch. See illustration. Once the
notch is cut remove the notch of
wood from the tree.
Final (felling) cut here, 2 inches
(5 era) above center of notch.
Firstout } ,z'; I /
I/
7
Closing of
notch
NOTE: Before felling cut is complete,
use wedges to open the cut if necessary
to control the direction of fall. To avoid
kickback and chain damage, use wood
or plastic wedges, but never steel or iron
wedges.
• Be alert to signs that the tree is
ready to fall: cracking sounds, widen-
ing of the felling cut, or movement in
the upper branches.
• As tree starts to fall, stop saw, put it
down, and get away quickly on your
planned retreat path.
• DO NOT cut down a partially fallen tree
with your saw. Be extremely cautious
with partially fallen trees that may be
poorly supported. When a tree doesn't
fall completely, set the saw aside and
pull down the tree with a cable winch,
block and tackle, or tractor.
CUTTING A FALLEN TREE
(BUCKING)
Bucking is tile term used for cutting a
fallen tree to the desired log size.
'd_WARNING: Do not stand on the
log being cut. Any portion can roll
causing loss of footing and control. Do
not stand downhill of the log being cut.
IMPORTANT POINTS
• Cut only one log at a time.
• Cut shattered wood very carefully;
sharp pieces of wood could be flung
toward operator.
• Use a sawhorse to cut small logs.
Never allow another person to hold
the log while cutting and never hold
the log with your leg or foot.
11
![](/html/30/3015/3015d12b6a705366770375a87b200d7de8749bbb0227504251b5ad1eee335445/bgc.png)
• Donotcutinanareawherelogs,
limbs,androotsaretangledsuchas
inablowndownarea.Dragthelogs
intoaclearareabeforecuttingby
pullingoutexposedandclearedlogs
first.
TYPES OF CUTTING USED FOR
BUCKING
WARNING: If saw becomes
pinched or hung in a log, don't try to
force it out. You can lose control of the
saw resulting in injury and/or damage
to the saw. Stop the saw, drive a
wedge of plastic or wood into the cut
until the saw can be removed easily.
Restart the saw and carefully reenter
the cut. To avoid kickback and chain
damage, do not use a metal wedge.
Do not attempt to restart your saw
when it is pinched or hung in a log.
Use a wedge to remove pinched saw
Turn saw OFF and use a plastic or
wooden wedge to force cutopen.
Overcutting begins on the top side of
the log with the bottom of the saw
against the log. When overcutting use
light downward pressure.
Second cut
First cut on compression side of log
BUCKING WITHOUT A SUPPORT
• Overcut through 1/3of the diameter
of the log.
• Roll the log over and finish with a
second overcut.
• Watch for logs with a compression
side to prevent the saw from pinch-
ing. See illustrations for cutting logs
with a compression side.
BUCKING USING A LOG OR
SUPPORT STAND
• Remember your first cut is always on
the compression side of the log.
(Refer to the illustrations below for
your first and second cut)
• Your first cut should extend t/3 of the
diameter of the log.
• Finish with your second cut.
Using a log for support
G;_ Und " "'._5
Undercutting involves cutting on the
underside of the log with top of saw
against the log. When undercutting
use light upward pressure. Hold saw
firmly and maintain control. The saw
will tend to push back toward you.
_.WARNING: Neverturn saw up-
side down to undercut, The saw can-
not be controlled in this position.
Always make your first cut on the com-
pression side of the log. The compres-
sion side of the log is where the pres-
sure of the log's weight is
concentrated.
Firstcut on compression side of log
Second cut
1st Cut
1st Cut
Using a support stand
2 nd Cut
l_
,2LZL_ _!k 1s_Cut
1st Cut
L
12
![](/html/30/3015/3015d12b6a705366770375a87b200d7de8749bbb0227504251b5ad1eee335445/bgd.png)
LIMBING AND PRUNING
_IWARNING: Be alert for and
guard against kickback. Do not allow the
moving chain to contact any other
branches or objects at the nose of the
guide bar when limbing or pruning. Al-
lowing such contact can result in serious
injury.
_WARNING: Never climb into a
tree to limb or prune. Do not stand on
ladders, platforms, a log, or in any posi-
tion which can cause you to lose your
balance or control of the saw.
IMPORTANT POINTS
• Work slowly, keeping both hands firmly
gripped on the saw. Maintain secure
footing and balance.
• Watch out for springpoles. Springpoles
are small size limbs which can catch
the saw chain and whip toward you or
pull you off balance. Use extreme cau-
tion when cutting small size limbs or
slender material.
• Be alert for springback. Watch out for
branches that are bent or under
pressure. Avoid being struck by the
branch or the saw when the tension
in the wood fibers is released.
• Keep a clear work area. Frequently
clear branches out of the way to avoid
tripping over them.
LIMBING
• Always limb a tree after it is cut
down. Only then can limbing be done
safely and properly.
• Leave the larger limbs underneath the
felled tree to support the tree as you
work.
• Start at the base of the felled tree and
work toward the top, cutting branches
and limbs. Remove small limbs with
one cut.
• Keep the tree between you and the
chain. Cut from the side of the tree
opposite the branch you are cutting.
• Remove larger, supporting branches
with the cutting techniques described
in BUCKING WITHOUT A SUPPORT
• Always use an overcut to cut small
and freely hanging limbs. Undercutting
could cause limbs to fall and pinch the
saw.
PRUNING
_ILWARNING: Limit pruning to limbs
shoulder height or below. Do not cut if
branches are higher than your shoulder.
Get a professional to do the job.
• Make your first cut 1/3of the way
through the bottom of the limb.
