Craftsman 351220200 Owner’s Manual
Operator's Manual
GRINDER STAND
Model No.
351.220200
• Safety
• Assembly
CAUTION: Read and follow
all Safety Rules and Operating
Instructions before First Use
of this Product.
Sears Brands Management Corp., Hoffman Estates, IL 60179 U.S.A.
www.sears.com/craftsman
31275.00 Draft (09/30/09)
• Operation
• Parts List
• Espa5ol
Warranty ....................... 2 Operation ...................... 3
Safety Rules .................... 2 Parts Illustration and List ........ 4-5
Assembly ...................... 3 Espa_ol ...................... 6-7
ONE-YEAR FULL WARRANTY ON CRAFTSMAN TOOL
If this Craftsman tool fails due to a defect in material or workmanship within
one year from the date of purchase, call 1-800-4-MY-HOME® TO ARRANGE
FOR FREE REPAIR (or replacement if repair proves impossible).
If this tool is ever used for commercial or rental purposes, this warranty will
apply for only 90 days from the date of purchase.
This warranty gives you specific legal rights and you may also have other
rights which vary from state to state.
Sears, Roebuck and Co., Dept. 817WA, Hoffman Estates, IL 60179
PROPOSITION 65 WARNING: Some
dust created by power sanding, sawing,
grinding, drilling and other construction
activities contains chemicals known to
the state of California to cause cancer,
birth defects or other reproductive
harm.
Some examples of these chemicals are:
• Lead from lead-based paints.
• Crystalline silica from bricks and
cement and other masonry products.
• Arsenic and chromium from chemi-
cally-treated lumber.
Your risk from these exposures vary,
depending on how often you do this
type of work. To reduce your exposure
to these chemicals: work in a well
ventilated area and work with approved
safely equipment. Always wear OSHA/
NIOSH approved, properly fitting face
mask or respirator when using such
tools.
©Sears, Roebuck and Co. 2
. Know the tool stand and the power
tool. Read and understand opera-
tor's manuals and other instructions
provided.
. Securely bolt tool stand to floor.
. Use only accessories designed
for your tool stand or power tool.
. Make sure power tools and acces-
sories are securely clamped.
. Always check your set up. For
example, rotate accessory by
hand before applying power.
. Keep your mind on your work.
Be alert.
. Dress properly. Do not wear jewelry,
gloves, or loose clothing.
. Wear a face shield or safety glasses.
. Never place hands in jeopardy.
Refer to Figure 2.
• Check for completeness. Locate all
parts before attempting assembly.
NOTE: Finger tighten fasteners until
all components are assembled. Then
tighten all fasteners securely.
• Attach a leg (Key No. 3) to the top
bracket (Key No. 6) using two pan
head screws and hex nuts (Key Nos.
2 and 5). Note: The leg attaches to
the outside of the bracket. Attach
another leg to the other side of the
bracket.
• Repeat the above procedure to build
another leg set.
• Attach the two leg sets to the slotted
top bracket (Key No. 7) with four pan
head screws and hex nuts. Note:
The slotted top bracket fits inside
the legs and over the top bracket.
DESCRIPTION
The Sears Model 220200 Grinder
Stand is constructed of 16 gauge
stamped steel, and is designed for use
with most bench grinders. Top has two
x 21/8"slots located 61/2"apart.
• Attach the remaining slotted top
bracket to the other side of the
leg sets.
• Attach the four braces (Key No. 4)
to the legs. Note: Braces attach
inside the legs with the flange
toward the top.
• Attach the four feet (Key No. 1) to
the legs.
• Place the stand upright on a level
surface, adjust feet and tighten
all fasteners securely.
MOUNT GRINDER
• Use hex head bolts with flat wash-
ers, lock washers and hex nuts
to secure grinder to stand top
(Key Nos. 8, 9, 10 and 11).
o
SPECIFICATIONS
Shipping Weight ............. 14 Ibs
Weight Capacity ............ 220 Ibs
DIMENSIONS
Refer to Figure 1.
Base width ............... 18 x 18"
Height ..................... 31W'
Table size ............... 91/2x 91/2"
3174"
18 _'
Figure 1- Dimensions
Loading...