• Next make a 2nd cut all the way
through the limb. Then cut a third
overcut leaving a 1 to 2 inch (2.5 to 5
cm) collar from the truck of the tree.
_Thi_r_ic Second cut_" _ "
Collar tit_
"x_l_ _ Firstcut
/ Pruning technique
13
![](/html/30/3015/3015d12b6a705366770375a87b200d7de8749bbb0227504251b5ad1eee335445/bge.png)
CUSTOMER RESPONSIBILITIES
_WARNING: Disconnect the spark plug before performing maintenance
except for carburetor adjustments=
Fill in dates as you complete Before After Ever Every Service
regular service Use Use 5 hrs. 25 hrs. Yearly Dates
Check for damaged/worn parts _,
Check for loose fasteners/parts _'
Check chain tension _'
Check chain sharpness _'
Check guide bar _"
Check fuel mixture level _'
Check guide bar and chain oil _"
Inspect and clean unit & decals _"
Check chain brake _'
Clean guide bar groove _"
Clean air filter _'
Clean/inspect muffler and spark
arresting screen _'
Replace spark plug and fuel filter _'
GENERAL RECOMMENDATIONS
The warranty on this unit does not cov-
er items that have been subjected to
operator abuse or negligence. To re-
ceive full value from the warranty, the
operator must maintain unit as
instructed in this manual. Various ad-
justments will need to be made period-
ically to properly maintain your unit.
• Once a year, replace the spark plug,
air filter, and check guide bar and
chain for wear. A new spark plug and
air filter assures proper air-fuel mixture
and helps your engine run better and
last longer.
CHECK FOR DAMAGED OR
WORN PARTS
Contact your Sears Service Center for
replacement of damaged or worn parts.
NOTE: It is normal for a small amount of
oil to appear under the saw after engine
stops. Do not confuse this with a leaking
oil tank.
• ON/STOP Switch - Ensure ON/STOP
switch functions properly by moving
the switch to the STOP position. Make
sure engine stops; then restart engine
and continue=
• Fuel Tank - Do not use saw iffuel
tank shows signs of damage or leaks=
• Oil Tank - Do not use saw if oil tank
shows signs of damage or leaks.
CHECK FOR LOOSE
FASTENERS AND PARTS
• Bar Nuts
• Chain
• Muffler
• Cylinder Shield
• Air Filter
• Handle Screws
• Vibration Mounts
• Starter Housing
• Front Hand Guard
CHECK CHAIN TENSION
_lk WARNING: Wear protective
gloves when handling chain. The chain
is sharp and can cut you even when it is
not moving.
Chain tension is very important. Chains
stretch during use. This is especially true
during the first few times you use your
saw. Always check chain tension each
time you use and refuel your saw.
1. Use the screwdriver end of the
chain adjustment tool (bar tool) to
move chain around guide bar to
ensure kinks do not exist. The
chain should rotate freely.
14
![](/html/30/3015/3015d12b6a705366770375a87b200d7de8749bbb0227504251b5ad1eee335445/bgf.png)
Guide
Bar
Chain Adjustment
Bar Nuts Adjusting Tool
Screw (Bar Tool)
2. Loosen bar nuts until they are
finger tight against the clutch cover.
3. Turn adjusting screw clockwise un-
til chain solidly contacts bottom of
guide bar rail.
4. Using bar tool, roll chain around
guide bar to ensure all links are in
bar groove.
5. Lift up tip of guide bar to check for
sag. Release tip of guide bar, then
turn adjusting screw until sag does
not exist.
6. While lifting tip of guide bar, tighten
bar nuts securely with the bar tool.
Bar Nuts
7. Use the screwdriver end of the bar
tool to move chain around guide
bar.
8. If chain does not rotate, it is too
tight. Slightly loosen bar nuts and
loosen chain by turning the adjust-
ing screw 1/4 turn counterclock-
wise. Retighten bar nuts.
9. If chain is too loose, it will sag be-
low the guide bar. DO NOT operate
the saw if the chain is loose.
_,WARNING: If the saw is oper-
ated with a loose chain, the chain
could jump offthe guide bar and result
in serious injury.
CHECK CHAIN SHARPNESS
A sharp chain makes wood chips. A
dull chain makes a sawdust powder
and cuts slowly. See CHAIN SHARP-
ENING.
CHECK GUIDE BAR
Conditions which require guide bar
maintenance:
• Saw cuts to one side or at an angle.
• Saw has to be forced through the cut.
• Inadequate supply of oil to bar/chain.
Check the condition of guide bar each
time chain is sharpened. A worn guide
bar will damage the chain and make
cutting difficult.
After each use, ensure ON/STOP
switch is in the STOP position, then
clean all sawdust from the guide bar
and sprocket hole.
To maintain guide bar:
• Move ON/STOP switch to STOP.
• Loosen and remove bar nuts and
clutch cover. Remove bar and chain
from saw.
• Clean the oil holes and bar groove
after each 5 hours of operation.
Remove Sawdust From .,_
Guide Bar _ov_
Oil Holes o
• Burring of guide bar rails is a normal
process of rail wear. Remove these
burrs with a flat file.
• When rail top is uneven, use a flat
file to restore square edges and
sides.
r_ File Rail Edges_ [7 I7
and Sides I U I
Square ] ]
Worn Groove Correct Groove
Replace guide bar when the groove is
worn, the guide bar is bent or cracked,
or when excess heating or burring of the
rails occurs. If replacement is necessary,
use only the guide bar specified for your
saw in the repair parts list or on the de-
cal located on the chain saw.
CHECK FUEL MIXTURE LEVEL
• See FUELING ENGINE under the OP-
ERATION section.
15